Highly sensitive determination of tetrabromobisphenol A and bisphenol A in environmental water samples by solid‐phase extraction and liquid chromatography‐tandem mass spectrometry

Using bamboo‐activated charcoal as SPE adsorbent, a novel SPE method was developed for the sensitive determination of tetrabromobisphenol A and bisphenol A in environmental water samples by rapid‐resolution LC‐ESI‐MS/MS. Important parameters influencing extraction efficiency, including type of eluent, eluent volume, sample pH, volume and flow rate, were investigated and optimized. Under the optimal extraction conditions (eluent: 8 mL methanol, pH: 7; flow rate: 4 mL/min; sample volume: 100 mL), low LODs (0.01–0.02 ng/mL), good repeatability (6.2–8.3%) and wide linearity range (0.10–10 ng/mL) were obtained. Satisfied results were achieved when the proposed method was applied to determine the two target compounds in real‐world environmental water samples with spiked recoveries over the range of 80.5–119.8%. All these facts indicate that trace determination of tetrabromobisphenol A and bisphenol A in real‐world environmental water samples can be realized by bamboo‐activated charcoal SPE‐rapid resolution‐LC‐ESI‐MS/MS.     

Identification and determination of the saikosaponins in Radix bupleuri by accelerated solvent extraction combined with rapid‐resolution LC‐MS

A method based on accelerated solvent extraction combined with rapid‐resolution LC–MS for efficient extraction, rapid separation, online identification and accurate determination of the saikosaponins (SSs) in Radix bupleuri (RB) was developed. The RB samples were extracted by accelerated solvent extraction using 70% aqueous ethanol v/v as solvent, at a temperature of 120°C and pressure of 100 bar, with 10 min of static extraction time and three extraction cycles. Rapid‐resolution LC separation was performed by using a C₁₈ column at gradient elution of water (containing 0.5% formic acid) and acetonitrile, and the major constituents were well separated within 20 min. A TOF‐MS and an IT‐MS were used for online identification of the major constituents, and 27 SSs were identified or tentatively identified. Five major bioactive SSs (SSa, SSc, SSd, 6″‐O‐acetyl‐SSa and 6″‐O‐acetyl‐SSd) with obvious peak areas and good resolution were chosen as benchmark substances, and a triple quadrupole MS operating in multiple‐reaction monitoring mode was used for their quantitative analysis. A total of 16 RB samples from different regions of China were analyzed. The results indicated that the method was rapid, efficient, accurate and suitable for use in the quality control of RB.     

Dispersive Micro Solid‐phase Extraction Coupled with Ultrasound‐assisted Solvent Desorption for Determination of Synthetic Polycyclic and Nitro‐aromatic Musks in Aqueous Samples

An optimized method for the determination of five synthetic polycyclic: celestolide (ADBI), phantolide (AHMI), traseolide (ATII), galaxolide (HHCB), tonalide (AHTN), and two nitro‐aromatic musks: musk xylene (MX) and musk ketone (MK), in water samples is described. The method involves a dispersive micro solid‐phase extraction (D‐μ‐SPE) plus ultrasound‐assisted solvent desorption (UASD) prior to their determination by gas chromatography‐mass spectrometry (GC‐MS) using the selected ion storage (SIS) mode. Factors affecting the extraction efficiency of the target analytes from water samples and ultrasound‐assisted solvent desorption were optimized by a Box‐Behnken design method. The optimal extraction conditions involved immersing 10.1 mg of a typical octadecyl (C18) bonded silica adsorbent (i.e., ENVI‐18) in a 50 mL water sample. After 10.4 min of extraction by vigorously shaking, the adsorbent was collected and dried on a filter, and the target musks were desorbed by ultrasound‐assisted for 38 sec with n‐hexane (200 μL) as the desorption solvent. A 10 μL aliquot was then directly determined by large‐volume injection GC‐MS. The limits of quantitation (LOQs) were 1.2 to 5 ng/L. The precision for these analytes, as indicated by relative standard deviations (RSDs), were less than 11% for both intra‐ and inter‐day analysis. Accuracy, expressed as the mean extraction recovery, was between 74% and 92%. A preliminary analysis of the effluents from municipal wastewater treatment plants (MWTP) and river water samples revealed that HHCB and AHTN were the two most commonly detected synthetic musks; their concentration were determined to range from 88 to 690 ng/L for effluent samples, and 5 to 320 ng/L for river water samples. This is a simple, low cost, effective, and eco‐friendly analytical method.     

Efficient sample preparation method based on solvent‐assisted dispersive solid‐phase extraction for the trace detection of butachlor in urine and waste water samples

In this work, an efficient sample preparation method termed solvent‐assisted dispersive solid‐phase extraction was applied. The used sample preparation method was based on the dispersion of the sorbent (benzophenone) into the aqueous sample to maximize the interaction surface. In this approach, the dispersion of the sorbent at a very low milligram level was achieved by inserting a solution of the sorbent and disperser solvent into the aqueous sample. The cloudy solution created from the dispersion of the sorbent in the bulk aqueous sample. After pre‐concentration of the butachlor, the cloudy solution was centrifuged and butachlor in the sediment phase dissolved in ethanol and determined by gas chromatography with flame ionization detection. Under the optimized conditions (solution pH = 7.0, sorbent: benzophenone, 2%, disperser solvent: ethanol, 500 μL, centrifuged at 4000 rpm for 3 min), the method detection limit for butachlor was 2, 3 and 3 μg/L for distilled water, waste water, and urine sample, respectively. Furthermore, the preconcentration factor was 198.8, 175.0, and 174.2 in distilled water, waste water, and urine sample, respectively. Solvent‐assisted dispersive solid‐phase extraction was successfully used for the trace monitoring of butachlor in urine and waste water samples.     

A Microwave‐assisted Headspace Solid‐phase Microextraction for Rapid Determination of Synthetic Polycyclic and Nitro‐aromatic Musks in Fish Samples

Rapid solvent‐free microwave‐assisted headspace solid‐phase microextraction (MA‐HS‐SPME) coupled with gas chromatography‐mass spectrometry (GC‐MS) was developed to determine synthetic polycyclic and nitro‐aromatic musks in fish samples. Four commonly used synthetic musks, galaxolide (HHCB), tonalide (AHTN), musk xylene (MX) and musk ketone (MK) were employed in the method development and validation. The parameters (microwave irradiation time, irradiation power, amount of water addition, pH value and addition of NaCl) affecting the extraction efficiency of analytes from fish slurry were systematically investigated and optimized. The best extraction conditions were achieved when the fish sample 2‐g mixed with 4‐mL methanol and 15‐mL deionized water (containing 4 g of NaCl, pH 2.0 in a 40‐mL sample‐vial) was microwave irradiated at 80 watt for 5 min. The limits of quantification (LOQ) were 0.4 to 1.2 ng/g in 2‐g of wet tissue. The precision for these analytes, as indicated by relative standard deviations, were less than 9% for both intra‐ and inter‐day analysis. Accuracy, expressed as the mean extraction recovery, was between 80 to 92%. A standard addition method was used to quantitate these four synthetic musks, and the total concentrations ranged from 2.1 to 23.1 ng/g in various fish samples.     

Development of an ASE‐GC‐MS/MS method for detecting dinitolmide and its metabolite 3‐ANOT in eggs

An accelerated solvent extraction coupled with gas chromatography‐tandem mass spectrometry (ASE‐GC‐MS/MS) method for detecting dinitolmide residue and its metabolite (3‐amino‐2‐methyl‐5‐nitrobenzamide, 3‐ANOT) in eggs was developed and optimized. The samples were extracted using ASE with acetonitrile as the extractant and were purified by passage through a neutral alumina solid‐phase extraction column. Then, the samples were analyzed using the GC‐MS/MS method. The optimized method parameters were validated according to the requirements set forth by the European Union and the Food and Drug Administration. The average recoveries of dinitolmide and 3‐ANOT from eggs (egg white, egg yolk, and whole egg) at the limit of quantification (LOQ), 0.5 maximum residue limit (MRL), 1 MRL, and 2 MRL were 82.74% to 87.49%, the relative standard deviations (RSDs) were less than 4.63%, and the intra‐day RSDs and the inter‐day RSDs were 2.96% to 5.21% and 3.94% to 6.34%, respectively. The limits of detection and the LOQ were 0.8 to 2.8 μg/kg and 3.0 to 10.0 μg/kg, respectively. The decision limits (CC_α) were 3001.69 to 3006.48 μg/kg, and the detection capabilities (CC_β) were 3001.74 to 3005.22 μg/kg. Finally, the new method was successfully applied to the quantitative determination of dinitolmide and 3‐ANOT in 50 commercial eggs from local supermarkets.     

Determination of Carbon‐based Engineered Nanoparticles in Marketed Fish by Microwave‐assisted Extraction and Liquid Chromatography‐atmospheric Pressure Photoionization‐tandem Mass Spectrometry

An optimized method for the determination of two major carbon‐based engineered nanoparticles (C₆₀ and C₇₀) in marketed fish samples is described. The method involves the use of microwave‐assisted extraction (MAE) coupled with liquid chromatography ‐ tandem mass spectrometry with atmospheric pressure photoionization (LC‐APPI‐MS/MS). Factors affecting the extraction efficiency of the analytes from fish samples were optimized by a central composite design method. The optimal extraction temperature and time for MAE were found to be 233 °C for 22 min, and the extraction solution was composed of toluene and acetone in a ratio of 4.64:1. The limits of quantitation (LOQs) were 0.1 and 0.05 ng/g for C₆₀ and C₇₀, respectively. The precision for these analytes at two spiked levels, as indicated by relative standard deviations (RSDs), were less than 10% for both intra‐ and inter‐day analysis. Accuracy, expressed as the mean extraction recovery, was between 85 and 98%. The method was further validated based on EU Commission Decision 2002/657/EC, including a decision limit (CCα) and detection capability (CCβ) for marketed fish samples.     

Simultaneous determination of triclosan,triclocarban, and transformation products of triclocarban in aqueous samples using solid‐phase micro‐extraction‐HPLC‐MS/MS

The presence of triclosan and triclocarban, two endocrine‐disrupting chemicals and antimicrobial agents, and transformation products of triclocarban, 1,3‐di(phenyl)urea, 1,3‐bis(4‐chlorophenyl)urea and 1,3‐bis(3,4‐dichlorophenyl)urea, in tap water, treated household drinking water, bottled water, and river water samples were investigated using solid‐phase micro‐extraction coupled with‐HPLC‐MS/MS, a rapid, green, and sensitive method. Factors influencing the quantity of the analytes extracted onto the solid‐phase micro‐extraction fiber, such as addition of salt, sample pH, extraction time, desorption time, and sample volume, were optimized using solid‐phase micro‐extraction‐HPLC‐MS/MS. The results showed that the method gave satisfactory sensitivities and precisions for analyzing sub‐part‐per‐trillion levels of triclosan, triclocarban, and transformation products of triclocarban in samples collected locally. The recoveries of analytes ranged from 97 to 107% for deionized water samples, and 99 to 110% for river water samples, and limits of detection were in the range of 0.32–3.44 and 0.38–4.67 ng/L for deionized water and river water samples, respectively. On average, the daily consumption of triclosan and triclocarban by an adult by consuming 2 liters of different types of drinking water were estimated to be in the range of 6.13–425 ng/day as a result of the concentrations of triclosan and triclocarban measured in this study.     

Temperature‐controlled ionic liquid dispersive liquid‐phase microextraction for the sensitive determination of triclosan and triclocarban in environmental water samples prior to HPLC‐ESI‐MS/MS

A novel dispersive liquid‐phase microextraction method without dispersive solvents has been developed for the enrichment and sensitive determination of triclosan and triclocarban in environmental water samples prior to HPLC‐ESI‐MS/MS. This method used only green solvent 1‐hexyl‐3‐methylimidazolium hexafluorophosphate as extraction solvent and overcame the demerits of the use of toxic solvents and the instability of the suspending drop in single drop liquid‐phase microextraction. Important factors that may influence the enrichment efficiencies, such as volume of ionic liquid, pH of solutions, extraction time, centrifuging time and temperature, were systematically investigated and optimized. Under optimum conditions, linearity of the method was observed in the range of 0.1–20 μg/L for triclocarban and 0.5–100 μg/L for triclosan, respectively, with adequate correlation coefficients (R>0.9990). The proposed method has been found to have excellent detection sensitivity with LODs of 0.04 and 0.3 μg/L, and precisions of 4.7 and 6.0% (RSDs, n=5) for triclocarban and triclosan, respectively. This method has been successfully applied to analyze real water samples and satisfactory results were achieved.     

Decyl‐perfluorinated magnetic mesoporous microspheres for extraction and analysis perfluorinated compounds in water using ultrahigh‐performance liquid chromatography–mass spectrometry

In this work, the interior‐walls decyl‐perfluorinated functionalized magnetic mesoporous microspheres (F₁₇–Fe₃O₄@mSiO₂) were synthesized for the first time, and applied as adsorbents to extract and concentrate perfluorinated compounds (PFCs) from water samples. The fluorous functionalized interior pore‐walls contributed to the high‐selective preconcentration of PFCs due to fluorous affinity; and abundant silanol groups on the exterior surface of microspheres contributed to the good dispersibility in water sample. Four kinds of PFCs were selected as model analytes, including perfluorooctanoic acid, perfluorononanoic acid, perfluorododecanoic acid, and perfluorooctane sulphonate. In addition, UHPLC‐ESI/MS/MS was introduced to the fast and sensitive detection of the analytes after sample pretreatment. Important parameters of the extraction procedure were optimized, including salinity, eluting solvent, the amount of F₁₇–Fe₃O₄@mSiO₂ microspheres, and extraction time. The optimized procedure took only 10 min to extract analytes with high recoveries and merely 800‐μL acetonitrile to elute analytes from the magnetic adsorbents. Validation experiments showed good linearity (0.994–0.998), precision (2.6–7.6%), high recovery (93.4–105.7%) of the proposed method, and the limits of detection were from 0.008 to 0.125 μg/L. The F₁₇–Fe₃O₄@mSiO₂ magnetic microspheres have the advantages of great dispersibility in aqueous solution, high specificity of extraction, large surface area, and efficient separation ability. The results showed that the proposed method based on F₁₇–Fe₃O₄@mSiO₂ microspheres is a simple, fast, and sensitive tool for the analysis of PFCs in water sample.     

Validation of a liquid chromatography‐triple quadrupole mass spectrometric method for the determination of 5‐nitro‐5′‐hydroxy‐indirubin‐3′‐oxime (AGM‐130) in human plasma and its application to microdose clinical trial

A liquid chromatography–triple quadrupole mass spectrometric (LC‐MS/MS) method was developed and validated for the determination of 5‐nitro‐5′‐hydroxy‐indirubin‐3′‐oxime (AGM‐130) in human plasma to support a microdose clinical trial. The method consisted of a liquid–liquid extraction for sample preparation and LC‐MS/MS analysis in the positive ion mode using TurboIonSpray^TM for analysis. d₃‐AGM‐130 was used as the internal standard. A linear regression (weighted 1/concentration) was used to fit calibration curves over the concentration range of 10–2000 pg/mL for AGM‐130. There were no endogenous interference components in the blank human plasma tested. The accuracy at the lower limit of quantitation was 96.6% with a precision (coefficient of variation, CV) of 4.4%. For quality control samples at 30, 160 and 1600 pg/mL, the between run CV was ≤5.0 %. Between‐run accuracy ranged from 98.1 to 101.0%. AGM‐130 was stable in 50% acetonitrile for 168 h at 4°C and 6 h at room temperature. AGM‐130 was also stable in human plasma at room temperature for 6 h and through three freeze–thaw cycles. The variability of selected samples for the incurred sample reanalysis was ≤12.7% when compared with the original sample concentrations. This validated LC‐MS/MS method for determination of AGM‐130 was used to support a phase 0 microdose clinical trial. Copyright © 2015 John Wiley & Sons, Ltd.     

Single‐drop microextraction followed by in‐syringe derivatization and GC‐MS detection for the determination of parabens in water and cosmetic products

A single‐drop microextraction (SDME) method followed by in‐syringe derivatization and GC‐MS determination has been developed for analysis of five parabens, including methyl, ethyl, isopropyl, n‐propyl and n‐butyl paraben in water samples and cosmetic products. N,O‐Bis(trimethylsilyl)acetamide (BSA) was used as derivatization reagent. Derivatization reaction was performed inside the syringe barrel using 0.4 μL of BSA. Parameters that affect the derivatization yield such as temperature and time of the reaction were studied. In addition, experimental SDME parameters such as selection of organic solvent, addition of salt, extraction time and extraction temperature were investigated and optimized. The RSD of the method for aqueous samples varied from 8.1 to 13%. The LODs ranged from 0.001 (n‐butyl paraben) to 0.015 (methyl paraben) μg/L, and the enrichment factors were between 23 and 150.     

Rapid preparative separation of six bioactive compounds from Gentiana crassicaulis Duthie ex Burk. using microwave‐assisted extraction coupled with high‐speed counter‐current chromatography

A rapid method combining microwave‐assisted extraction (MAE) and high‐speed counter‐current chromatography (HSCCC) was applied for preparative separation of six bioactive compounds including loganic acid ( I ), isoorientin‐4′‐O‐glucoside ( II ), 6′‐O‐β‐d ‐glucopyranosyl gentiopicroside ( III ), swertiamarin ( IV ), gentiopicroside ( V ), sweroside ( VI ) from traditional Tibetan medicine Gentiana crassicaulis Duthie ex Burk. MAE parameters were predicted by central composite design response surface methodology. That is, 5.0 g dried roots of G. crassicaulis were extracted with 50 mL 57.5% aqueous ethanol under 630 W for 3.39 min. The extract (gentian total glycosides) was separated by HSCCC with n‐butanol/ethyl acetate/methanol/1% acetic acid water (7.5:0.5:0.5:3.5, v/v/v/v) using upper phase mobile in tail‐to‐head elution mode. 16.3, 8.8, 12., 25.1, 40.7, and 21.8 mg of compounds I–VI were obtained with high purities in one run from 500 mg of original sample. The purities and identities of separated components were confirmed using HPLC with photo diode array detection and quadrupole TOF‐MS and NMR spectroscopy. The study reveals that response surface methodology is convenient and highly predictive for optimizing extraction process, MAE coupled with HSCCC could be an expeditious method for extraction and separation of phytochemicals from ethnomedicine.     

UPLC‐MS/MS based diagnostics for epithelial ovarian cancer using fully sialylated C4‐binding protein

Serum levels of fully sialylated C4‐binding protein (FS‐C4BP) are remarkably elevated in patients with epithelial ovarian cancer (EOC) and can be used as a marker to distinguish ovarian clear cell carcinoma from endometrioma. This study aimed to develop a stable, robust and reliable liquid chromatography–hybrid mass spectrometry (UPLC‐MS/MS) based diagnostic method that would generalize FS‐C4BP as a clinical EOC biomarker. Glycopeptides derived from 20 μL of trypsin‐digested serum glycoprotein were analyzed via UPLC equipped with an electrospray ionization time‐of‐flight mass spectrometer. This UPLC‐MS/MS‐based diagnostic method was optimized for FS‐C4BP and validated using sera from 119 patients with EOC and 127 women without cancer. A1958 (C4BP peptide with two fully sialylated biantennary glycans) was selected as a marker of FS‐C4BP because its level in serum was highest among FS‐C4BP family members. Preparation and UPLC‐MS/MS were optimized for A1958, and performance and robustness were significantly improved relative to our previous method. An area under the curve analysis of the FS‐C4BP index receiver operating characteristic curve revealed that the ratio between A1958 and A1813 (C4BP peptide with two partially sialylated biantennary glycans) reached 85%. A combination of the FS‐C4BP index and carbohydrate antigen‐125 levels further enhanced the sensitivity and specificity.     

Simultaneous determination of morphine‐6‐d‐glucuronide,morphine‐3‐d‐glucuronide and morphine in human plasma and urine by ultra‐performance liquid chromatography–tandem mass spectrometry: Application to M6G injection pharmacokinetic study

A robust ultra‐performance liquid chromatography–tandem mass spectrometry (UPLC–MS/MS) method for the determination of morphine‐6‐d ‐glucuronide (M6G), morphine‐3‐d ‐glucuronide (M3G) and morphine (MOR) in human plasma and urine has been developed and validated. The analytes of interest were extracted from plasma by protein precipitation. The urine sample was prepared by dilution. Both plasma and urine samples were chromatographed on an Acquity UPLC HSS T₃ column using gradient elution. Detection was performed on a Xevo TQ‐S tandem mass spectrometer in multiple reaction monitoring mode using positive electrospray ionization. Matrix interferences were not observed at the retention time of the analytes and internal standard, naloxone‐D5. The lower limits of quantitation of plasma and urine were 2/0.5/0.5 and 20/4/2 ng/mL for M6G/M3G/MOR, respectively. Calibration curves were linear over the concentration ranges of 2–2000/0.5–500/0.5–500 and 20–20,000/4–4000/2–2000 ng/mL for M6G/M3G/MOR in plasma and urine samples, respectively. The precision was <7.14% and the accuracy was within 85–115%. Furthermore, stability of the analytes at various conditions, dilution integrity, extraction recovery and matrix effect were assessed. Finally, this quantitative method was successfully applied to the pharmacokinetic study of M6G injection in Chinese noncancer pain patients.     

Determination of phthalate esters in liquor samples by vortex‐assisted surfactant‐enhanced‐emulsification liquid–liquid microextraction followed by GC–MS

A novel method using vortex‐assisted surfactant‐enhanced‐emulsification liquid–liquid microextraction has been developed for the extraction of phthalate esters (PAEs) in Chinese liquor samples prior to analysis by GC–MS. In the proposed method, a high‐density extraction solvent (carbon tetrachloride) was dispersed into samples with the aid of a surfactant (Triton X‐100) and vortex agitation, resulting in a short extraction equilibrium (30 s). After centrifugation, a single microdrop of solvent was easily collected for GC–MS analysis. Key factors that affected the extraction efficiency were optimized. Under the optimum conditions, linearity was found in the range from 0.05 to 50 μg/L. Coefficients of determination varied from 0.9938 to 0.9971. LODs, based on an S/N of 3, ranged from 4.9 to 13 ng/L. Enrichment factors varied from 140 to 184. Reproducibility and recoveries were assessed by testing a series of three liquor samples that were spiked with different concentration levels. Finally, the proposed method was successfully applied to the determination of PAEs in 16 Chinese liquor samples. In this work, high‐density‐solvent vortex‐assisted surfactant‐enhanced‐emulsification liquid–liquid microextraction was applied for the first time for the extraction of PAEs in Chinese liquor samples and was proved to be simple, rapid, and sensitive.     

A rapid method with ultra‐high‐performance liquid chromatography–tandem mass spectrometry for simultaneous determination of five type B trichothecenes in traditional Chinese medicines

A speedy and selective ultra‐HPLC‐MS/MS method for simultaneous determination of deoxynivalenol (DON), 3‐acetyldeoxynivalenol (3‐ADON), 15‐ADON, nivalenol and fusarenon X in traditional Chinese medicines (TCMs) was developed. The method was based on one‐step sample cleanup using reliable homemade cleanup cartridges. A linear gradient mobile‐phase system, consisting of water containing 0.2% aqueous ammonia and acetonitrile/methanol (90:10, v/v) at a flow rate of 0.4 mL/min, and an Acquity UPLC HSS T3 column (100 mm×2.1 mm, 1.8 μm) were employed to obtain the best resolution of the target analytes. [¹³C₁₅]–DON was used as the internal standard to accomplish as accurate as possible quantitation. The established method was further validated by determining the linearity (R²≥0.9990), sensitivity (LOQ, 0.29–0.99 μg/kg), recovery (88.5–119.5%) and precision (RSD≤15.8%). It was shown to be a suitable method for simultaneous determination of DON, 3‐ADON, 15‐ADON, nivalenol and fusarenon X in various TCM matrices. The utility and practical impact of the method was demonstrated using different TCM samples.     

Positional isomer differentiation of synthetic cannabinoid JWH‐081 by GC‐MS/MS

Like many new designer drugs of abuse, synthetic cannabinoids (SC) have structural or positional isomers which may or may not all be regulated under law. Differences in acute toxicity may exist between isomers which impose further burden in the fields of forensic toxicology, medicine and legislation. Isomer differentiation therefore becomes crucial from these standpoints as new designer drugs continuously emerge with just minor positional modifications to their preexisting analogs. The aim of this study was to differentiate the positional isomers of JWH‐081. Purchased standard compounds of JWH‐081 and its positional isomers were analyzed by gas chromatography‐electron ionization‐mass spectrometry (GC‐EI‐MS) first in scan mode to investigate those isomers who could be differentiated by EI scan spectra. Isomers with identical or near‐identical EI spectra were further subjected to GC‐tandem mass spectrometry (MS/MS) analysis with appropriate precursor ions. EI scan was able to distinguish 3 of the 7 isomers: 2‐methoxy, 7‐methoxy and 8‐methoxy. The remaining isomers exhibited near‐identical spectra; hence, MS/MS was performed by selecting m/z 185 and 157 as precursor ions. 3‐Methoxy and 5‐methoxy isomers produced characteristic product ions that enabled the differentiation between them. Product ion spectrum of 6‐methoxy isomer resembled that of JWH‐081; however, the relative ion intensities were clearly different from one another. The combination of EI scan and MS/MS allowed for the regioisomeric differentiation of the targeted compounds in this study. Copyright © 2015 John Wiley & Sons, Ltd.     

Simultaneous determination of ten flavonoids of crude and wine‐processed Radix Scutellariae aqueous extracts in rat plasma by UPLC‐ESI‐MS/MS and its application to a comparative pharmacokinetic study

Radix Scutellariae (RS) is a herbal medicine with various pharmacological activities to treat inflammation, respiratory and gastrointestinal infections, etc. In this study, a rapid, sensitive and selective UPLC‐ESI‐MS/MS method was developed for simultaneous determination of 10 flavonoids – scutellarin, scutellarein, chrysin, wogonin, baicalein, apigenin, wogonoside, oroxylin A‐7‐O‐glucuronide, oroxylin A and baicalin – from RS aqueous extracts in rat plasma with propyl paraben as internal standard (IS). Chromatographic separation was achieved on a C₁₈ column using gradient elution with the mobile phase consisting of methanol and water (containing 0.1% formic acid) at a flow rate of 0.2 mL/min. The detection was performed in multiple reaction monitoring mode using electrospray ionization in negative mode. The validated method showed good linearity over a wide concentration range (r >0.9935). The intra‐ and interday assay variabilities were <9.5% and <12.4% for all analytes, respectively. The extraction recovery ranged from 71.2 to 89.7% for each analyte and IS. This method was successfully applied to pharmacokinetic comparision after oral administration of crude and wine‐processed RS aqueous extracts. There were significant differences in some pharmacokinetic parameters of most analytes between crude and wine‐processed RS. This suggested that wine‐processing exerted effects absorption of most flavonoids. Copyright © 2014 John Wiley & Sons, Ltd.     

Sensitive LC‐MS‐MS method for the determination of tiopronin in human plasma

A highly selective and sensitive LC‐MS‐MS method was developed and validated to quantify tiopronin in human plasma, using fudosteine as the internal standard (IS). L ‐Cysteine and 1,4‐dithiothreitol (DTT) were used as the reducer and the stabilizer to release and stabilify tiopronin from a dimmer and mix forms with endogenous thiols in the treatment of plasma samples. After a simple liquid–liquid extraction with ethyl acetate in acidic condition, the post‐treatment samples were analyzed on a C₁₈ column interfaced with a triple‐quadruple tandem mass spectrometer using negative electrospray ionization. Methanol and water (40:60, v/v) were used as the isocratic mobile phase, with 0.2% formic acid and 1.0 mM tris (hydroxymethyl) aminomethane (Tris) in water. The method was validated to demonstrate the specificity, lower limit of quantification, accuracy and precision of measurements. The assay was linear over the concentration range 0.078–10 μg/mL. The correlation coefficients for the calibration curves ranged from 0.9980 to 0.9990. The intra‐ and inter‐day precisions, calculated from quality control samples, were not more than 10.49%. The method was employed in a pharmacokinetic study after oral administration of 200 mg tiopronin tablets to 24 healthy volunteers. Copyright © 2009 John Wiley & Sons, Ltd