Speciation analysis of chromium in natural water samples by electrothermal atomic absorbance spectrometry after separation/preconcentration with nanometer-sized zirconium oxide immobilized on silica gel

Silica gel was prepared by the sol–gel method, modified with nanometer-sized zirconium oxide, and this material was characterized by X-ray diffraction. A micro-column packed with silica gel modified with nanometer zirconium oxide as sorbent has been developed for the quantitative separation and preconcentration of trace amounts of chromium(III) prior to their determination by electrothermal atomic absorption spectrometry. Total chromium was determined after the reduction of chromium(VI) to chromium(III) by 10% (m/v) of aqueous ascorbic acid as reducing reagent. The adsorption capacity for chromium(III) was found to be 2.36 mg g⁻¹. The detection limit for chromium(III) was 15 ng L⁻¹ with an enrichment factor of 100. The relative standard deviation was 3.2% (n = 7, c = 2.0 ng mL⁻¹).     

Adsorptive anodic stripping voltammetry of zirconium(IV)-alizarin red S complex at a carbon paste electrode

A sensitive adsorptive anodic stripping procedure for the determination of trace zirconium at a carbon paste electrode (CPE) has been developed. The method is based on adsorptive accumulation of the Zr(IV)-alizarin red S(ARS) complex onto the surface of the CPE, followed by oxidation of adsorbed species. The optimal experimental conditions include the use of 0.10 mol · L⁻¹ ammonium acetate buffer (pH 4.3), ARS, an accumulation potential of 0.20 V (versus SCE), an accumulation time of 2 min, a scan rate of 200 mV · s⁻¹ and a second-order derivative linear scan mode. The oxidation peak for the complex appears at 0.69 V. The peak current is proportional to the concentration of Zr(IV) over the range of 1.0 × 10⁻⁹–2.0 × 10⁻⁷ mol · L⁻¹, and the detection limit is 3 × 10⁻¹⁰ mol · L⁻¹ for a 2 min adsorption time. The relative standard deviations (n = 8) for 5.0 × 10⁻⁸ and 5.0 × 10⁻⁹ mol · L⁻¹ Zr(IV) are 3.3 and 4.8%, respectively. The proposed method was applied to the determination of zirconium in ore samples with satisfactory results.     

Catalytic Spectrophotometric Determination of Molybdenum

Summary.  A highly selective, sensitive, and simple catalytic method for the determination of molybdenum in natural and waste waters was developed. It is based on the catalytic effect of Mo(VI) on the oxidation of 2-aminophenol with H₂O₂. The reaction is monitored spectrophotometrically by tracing the oxidation product at 430 nm after 10 min of mixing the reagents. Addition of 800 μg · cm⁻³ EDTA conferred high selectivity; however, interfering effects of Au(III), Cr(III), Cr(VI), and Fe(III) had to be eliminated by a reduction and co-precipitation procedure with SnCl₂ and Al(OH)₃. Mo(VI) shows a linear calibration graph up to 11.0 ng · cm⁻³; the detection limit, based on the 3S _b-criterion, is 0.10 ng · cm⁻³. The unique selectivity and sensitivity of the new method allowed its direct application to the determination of Mo(VI) in natural and waste waters. Received April 11, 2001. Accepted (revised) June 18, 2001     

Adsorption of metal anions of vanadium(V) and chromium(VI) on Zr(IV)-impregnated collagen fiber

The metal anions of vanadium (V) and chromium (VI) in aqueous solution can be effectively adsorbed by Zr(IV)-impregnated collagen fiber (ZrICF). The maximum adsorption capacity of V(V) takes place within the pH range of 5.0 to 8.0, while that of Cr(VI) is within the pH range of 6.0 to 9.0. When the initial concentration of metal ions was 2.00 mmol L⁻¹ and the temperature was 303 K, the adsorption capacity of V(V) on Zr-ICF was 1.92 mmol g⁻¹ at pH 5.0, and the adsorption capacity of Cr(VI) was 0.53 mmol g⁻¹ at pH 7.0. As temperature increased, the adsorption capacity of V(V) increased, while that of Cr(VI) was almost unchanged. The adsorption isotherms of the anionic species of V(V) and Cr(VI) can be fit by the Langmuir equation. The adsorption rate of V(V) follows the pseudo-first-order rate model, while the adsorption rate of Cr(VI) follows the pseudo-second-order rate model. Furthermore, ZrICF shows high adsorption selectivity to V(V) in the mixture solution of V(V) and Cr(VI). Practical applications of ZrICF could be expected in consideration of its performance in adsorption of V(V) and Cr(VI).     

Flavonol Derivatives for Determination of Cr(III) and W(VI)

 Simple, rapid, sensitive and selective methods for the determination of Cr(III) and W(VI) with flavonol derivatives in the presence of surface-active agents are proposed. In the pH ranges 3.4–4.2 and 1.9–2.5, the molar absorptivities of Cr(III)-morin-emulsifier S (EFA) and W(VI)-morin-polyvinylpyrrolidone (PVP) systems are 1.13×10⁵ and 2.13×10⁴ L mol⁻¹ cm⁻¹ at 435 and 415 nm, respectively. The Cr(III)-quercetin-PVP and W(VI)-quercetin-cetylpyridinium bromide (CPB) systems are formed in the pH ranges 4–4.6 and 2.2–2.8 with molar absorptivities 1.02×10⁵ and 9.02×10⁴ L. mol⁻¹ cm⁻¹ at 441 and 419 nm, respectively. The linear dynamic ranges for the determination of Cr(III) and W(VI) with morin in the presence of EFA and PVP are 0.03–0.46 and 0.71–8.1 μg mL⁻¹, respectively. The corresponding ranges with quercetin are 0.04–0.54 and 0.14–2.1 μg mL⁻¹ of Cr(III) and W(VI), respectively. The r.s.d (n = 10) for the determination of 0.25 and 3.7 μg mL⁻¹ of Cr(III) and W(VI) with morin and their detection limits are 0.88 and 0.99% and 0.016 and 0.63 μg mL⁻¹, respectively. Using quercetin, the r.s.d (n = 10) for 0.22 and 1.2 μg mL⁻¹ of Cr(III) and W(VI) and their detection limits are 0.92 and 0.91% and 0.015 and 0.08 μg mL⁻¹, respectively. The critical evaluation of the proposed methods is performed by statistical analysis of the experimental data. The proposed methods are applied to determine Cr in steel, non-ferrous alloys, wastewater and mud filtrate and to the determination of W in steel. Received March 8, 1999. Revision January 21, 2000.     

A catalytic adsorptive stripping voltammetric procedure for trace determination of Cr(VI) in natural samples containing high concentrations of humic substances

A simple and fast catalytic adsorptive stripping voltammetric procedure for trace determination of Cr(VI) in natural samples containing high concentrations of humic substances has been developed. The procedure for chromium determination in the presence of DTPA and nitrates was employed as the initial method. In order to enhance the selectivity vs. Cr(III) the measurements were performed at 40°C. Interference from dissolved organic matter such as humic and fulvic acids was drastically decreased by adding Amberlite XAD-7 resin to the voltammetric cell before the deaeration step. The whole procedure was applied to a single cell, which allowed monitoring of the voltammetric scan. Optimum conditions for removing humic and fulvic acids due to their adsorption on XAD-7 resin were evaluated. The use of XAD-7 resin also minimize interferences from various cationic, anionic, and nonionic surfactants. The calibration graph for Cr(VI) for an accumulation time of 30 s was linear in the range 5 × 10⁻¹⁰ to 5 × 10⁻⁸ mol L⁻¹. The relative standard deviation for determination of Cr(VI) at a concentration of 1 × 10⁻⁸ mol L⁻¹ was 3.5% (n = 5). The detection limit estimated from 3 times the standard deviation for low Cr(VI) concentrations and an accumulation time of 30 s was about 1.3 × 10⁻¹⁰ mol L⁻¹. The proposed method was successfully applied to Cr(VI) determination at trace levels in soil samples.     

Determination of Zirconium (IV) and Aluminium (III) in Waste Water

 Zirconium (IV) was determined spectrophotometrically by reaction with quercetin as primary ligand and oxalate as secondary ligand. Polyvinylpyrrolidone (PVP) was used as protective colloid to solubilize the formed zirconium quercetin oxalate ternary complex. The molar absorptivity of the 1:3:1 (zirconium–quercetin–oxalate) complex is 7.31 × 10⁴ L·mol⁻¹ cm⁻¹ at 430 nm with a stability constant of 8.2 × 10²⁰ and its detection limit is 0.16 mg/L. Beer’s law is rectilinear up to 1.46 mg/L of zirconium (IV). The sensitivity index is 1.25 ng cm⁻². The reaction of aluminium (III) with quercetin in presence of PVP as a surfactant has been studied spectrophotometrically. The molar absorptivity of the 1:3 (aluminium–quercetin) complex is 8.09 × 10⁴ × L·mol⁻¹·cm⁻¹ at 433 nm, its stability constant is 2.6 × 10¹³ with sensitivity index of 0.33 ng·cm⁻² and its detection limit is 0.08 mg/L. The optimal conditions for the quantitative determination of zirconium and aluminium were studied. The proposed methods are examined by statistical analysis of the experimental data. The methods are free from interference of most cations and anions. The proposed methods have been used to determine zirconium and aluminium in industrial waste water. Received May 30, 2001; accepted November 2, 2001; published online July 15, 2002     

Kinetic Determination of Iodide Based on its Effect on the Hydrogen Peroxide Oxidation of Triflupromazine

 A new selective, sensitive, and simple kinetic method is developed for the determination of trace amounts of iodide. The method is based on the catalytic effect of iodide on the reaction of triflupromazine (TFP) with H₂O₂. The reaction is followed spectrophotometrically by tracing the oxidation product at 498 nm within 1 min after addition of H₂O₂. The optimum reaction conditions are TFP (0.4 × 10⁻³ M), H₂SO₄ (1.0M), H₃PO₄ (2.0M), and H₂O₂ (1.6M) at 30°C. Following this procedure, iodide can be determined with a linear calibration graph up to 4.5 ng ċ cm⁻³ and a detection limit of 0.04 ng ċ cm⁻³, based on the 3 S_b criterion. The method can also be applied to the determination of iodate and periodate ions. Determination of as little as 0.2, 1.0, 2.0, and 4.0 ng ċ cm⁻³ of I⁻, IO₃ ^-, or IO₄ ^- in aqueous solutions gave an average recovery of 98% with relative standard deviations below 1.6% (n = 5). The method was applied to the determination of iodide in Nile river water and ground waters as well as in various food samples after alkaline ashing treatment. The method is compared with other catalytic spectrophotometric procedures for iodide determination.     

Kinetic Determination of Iodide Based on its Effect on the Hydrogen Peroxide Oxidation of Triflupromazine

Summary.  A new selective, sensitive, and simple kinetic method is developed for the determination of trace amounts of iodide. The method is based on the catalytic effect of iodide on the reaction of triflupromazine (TFP) with H₂O₂. The reaction is followed spectrophotometrically by tracing the oxidation product at 498 nm within 1 min after addition of H₂O₂. The optimum reaction conditions are TFP (0.4 × 10⁻³ M), H₂SO₄ (1.0M), H₃PO₄ (2.0M), and H₂O₂ (1.6M) at 30°C. Following this procedure, iodide can be determined with a linear calibration graph up to 4.5 ng ċ cm⁻³ and a detection limit of 0.04 ng ċ cm⁻³, based on the 3 S_b criterion. The method can also be applied to the determination of iodate and periodate ions. Determination of as little as 0.2, 1.0, 2.0, and 4.0 ng ċ cm⁻³ of I⁻, IO₃ ^-, or IO₄ ^- in aqueous solutions gave an average recovery of 98% with relative standard deviations below 1.6% (n = 5). The method was applied to the determination of iodide in Nile river water and ground waters as well as in various food samples after alkaline ashing treatment. The method is compared with other catalytic spectrophotometric procedures for iodide determination. Received January 19, 2001. Accepted (revised) March 12, 2001     

Chemiluminescence determination of chromium(III) and total chromium in water samples using the periodate-lucigenin reaction

A new chemiluminescence (CL) method combined with flow injection technique is described for the determination of Cr(III) and total Cr. It is found that a strong CL signal is generated from the reaction of Cr(III), lucigenin and KIO₄ in alkaline condition. The determination of total Cr is performed by pre-reduction of Cr(VI) to Cr(III) by using H₂SO₃. The CL intensity is linearly related to the concentration of Cr in the range 4.0 × 10⁻¹⁰–1.0 × 10⁻⁶ g mL⁻¹. The detection limit (3s _b) is 1 × 10⁻¹⁰ g mL⁻¹ Cr and the relative standard deviation is 1.9% (5.0 × 10⁻⁸ g mL⁻¹ of Cr(III) solution, n = 11). The method was applied to the determination of Cr(III) and total Cr in water samples and compared satisfactorily with the official method.     

Application of chitosan functionalized with 3,4-dihydroxy benzoic acid moiety for on-line preconcentration and determination of trace elements in water samples

Chitosan resin functionalized with 3,4-dihydroxy benzoic acid (CCTS-DHBA resin) was used as a packing material for flow injection (FI) on-line mini-column preconcentration in combination with inductively coupled plasma-atomic emission spectrometry (ICP-AES) for the determination of trace elements such as silver, bismuth, copper, gallium, indium, molybdenum, nickel, uranium, and vanadium in environmental waters. A 5-mL aliquot of sample (pH 5.5) was introduced to the minicolumn for the adsorption/preconcentration of the metal ions, and the collected analytes on the mini-column were eluted with 2 M HNO₃, and the eluates was subsequently transported via direct injection to the nebulizer of ICP-AES for quantification. The parameters affecting on the sensitivity, such as sample pH, sample flow rate, eluent concentration, and eluent flow rate, were carefully examined. Alkali and alkaline earth metal ions commonly existing in river water and seawater did not affect the analysis of metals. Under the optimum conditions, the method allowed the determination of metal ions with detection limits of 0.08 ng mL⁻¹ (Ag), 0.9 ng mL⁻¹ (Bi), 0.07 ng mL⁻¹ (Cu), 0.9 ng mL⁻¹ (Ga), 0.9 ng mL⁻¹ (In), 0.08 ng mL⁻¹ (Mo), 0.09 ng mL⁻¹ (Ni), 0.9 ng mL⁻¹ (U), and 0.08 ng mL⁻¹ (V). By using 5 mL of sample solution, the enrichment factor and collection efficiency were 8–12 fold and 96–102%, respectively, whereas the sample throughput was 7 samples/hour. The method was validated by determining metal ions in certified reference material of river water (SLRS-4) and nearshore seawater (CASS-4), and its applicability was further demonstrated to river water and seawater samples.     

DNA Quantification in Nanoliter Volumes

A novel method for the determination of proteins at nanogram levels was proposed based on the decrease of resonance light scattering (RLS) signal resulting from the interaction of dibromo-o-nitrophenylfluorone (DBONPF)-sodium lauroyl glutamate (SLG) with proteins. At pH 2.97, the decrease RLS intensity was proportional to the concentration of proteins in the range of nanogram levels with 3σ detection limits being 3.4 ng mL⁻¹ for bovine serum albumin (BSA), 1.7 ng mL⁻¹ for human serum albumin (HSA), 4.1 ng mL⁻¹ for γ-globulin (γ-IgG), 4.4 ng mL⁻¹ for egg albumin, 6.2 ng mL⁻¹ for pepsin (Pep) and 3.7 ng mL⁻¹ for α-chymotrypsin (Chy). The method is no protein-to-protein variability, simple, rapid, practical and relatively free from interference from coexisting substance, as well as much more sensitive than most of the reported methods. The proposed method was successfully applied to determine total protein in human serum samples.     

On-Line Solid Phase Extraction and Simultaneous Determination of Hafnium and Zirconium by ICP–Atomic Emission Spectroscopy

A new simple flow injection analysis (FIA) system is described for on-line preconcentration by solid phase extraction and simultaneous determination of Hf and Zr in different samples using inductively coupled plasma atomic emission spectroscopy with a charge coupling detector (CCD). Quinalizarin (QA) was loaded on an octadecyl silica-polyethylene mini-column for the retention of Hf and Zr ions in complexed form. A 0.3 M ammonium acetate was used as buffer for providing suitable conditions for complexation and increasing reproducibility. Retained ions on the solid phase were then eluted by a solution containing 3.0 M HCl and 0.5 M HNO₃. In this work, for reducing bandwidths of eluted ions, elution of minicolumn was carried out from opposite direction. The same solution was used as both carrier and eluent, in order to increase the reproducibility. The eluted ions were introduced into the conventional nebulizer of ICP–AES instrument. Effects of different parameters, including instrumental parameters of ICP and FIA were optimized. An enrichment factor of 330 for each analyte ion was obtained at a concentration level of 80 ppb. The detection limits of the proposed method for Hf and Zr were 0.16 ng mL⁻¹ and 0.04 ng mL⁻¹ respectively. The ability of the method for the recovery of Hf and Zr ions was tested in the presence of several diverse metal ions in a synthetic mixture and some real matrices. It was also applied to the determination of Zr and Hf ions in a standard soil and in a standard alloy as real samples.     

Inorganic Arsenic and Selenium Determination Using Miniaturised Isotachophoresis

A new method allowing the simultaneous determination of arsenic(V), selenium(IV) and selenium(VI) using miniaturised isotachophoresis has been developed. The method uses 0.02 M nitric acid buffered to pH 5.5 with histidine as the leading electrolyte. Using a miniaturised poly(methyl methacrylate) chip device with an integrated conductivity detector, separations of model samples and an industrial process stream sample were achieved. Limits of detection were calculated to be 0.85 mg L⁻¹ for arsenic(V), 0.95 mg L⁻¹ for selenium(IV) and 1.0 mg L⁻¹ for selenium(VI). A method for the analysis of arsenic(III), using a glycolic acid based leading electrolyte to eliminate carbonate interference is also presented.     

Nanometer-sized zirconium dioxide microcolumn separation/preconcentration of trace metals and their determination by ICP-OES in environmental and biological samples

A new method is proposed using a microcolumn (20 mm × 2.0 mm) packed with nanometer-sized zirconia as solid-phase extractor for the separation/preconcentration of Mn, Cu, Cr, Zn, Ni and Co prior to their determination by inductively coupled plasma optical emission spectrometer (ICP-OES) in environmental samples. The factors affecting the separation and preconcentration of analytes such as pH, sample flow rate and volume, eluent concentration and volume were determined, interfering ions were studied, and the optimal experimental conditions were established. The adsorption capacity of nanometer-sized ZrO₂ for Mn, Cu, Cr, Zn, Ni and Co was found to be 1.3, 1.3, 1.7, 2.0, 3.9 and 1.5 mg g⁻¹, respectively. The detection limits of the method were 12, 58, 24, 2, 7 and 36 ng L⁻¹, respectively, with a preconcentration factor of 25. The precision of this method was 1.7% (Mn), 2.9% (Cu), 5.9% (Mn), 3.8% (Mn), 6.2% (Mn) and 4.3% (Mn) with 9 determinations of 10 ng mL⁻¹ of target analytes, respectively. The method was successfully applied to the determination of trace metals in lake water, dried fish samples, certified reference materials of human hair and milk, and provided satisfactory results.     

Solid-phase spectrophotometric microdetermination of iron with ascorbic acid and ferrozine

 A very sensitive and selective method for the determination of trace amounts of iron has been developed, based on the reduction of Fe(III) to Fe(II) by ascorbic acid, followed by chromogenic chelation of Fe(II) with ferrozine. The complex Fe(II)-ferrozine is easily sorbed on a dextran-type anion-exchange gel packed in a 1 mm cell, and the absorbance of the gel is measured directly at 569 and 800 nm. The extended linear range of the determination is 0.5–10 ng ml^-1 of iron (apparent molar absorptivity=4.4×10⁷ l mol^-1 cm^-1) and the precision (RSD) 1.3% for a concentration of 5 ng ml^-1 of iron (n=10). The detection limit for a sample volume of 1000 ml, using 0.040 g of anion-exchanger, corresponds to 0.12 ng ml^-1. The method has been successfully applied to the determination of iron in natural and waste waters, wine, soil extract and previously digested vegetal tissues, drugs and human hair. Received: 20 November 1995/Revised: 23 January 1996/Accepted: 26 January 1996     

Flow injection fluorimetric determination of chromium(VI) in electroplating baths by luminescence quenching of tris(2,2'-bipyridyl) ruthenium(II)

A sensitive and selective luminescence quenching method is developed and used for manual and flow injection analysis (FIA) of chromium(VI) by reaction with [Ru(bpy)₃]²⁺. The emission peak of ruthenium(II) at 595 nm is linearly decreased as a function of Cr(VI) concentration. This permits determination of chromium(VI) ion over the concentration range 0.1-20 μg ml⁻¹ with a detection limit of 33 ng ml⁻¹. The quenching process is due to an electron transfer from the luminescent [Ru(bpy)₃]²⁺ complex ion to Cr(VI) resulting in the formation of the non-luminescent [Ru(bpy)₃]³⁺ complex ion. Selectivity for Cr(VI) over many anions and transition, alkali and alkaline earth metal cations is demonstrated. High concentration levels of sulphate, chloride, borate, acetate, phosphate, nitrate, cyanide, Pb²⁺, Zn²⁺, Hg²⁺, Cu²⁺, Cd²⁺, Ni²⁺ and Mn²⁺ ions are tolerated. The effects of solution pH and [Ru(bpy)₃]²⁺ reagent concentration are examined and the reaction conditions are optimized. Validation of the method according to the quality assurance standards show suitability of the proposed method for use in the quality control assessment of Cr(VI) in complex matrices without prior treatment. The method is successfully applied to determine chromium(VI) in electroplating baths using flow injection analysis. Results with a mean standard deviation of ±0.6% are obtained which compare fairly well with data obtained using atomic absorption spectrometry.     

Comparison of Pyrolysis and Microwave Acid Digestion Techniques for the Determination of Mercury in Biological and Environmental Materials

 Microwave digestion reduction-aeration and pyrolysis combined with cold vapour atomic absorption and cold vapour atomic fluorescence are compared for the determination of total mercury in several biological and environmental matrices. The biological samples were digested in a mixture of HNO₃/H₂O₂, the environmental samples in a mixture of HNO₃/HClO₄. After reduction with SnCl₂, the mercury was collected by two-stage gold amalgamation. After microwave digestion reduction-aeration, detection limits of 1.4 ng g⁻¹ and 0.6 ng g⁻¹ were obtained for cold vapour atomic absorption spectrometry (CVAAS) and cold vapour atomic fluorescence spectrometry (CVAFS), respectively, for 250 mg of environmental samples. For biological samples (500 mg) the detection limits were 0.7 ng g⁻¹ (CVAAS) and 0.4 ng g⁻¹ (CVAFS). After pyrolysis, detection limits of 3.5 ng g⁻¹ and 1.6 ng g⁻¹ for CVAAS and CVAFS, respectively, were obtained for a 10 mg sample. Pyrolysis can only be applied when the organic content of the sample is not too high. Accurate results were obtained for 8 certified reference materials of both environmental and biological origin. In addition, a real sludge sample was analysed. Author for correspondence. E-mail: richard.dams@rug.ac.be Received September 18, 2002; accepted December 3, 2002 Published online May 5, 2003     

Selective Solid-Phase Extraction of Trace Copper Ions in Aqueous Solution with a Cu(II)-Imprinted Interpenetrating Polymer Network Gel Prepared by Ionic Imprinted Polymer (IIP) Technique

An Cu(II)-imprinted interpenetrating polymer network (IPN) gel of epoxy-diethylenetriamine and methacrylic acid-acrylamide-N,N′-methylene-bis-(acrylamide) was synthesized by the ionic imprint polymer (IIP) technique. The first polymer network is formed by epoxy gelation with diethylenetriamine. The other is formed by copper methacrylate co- polymerization with acrylamide and cross-linker N,N′-methylene-bis-(acrylamide). The adsorption–desorption characteristics of the IPN gel as a highly selective solid-phase extraction (SPE) and preconcentration adsorbent for Cu²⁺ from aqueous solution were investigated. The experimental results show that trace Cu²⁺ ions can be quantitatively enriched at pH 5 with recovery >95%. The maximum static adsorption capacity of the ion-imprinted functionalized gel adsorbent was 76 mg g⁻¹. Comparing with non-imprinted IPN gel, the imprinted IPN gel has higher adsorption capacity and selectivity for Cu²⁺ by the static adsorption–desorption experiment. Simultaneously, the times of adsorption equilibration and complete desorption were remarkably short. The precision (RSD) for 11 replicate adsorbent extractions of 20 ng mL⁻¹ Cu²⁺ was 3.4%. The established procedure was applied to two real water samples with satisfactory results. The prepared ion-imprinted IPN gel adsorbent was shown to be promising for solid-phase extraction coupled with atomic absorption spectrometry (AAS) for the determination of trace copper in real samples. In addition, the coordination interaction of Cu²⁺ and functional groups of the IPN gel adsorbent was primarily discussed by FT-IR spectra.     

Copper Incorporated [Me2(15)dieneN4] Macrocyclic Complex for Fabrication of PVC based Membrane Electrode for Copper

Copper (II) complex of 2,4-dimethyl-1,5,9,12-tetraazacyclopentadeca-1,4-diene, [Me₂(15)dieneN₄] was synthesized and used in the fabrication of Cu²⁺ – selective ISE membrane in PVC matrix. The membrane having Cu(II) macrocyclic complex as electroactive material along with sodium tetraphenyl borate (NaTPB) as anion discriminator. Dibutyl phthalate (DBP) as plasticizer in poly(vinyl chloride) (PVC) matrix was prepared for the determination of Cu²⁺. The best performance was observed by the membrane having Cu(II) complex–PVC–NaTPB–DBP with composition 1:5:1:3. The sensor worked well over a concentration range 1.12 × 10⁻⁶ M–1.0 × 10⁻¹ M between pH 2.1–6.2 and a fast response time 10±2 s and a lifetime of 6 months. Their performance in partially non-aqueous medium was found satisfactory. Electrodes exhibited excellent selectivity for Cu²⁺ ion over other mono-, di-, trivalent cations. It can also be used as indicator electrode in the potentiometric titration of Cu²⁺ against EDTA as well as in the determination of Cu²⁺ in real samples.