Influence of oxygen plasma treatment on hydrogen chloride removal of activated carbon fibers

The oxygen plasma treatment of activated carbon fibers (ACFs) was carried out to introduce oxygen-containing groups onto carbon surfaces. Surface properties of the ACFs were determined by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). N2/77 K adsorption isotherms were investigated by BET and D-R plot methods to characterize specific surface area, pore volume, and pore size distribution. The efficiency of hydrochloride removal was confirmed by two kinds of methods; one is detecting tubes (range: 1-40 ppm), and the other is a gas chromatography technique. As experimental results, the hydrochloride removal efficiency of the ACFs was increased with the number of plasma treatment times up to around 300%, resulting from newly formed oxygen-containing functional groups (especially phenolic and carboxylic) on carbon surfaces, in the decreased specific surface areas or pore volumes. These results indicate that the plasma treatment leads to the increase of hydrochloride removal due to the improvement of surface functional groups containing oxygen on the carbon surfaces.     

Oxidation behaviors of metallic copper particles in NO reduction mechanism of copper/activated carbons

The reduction of nitric oxide (NO) over Cu/ACFs, prepared by copper electroplating, has been studied. It is found that copper content on the ACFs increases with increasing plating time (up to 45 wt%), while the textural properties including specific surface areas and total pore volumes decrease. As an experimental result, the NO reduction efficiency is increased in all of the Cu/ACFs, and it is confirmed that NO is converted into nitrogen and oxygen on the Cu/ACF surfaces (at 500 degrees C). Especially, the Cu metals on the ACF surfaces scavenge oxygen by oxidizing themselves into Cu2O and finally CuO as a reductant. It is indicated that copper metals on the Cu/ACFs play a major role in the NO removal in this system.     

Ammonia removal of activated carbon fibers produced by oxyfluorination

In this study, activated carbon fibers (ACFs) were produced by an oxyfluorination treatment to enhance the capacity of ammonia gas removal. The introduction of polar groups, such as CF, CO, and COOH, on the ACFs was confirmed by a XPS analysis, and N2/77 K adsorption isotherm characteristics including specific surface area and total and micropore volumes were studied by the BET and t-plot methods. The ammonia-removal efficiency was confirmed by a gas-detecting tube technique. As a result, the specific surface area and micropore volume of ACFs were slightly destroyed as the surface treatment time was increased. However, the oxyfluorinated ACFs led to an increase of fluorine and oxygen-containing polar functional groups in ACF surfaces, resulting in an increase in the ammonia-removal efficiency of the ACFs produced.     

Formaldehyde removal by Rayon-based activated carbon fibers modified by <Emphasis Type="Italic">P</Emphasis>-aminobenzoic acid

We impregnated Rayon-based activated carbon fibers (ACFs) by p-aminobenzoic acid (PABA) and systematically investigated their porous structure, surface chemistry, and formaldehyde removal behavior. Using standard nitrogen adsorption analysis, we found that the specific surface area, the micropore volume, and the total pore volume decreased with increasing concentration of PABA. Through elemental analysis and X-ray photoelectron spectroscopy, it was found that some nitrogen-containing functional groups presented on the surface of modified Rayon ACFs. The modified Rayon-based ACFs showed much higher adsorption capacity and longer breakthrough time for formaldehyde than did as-prepared Rayon-based ACF. We proposed that the improvement of formaldehyde removal by modified ACFs was attributed to the combined effects of physisorption contributed by pore structures and chemisorption contributed by the N-containing functional groups, whereas there was only physisorption between the as-prepared ACF and formaldehyde molecules.     

Start-up of Completely Autotrophic Nitrogen Removal Over Nitrite Enhanced by Hydrophilic-Modified Carbon Fiber

In order to assess the effects of the surface hydrophilicity of supports on the biofilm formation and evaluate the performance of completely autotrophic nitrogen removal over nitrite (CANON) process in a sequencing batch biofilm reactor (SBBR), unmodified activity carbon fibers (ACFs) and ACFs hydrophilic modified by heat treatment were used as supports. CANON process was initiated in a SBBR from conventional activated sludge. An operation temperature of 32 ± 2 °C, dissolved oxygen (DO) level at 1.5 mg L⁻¹ and free ammonia (FA) concentration with 3.98–15.93 mg L⁻¹ were maintained in the SBBR. Fourier transform infrared (FT-IR) spectra and Boehm’s neutralizing titration exhibited that modified ACFs had more oxygen-containing groups than unmodified ACFs. Larger biofilm growth on the modified surfaces examined by scanning electron microscopy and biofilm’s total dry weight, and the biofilm on the modified surfaces were more active, compared with those on the unmodified surfaces. This study demonstrates the hydrophilic-modified ACFs have better biological affinity than unmodified ACFs. Maximal total nitrogen removal rate of 0.088 k g N m⁻³ day⁻¹ was achieved for the CANON process on day 80, indicating the CANON process was successfully started up. Apart from supports, the strategies of DO supplying and controlling FA concentration were also keys in starting up the CANON process within a shorter period.     

Effect of acidic treatment on metal adsorptions of pitch-based activated carbon fibers

In this work, the pitch-based activated carbon fibers (ACFs) were prepared by nitric acid to investigate the multi-metal adsorption in interfacial and textural points of view. N2/77 K adsorption isotherm characteristics, including the specific surface area and micropore volume, were studied by BET specific surface area and t-plot methods, respectively. As a result, the specific surface area of the almost neutral ACFs in nature significantly decreased with nitric acid treatment, probably due to the widening of micropores. However the total acidity, including the carboxyl groups, on carbon surfaces was extremely induced during the acidic surface treatment. From the adsorptions of Cu2+ and Ni2+, it was revealed that the adsorption capacity of metal ions was mainly influenced by the weakly acidic functional groups such as lactones on the carbon surfaces at pH < pI (isoelectric point), and by the strongly acidic functional groups such as carboxyl groups at pH > pI.     

Antibacterial behavior of transition-metals-decorated activated carbon fibers

The antibacterial behavior of transition metals (Cu or Ag)-plated activated carbon fibers (ACFs) was investigated. The pore structure of the ACFs before and after metal electroplating was studied by N(2)/77 K isothermal adsorption. The antibacterial behavior against Staphylococcus aureus and Klebsiella pneumoniae was tested by a modified dilution method. As experimental results, the ACFs showed a decrease in specific surface area and micro- and total pore volume with increasing metal content. The antibacterial behavior of the ACFs was predominantly increased and showed over 99% against S. aureus as well as K. pneumoniae, attributed to the presence of metal nanoparticles in this system.     

Adsorption of phenol on supercritically activated carbon fibres: effect of texture and surface chemistry

The influence of texture and surface chemistry on the phenol adsorption capacity of activated carbon fibres (ACFs) was studied. ACFs were prepared by carbonization of a phenolic textile fibre under nitrogen flow, followed by activation with H(2)O and CO(2) (under atmospheric pressure and supercritical state). The materials were characterised by N(2) and CO(2) adsorption, and by temperature programmed desorption studies. A strong correlation between the amount of adsorbed phenol and the micropore volume has been observed. The relationship between surface oxygen concentration and amount of physisorbed and chemisorbed phenol was assessed, and it was shown that higher amounts of surface oxygen groups decreased the phenol chemisorption capacity of ACFs.     

Influence of anodic treatment on heavy metal ion removal by activated carbon fibers

In this work, the effect of electrochemical oxidation treatment on activated carbon fibers (ACFs) was studied in the context of Cr(VI), Cu(II), and Ni(II) adsorption behavior. Ten weight percent phosphoric acid (A-ACFs) and ammonia (B-ACFs) were used for acidic and basic electrolytes, respectively. Surface properties of ACFs were determined by X-ray photoelectron spectroscopy (XPS). The specific surface area and the pore structure were evaluated from nitrogen adsorption data at 77 K. As a result, the electrochemical oxidation treatment led to an increase in the amount of oxygen-containing functional groups. Also, the adsorption capacity of the electrochemically oxidized ACFs was improved in the order B-ACFs > A-ACFs > untreated-ACFs, in spite of a decrease in specific surface area which resulted from pore blocking by functional groups and pore destruction by acidic electrolyte. It was clearly found that the heavy metal ions were largely influenced by the functional groups on the ACF surfaces.     

Grafting of poly(methyl vinyl ketone) onto aluminum surface

Polymers were grafted on aluminum surfaces in order to modify the chemical and physical properties of the interface. The properly cleaned and activated surface of the aluminum substrate was first "silanized" either with 3-(trimethoxysilyl)propylamine or allyltrimethoxysilane. The grafting was carried out following two methods: (i) by the reaction of preformed poly(methyl vinyl ketone) with the aminosilane-modified surface; and (ii) by polymerization of methyl vinyl ketone with the vinylsilane-modified surface. The modified aluminum surfaces were characterized by X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, and energy dispersive X-ray spectroscopy. The new surfaces were examined by contact-angle measurements, and determinations of the Lewis basicity.     

Changes in lipid composition of apple surface layer during long-term storage in controlled atmosphere

Apples are the most frequently consumed fruit and about 90 % of apple production is stored. Fatty acids and lipids are important constituents of plant cells. Disturbances in the lipid composition of fruit may lead to various stress processes, resulting in some storage disorders. This work is focused on an analysis of surface lipids of different varieties of apples stored in a normal atmosphere and a modified atmosphere with ultra-low oxygen content, for 4 months and 6 months. The major fatty acids in apple surface layers are palmitic acid, stearic acid, linoleic acid, and oleic acid. During the 6-months storage period, a variety-specific decrease in the total fatty acids content and an increase in saturation degree was observed in all the varieties tested, when compared with the 4-months storage. The greatest differences in saturation degree were observed in the Golden Delicious variety, in which the highest content of unsaturated fatty acids was also found. Microbial contamination of apple surfaces increased gradually over the storage process. Higher fungi levels were found in apples stored in the regular atmosphere than in the modified atmosphere, which can be attributed to changes observed in the total lipid content and saturation degree of the surface fatty acids and also to the sensitivity of microorganisms to the oxygen content in the storage room.     

Modification of fumed silica surface with different sulfonamides via a postsynthesis method and their application as antibacterial agents

The surface of nanosized fumed silica (FSi) was modified with different amine groups by the use of silylating agents. The obtained propylamine, propylpiperazine, and propyl-p-phenylenediamine–modified FSi were treated with different sulfonyl chlorides to gain sulfonamide-modified FSi compounds. These compounds were characterized by various techniques including Fourier transform infrared spectroscopy, thermogravimetric analysis, differential thermal analysis, scanning electron microscopy, and energy-dispersive X-ray spectroscopy (EDX), confirming the grafted sulfonamides on the FSi surface. Sulfonamide-modified surfaces are efficient catalysts for the Michael addition-based syntheses and coupling reactions. Furthermore, the antibacterial tests showed that these modified FSi compounds have antibacterial activities and thus are useful materials for preparing antibacterial silicone-based compounds such as silicone glue and oil.     

NO removal of Ni-electroplated activated carbon fibers

In this study, activated carbon fibers (ACFs) were treated by a Ni-electroplating technique in order to remove nitric oxide (NO). The surface properties of the ACFs were investigated by XPS measurement. N2/77 K adsorption isotherm characteristics were determined by the BET equation. Also, NO-removal efficiency was confirmed by gas chromatography. For experimental results, Ni2p was introduced on ACFs during the Ni-electroplating technique. The nickel deposited on ACFs appeared to increase the NO removal despite the decrease in the BET specific surface areas and micropore volumes compared to nontreated ACFs. Consequently, it was found that NO conversion of ACFs was significantly improved due to the catalytic reaction of nickel deposited on ACFs.     

Low Temperature Catalytic Hydrolysis of Carbon Disulfide on Activated Carbon Fibers Modified by Non-thermal Plasma

In order to improve the carbon disulfide (CS₂) catalytic hydrolysis efficiency of activated carbon fibers (ACFs), ACFs surface was modified by non-thermal plasma (NTP). In particular, the effects of modification conditions on the catalyst properties were studied, including the reactor structure, modification atmosphere, modification time, output voltage and discharge gap. The catalytic activity study showed that ACFs with NTP modification enhanced CS₂ catalytic hydrolysis. The optimal reactor structure, modification atmosphere, modification time, output voltage and discharge gap was a coaxial cylinder, an N₂ atmosphere, 5 min, 7 kV and 7.5 mm, respectively. The effect of the NTP modification on the micro-structural properties of the ACFs was characterized using scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET) and X-ray photoelectron spectroscopy (XPS) methods. The results showed that NTP modification improved the dispersion of functional groups and increased the number of oxygen-containing and nitrogen-containing functional groups, thus the catalytic activity could be enhanced. The present results indicated that NTP modification was an effective way to manipulate ACFs surface properties for the CS₂ catalytic hydrolysis reaction.     

Surface modification of polymers. II. Grafting with glycidyl acrylates and the reactions of the grafted surfaces with amines

The surface of low density polyethylene has been grafted with glycidyl acrylate and glycidyl methacrylate by photoinitiation. ESCA measurements on the grafted surface showed a 72% coverage for glycidyl acrylate and 52% for glycidyl methacrylate after 10 min of grafting with UV irradiation. ATR–IR showed a 10 times more extensive grafting for glycidyl acrylate than for glycidyl methacrylate after 10 min of grafting, indicating reaction to deeper layers. Acetone and ethanol were used as solvents: acetone yielded slightly more grafting at the surface. The grafted surfaces were reacted with 2M solutions of aniline and propylamine in ethanol. After 4 h reaction at 60°C, with aniline 52% of the epoxy groups while for propylamine 96% of the groups were consumed, as measured with ATR–IR.     

Studies on pore structures and surface functional groups of pitch-based activated carbon fibers

The present study concerns the physical activation and chemical oxidation of pitch-based activated carbon fibers (ACFs) as ways to improve the adsorption properties. The surface oxides of the ACFs studied were determined by Boehm's titration and the pore structures were studied by the BET method with N(2)/77 K adsorption. Also, the adsorption properties of the ACFs were investigated with chromium ion adsorption by different adsorption models. As a result, it was observed that carboxyl groups were largely created after nitric acid treatment on ACFs. The affinity for chromium ions increases with increasing specific surface area, micropore volume, and surface functionalities of ACFs as the activation time increases.     

Microstructure and surface properties of fibrous and ground cellulosic substrates

Cotton and linen fibers were ground in a ball-mill, and the effect of grinding on the microstructure and surface properties of the fibers was determined by combining a couple of simple tests with powerful techniques of surface and structure analysis. Results clearly proved that the effect of grinding on cotton fiber was much less severe than on linen. For both fibers, the degree of polymerization reduced (by 14.5% and 30.5% for cotton and linen, respectively) with a simultaneous increase in copper number. The increased water sorption capacity of the ground substrates was in good agreement with the X-ray results, which proved a less perfect crystalline structure in the ground samples. Data from XPS and SEM-EDS methods revealed that the concentration of oxygen atoms (bonded especially in acetal and/or carbonyl groups) on the ground surfaces increased significantly, resulting in an increase in oxygen/carbon atomic ratio (XPS data: from 0.11 to 0.14 and from 0.16 to 0.29 for cotton and linen, respectively). Although grinding created new surfaces rich in O atoms, the probable higher energy of the surface could not be measured by IGC, most likely due to the limited adsorption of the n-alkane probes on the less perfect crystalline surfaces.     

Activated carbon fibers with a high heteroatom content by chemical activation of PBO with phosphoric acid

The preparation of activated carbon fibers (ACFs) by phosphoric acid activation of poly(p-phenylene benzobisoxazole) (PBO) fibers was studied, with particular attention to the effects of impregnation ratio and carbonization temperature on porous texture. Phosphoric acid has a strong effect on PBO degradation, lowering the temperature range at which the decomposition takes place and changing the number of mass loss steps. Chemical analysis results indicated that activation with phosphoric acid increases the concentration of oxygenated surface groups; the resulting materials also exhibiting high nitrogen content. ACFs are obtained with extremely high yields; they have well-developed porosity restricted to the micropore and narrow mesopore range and with a significant concentration of phosphorus incorporated homogeneously in the form of functional groups. An increase in the impregnation ratio leads to increases in both pore volume and pore size, maximum values of surface area (1250 m(2)/g) and total pore volume (0.67 cm(3)/g) being attained at the highest impregnation ratio (210 wt % H(3)PO(4)) and lowest activation temperature (650 °C) used; the corresponding yield was as large as 83 wt %. The obtained surface areas and pore volumes were higher than those achieved in previous works by physical activation with CO(2) of PBO chars.     

Surface characterization of argon-plasma-modified perfluorosulfonic acid membranes

The perfluorosulfonic acid membranes which are used in direct methanol fuel cells were modified with argon plasma under various conditions, and the physicochemical and transport properties of the resulting membranes were investigated using various analytical techniques. The plasma treatment was found to change the surface morphology and physicochemical properties of the membranes. The surface roughness of the membranes was increased by the etching effect of plasma. From the FTIR and XPS analyses, the incorporation of new oxygen functionalities, such as the peroxide group, was confirmed. The breakage of both the sulfonic acid groups and ether linkages were also found to cause an increase in the equivalent weight of the modified skin layer of the membrane. The incident water contact angle of the modified membrane in a dry state decreased with an increased plasma treatment, because of the hydrophilic groups that developed on the membrane surface. The time-dependent water contact angle, however, increased in proportion to the extent of the plasma treatment, due to the reduced concentration of sulfonic acid groups. Although the equilibrium water uptake of the modified membrane was almost invariable because of the negligible thickness of the modified skin layer, the transport properties of the membrane such as methanol permeability and proton conductivity were significantly reduced.     

Electrocatalytic Reduction of Oxygen at Glassy Carbon Electrodes Coated with Diazonium‐derived Porphyrin/Metalloporphyrin Films

In this study, the influence of the film structure was investigated on the electrocatalytic oxygen reduction at GC electrodes covered with porphyrin and metalloporphyrin rings via the diazonium modification method. For that purpose, primarily, tetraphenylporphyrin (TPP) films on GC electrode surfaces were prepared by electroreduction of in situ generated diazonium salts of 5‐(4‐aminophenyl)‐10,15,20‐triphenylporphyrin (APP) and 5,10,15,20‐tetrakis(4‐aminophenyl)porphyrin (TAPP) molecules. Next, the formation of metalloporphyrin films on the modified surfaces was accomplished through the complexation reactions of surface porphyrin rings with metal ions in the salt solutions containing Mn(II), Fe(III) and Co(II) ions. The resulting porphyrin and metalloporphyrin layers were identified with XPS and ICP‐MS. The electrochemical barrier properties of the films on GC surfaces were examined by cyclic voltammetry in K₃Fe(CN)₆ aqueous solution. The electrocatalytic abilities of the resulting films were also investigated for the oxygen electrochemical reduction by employing cyclic voltammetry in PBS solutions saturated with oxygen. The results showed that the oxygen reduction potentials on modified GC electrodes were shifted to less negative potentials compared to that of bare GC electrode. Also, it was obtained that the oxygen reduction reaction was more effective on the GC electrodes modified with TPP rings by using TAPP molecules than those prepared by using APP molecules.