Phase titration with clarification end-point

An improved method of phase titration has been developed for the analysis of binary or pseudo-binary systems. A clarification end-point is used in place of the usual cloud end-point. Advantages are that end-points are equally sharp over a wide sample composition range, the titration volume is a very nearly linear function of composition so that often only one calibration point is needed, and the technique can be extended to cover the entire binary composition range.     

Selective Liquid and (Vinyl-Chloride) Pentoxyverine Membrane Electrodes - Their Preparation and Use for the Potentiometric Determination of Pentoxyverine Citrate

Abstract

The use of liquid and poly(vinyl-chloride) membrane electrodes which are sensitive and reasonably selective for pentoxyverine determination is described here. The electrodes are based on the use of pentoxyverine-picrate, pentoxyverine-picrolonate and pentoxyverine-tetraphenylborate ion association complexes as electroactive materials in nitrobenzene or in poly(vinyl chloride) matrix. These electrodes show near Nernstian response values in different concentration ranges, depending on the nature of the used counter-ions, at 3.3–7.8 pH range. Potentiometric determination of pentoxyverine citrate with use of these electrodes gives good results which later on are compared with those obtained by non-aqueous titration.     

Back titration with mercuric nitrate in alkaline : medium volumetric analysis of binary mixtures of the alkaline earths,magnesium, zinc and cadmium

Mercuric nitiate has proved to be suitable for the back titration of the excess amount of EDTA remaining in solution when this compound has reacted quantitatively either with zinc or cadmium in the presence of one of the three elements barium, strontium and magnesium at pH 8 or 9, or with both cations at pH 11. Advantage is taken of this behaviour for analysing binary mixtures of the above mentioned cations by back titration at lower and higher pH's The end-points are detected potentiometrically, reasonable jumps being obtained; the agreement with the theoretical end-points is satisfactory.     

Preferential solubilization of dodecanol from dodecanol-limonene binary oil mixture in sodium dihexyl sulfosuccinate microemulsions: effect on optimum salinity and oil solubilization capacity

Solubilization of dodecanol-limonene binary oil mixtures has been studied in saturated Winsor type I and III sodium dihexyl sulfosuccinate microemulsions. The systems showed different oil solubilization behavior below and above dodecanol volume fraction 0.2. Below 0.2 dodecanol volume fraction regular Winsor type microemulsions formed. The oil solubilization was characterized in this concentration range by the optimum salinity and the maximum characteristic length. Dodecanol showed Langmuirian-type surface excess adsorption at the vicinity of the surfactant layer. Variation of the optimum salinity and middle phase characteristic length with increasing dodecanol concentration could be linked to changes in the dodecanol surface excess. These relationships were used to develop new mathematical models for the optimum salinity and characteristic length as a function of oil phase composition. Both models yield excellent agreement with the data. Above dodecanol volume fraction 0.2 regular Winsor type III microemulsions are not formed. Therefore our new models are not applicable in this concentration range.     

Selective potentiometric determination of Bi(III) with a coated-wire electrode

A bismuth-selective electrode based on the chlorobismuthate(III) salt of Aliquat 336 is described. The electrode gives nearly linear response in the bismuth concentration range 10⁻¹–10⁻⁴M. The optimum solution conditions for operation of the electrode have been determined together with possible interference effects. The application of the electrode to analysis of samples containing large amounts of other metals is illustrated by the determination of bismuth in pharmaceuticals. The electrode is shown to give results by direct potentiometry and the standard-addition method which differ from atomic-absorption results by not more than 2%.     

The heterometric microdetermination of mercury of mercaptobenzthiazole

The heterometric determinations of murcury or mercaptobentlnazole are very sensitive reactions. An aqueous or a dilute alcoholic solution is used and the titration may lie carried out at pH 2–10. If meicaptobenzlhiazole is determined, two analytical end-points are obtained : the first gives an estimate, the second gives the precise end-point. In all cases, the insoluble Hg(MBT)₂ is obtained, The presence of larger amounts of strong acids is disadvantageous Large amounts of acetic acid cause distuibances in aqueous solution; dilute alcoholic .solution is therefore used The theoretical end-point is obtained by the intersection of two lines. In acid solution a horizontal maximum density line is obtained at the end ot the reaction, in alkahne solution a maximum point is obtained instead. 1–2 mg mercury or meicaptobenzthiazole may be determined in 20–30 ml solution with an error of 0–3% 'Ihe titration time is 10–20 mniutes     

The influence of diluter system on polymer-stabilised blue-phase liquid crystals

In the present work, diluter effects on the phase transition temperatures and electro-optical properties of the polymer-stabilised blue-phase liquid crystals with microsecond respond time have been carried out. The temperature range of polymer-stabilised blue-phase samples broadened over 50 K including room temperature. By increasing the concentration of diluter, the faster response time is obtained, but Kerr constant become smaller. These values are still two orders of magnitude larger than conventional Kerr materials such as nitrobenzene. The major bottleneck is the increased operating voltage. Hysteresis is sensitive to the diluter concentration and is slightly small for polymer network systems. For next-generation display technology, an optimal concentration of diluter plays a crucial role to a proper balance between response time and operation voltage.     

Dynamics and mechanism of bridge-dependent charge separation in pyrenylurea-nitrobenzene pi-stacked protophanes

Herein are reported the synthesis, structure, and electronic properties of a series of tertiary di- and polyarylureas possessing pyrene and nitrobenzene end groups separated by a variable number of internal phenylenediamine bridging groups. These molecules adopt folded "protophane" structures in which the adjacent arenes are loosely pi-stacked. The behavior of both the pyrene and nitrobenzene singlet states has been investigated by means of femtosecond broadband pump-probe spectroscopy, and the transients have been assigned on the basis of comparison to reference molecules. Femtosecond time resolution permits direct observation of the fast internal conversion process for both the pyrene and nitrobenzene upper singlet states, as well as the intersystem crossing of nitrobenzene. The ultrafast (ca. 100 fs) charge separation of the donor-acceptor urea having no bridging group is attributed to an internal conversion process. The slower charge separation and charge recombination of the donor-acceptor urea having a single bridging group occur via a bridge-mediated superexchange process. Addition of a second bridging unit results in a role reversal for the pyrene singlet state, which now serves as an excited-state acceptor with the bridging units serving as the electron donors. The change in the directionality of electron transfer upon addition of a second bridging phenylenediamine is a consequence of a decrease in the bridge oxidation potential as well as a decrease in the rate constant for single-step superexchange electron transfer.     

Catalytic end-point detection in titrimetric analysis

In catalytic end-point detection, the first drop of titrant in excess is not used for a stoichiometric reaction with the indicator (as in conventional titrations) but acts as, or liberates, a catalyst for the indicator reaction. A very small excess of titrant thus suffices to catalyze large amounts of the indicator reaction mixture. Such catalytic end-points are therefore very sensitive. Terminology is discussed briefly. The various types of titration (direct, with a “brake”, reversed, indirect and substitution) and of end-point detection (visual, olfactory, photometric, thermometric and electrometric) are described. Applications of these techniques are summarized.     

The platinum-20% rhodium electrode in potentiometry

The performance of a platinum-20% rhodium alloy indicator electrode is studied in a number of potentiometric redox and acid-base titrations and compared with that of the conventional platinum electrode. The potential breaks obtained with the alloy electrode are always smaller than those obtained with the platinum electrode. The end-points are also usually indicated later than the true end-points. The bimetallic electrode system comprising platinum and platinum-rhodium electrodes gives a peak at the correct end-point even with 0.001N concentration titrations, where the ordinary potentiometric systems do not always give good results.     

Excess Molar Volumes and Partial Molar Volumes of Binary Mixtures Containing Diethylcarbonate with Benzene and Substituted Benzenes at 293.15 K

Densities of the binary mixtures of diethylcarbonate with benzene and substituted benzenes, namely toluene, bromobenzene, chlorobenzene and nitrobenzene have been measured as a function of the composition, at 293.15 K and atmospheric pressure using a bicapillary pycnometer with an accuracy of 4 parts in 10⁴.The calculated excess molar volumes, V ^E were correlated with Redlich-Kister equation. The excess molar volumes are negative over the entire range of composition for the systems diethylcarbonate with benzene, toluene, bromobenzene and nitrobenzene. An inversion of the sign of V ^E is observed over some concentration for mixtures of diethylcarbonate with chlorobenzene. Partial molar volumes, V_i are also evaluated and their values have been extrapolated to zero concentration to obtain the limiting value at infinite dilution, V^o _i . The numerical values of the excess molar volumes for binary mixtures decrease in the order: chlorobenzene > benzene > bromobenzene ≈ toluene > nitrobenzene. The results are explained in terms of dissociation of the self-associated solute molecules and the formation of aggregates between unlike molecules.     

Liquid-liquid extraction of some lanthanide metal ions by polyoxyalkylene systems

Polyoxyalkylene systems, namely, polypropylene glycol (PPG-1025), polyethylene glycol (PEG-600) and polybutadieneoxide (PBDO-700) dissolved in either nitrobenzene or 1,2-dichloroethane have been tested as prospective extractants for some lanthanide metal ions (Eu(3+), Pr(3+) and Er(3+)) from their aqueous solutions in the presence of picrate anions. The metal ions were quantified before and after extraction using the inductively coupled plasma emission spectrophotometry technique. The percent extraction and the distribution coefficients have indicated that pH of the aqueous phase, picrate concentration and the organic solvent are the major parameters that affect the extraction efficiency of the metal ions. The optimum pH range was found to be 3.5-5.5 and the picrate concentration should be as high as possible; however, a picrate concentration of about 0.05 M proved to be adequate for a near quantitative extraction. In all cases, nitrobenzene enhanced a higher percent extraction compared to 1,2-dichloroethane. The efficiency of the polyoxyalkylene systems to extract certain lanthanide metal ions was in the order PBDO-700>PPG-1025>PEG-600 when nitrobenzene was the organic solvent and in the order PPG-1025>PBDO-700 approximately PEG-600 when 1,2-dichloroethane used as the solvent in the organic phase. The extractability of PPG-1025 towards the lanthanide metal ions was in the order Pr(3+)>Eu(3+)>Er(3+) irrespective of the organic solvent used. The stoichiometry of the extracted polyoxyalkylene ion-pairs with the lanthanide metal ions has been estimated. Each mole of metal ions is associated with three moles of picrate anions and 13 to 14 moles of propyleneoxide units in the case of PPG-1025, and about 9 to 10 moles of ethyleneoxide units in the case of PEG-600 and 10 moles of butadieneoxide units in the case of PBDO-700.     

Quasichemical interpretation of the ultrasonic velocity in ternary aqueous systems

The quasichemical model of hydration have been used to calculate the speed of ultrasound in binary solutions of water and nonelectrolyte. The model has been confined to systems that exhibit a maximum in the ultrasonic velocity vs. nonelectrolyte concentration. The parameters of the model are the hydration equilibrium constant, the nonelectrolyte hydration number, and the molar volume and compressibility of the hydrated nonelectrolyte. These have been fitted to experimental results by the method of least squares. The model calculations reproduce qualitatively the ultrasonic velocity as a function of nonelectrolyte concentration. The calculated maximum of the ultrasonic velocity is generally too low, but the nonelectrolyte concentration at which this maximum occurs agrees well with experiment.Addition of a third component shift the velocity maximum. The quasichemical model has also been used to calculate this shift. These calculations have been based on the parameters developed for the binary system. The shift on the nonelectrolyte concentration scale is reproduced satisfactorily, but the shift of the maximal value of the ultrasonic velocity is less accurately predicted by the model.     

Optimization of a multisolvent composition in RP-HPLC: Convenient criterion for preliminary search for the best eluent strength

Summary Interpretive methods are very commonly used to direct the search for the optimum solvent composition. For multisolvent systems, the composition search space is often reduced to one straight line (ternary systems with two organic modifiers), three straight lines (three ternary systems with each possible pair of the organic modifiers of the tetrahedron) — or a plane delimited by a triangle (quaternary systems inside the solvent tetrahedron). In each case, the space is restricted by binary compositions of equal solvent strength, in such a way that through it, the analysis time remains approximately constant. This restricted space is defined without taking into account any selectivity criterion between peaks, and consequently, if a given pair of peaks is badly resolved with the considered binary solvents, the probability of any mixture of them improving the peak selectivity will be very low. The ability to calculate the retention models in a binary solvent system from two linear gradient runs, allows the prediction of the selectivity for each pair of solutes into each binary solvent system (ACN/Water, MeOH/Water, THF/Water) from six preliminary linear gradient runs, and then, to determine and eliminate all the sets of isoeluotropic binary compositions that will offer little hope of giving useful separation conditions with multisolvent systems and, at the same time, to select the most promising set of binary compositions. The selectivity and the total time of the chromatogram are the two parameters that are considered for this search. When several possiblities are found, priority is given to the simplest solvent system (binary rather than ternary and ternary rather than quaternary). Reducing the number of preliminary experiments and improving the accuracy of the predicted optimum are the two objectives of this approach. Its practical interest is discussed by comparing the results obtained for an illustrative separation to those obtained with another existing method.     

Bioethanol Production Optimization: A Thermodynamic Analysis

In this work, the phase equilibrium of binary mixtures for bioethanol production by continuous extractive process was studied. The process is composed of four interlinked units: fermentor, centrifuge, cell treatment unit, and flash vessel (ethanol-congener separation unit). A proposal for modeling the vapor–liquid equilibrium in binary mixtures found in the flash vessel has been considered. This approach uses the Predictive Soave–Redlich–Kwong equation of state, with original and modified molecular parameters. The congeners considered were acetic acid, acetaldehyde, furfural, methanol, and 1-pentanol. The results show that the introduction of new molecular parameters r and q in the UNIFAC model gives more accurate predictions for the concentration of the congener in the gas phase for binary and ternary systems.     

Indirect spectrophotometric determination of chloride by solvent extraction as tris(1,10-phenanthroline)iron(II) thiocyanate

An indirect spectrophotometric method for the determination of small amounts of chloride in fresh waters is described. Chloride ions react with mercury(II) thiocyanate to liberate thiocyanate ions, which can be selectively extracted into nitrobenzene with tris(1,10-phenanthroline)iron(II) chelate cations. The red color (516 nm) of the organic phase measured against a reagent blank is proportional to the initial concentration of chloride ions in the aqueous phase. At least an equimolar amount of tris(1,10-phenanthroline)iron(II) chelate and a 3-fold amount of mercury(II) thiocyanate are needed; the optimal pH range is 1.5–3.5. Beer's law is obeyed over the concentration range of 0.8–5.6 10^-5 M of chloride. The color stability and the apparent sensitivity are better than those of the mercury(II) thiocyanate-iron(III) method. Large amounts of sulphate, phosphate, fluoride, carbonate, acetate, potassium, sodium, and ammonium ions had negligible or no effect ; bromide, iodide, cyanide, sulphide, and thiocyanate interfere.     

Mixing behavior of binary insoluble phospholipid monolayers. Analysis of the mixing properties of binary lecithin and cephalin systems by application of several surface and spreading techniques

The detailed miscibility analysis of binary phospholipid monolayers requires the application of a variety of spreading and surface techniques which often yield complementary results. Testing the equilibrium state of the binary monolayer by long-time experiments is also of great importance. Studies of the compression and spreading behavior of binary monomolecular systems form a basis for the determination of binary monomolecular phase diagrams. Within these plots different phase regions occur which permit clear statements regarding the miscibility state. Additional knowledge of the miscibility properties (phase diagrams) of the binary bulk systems is required. From the analogy of the properties of the bulk systems, the miscibility state of the monolayers is also determined by the temperature, and we can classify the monolayers of binary lecithin and cephalin systems into systems of complete miscibility, partial miscibility and complete immiscibility. In addition to the differences in the chemical structure of the mixing components, the film states in the monolayer and the miscibility behavior of the bulk systems are also influencing factors. If one of the components does not produce a spreading pressure, miscibility gaps occur in the phase diagram of the phospholipid monolayer. The miscibility gap, expressed by a constant spreading pressure, indicates complete immiscibility within this concentration range. If both components produce spreading pressures, and condensed and liquid-expanded film states within the considered temperature range, partial miscibility of the components becomes probable. The most effective parameter is then the difference in the chemical structure of the components. When both components produce spreading pressures and condensed films, the chemical structure of the mixing phospholipid compounds within their hydrophilic and hydrophobic parts is of essential importance. Depending on the differences in the chemical structures of their chains and their head groups in the case of binary phospholipid monolayers, the following possibilities result: complete miscibility, partial miscibility and complete immiscibility of the lecithins and the cephalins. Complete miscibility within the binary phospholipid monolayer takes place in the case of identical head-group structure and where there are only small differences in the chain length of the fatty acid groups. With increasing hydrocarbon chain length differences, partial miscibility or even complete immiscibility can occur within the monolayer. Chemical differences in the head-group structure of the mixing components have a similar influence. In the case of binary lecithin/cephalin mixtures, the differences in the head-group structure affect the miscibility behavior more than the chain length differences do in the case of lecithin/lecithin and cephalin/cephalin mixtures.(ABSTRACT TRUNCATED AT 400 WORDS)     

Micellar behavior of tetradecyldimethylbenzylammonium chloride in water-alcohol mixtures

The effect of butanol and benzyl alcohol on the critical micelle concentration and the degree of ionization of micelles of tetradecyldimethylbenzylammonium chloride has been studied conductometrically in the temperature range of 5 to 40 degrees C at 5 degrees C intervals. The results indicate that some self-association process of benzyl alcohol in the aqueous phase commences when its concentration amounts to ca 0.05 m. By applying the theoretical treatment suggested by Motomura for binary surfactant systems, the molar fraction of alcohol in the micelle and the standard free energy of solubilization were estimated from the dependence of cmc on temperature and alcohol concentration. For comparative purposes the micellar properties of tetradecyltrimethylammonium bromide in water-alcohol systems at 25 degrees C have also been studied.     

关于一元酸准确滴定判据的商榷

化学分析教科书中给出的弱酸能被准确滴定的条件是cKa≥1.0×10-8。本文根据这一判据的来源(滴定突跃≥0.3pH单位),对一元酸体系的滴定情况进行了严格数学处理。计算结果表明,只有同时满足弱酸的浓度c1.0×10-3mol/L和cKa≥1.0×10-8条件下,弱酸才能被准确滴定。对于浓度极稀的酸溶液(c≤1.4×10-4mol/L),无论强酸还是弱酸都不能被准确滴定。对教材很少涉及的不同浓度酸碱互相滴定的情况也给出了有价值的结论。