2‐[(Diphenylphosphino)methyl]pyridine as ligand for iron‐based atom transfer radical polymerization

2‐[(Diphenylphosphino)methyl]pyridine (DPPMP) was successfully used as a bidentate ligand in the iron‐mediated atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) with various initiators and solvents. The effect of the catalytic system on ATRP was studied systematically. Most of the polymerizations with DPPMP ligand were well controlled with a linear increase in the number‐average molecular weights (M_n) versus conversion and relatively low molecular weight distributions (M_w/M_n = 1.10–1.3) being observed throughout the reactions, and the measured molecular weights matched the predicted values. Initially added iron(III) bromide improved the controllability of the polymerization reactions in terms of molecular weight control. The ratio of ligand to metal influenced the controllability of ATRP system, and the optimum ratio was found to be 2:1. It was shown that ATRP of MMA with FeX₂/DPPMP catalytic system (X = Cl, Br) initiated by 2‐bromopropionitrile (BPN) was controlled more effectively in toluene than in polar solvents. The rate of polymerization increased with increasing the polymerization temperature and the apparent activation energy was calculated to be 56.7 KJ mol^?1. In addition, reverse ATRP of MMA was able to be successfully carried out using AIBN in toluene at 80 °C. Polymerization of styrene (St) was found to be controlled well by using the PEBr/FeBr₂/DPPMP system in DMF at 110 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2922–2935, 2008     

ATRP of styrene catalyzed by elemental Fe(0) and Br2: An easy and economical ATRP process

In this work, zero‐valent iron (Fe(0)) (powder or wire) and elemental bromine (Br₂) were used as the catalysts for atom transfer radical polymerization (ATRP) of styrene (St) without any additional initiator at 110 °C. The polymerizations happened with controlled evidence at appropriate molar ratio of Fe(0) to Br₂: a remarkable increase of molecular weights with St conversions, the narrow molecular weight distributions and living polymer chains end‐capped by Br. More Br₂ or less Fe(0) led to a slow polymerization rate but an improved control over molecular weights. After examining the polymer chain ends by matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, it was concluded that the polymerization was initiated by thermal self‐initiation, and regulated by the in situ generated Fe^IIIBr₃. The results suggested that the Fe(0)/Br₂ catalyzing polymerization was a classical ATRP process with easier operation and more economical components. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characterization of well‐defined ABC‐type triblock copolymers via atom transfer radical polymerization and stable free‐radical polymerization

An asymmetric difunctional initiator 2‐phenyl‐2‐[(2,2,6,6 tetramethylpiperidino)oxy] ethyl 2‐bromo propanoate ( 1 ) was used for the synthesis of ABC‐type methyl methacrylate (MMA)‐tert‐butylacrylate (tBA)‐styrene (St) triblock copolymers via a combination of atom transfer radical polymerization (ATRP) and stable free‐radical polymerization (SFRP). The ATRP‐ATRP‐SFRP or SFRP‐ATRP‐ATRP route led to ABC‐type triblock copolymers with controlled molecular weight and moderate polydispersity (M_w/M_n < 1.35). The block copolymers were characterized by gel permeation chromatography and ¹H NMR. The retaining chain‐end functionality and the applying halide exchange afforded high blocking efficiency as well as maintained control over entire routes. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2025–2032, 2002     

Synthesis and characterization of multifunctional polymers via atom transfer radical polymerization of N‐(ω′‐alkylcarbazolyl) methacrylates initiated by Ru(II) polypyridyl chromophores

A series of poly(N‐(ω′‐alkylcarbazoly) methacrylates) tris(bipyridine) Ru‐centered bifunctional polymers with good filming, thermal, and solubility properties were synthesized and characterized. Atom transfer radical polymerization (ATRP) of N‐(ω′‐alkylcarbazoly) methacrylates in solution was used, where Ru complexes with one and three initiating sites acted as metalloinitiators with NiBr₂(PPh₃)₂ as a catalyst. ATRP reaction conditions with respect to polymer molecular weights and polydispersity indices (PDI) of the target bifunctional polymers were examined. Electronic absorption and emission spectra of the resultant functional polymers provided evidence of chromophore presence within a single polymeric chain. The thermal properties of all polymers were also investigated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), and these analyses have indicated that these polymers possess higher thermal stabilities than poly(methyl methacrylate) (PMMA) obtained via free radical polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6057–6072, 2005     

Well‐Defined Iron Complexes as Efficient Catalysts for “Green” Atom‐Transfer Radical Polymerization of Styrene,Methyl Methacrylate,and Butyl Acrylate with Low Catalyst Loadings and Catalyst Recycling

Environmentally friendly iron(II) catalysts for atom‐transfer radical polymerization (ATRP) were synthesized by careful selection of the nitrogen substituents of N,N,N‐trialkylated‐1,4,9‐triazacyclononane (R₃TACN) ligands. Two types of structures were confirmed by crystallography: “[(R₃TACN)FeX₂]” complexes with relatively small R groups have ionic and dinuclear structures including a [(R₃TACN)Fe(μ‐X)₃Fe(R₃TACN)]⁺ moiety, whereas those with more bulky R groups are neutral and mononuclear. The twelve [(R₃TACN)FeX₂]_n complexes that were synthesized were subjected to bulk ATRP of styrene, methyl methacrylate (MMA), and butyl acrylate (BA). Among the iron complexes examined, [{(cyclopentyl)₃TACN}FeBr₂] ( 4 b ) was the best catalyst for the well‐controlled ATRP of all three monomers. This species allowed easy catalyst separation and recycling, a lowering of the catalyst concentration needed for the reaction, and the absence of additional reducing reagents. The lowest catalyst loading was accomplished in the ATRP of MMA with 4 b (59 ppm of Fe based on the charged monomer). Catalyst recycling in ATRP with low catalyst loadings was also successful. The ATRP of styrene with 4 b (117 ppm Fe atom) was followed by precipitation from methanol to give polystyrene that contained residual iron below the calculated detection limit (0.28 ppm). Mechanisms that involve equilibria between the multinuclear and mononuclear species were also examined.     

Effect of ligand on the synthesis of star polymers by resorcinarene‐based ATRP initiators

The effect of the steric hindrance on the initiating properties of two multifunctional resorcinarene‐based initiators in atom transfer radical polymerization (ATRP) was studied by using Cu(I)‐complexes of three multidentate amine ligands in the polymerization of tert‐butyl acrylate and methyl methacrylate. These ligands are less sterically hindered and have higher activities in the catalysis of ATRP of (meth)acrylates than 2,2′‐bipyridine. The polymerizations were faster and more controlled than with the 2,2′‐bipyridyl catalyst, but the tendency for bimolecular coupling increased. Even though the initiator was octafunctional, the resulting star polymers had only four arms. This indicates that the steric hindrance arising from the conformations of the initiators determines the structure of the polymer, but the ligand noticeably affects the controllability of the polymerization © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3349–3358, 2005     

High‐throughput experimentation in atom transfer radical polymerization: A general approach toward a directed design and understanding of optimal catalytic systems

High‐throughput experimentation (HTE) was successfully applied in atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) for the rapid screening and optimization of different reaction conditions. A library of 108 different reactions was designed for this purpose, which used four different initiators [ethyl 2‐bromoisobutyrate, methyl 2‐bromopropionate, (1‐bromoethyl)benzene, and p‐toluenesulfonyl chloride], five metal salts (CuBr, CuCl, CuSCN, FeBr₂, and FeCl₂), and nine ligands (2,2′‐bipyridine and its derivatives). The optimal reaction conditions for Cu(I) halide, CuSCN, and Fe(II) halide‐mediated ATRP systems with 2,2′‐bipyridine and its 4,4′‐dialkyl‐substituted derivatives as ligands were determined. Cu(I)‐mediated systems were better controlled than Fe(II)‐mediated ones under the examined conditions. A bipyridine‐type ligand with a critical length of the substituted alkyl group (i.e., 4,4′‐dihexyl 2,2′‐bipyridine) exhibited the best performance in Cu(I)‐mediated systems, and p‐toluenesulfonyl chloride and ethyl 2‐bromoisobutyrate could effectively initiate Cu(I)‐mediated ATRP of MMA, resulting in polymers with low polydispersities in most cases. Besides, Cu(I) halide‐mediated ATRP with 4,5′‐dimethyl 2,2′‐bipyridine as the ligand and p‐toluenesulfonyl chloride as the initiator proved to be better controlled than those with 4,4′‐dimethyl 2,2′‐bipyridine as the ligand, and polymers with much lower polydispersities were obtained in the former cases. This successful HTE example opens up a way to significantly accelerate the development of new catalytic systems for ATRP and to improve the understanding of structure–property relationships of the reaction systems. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1876–1885, 2004     

A new tetradentate ligand for atom transfer radical polymerization

The properties of a ligand, including molecular structure and substituents, strongly affect the catalyst activity and control of the polymerization in atom transfer radical polymerization (ATRP). A new tetradentate ligand, N,N′‐bis(pyridin‐2‐ylmethyl‐3‐hexoxo‐3‐oxopropyl)ethane‐1,2‐diamine (BPED) was synthesized and examined as the ligand of copper halide for ATRP of styrene (St), methyl acrylate (MA), and methyl methacrylate (MMA), and compared with other analogous linear tetrdendate ligands. The BPED ligand was found to significantly promote the activation reaction: the CuBr/BPED complex reacted with the initiators so fast that a large amount of Cu(II)Br₂/BPED was produced and thus the polymerizations were slow for all the monomers. The reaction of CuCl/BPED with the initiator was also fast, but by reducing the catalyst concentration or adding CuCl₂, the activation reaction could be slowed to establish the equilibrium of ATRP for a well‐controlled living polymerization of MA. CuCl/BPED was found very active for the polymerization of MA. For example, 10 mol% of the catalyst relatively to the initiator was sufficient to mediate a living polymerization of MA. The CuCl/BPED, however, could not catalyze a living polymerization of MMA because the resulting CuCl₂/BPED could not deactivate the growing radicals. The effects of the ligand structures on the catalysis of ATRP are also discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3553–3562, 2004     

Star polymers by ATRP of styrene and acrylates employing multifunctional initiators

Multifunctional initiators for atom transfer radical polymerization (ATRP) are prepared by converting ditrimethylolpropane with four hydroxyl groups, dipentaerythritol with six hydroxyl groups, and poly(3‐ethyl‐3‐hydroxymethyl‐oxetane) with ～11 hydroxyl groups to the corresponding 2‐bromoisobutyrates or 2‐bromopropionates as obtained by reaction with acid bromides. Star polystyrene (PS) is produced by using these macroinitiators and neat styrene in a controlled manner by ATRP at 110 °C, employing the catalytic system CuBr and bipyridine. M_n up to 51,000 associated with narrow molecular weight distributions (PDI < 1.1) are obtained with conversions up to 32%. Hydrolysis of the star‐PS leads to linear chains having the expected M_n values. The star‐PS polymers based on dipentaerythritol degrade thermally in nitrogen in a two‐step process in which the first low‐temperature step involves scission of the ester linkages and the second step corresponds to the normal PS degradation. Star poly(methyl acrylates) with various cores are likewise prepared in a controlled manner by ATRP of methyl acrylate in bulk and in solution at 60–80 °C with the 1,1,4,7,7‐pentamethyldiethylene triamine ligand. Under these conditions, higher conversions were possible still maintaining low PDI signaling controlled star growth. Multiarm stars of poly(n‐butyl acrylate) and poly(n‐hexyl acrylate) with controlled characteristics have also been prepared. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3748–3759, 2005     

Polymer–silicate nanocomposites produced by in situ atom transfer radical polymerization

Polymer–silicate nanocomposites were synthesized with atom transfer radical polymerization (ATRP). An ATRP initiator, consisting of a quaternary ammonium salt moiety and a 2‐bromo‐2‐methyl propionate moiety, was intercalated into the interlayer spacings of the layered silicate. Subsequent ATRP of styrene, methyl methacrylate, or n‐butyl acrylate with Cu(I)X/N,N‐bis(2‐pyridiylmethyl) octadecylamine, Cu(I)X/N,N,N′,N′,N″‐pentamethyldiethylenetriamine, or Cu(I)X/1,1,4,7,10,10‐hexamethyltriethylenetetramine (X = Br or Cl) catalysts with the initiator‐modified silicate afforded homopolymers with predictable molecular weights and low polydispersities, both characteristics of living radical polymerization. The polystyrene nanocomposites contained both intercalated and exfoliated silicate structures, whereas the poly(methyl methacrylate) nanocomposites were significantly exfoliated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 916–924, 2004     

Synthesis of nitroxide‐containing block copolymers for the formation of organic cathodes

This contribution describes the polymerization of 2,2,6,6‐tetramethylpiperidin‐4‐yl methacrylate by atom transfer radical polymerization (ATRP). Different catalytic systems are compared. The CuCl/4,4′‐dinonyl‐2,2′‐dipyridyl catalytic system allows a good control over the polymerization and provides polymers with a polydispersity index below 1.2. The successful polymerization of styrene from PTMPM‐Cl macroinitiators by ATRP is then demonstrated. Successful quantitative oxidation of PTMPM‐b‐PS block copolymers leads to poly(2,2,6,6‐tetramethylpiperidinyloxy‐4‐yl‐methacrylate)‐b‐poly(styrene) (PTMA‐b‐PS). The cyclic voltammogram of PTMA‐b‐PS indicates a reversible redox reaction at 3.6 V (vs. Li⁺/Li). Such block copolymers open new opportunities for the formation of functional organic cathode materials. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of liquid crystalline–amorphous block copolymers by the combination of atom transfer and photoinduced radical polymerization mechanisms

The synthesis of ABA‐type block copolymers, involving liquid‐crystalline 6‐(4‐cyanobiphenyl‐4′‐oxy)hexyl acrylate (LC6) and styrene (St) monomer with copper‐based atom transfer radical polymerization (ATRP) and photoinduced radical polymerization (PIRP), was studied. First, photoactive α‐methylol benzoin methyl ether was esterified with 2‐bromopropionyl bromide, and it was subsequently used for ATRP of LC6 in diphenylether in conjunction with CuBr/N,N,N′,N″,N″‐pentamethyldiethylenetriamine as a catalyst. The obtained photoactive functional liquid‐crystalline polymer, poly[6‐(4‐cyanobiphenyl‐4′‐oxy)hexyl acrylate] (PLC6), was used as an initiator in PIRP of St. Similarly, photoactive polystyrenes were also synthesized and employed for the block copolymerization of LC6 in the second stage. The spectral, thermal, and optical measurements confirmed a full combination of ATRP and PIRP, which resulted in the formation of ABA‐type block copolymers with very narrow polydispersities. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1892–1903, 2003     

Synthesis of diblock copolymers by combining stable free radical polymerization and atom transfer radical polymerization

A stable nitroxyl radical functionalized with an initiating group for atom transfer radical polymerization (ATRP), 4‐(2‐bromo‐2‐methylpropionyloxy)‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy (Br‐TEMPO), was synthesized by the reaction of 4‐hydroxyl‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy with 2‐bromo‐2‐methylpropionyl bromide. Stable free radical polymerization of styrene was then carried out using a conventional thermal initiator, dibenzoyl peroxide, along with Br‐TEMPO. The obtained polystyrene had an active bromine atom for ATRP at the ω‐end of the chain and was used as the macroinitiator for ATRP of methyl acrylate and ethyl acrylate to prepare block copolymers. The molecular weights of the resulting block copolymers at different monomer conversions shifted to higher molecular weights and increased with monomer conversion. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2468–2475, 2006     

Synthesis of poly(vinylidene fluoride)‐b‐poly(styrene sulfonate) block copolymers by controlled radical polymerizations

Block copolymers based on poly(vinylidene fluoride), PVDF, and a series of poly(aromatic sulfonate) sequences were synthesized from controlled radical polymerizations (CRPs). According to the aromatic monomers, appropriate techniques of CRP were chosen: either iodine transfer polymerization (ITP) or atom transfer radical polymerization (ATRP) from PVDF‐I macromolecular chain transfer agents (CTAs) or PVDF‐CCl₃ macroinitiator, respectively. These precursors were produced either by ITP of VDF with C₆F₁₃I or by radical telomerization of VDF with chloroform, respectively. Poly(vinylidene fluoride)‐b‐poly(sodium styrene sulfonate), PVDF‐b‐PSSS, block copolymers were produced from both techniques via a direct polymerization of sodium styrene sulfonate (SSS) monomer or an indirect way with the use of styrene sulfonate ethyl ester (SSE) as a protected monomer. Although the reaction led to block copolymers, the kinetics of ITP of SSS showed that PVDF‐I macromolecular CTAs were not totally efficient because a limitation of the CTA consumption (56%) was observed. This was probably explained by both the low activity of the CTA (that contained inefficient PVDF‐CF₂CH₂? I) and a fast propagation rate of the monomer. That behavior was also noted in the ITP of SSE. On the other hand, ATRP of SSS initiated by PVDF‐CCl₃ was more controlled up to 50% of conversion leading to PVDF‐b‐PSSS block copolymer with an average number molar mass of 6000 g·mol^?1. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Atom transfer radical polymerization of N‐vinyl carbazole: Optimization to characterization

The homopolymerization of N‐vinylcarbazole was performed with atom transfer radical polymerization (ATRP) with Cu(I)/Cu(II)/2,2′‐bipyridine (bpy) as the catalyst system at 90 °C in toluene. N‐2‐Bromoethyl carbazole was used as the initiator, and the optimized ratio of Cu(I) to Cu(II) was found to be 1/0.3. The resulting homopolymer, poly(N‐vinylcarbazole) (PVK), was formed after a monomer conversion of 76% in 20 h. The molecular weight as well as the polydispersity index (PDI) showed a linear relation with the conversion, which showed control over the polymerization. A semilogarithmic plot of the monomer conversion with time was linear, indicating the presence of constant active species throughout the polymerization. The initiator efficiency and the effect of the variation of the initiator concentration on the polymerization were studied. The effects of the addition of CuBr₂, the variation of the catalyst concentration with respect to the initiator, and CuX (X = Br or Cl) on the kinetics of homopolymerization were determined. With Cu(0)/CuBr₂/bpy as the catalyst, faster polymerization was observed. For a chain‐extension experiments, PVK (number‐average molecular weight = 1900; PDI = 1.24) was used as a macroinitiator for the ATRP of methyl methacrylate, and this resulted in the formation of a block copolymer that gave a monomodal curve in gel permeation chromatography. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1745–1757, 2006     

Insight into the ATRP rate controlling ability of initiator structure: Micromolecular,macromolecular, and immobilized initiators

The equilibrium constant (K_ATRP) is a key factor for ensuring a successful atom transfer radical polymerization (ATRP), which guarantees a controlled process with predictable product properties. In this work, the effect of initiator type (i.e., micromolecular, macromolecular, and immobilized initiator) on the ATRP kinetics was studied through a developed mathematical model. It was validated thoroughly via experiments using fluorinated monomer (2,2,3,3,4,4,4‐heptafluorobutyl methacrylate) as model component. The results show that the activity and deactivity of the copper(I) chlorine/1,1,4,7,7‐pentamethyldiethylenetriamine (Cu^ICl/PMDETA) heterogeneous catalytic complex is the highest for ethyl 2‐bromoisobutyrate (Eib‐Br), lower for bromo‐poly(styrene) (PS‐Br), and the lowest for bromo‐aminopropyl functionalized SiO₂ (SiO₂‐APTS‐Br). The initiation system of Eib‐Br with Cu^ICl/4,4′‐dinonyl‐2,2′‐bipyridyl (dNbpy) has relatively lower activating ability, but the polymerization keeps controllable by its higher deactivating ability. In addition, this homogeneous catalytic system (Cu^ICl/dNbpy) is facile for further implementing the developed model to guide for the preparation of fluorinated gradient copolymers by semi‐batch ATRP. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2228–2238     

Iron‐mediated atom transfer radical polymerization of styrene with tris(3,6‐dioxaheptyl) amine as a ligand

The atom transfer radical bulk polymerization of styrene with FeX₂ (X = Br or Cl)/tris(3,6‐dioxaheptyl) amine as the catalyst system was successfully implemented at 110 °C. The number‐average molecular weight of the polymers with a narrow molecular weight distribution (weight‐average molecular weight/number‐average molecular weight = 1.2–1.5) increased linearly with the monomer conversion and matched the predicted molecular weight. The polymerization rate, initiation efficiency, and molecular weight distribution were influenced by the selection of the initiator and iron halide. The high functionality of the halide end group in the obtained polymers was confirmed by both ¹H NMR and a chain‐extension reaction. Because of its water solubility, the iron complexes could be removed easily from the reaction mixture through the washing of the polymerization mixture with water. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 483–489, 2006     

In situ atom transfer radical polymerization of styrene with a tetraethylthiuram disulfide/copper bromide/2,2′‐bipyridine initiating system

The living radical polymerization of styrene in bulk was successfully performed with a tetraethylthiuram disulfide/copper bromide/2,2′‐bipyridine (bpy) initiating system. The initiator Et₂NCS₂Br and the catalyst cuprous bromide (CuBr) were produced from the reactants in the system through in situ atom transfer radical polymerization (ATRP). A plot of natural logarithm of the ratio of original monomer concentration to monomer concentration at present, ln([M]₀/[M]) versus time gave a straight line, indicating that the kinetics was first‐order. The number‐average molecular weight from gel permeation chromatography (GPC) of obtained polystyrenes did not agree well with the calculated number‐average molecular weight but did correspond to a 0.5 initiator efficiency. The polydispersity index (i.e., the weight‐average molecular weight divided by the number‐average molecular weight) of obtained polymers was as low as 1.30. The resulting polystyrene with α‐diethyldithiocarbamate and ω‐Br end groups could initiate methyl methacrylate polymerization in the presence of CuBr/bpy or cuprous chloride/bpy complex catalyst through a conventional ATRP process. The block polymer was characterized with GPC, ¹H NMR, and differential scanning calorimetry. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4001–4008, 2001     

Direct polymerization of surface‐tethered polyelectrolyte layers in aqueous solution via surface‐confined atom transfer radical polymerization

The direct polymerization of deprotonated acidic monomers in aqueous solutions was achieved via surface‐confined atom transfer radical polymerization (SC‐ATRP) to produce surface‐tethered polyelectrolyte brushes. Layers of poly(itaconic acid), poly(methacrylic acid), and sodium poly(styrene sulfonate) were grown by SC‐ATRP from self‐assembled initiator monolayers of [BrC(CH₃)₂COO(CH₂)₁₁S]₂ on gold substrates. The polymer layers were characterized with variable‐angle ellipsometry and external‐reflection Fourier transform infrared spectroscopy. Without intervention, atom transfer radical polymerization catalysts were deactivated by complexation with the deprotonated acidic monomers, disproportionation, and dissociation during the polymerization of these monomers in water; the result was the cessation of polymer growth. The addition of an alkali salt to the reaction media suppressed catalyst deactivation, allowing polymer layers to increase in thickness linearly for longer periods of time with respect to salt‐free conditions. This result suggested an improved degree of polymerization control. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 566–575, 2007     

Synthesis and characterization of mid‐ and end‐chain functional telechelics by controlled polymerization methods and coupling processes

Well‐defined polystyrene‐ (PSt) or poly(ε‐caprolactone) (PCL)‐based polymers containing mid‐ or end‐chain 2,5 or 3,5‐ dibromobenzene moieties were prepared by controlled polymerization methods, such as atom transfer radical polymerization (ATRP) or ring opening polymerization (ROP). 1,4‐Dibromo‐2‐(bromomethyl)benzene, 1,3‐dibromo‐5‐(bromomethyl)benzene, and 1,4‐dibromo‐2,5‐di(bromomethyl)benzene were used as initiators in ATRP of styrene (St) in conjunction with CuBr/2,2′‐bipyridine as catalyst. 2,5‐Dibromo‐1,4‐(dihydroxymethyl)benzene initiated the ROP of ε‐caprolactone (CL) in the presence of stannous octoate (Sn(Oct)₂) catalyst. The reaction of these polymers with amino‐ or aldehyde‐functionalized monoboronic acids, in Suzuki‐type couplings, afforded the corresponding telechelics. Further functionalization with oxidable groups such as 2‐pyrrolyl or 1‐naphthyl was attained by condensation reactions of the amino or aldehyde groups with low molecular weight aldehydes or amines, respectively, with the formation of azomethine linkages. Preliminary attempts for the synthesis of fully conjugated poly(Schiff base) with polymeric segments as substituents, by oxidative polymerization of the macromonomers, are presented. All the starting, intermediate, or final polymers were structurally analyzed by spectral methods (¹H NMR, ¹³C NMR, and IR). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 727–743, 2006