Formation of oxygen vacancies on the TiO2(1 1 0) surfaces

Density functional theory was employed to investigate the formation and properties of the oxygen vacancies on the rutile TiO₂(1 1 0) surface. It is found that the formation of the positively charged bridging-oxygen vacancy (BOV⁺, 4.2 eV) is the most favored one, followed by the positively charged in-plane-oxygen vacancy (POV⁺, 4.5 eV). In contrast, the formation of the neutral bridging-oxygen and in-plane-oxygen vacancies (BOV and POV), and their dication oxygen vacancies (BOV²⁺ and POV²⁺) needs much higher energies (7.9 and 8.3 vs. 8.1 and 8.6 eV), respectively.     

Thermally-induced morphological transition in WOx deposited on a ZrO2(1 0 0) substrate

A combined atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) study of tungsten oxide model catalysts is presented. The model catalysts were prepared by applying the real preparation method to a ZrO₂(1 0 0) single crystal support. AFM imaged several granular structures of scattered dimensions on the surface of ZrO₂(1 0 0) in the as prepared samples. After heating, at low loading the tungsten species rearranged into small WO_x particles strongly interacting with the substrate. At high tungsten content large WO₃ aggregates also formed. XPS analysis confirmed these changes. The estimated surface density of the interacting W-containing species closely matched that of real catalysts.     

Photoemission study of the modification of the electronic structure of transition-metal overlayers on TiO2 surfaces: I. Fe on TiO2(1 1 0)

The electronic states of the Fe overlayers on TiO₂(1 1 0) surfaces have been investigated using normal-emission and resonant photoelectron spectroscopy with synchrotron radiation. It was found that Fe grows in a Stranski-Krastanov mode. At low coverages, Fe deposition on TiO₂(1 1 0) is supposed to create surface Ti³⁺(3d¹) ions leading to the same in-gap emission as that is produced by surface oxygen vacancies of TiO₂. At high coverages, Fe-induced in-gap emission is evolved into a bulk Fe spectrum. However, at the beginning, a Fermi edge is not observed, indicating that the small Fe clusters of non-metallic nature are formed. A sharp Fermi edge is formed at higher coverages, indicating that the cluster becomes metallic as the size increases.     

Hydroxylated α-Al2O3 (0 0 0 1) surfaces and metal/α-Al2O3 (0 0 0 1) interfaces

X-ray photoelectron spectroscopy was applied to study the hydroxylation of α-Al₂O₃ (0 0 0 1) surfaces and the stability of surface OH groups. The evolution of interfacial chemistry of the α-Al₂O₃ (0 0 0 1) surfaces and metal/α-Al₂O₃ (0 0 0 1) interfaces are well illustrated via modifications of the surface O1s spectra. Clean hydroxylated surfaces are obtained through water- and oxygen plasma treatment at room temperature. The surface OH groups of the hydroxylated surface are very sensitive to electron beam illumination, Ar⁺ sputtering, UHV heating, and adsorption of reactive metals. The transformation of a hydroxylated surface to an Al-terminated surface occurs by high temperature annealing or Al deposition.     

The investigation of room temperature ferromagnetism in (1 0 0) oriented BaNb2O6 PLD films on LaAlO3 (1 0 0) substrate

(1 0 0) oriented BaNb₂O₆ films have been successfully grown on LaAlO₃ (1 0 0) substrate at 750 °C or 450 °C in vacuum by pulsed laser deposition. The deposited BaNb₂O₆ PLD films exhibit room-temperature ferromagnetism. Ab initio calculations demonstrate that stoichiometric BaNb₂O₆ and that with barium vacancy are nonmagnetic, while oxygen and niobium vacancy can induce magnetism due to the spin-polarization of Nb s electrons and O p electrons respectively. Moreover, ferromagnetic coupling is energetically more favorable when two Nb/O vacancies are located third-nearest-neighbored. The observed room temperature ferromagnetism in BaNb₂O₆ films should be mainly induced by oxygen vacancies introduced during vacuum deposition, with certain contribution by Nb vacancies.     

DFT study of Pt adsorption on low index SrTiO3 surfaces: SrTiO3(1 0 0), SrTiO3(1 1 1) and SrTiO3(1 1 0)

Density Functional Theory has been used to determine the energetically preferred structures of submonolayer, monolayer, and multilayer Pt films on both ideal terminations of SrTiO₃(1 0 0), SrTiO₃(1 1 1), and SrTiO₃(1 1 0). The strength of the resulting metal/metal oxide interfaces was characterized by the adsorption energy of the film and the film’s work of separation. The two polar surfaces, SrTiO₃(1 1 1) and SrTiO₃(1 1 0), form significantly stronger interfaces than the non-polar SrTiO₃(1 0 0) surface. Approximate criteria were applied to predict the growth mode of Pt on each surface.     

Metal organic chemical vapor deposition of ultrathin ZrO2 films on Si(1 0 0) and Si(1 1 1) studied by electron spectroscopy

The growth of ultrathin ZrO₂ films on Si(1 0 0)-(2 × 1) and Si(1 1 1)-(7 × 7) has been studied with core level photoelectron spectroscopy and X-ray absorption spectroscopy. The films were deposited sequentially by chemical vapor deposition in ultra-high vacuum using zirconium tetra-tert-butoxide as precursor. Deposition of a > 50 Å thick film leads in both cases to tetragonal ZrO₂ (t-ZrO₂), whereas significant differences are found for thinner films. On Si(1 1 1)-(7 × 7) the local structure of t-ZrO₂ is not observed until a film thickness of 51 Å is reached. On Si(1 0 0)-(2 × 1) the local geometric structure of t-ZrO₂ is formed already at a film thickness of 11 Å. The higher tendency for the formation of t-ZrO₂ on Si(1 0 0) is discussed in terms of Zr-O valence electron matching to the number of dangling bonds per surface Si atom. The Zr-O hybridization within the ZrO₂ unit depends furthermore on the chemical composition of the surrounding. The precursor t-butoxy ligands undergo efficient C-O scission on Si(1 0 0), leaving carbonaceous fragments embedded in the interfacial layer. In contrast, after small deposits on Si(1 1 1) stable t-butoxy groups are found. These are consumed upon further deposition. Stable methyl and, possibly, also hydroxyl groups are found on both surfaces within a wide film thickness range.     

The interaction of ultrathin Cr layers with SrTiO3(1 0 0)

The growth of ultrathin Cr overlayers on SrTiO₃(1 0 0) was studied by X-ray photoelectron spectroscopy, scanning tunneling microscopy, and transmission electron microscopy. It is found that the metal-oxide interaction strongly depends on the deposition temperature. At T < 600 °C, the interfaces are atomically sharp. Local charge transfer happens between the interfacial Cr adatoms and the topmost substrate atoms. The binding energy shift of Cr 2p is dominated by the final state effects. In case of T > 600 °C, bulk diffusion of oxygen in the oxide substrate may occur, which results in a redox reaction and the formation of new reaction phases at the interfaces. In this temperature regime, the binding energy shift of Cr 2p is mainly controlled by the initial state effects.     

Autocatalytic partial reduction of FeO(1 1 1) and Fe3O4(1 1 1) films by atomic hydrogen

The interaction of atomic hydrogen with thin epitaxial FeO(1 1 1) and Fe₃O₄(1 1 1) films was studied by TDS, XPS and LEED. On the thin, one Fe-O bilayer thick FeO film, partial reduction occurs in two steps during exposure. It ends after removal of 1/4 monolayer (ML) of oxygen with a 2 × 2 pattern appearing in LEED. This FeO_0.75 film is passive against further reduction. The first reduction step saturates after removal of ∼0.2 ML and shows autocatalytic kinetics with the oxygen vacancies formed during reduction causing acceleration. The second step is also autocatalytic and is related with reduction to the final composition and an improvement of the 2 × 2 order. A structure model explaining the two-step reduction is proposed. On the thick Fe₃O₄ film, irregular desorption bursts of H₂O and H₂ were observed during exposure. Their occurrence appears to depend on the film quality and thus on surface order. Because of the healing of reduction-induced oxygen vacancies by exchange of oxygen or iron with the bulk, a change of the surface composition was not visible. The existence of partially reduced oxide phases resistant even to atomic hydrogen is relevant to the mechanism of dehydrogenation reactions using iron oxides as catalysts.     

Structure and adhesion of MoSi2/Ni interfaces: Evaluation of MoSi2 as an alternative bond coat alloy

We use density functional theory to evaluate the stability of molybdenum disilicide coatings on a nickel substrate, as a possible bond coat alloy for high temperature coating applications. We consider the MoSi₂(0 0 1)/Ni(1 1 1), MoSi₂(1 0 0)/Ni(1 1 1), and MoSi₂(1 1 0)/Ni(1 1 1) interfaces and predict quite strong (3.5-3.8 J/m²) adhesion of this metal-silicide ceramic to nickel. The origin of this strong adhesion is elucidated by examining the geometric and electronic structure of the interfaces. We predict that Mo and Si atoms at the interface primarily occupy Ni 3-fold hollow sites, the typical adsorption site on Ni(1 1 1). Projected local densities of states and electron density difference plots reveal a mixture of localized, covalent Si-Ni bonds and more delocalized metallic Mo-Ni bonding, as the origin of the strong interfacial bonding. As emphasized in our earlier work, creation of strong covalent bonds at interfaces results in very strong adhesion. Such strong adhesion makes MoSi₂ a potential candidate for use in thermal barrier applications, in conjunction with a yttria-stabilized zirconia topcoat.     

Ultrathin ZrO2 films on Si-rich SiC(0 0 0 1)-(3 × 3): Growth and thermal stability

The growth and thermal stability of ultrathin ZrO₂ films on the Si-rich SiC(0 0 0 1)-(3 × 3) surface have been explored using photoelectron spectroscopy (PES) and X-ray absorption spectroscopy (XAS). The films were grown in situ by chemical vapor deposition using the zirconium tetra tert-butoxide (ZTB) precursor. The O 1s XAS results show that growth at 400 °C yields tetragonal ZrO₂. An interface is formed between the ZrO₂ film and the SiC substrate. The interface contains Si in several chemically different states. This gives evidence for an interface that is much more complex than that formed upon oxidation with O₂. Si in a 4+ oxidation state is detected in the near surface region. This shows that intermixing of SiO₂ and ZrO₂ occurs, possibly under the formation of silicate. The alignment of the ZrO₂ and SiC band edges is discussed based on core level and valence PES spectra. Subsequent annealing of a deposited film was performed in order to study the thermal stability of the system. Annealing to 800 °C does not lead to decomposition of the tetragonal ZrO₂ (t-ZrO₂) but changes are observed within the interface region. After annealing to 1000 °C a laterally heterogeneous layer has formed. The decomposition of the film leads to regions with t-ZrO₂ remnants, metallic Zr silicide and Si aggregates.     

Epitaxial growth of Co(0 0 0 1)hcp/Fe(1 1 0)bcc magnetic bi-layer films on SrTiO3(1 1 1) substrates

Co(0 0 0 1)_hcp/Fe(1 1 0)_bcc epitaxial magnetic bi-layer films were successfully prepared on SrTiO₃(1 1 1) substrates. The crystallographic properties of Co/Fe epitaxial magnetic bi-layer films were investigated. Fe(1 1 0)_bcc soft magnetic layer grew epitaxially on SrTiO₃(1 1 1) substrate with two type variants, Nishiyama–Wasserman and Kurdjumov–Sachs relationships. An hcp-Co single-crystal layer is obtained on Ru(0 0 0 1)_hcp interlayer, while hcp-Co layer formed on Au(1 1 1)_fcc or Ag(1 1 1)_fcc interlayer is strained and may involve fcc-Co phase. It has been shown possible to prepare Co/Fe epitaxial magnetic bi-layer films which can be usable for patterned media application.     

Methanol adsorption on a CeO2(1 1 1)/Cu(1 1 1) thin film model catalyst

Adsorption and desorption of methanol on a CeO₂(1 1 1)/Cu(1 1 1) thin film surface was investigated by XPS and soft X-ray synchrotron radiation PES. Resonance PES was used to determine the occupancy of the Ce 4f states with high sensitivity. Methanol adsorbed at 110 K formed adsorbate multilayers, which were partially desorbed at 140 K. Low temperature desorption was accompanied by formation of chemisorbed methoxy groups. Methanol strongly reduced cerium oxide by forming hydroxyl groups at first, which with increasing temperature was followed by creation of oxygen vacancies in the topmost cerium oxide layer due to water desorption. Dissociative methanol adsorption and creation of oxygen vacancies was observed as a Ce⁴⁺ → Ce³⁺ transition and an increase of the Ce 4f electronic state occupancy.     

Characterization of single-crystalline In2O3 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

Epitaxial In₂O₃ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates by metalorganic chemical vapor deposition (MOCVD). The films were deposited at different substrate temperatures (450-750 °C). The film deposited at 650 °C has the best crystalline quality, and observation of the interface area shows a clear cube-on-cube epitaxial relationship of In₂O₃(1 0 0)||YSZ(1 0 0) with In₂O₃[0 0 1]||YSZ[0 0 1]. The Hall mobility of the single-crystalline In₂O₃ film deposited at 650 °C is as high as 66.5 cm² V⁻¹ s⁻¹ with carrier concentration of 1.5 × 10¹⁹ cm⁻³ and resistivity of 6.3 × 10⁻³ Ω cm. The absolute average transmittance of the obtained films in the visible range exceeds 95%.     

A density functional theory study of formaldehyde adsorption and oxidation on CeO2(1 1 1) surface

The effects of different oxygen species and vacancies on the adsorption and oxidation of formaldehyde over CeO₂(1 1 1) surface were systematically investigated by using density functional theory (DFT) method. On the stoichiometric CeO₂(1 1 1) surface, the C-H bond rupture barriers of chemisorbed formaldehyde are much higher than that of formaldehyde desorption. On the reduced CeO₂(1 1 1) surface, the energy barriers of C-H bond ruptures are less than those on the stoichiometric CeO₂(1 1 1) surface. If the C-H bond rupture occurs, CO and H₂ form quickly with low energy barriers. When O₂ adsorbs on the reduced (1 1 1) surface (O₂/O_v species), the C-H bond rupture barriers of formaldehyde are greatly reduced in comparison with those on the stoichiometric CeO₂(1 1 1) surface. If O₂ adsorbs on oxygen vacancy at sub-layer surface, its oxidative roles on formaldehyde are much similar to that of O₂/O_v species.     

A density functional theory study of ethylene adsorption on Ni10(1 1 1), Ni13(1 0 0) and Ni10(1 1 0) surface cluster models and Ni13 nanocluster

Ethylene adsorption was studied by use of DFT/B3LYP with basis set 6-31G(d,p) in Gaussian’03 software. It was found that ethylene has adsorbed molecularly on all clusters with π adsorption mode. Relative energy values were calculated to be −50.86 kcal/mol, −20.48 kcal/mol, −32.44 kcal/mol and −39.27 kcal/mol for Ni₁₃ nanocluster, Ni₁₀(1 1 1), Ni₁₃(1 0 0) and Ni₁₀(1 1 0) surface cluster models, respectively. Ethylene adsorption energy is inversely proportional to Ni coordination number when Ni₁₀(1 1 1), Ni₁₃(1 0 0) and Ni₁₀(1 1 0) cluster models and Ni₁₃ nanocluster are compared with each other.     

The effect of preadsorbed K on the size distribution of Au nanoparticles on TiO2(1 1 0) surface

The effect of K on the morphology of Au nanoparticles deposited on TiO₂(1 1 0) surface is investigated by STM-STS and AES methods. For comparison, the enhanced concentration of oxygen defect sites generated by Ar⁺ bombardment was also studied. It was found that both the K additive and the oxygen defect sites induce a pronounced decrease in the average size of the Au nanoparticles evolved at 320 K. On the clean TiO₂(1 1 0) the average size of Au particles is 4.3 nm at approximately monolayer coverage of gold, while in the presence of K or oxygen vacancies this value decreased to 2.5 nm. In spite of the reduced average diameter detected at room temperature, the mean size of the Au nanoparticles increased significantly from 2.5 nm up to 7 nm on the effect of annealing at 500-700 K for K precoverages of 0.3-1 ML. For the clean and the Ar⁺ pretreated TiO₂(1 1 0) surfaces the mean size of the Au particles changed only slightly on the effect of the same thermal treatments.     

Adsorption structure of acetic anhydride on a TiO2(1 1 0) surface observed by scanning tunneling microscopy

The carboxylic acids are stably adsorbed on TiO₂(1 1 0) surfaces at room temperature. To demonstrate the neutralization mechanism proposed by Ashima et al. [H. Ashima, W.-J. Chun, K. Asakura, Surf. Sci. 601 (2007) 1822.] that explains the stable adsorption of carboxylic acids, we studied the full-coverage adsorption structure of acetic anhydride on a TiO₂(1 1 0) surface by STM (scanning tunneling microscopy). We directly observed three postulated species on the TiO₂(1 1 0) surface; normal acetates (termed acetate A) forming a (2 × 1) ordered structure, a minor acetate species (termed acetate B) which was present between the bridging oxygen and the 5-fold Ti, and the oxygen vacancies. We determined the ratio of these three species. This ratio was in good agreement with the postulated conversion reaction of acetate B to A.     

A study of the effect of ZrO2 on the magnetic properties of FePt/ZrO2 multilayer

Fe_xPt_100−x(30 nm) and [Fe_xPt_100−x(3 nm)/ZrO₂]₁₀ (x = 37, 48, 57, 63, 69) films with different ZrO₂ content were prepared by RF magnetron sputtering technique, then were annealed at 550 °C for 30 min. This work investigates the effect of ZrO₂ doping on the microstructural evolution, magnetic properties, grain size, as well as the ordering kinetics of FePt alloy films. The as-deposited films behaved a disordered state, and the ordered L1₀ structure was obtained by post-annealing. The magnetic properties of the films are changed from soft magnetism to hard magnetism after annealing. The variation of the largest coercivities of [Fe_xPt_100−x/ZrO₂]₁₀ films with the Fe atomic percentage, x and differing amounts of ZrO₂ content reveals that as we increase the ZrO₂ content we must correspondingly increase the amount of Fe. This phenomenon suggests that the Zr or O atoms of ZrO₂ preferentially react with the Fe atoms of FePt alloy to form compounds. In addition, introducing the nonmagnetic ZrO₂ can reduce the intergrain exchange interactions of the FePt/ZrO₂ films, and the interactions are decreased as the ZrO₂ content increases, the dipole interactions are observed in FePt/ZrO₂ films as the ZrO₂ content is more than 15%.     

Chloromethane surface chemistry on Fe3O4(1 1 1)-(2 × 2): A thermal desorption spectrometry comparison of CCl4, CBr2Cl2, and CH2Cl2

The surface chemistry of CBr₂Cl₂ on the Fe₃O₄(1 1 1)-(2 × 2) selvedge of single-crystal α-Fe₂O₃(0 0 0 1) has been investigated using temperature programmed reaction and desorption (TPR/D) measurements. The spectra obtained in this case show that strong chemisorption occurs and that a series of adsorbed halogenated reaction products are present. By comparison, studies of the adsorbed phase of CH₂Cl₂ show that only physisorption occurs. The TPR/D spectra of CBr₂Cl₂ show that dissociative formation of CCl₂ followed by its reaction with lattice oxygen is central to the monolayer reaction chemistry in this chloromethane. The branching ratios of the various desorbed products are compared with those obtained from CCl₄ adsorbed on the same (2 × 2) surface.