硅倍半氧烷改性聚酰亚胺(PI/Si)复合膜性能简

通过在聚酰亚胺(PI)中分别添加笼型八氨基苯基硅倍半氧烷(OAPS)、笼型八苯基硅倍半氧烷(OPS)、梯形聚苯基硅倍半氧烷(PPSQ)和无机纳米SiO2,制备了4种含硅聚酰亚胺(PI/Si)复合膜. 对PI/Si复合膜的相容性、力学性能、热性能和阻燃性能进行了研究. 结果表明,OAPS与PI间展现出较好的相容性,PPSQ次之,而OPS,SiO2与PI的相容性较差;但相容性与复合膜的力学和热性能无明显的对应关系. SiO2可提高PI的力学性能;PI/OAPS复合膜的Tg最高;OAPS,PPSQ或SiO2的加入使PI复合膜的热稳定性稍有提高,而少量OPS的加入大大降低PI膜的热稳定性. 这类PI/Si复合膜的显著特点是能够大幅提高PI膜的极限氧指数,含硅化合物能够增加PI燃烧后残炭量,使残炭的形貌得到显著改善. PI/Si复合膜在燃烧过程中在表面形成一层白色含硅包裹层,起到隔热隔氧及保护内层有机物不被燃烧的作用. 硅倍半氧烷对炭层形貌的改善显著,展现出比SiO2更好的阻燃性能.     

多面体低聚八(二苯砜基)硅倍半氧烷合成优化及磺酰化机理研究

以笼型低聚八苯基硅倍半氧烷(OPS)为原料,AlCl3为催化剂,苯磺酰氯为磺酰化试剂,在二氯甲烷溶液中反应72h,合成了笼型八(二苯砜基)硅倍半氧烷(ODPSS).该方法合成过程简单稳定,产率高.通过FTIR、MALDI-TOF MS、1H NMR、13C NMR、29Si NMR和元素分析对产物进行了表征,证明OPS已完全转化为ODPSS.通过改变溶剂、催化剂、反应时间和各反应物物质的量之比,优化了反应条件,分析了反应机理,建立了该体系下OPS的磺酰化反应机理模型.     

多面体低聚八氨基苯基硅倍半氧烷合成方法改进及其表征

以八硝基苯基硅倍半氧烷(ONPS)为原料, 5% Pd/C 和FeCl₃ 为催化剂, 水合肼为还原剂, 在四氢呋喃溶液中反应 1 h 合成了八氨基苯基硅倍半氧烷(OAPS). 相比文献中已有的其它合成方法, 该方法合成过程简单且稳定, 催化效率高、产率高、周期短. 通过FTIR, ¹H NMR, GPC 对产物进行了表征, 证明了硝基已完全转化. 通过催化剂的控制, 分离出ONPS 向OAPS 转化过程中的一种含有羟胺和二羟胺基团的中间体. 分析了OAPS 合成机理, 提出了ONPS 和水合肼的反应历程. 认为ONPS 中的硝基先经过2 电子转移转化为二羟胺化合物, 然后经过脱水加氢生成羟胺化合物, 最后再经过脱水加氢生成OAPS; 在有ONPS 存在的情况下, 水合肼主要转化为氮气和氢气, 待ONPS 完全转化为OAPS 后, 水合肼转化为氮气和氨气.     

多面体低聚八硝基苯基硅倍半氧烷纯度分析

使用高效液相色谱-电喷雾四级杆飞行时间质谱(HPLC-ESI-Q-TOF MS)联用技术对八硝基苯基硅倍半氧烷(ONPS)纯度进行分析, 从而判定ONPS产物峰及杂质峰的位置, 根据ONPS峰和杂质峰的面积比计算ONPS的纯度. 通过改变HPLC的洗脱梯度和测试时间, 将ONPS产物中的杂质峰完全分开, 测得硝基苯基硅倍半氧烷(NPS)质量分数为97.55%, 其中ONPS的纯度约为92.42%, 产物中含有九硝基八苯基硅倍半氧烷(9-NPS)约5.13%, 其它杂质含量约为2.45%. 通过对ONPS高效液相色谱图峰形和同分异构体极性情况分析, 进一步证明ONPS分子中硝基取代发生于对位和间位. 使用超高效液相色谱(UPLC)对ONPS进行分析, 以更高的分离效率验证了HPLC的结果. 该方法可作为ONPS纯度的分析方法.     

抗原子氧聚酰亚胺的研究与应用进展

聚酰亚胺(PI)在空间飞行器中广泛用作多层热绝缘毯、太阳电池阵列的柔性基板以及电路系统的绝缘保护层。但普通型PI在低地球轨道(LEO)原子氧环境中易发生降解。因此,提高PI材料抗原子氧能力的研究近年来受到了广泛的重视。本文概述了这一研究领域内的最新进展情况,重点阐述了含苯基氧化膦(PPO)、含笼型低聚倍半硅氧烷(POSS)以及含锆基PI材料的结构与抗原子氧特性之间的关系。最后结合作者的研究工作对国内抗原子氧PI材料的研究与应用前景进行了展望。     

大分子植酸-聚有机硅倍半氧烷的合成及性能

采用溶胶-凝胶方法, 无需小分子酸催化剂, 利用硅烷化植酸的反应活性和酸催化活性, 与硅烷单体共水解缩聚, 在聚有机硅倍半氧烷分子链上原位接枝植酸, 合成了分子量大于50000的大分子植酸-聚有机硅倍半氧烷. 用GPC, 13C NMR, 29Si NMR, XPS, Raman光谱, SEM及电化学测试等分析手段进行表征, 对比不同酸催化植酸-聚有机硅倍半氧烷(PAP), 单宁酸-聚有机硅半氧烷(TAP), 盐酸-聚有机硅半氧烷(HCP)的结构和性能, 发现植酸-聚有机硅倍半氧烷上的螯合基团与金属表面的活性基团反应而键合, 在金属表面形成致密的保护膜, PAP与TAP和HCP比较具有优异的防腐性能.     

八苯基笼型倍半硅氧烷的官能化及其在高分子纳米复合材料中的应用

笼型倍半硅氧烷（POSS）是具有独特分子结构的有机硅化合物,无机硅氧骨架核心为其提供良好的硬度和热稳定性,外围有机基团可增强与聚合物基体间的相容性,以它为前驱体可以制备分子级分散的有机／无机纳米高分子杂化材料。近年来,全芳香结构的八苯基笼型倍半硅氧烷因其高的耐热性和官能化方法的多样性尤其得到关注。本文重点综述了八苯基笼...     

色谱用金属柱管的脱活研究

利用苯基三乙氧基硅烷的酸催化水解缩合反应合成了具有梯形结构的聚苯基硅倍半氧烷预聚体，再以其20％－30％的丙酮溶液对气相色谱用金属柱管进行遮盖性脱活，预聚体涂层经溶剂挥发高温老化处理后获得了能耐400℃高温的脱活涂层，。以甲醇、乙醇、异丙醇、叔丁醇为测试物，内径2mm、长3．0m，固定相为PorapackQ的填充聚四氟乙烯柱为预分离柱串接测试柱的方法对该涂层进行了评价，结果表明，经该涂层处理的不锈钢柱管在115℃时对低级醇的吸附活性与PorapackQ柱的活性相近，活性明显降低，涂层结构中含有的苯环和羟基等官能基，将提高其与固定液的相容性并为固定液的交联提供必要的活性点。     

新型氮化硼陶瓷纤维先驱体——含硅聚硼氮烷的合成与表征

以三氯化硼、六甲基二硅氮烷为起始原料, 采用一步法合成了一种新型含硅氮化硼陶瓷纤维先驱体——含硅聚硼氮烷. 该法合成工艺简单, 且合成收率约为87%(质量分数). 采用元素分析、傅立叶红外光谱、核磁共振波谱、热机械分析、动态流变分析等对含硅聚硼氮烷的组成、结构和性能进行了表征. 结果表明, N—B为含硅聚硼氮烷先驱体的骨架结构, 其中, B, N主要以硼氮六环形式存在, 而Si则以Si—CH₃, Si—N形式存在. 该先驱体软化点为110 ℃, 具有优良的成型性, 在190 ℃的N₂气氛中可纺丝得到20～25 μm的有机纤维.     

聚有机硅倍半氧烷的合成及其在涂层材料中的应用

聚有机硅倍半氧烷由于具有优异的力学、电学、光学性能,近年来被广泛应用作涂层材料以提高其热稳定性、耐腐蚀性、耐磨性、耐刮伤性、绝缘性等。介绍了聚有机硅倍半氧烷的合成方法及其在涂层材料中的应用。     

含三苯基氧磷结构聚芳醚醚酮酮的合成与表征

以苯酚、对二溴苯及苯基磷酰二氯为原料合成出二(4-苯氧基苯基)苯基氧磷(BPOPPO)。 三氯化铝(AlCl₃)为催化剂,通过缩聚反应,BPOPPO与对苯二甲酰氯(TPC)反应制备出一种含有三苯基氧磷结构的聚醚醚酮酮(P-PEEKK)树脂。 采用傅里叶变换红外光谱仪(FT-IR)、差示扫描量热仪(DSC)、热重分析仪(TGA)和广角X射线衍射(WAXD)等技术手段对P-PEEKK树脂的结构和性能进行表征。 结果表明,P-PEEKK树脂属于非晶聚合物,玻璃化转变温度(T_g)较高,为190.5 ℃;热分解温度(T_5%)为515 ℃,耐热性能较好;极限氧指数(LOI)为42,阻燃性能好,为难燃材料;易溶解于氯仿、1,2-二氯乙烷、N,N-二甲基乙酰胺等有机溶剂中,溶解性能较好,便于涂膜加工;拉伸强度为62 MPa,力学性能较好。     

Phenolic resin/polyhedral oligomeric silsesquioxane (POSS) composites: Mechanical,ablative, thermal,and flame retardant properties

Three different polyhedral oligomeric silsesquioxanes (POSS), trisilanolphenyl polyhedral oligomeric silsesquioxane (T‐POSS), octaaminophenyl polyhedral oligomeric silsesquioxanes (OAPS), and octaphenyl polyhedral oligomeric silsesquioxanes (OPS) were incorporated into phenolic resin (PR), respectively; PR/POSS composites were successfully prepared, and the properties of PR/POSS composites were studied. The limiting oxygen index (LOI), cone calorimeter, and thermal gravimetric analysis (TGA) were used for the estimation of flame retardancy and thermal stability. Oxyacetylene flame test and flexural strength test were used to study the ablative and mechanical properties of the PR/POSS composites. The results indicated that T‐POSS was more effective in improving the flame retardancy of PR than OAPS or OPS. Meanwhile, compared with pure PR, the second line ablation rates of PR/4% T‐POSS, PR/4% OAPS, and PR/4% OPS were significantly reduced by 53.3%, 61.9%, and 40.0%, respectively. In addition, the thermal stability and flexural strength of PR/4% T‐POSS were significantly higher than that of all other PR composites.     

Determination of the glass transition temperature of latex films: Comparison of various methods

The glass transition temperature (T_g) for two latices with different styrene/butadiene compositions was determined by the thermal SPM probe resonance frequency method. The results were compared with the T_g values obtained by differential scanning calorimetry (DSC), dynamical mechanical analysis (DMA), process rheometer (PR) and thermo-mechanical analyzer (TMA) measurements. The T_g values detected by the thermal SPM method agreed well with the T_g values obtained by DSC and calculated by the Fox–Flory equation. DMA, on the other hand, showed a significantly higher T_g value for both latices than those obtained from theoretical calculations, the thermal SPM method and DSC. The T_g obtained from the PR curve was slightly higher for the latex with a low styrene content, whereas good agreement was obtained with the thermal SPM data for the latex with a high styrene content. The glass transition temperature determined by TMA agreed fairly well with the thermal SPM data for the latex with the low styrene content, whilst the value of T_g for the second latex was much less than those obtained by the other methods. The thermal SPM method detects changes in thermal behavior (thermal diffusivity, heat capacity) during heating of the latex films rather than changes in the mechanical properties. Information about the sample history could be seen in the thermal SPM curves, which was further associated with the degree of latex film formation, especially when the roughness of the films was taken into consideration.     

柔性OLED用高耐热聚酰亚胺薄膜的制备与性能

聚酰亚胺(PI)薄膜作为柔性有机发光显示(OLED)基板材料应用时, 需要满足玻璃化转变温度(T_g)大于450 ℃和热膨胀系数(CTE)在0~5×10^-6 K^-1之间. 为了提高PI薄膜的热性能, 本文合成了2,7-占吨酮二胺 (2,7-DAX), 并将其与均苯四甲酸二酐(PMDA)和2-(4-氨基苯基)-5-氨基苯并噁唑(BOA)共聚制备了一系列新型PI薄膜. 研究了PI薄膜的聚集态结构、 耐热性能、 尺寸稳定性和力学性能. 结果表明, 占吨酮结构和苯并噁唑结构提高了PI分子链的刚性与线性, 使分子链在平面内紧密堆积与取向, 制备的PI薄膜综合性能优异, 玻璃化转变温度高于408 ℃, CTE在-5.0×10^-6~8.1×10^-6 K^-1之间, 拉伸强度大于140 MPa, 拉伸模量大于4.2 GPa, 断裂伸长率为7.1%~20%, 5%热失重分解温度(T_5%)在601~624 ℃之间. 其中, PI-50和PI-60薄膜具有超高玻璃化转变温度和超低热膨胀系数, T_g高于450 ℃, CTE分别为2.1×10^-6 K^-1和1.6×10^-6 K^-1. 制备的系列PI薄膜作为柔性OLED基板材料有潜在应用前景.     

SPES/PWA/SiO_2复合质子交换膜的性能

以磺化聚醚砜(SPES)为基体,以不同比例的SiO2溶胶与磷钨酸(PWA)为掺杂物,制备了一种有望用于直接甲醇燃料电池(DMFC)的新型SPES/PWA/SiO2有机-无机复合膜,并经热失重分析(TGA)、差示扫描量热仪(DSC)、扫描电镜(SEM)-X射线能谱分析(EDX)等对膜的结构和性能进行了表征,探讨了复合膜用作质子交换膜的可能性.结果表明:复合膜较纯SPES膜具有更高的热稳定性、玻璃化转变温度和吸水率;虽然在室温和电池操作温度(80℃)下,复合膜的拉伸强度均低于纯SPES膜,但即使当SiO2含量高达20%(w)时,复合膜的拉伸强度仍高于Nafion112膜的;SEM图片显示SiO2和PWA在膜中分布均匀,这将有利于连续质子传输通道的形成.对于SiO2含量为15%(w),PWA含量为6%(w)的复合膜,其室温质子传导率达到了0.034S·cm-1,与Nafion112膜的相当,但其甲醇渗透率明显降低,仅为商用Nafion112膜的七分之一左右,这表明该复合膜在直接甲醇燃料电池中具有良好的应用前景.     

Melting and glass transitions in paraffinic and naphthenic oils

Naphthenic and paraffinic oils were analyzed by modulated differential scanning calorimetry (MDSC). The results showed several improvements in the analysis of thermal properties when compared with standard DSC. The glass transition temperature (T_g), the enthalpy relaxation at T_g, and the melting endotherms could be deconvoluted, and reversible melting could be identified. This allowed for an easier interpretation of the thermal properties of the oils. With MDSC, the T_gs in mineral oils were found to coincide with endothermic enthalpy relaxation, which is generally regarded as a melting endotherm with standard DSC. A decrease in heat capacity after T_g was attributed to the existence of rigid amorphous material. From Δc_p at T_g and the oil molecular weight, the number of repeat units in the oil chains was estimated at less than 20. The T_g of a hypothetical pure aromatic oil was found to be similar to that for petroleum asphaltenes, and that for a naphthenic oil of infinite molecular weight to be similar to that of petroleum resins.     

Gas permeability in rubbery polyphosphazene membranes

The synthesis, characterization, and gas permeability of 10 new polyphosphazenes has been studied. Additionally, the first gas permeation data has been collected on hydrolytically unstable poly[bis-(chloro)phosphazene]. Gases used in this study include CO₂, CH₄, O₂, N₂, H₂, and Ar. CO₂ was the most permeable gas through any of the phosphazenes and a direct correlation between the T_g of the polymer and CO₂ transport was noted with permeability increasing with decreasing polymer T_g. To a lesser degree, permeability of all the other gases studied also yielded increases with decreasing polymer T_g. The trend observed for these new polymers was further supported by published data for other phosphazenes. Furthermore, permeability data for all gases were found to correlate to the gas condensability and the gas critical pressures, except for hydrogen, suggesting that the nature of the gas is also a significant factor for permeation through rubbery phosphazene membranes. Ideal separation factors () for the CO₂/H₂ and CO₂/CH₄ gas pairs were calculated. For CO₂/CH₄, no increase in was observed with decreasing T_g, however increases in were noted for the CO₂/H₂ pair.     

Ethanolamine as a novel plasticiser for thermoplastic starch

Ethanolamine plasticised thermoplastic starch (ETPS) was prepared using a novel plasticiser ethanolamine. SEM images show that the native starch granules were destroyed, and the ethanolamine made them come into a uniform continuous phase. FTIR spectroscopy showed that the hydrogen bonds between the ethanolamine and starch molecules weakened the strong effect of starch intermolecular and intramolecular hydrogen bonds. The ETPS successfully restrains the re-crystallization of traditional thermoplastic starch plasticised by glycerol (GTPS), which was proved by XRD. The mechanical properties of ETPS, such as Young's modulus and breaking energy and the water absorption were improved. The glass-transition temperature (T_g) and thermal stability were also studied by DSC and TGA.     

Thermotropic main chain liquid crystalline polyesters containing ferrocene and phosphate units: synthesis and characterization

A new series of liquid crystalline main chain copolyesters were prepared, having ferrocene in the mesogenic segment and a methyl phosphate group along with a methylene spacer. The even numbered methylene groups were varied from two to ten. Liquid crystalline behaviour was investigated on a hot stage optical polarized microscope. Thermal properties of the polymers were analysed by TGA and DSC, revealing that the polymers yield high char products, probably caused by the formation of phosphorus and iron oxides. The glass transition (T_g) temperatures of the polymers were found to be fairly low, the result of the incorporation of bulky phosphorus and ferrocene moieties in the chain. The phase behaviour was analysed and correlated with the structure of the polymers. The liquid crystalline textures of the polymers became more transparent with increasing spacer length. Energy minimized structures for the polymer repeating units reveal that both the ferrocene and phosphorus moieties produce more molecular entanglement, thus reducing the T_g and T_m of the polymers.