Experimental study of the blockage boundary for dense-phase pneumatic conveying of powders through a horizontal slit

The estimation of the blockage boundary for pneumatic conveying through a slit is of significant importance.In this paper,we investigate the characteristics for blockage of powder(48 μm average diameter)through a horizontal slit(1.6 m × 0.05 m × 0.002 m).The results show that the required critical solid mass flow rate increases as the superficial air velocity increases superficial air velocity.The solid loading ratio and superficial air velocity displayed a decreasing power law relationship.This finding agrees with existing theory and experimental results.However,a minimum inlet solid loading ratio exists.When the air velocity is greater than the corresponding air velocity of the minimum solid loading ratio,the solid loading ratio exhibits an increasing trend in power law.We also found that when the inlet conveying pressure increased,the critical solid mass flow rate required for blockage,the inlet solid loading ratio,and the minimum inlet solid loading ratio increased.     

Validated scale-up procedure to predict blockage condition for fluidized dense-phase pneumatic conveying systems

This paper presents results of an ongoing investigation into modelling fluidized dense-phase pneumatic conveying of powders. For the reliable design of dense-phase pneumatic conveying systems, an accurate estimation of the blockage boundary condition or the minimum transport velocity requirement is of sig- nificant importance. The existing empirical models for fine powder conveying in fluidized dense-phase mode are either based on only a particular pipeline and product or have not been tested for their accuracy under a wide range of scale-up conditions. In this paper, a validated test design procedure has been devel- oped to accurately scale-up the blockage boundary with the help of a modelling format that employs solids loading ratio and Froude number at pipe inlet conditions using conveying data of two different samples of fly ash, electro-static precipitation （ESP） dust and cement （particle densities： 2197-3637 kgJm3; loose poured bulk densities： 634-1070kg/m3; median size： 7-30 l~m）. The developed models （in power func- tion format） have been used to predict the blockage boundary for larger diameter and longer pipelines （e.g. models based on 69 mm I.D. ~ 168 m long pipe have been scaled up to 105 mm I.D. and 554 m length）. The predicted blockage boundaries for the scale-up conditions were found to provide better accuracy compared to the existing models.     

CFD-DEM simulation of the pneumatic conveying of fine particles through a horizontal slit

Fine particles play a significant role in many industrial processes.To study the dynamic behavior of fine particle and their deposition in rock fractures,the pneumatic conveying of fine particles(approximately100 μm in diameter) through a small-scale horizontal slit(0.41 m × 0.025 m) was studied,which is useful for the sealing technology of underground gas drainage in coal mining production.The CFD-DEM method was adopted to model the gas-particle two-phase flow;the gas phase was treated as a continuum and modeled using computational fluid dynamics(CFD),particle motion and collisions were simulated using the DEM code.Then,the bulk movement of fine particles through a small-scale horizontal slit was explored numerically,and the flow patterns were further investigated by visual inspection.The simulation results indicated that stratified flow or dune flow can be observed at low gas velocities.For intermediate gas velocities,the flow patterns showed pulsation phenomena,and dune flow reappeared in the tail section.Moreover,periodic flow regimes with alternating thick and sparse stream structures were observed at a high gas velocity.The simulation results of the bulk movement of fine particles were in good agreement with the experimental findings,which were obtained by video-imaging experiments.Furthermore,the calculated pressure drop versus gas velocity profile was investigated and compared with relative experimental findings,and the results showed good agreement.Furthermore,the particle velocity vectors and voidage distribution were numerically simulated.Selected stimulation results are presented and provide a reference for the further study of fine particles.     

Characterization of the gas pulse frequency, amplitude and velocity in non-steady dense phase pneumatic conveying of powders

Current modelling techniques for the prediction of conveying line pressure drop in low velocity dense phase pneumatic conveying are largely based on steady state analyses.Work in this area has been on-going for many years with only marginal improvements in the accuracy of prediction being achieved.Experimental and theoretical investigations undertaken by the authors suggest that the flow mechanisms involved in dense phase conveying are dominated by transient effects rather than those of steady state and are possibly the principal reasons for the limited improvement in accuracy.This paper reports on investigations on the pressure fluctuation behaviour in dense phase pneumatic conveying of powders.The pressure behaviour of the gas flow in the top section of the pipeline was found to exhibit pulsatile oscillations.In particular,the pulse velocity showed variation in magnitude while the frequency of the oscillations rarely exceeded 5 Hz.A wavelet analysis using the Daubechie 4 wavelet found that the amplitude of the oscillations increased along the pipeline.Furthermore,there was significant variation in gas pulse amplitude for different types of particulate material.     

Characterization of the gas pulse frequency,amplitude and velocity in non-steady dense phase pneumatic conveying of powders

Current modelling techniques for the prediction of conveying line pressure drop in low velocity dense phase pneumatic conveying are largely based on steady state analyses. Work in this area has been on-going for many years with only marginal improvements in the accuracy of prediction being achieved. Experimental and theoretical investigations undertaken by the authors suggest that the flow mechanisms involved in dense phase conveying are dominated by transient effects rather than those of steady state and are possibly the principal reasons for the limited improvement in accuracy. This paper reports on investigations on the pressure fluctuation behaviour in dense phase pneumatic conveying of powders. The pressure behaviour of the gas flow in the top section of the pipeline was found to exhibit pulsatile oscillations. In particular, the pulse velocity showed variation in magnitude while the frequency of the oscillations rarely exceeded 5 Hz. A wavelet analysis using the Daubechie 4 wavelet found that the amplitude of the oscillations increased along the pipeline. Furthermore, there was significant variation in gas pulse amplitude for different types of particulate material.     

Low-velocity pneumatic conveying in horizontal pipe for coarse particles and fine powders

First,the characteristics of low-velocity conveying of particles having different hardness are experimentally investigated in a horizontal pipeline in terms of flow pattern and pressure drop to show that the slug flow can be classified into two types depending on the settling of particles along the pipeline,and the period is small for slug flow without the settled layer,which is called solitary slug flow.The pressure drop for soft particles is shown to be larger than that for hard particles.Then,experimental results are presented on horizontal fluidized-bed conveying of fine powders to show that air release from the top surface of the conveying channel is an important factor for high mass flow rate of particles.     

Low-velocity pneumatic conveying in horizontal pipe for coarse particles and fine powders

First, the characteristics of low-velocity conveying of particles having different hardness are experimentally investigated in a horizontal pipeline in terms of flow pattern and pressure drop to show that the slug flow can be classified into two types depending on the settling of particles along the pipeline, and the period is small for slug flow without the settled layer, which is called solitary slug flow. The pressure drop for soft particles is shown to be larger than that for hard particles. Then, experimental results are presented on horizontal fluidized-bed conveying of fine powders to show that air release from the top surface of the conveying channel is an imnortant factor for high mass flow rate of particles.     

An investigation into flow mode transition and pressure fluctuations for fluidized dense-phase pneumatic conveying of fine powders

This paper presents the results of an ongoing investigation into the fluctuations of pressure signals due to solids-gas flows for dense-phase pneumatic conveying of fine powders.Pressure signals were obtained from pressure transducers installed along different locations of a pipeline for the fluidized dense-phase pneumatic conveying of fly ash(median particle diameter 30μm;particle density 2300kg/m~3;loosepoured bulk density 700kg/m~3) and white powder(median particle diameter 55 u.m;particle density1600kg/m~3;loose-poured bulk density 620kg/m~3) from dilute to fluidized dense-phase.Standard deviation and Shannon entropy were employed to investigate the pressure signal fluctuations.It was found that there is an increase in the values of Shannon entropy and standard deviation for both of the products along the flow direction through the straight pipe sections.However,both the Shannon entropy and standard deviation values tend to decrease after the flow through bend(s).This result could be attributed to the deceleration of particles while flowing through the bends,resulting in dampened particle fluctuation and turbulence.Lower values of Shannon entropy in the early parts of the pipeline could be due to the non-suspension nature of flow(dense-phase),i.e.,there is a higher probability that the particles are concentrated toward the bottom of pipe,compared with dilute-phase or suspension flow(high velocity),where the particles could be expected to be distributed homogenously throughout the pipe bore(as the flow is in suspension).Changes in straight-pipe pneumatic conveying characteristics along the flow direction also indicate a change in the flow regime along the flow.     

Predicting the mode of flow in pneumatic conveying systems-A review

An initial prediction of the particulate mode of flow in pneumatic conveying systems is beneficial as this knowledge can provide clearer direction to the pneumatic conveying design process.There are three general categories of modes of flow,two dense flows:fluidised dense phase and plug flow,and dilute phase only.Detailed in this paper is a review of the commonly used and available techniques for predicting mode of flow.Two types of predictive charts were defined:basic particle parameter based (e.g.particle size and density) and air-particle parameter based (e.g.permeability and de-aeration).The basic particle techniques were found to have strong and weak areas of predictive ability,on the basis of a comparison with data from materials with known mode of flow capability.It was found that there was only slight improvement in predictive ability when the particle density was replaced by loose-poured bulk density in the basic parameter techniques.The air-particle-parameter-based techniques also showed well-defined regions for mode of flow prediction though the data set used was smaller than that for the basic techniques.Also,it was found to be difficult to utilise de-aeration values from different researchers and subsequently,an air-particle-based technique was developed which does not require any de-aeration parameter in its assessment.     

Predicting the mode of flow in pneumatic conveying systems-- A review

An initial prediction of the particulate mode of flow in pneumatic conveying systems is beneficial as this knowledge can provide clearer direction to the pneumatic conveying design process. There are three general categories of modes of flow, two dense flows： fluidised dense phase and plug flow, and dilute phase oniy. Detailed in this paper is a review of the commonly used and available techniques for predicting mode of flow. Two types of predictive charts were defined： basic particle parameter based （e.g. particle size and density） and air-particle parameter based （e.g. permeability and de-aeration）. The basic particle techniques were found to have strong and weak areas of predictive ability, on the basis of a comparison with data from materials with known mode of flow capability. It was found that there was only slight improvement in predictive ability when the particle density was replaced by loose-poured bulk density in the basic parameter techniques. The air-particle-parameter-based techniques also showed well-defined regions for mode of flow prediction though the data set used was smaller than that for the basic techniques. Also, it was found to be difficult to utilise de-aeration values from different researchers and subsequently, an air-particle-based technique was developed which does not require any de-aeration parameter in its assessment.     

An investigation into flow mode transition and pressure fluctuations for fluidized dense-phase pneumatic conveying of fine powders

This paper presents the results of an ongoing investigation into the fluctuations of pressure signals due to solids–gas flows for dense-phase pneumatic conveying of fine powders. Pressure signals were obtained from pressure transducers installed along different locations of a pipeline for the fluidized dense-phase pneumatic conveying of fly ash (median particle diameter 30 μm; particle density 2300 kg/m³; loose-poured bulk density 700 kg/m³) and white powder (median particle diameter 55 μm; particle density 1600 kg/m³; loose-poured bulk density 620 kg/m³) from dilute to fluidized dense-phase. Standard deviation and Shannon entropy were employed to investigate the pressure signal fluctuations. It was found that there is an increase in the values of Shannon entropy and standard deviation for both of the products along the flow direction through the straight pipe sections. However, both the Shannon entropy and standard deviation values tend to decrease after the flow through bend(s). This result could be attributed to the deceleration of particles while flowing through the bends, resulting in dampened particle fluctuation and turbulence. Lower values of Shannon entropy in the early parts of the pipeline could be due to the non-suspension nature of flow (dense-phase), i.e., there is a higher probability that the particles are concentrated toward the bottom of pipe, compared with dilute-phase or suspension flow (high velocity), where the particles could be expected to be distributed homogenously throughout the pipe bore (as the flow is in suspension). Changes in straight-pipe pneumatic conveying characteristics along the flow direction also indicate a change in the flow regime along the flow.     

Energy loss at bends in the pneumatic conveying of fly ash

An accurate estimation of the total pressure drop of a pipeline is important to the reliable design of a pneumatic conveying system. The present paper presents results from an investigation into the modelling of the pressure drop at a bend in the pneumatic conveying of fly ash. Seven existing bend models were used (in conjunction with solids friction models for horizontal and vertical straight pipes, and initial acceleration losses) to predict the total pipeline pressure drop in conveying fly ash (median particle diameter: 30 μm; particle density: 2300 kg/m³; loose-poured bulk density: 700 kg/m³) in three test rigs (pipelines with dimensions of 69 mm inner diameter (I.D.) × 168 m length; 105 mm I.D. × 168 m length; 69 mm I.D. × 554 m length). A comparison of the pneumatic conveying characteristics (PCC) predicted using the seven bend models and experimental results shows that the predicted total pipeline PCC and trends depend on the choice of bend model. While some models predict trends that agree with the experimental results, other models predicted greater bend pressure drops for the dense phase of fly ash than for the dilute phase. Models of Pan, R. (1992). Improving scale-up procedures for the design of pneumatic conveying systems. Doctoral dissertation, University of Wollongong, Australia, Pan, R., & Wypych, P.W. (1998). Dilute and dense phase pneumatic conveying of fly ash. In Proceedings of the sixth International Conference on Bulk Materials Storage and Transportation (pp. 183–189), Wollongong, NSW, Australia and Chambers, A.J., & Marcus, R.D. (1986). Pneumatic conveying calculations. In Proceedings of the second International Conference on Bulk Materials Storage and Transportation (pp. 49–52), Wollongong, Australia reliably predicted the bend losses for systems conveying fly ash over a large range of air flows.     

Numerical study of coarse coal particle breakage in pneumatic conveying

Pneumatic conveying of coarse coal particles with various pipeline configurations and swirling intensities was investigated using a coupled computational fluid dynamics and discrete element method. A particle cluster agglomerated by the parallel-bond method was modeled to analyze the breakage of coarse coal particles. The numerical parameters, simulation conditions, and simulation results were experimentally validated. On analyzing total energy variation in the agglomerate during the breakage process, the results showed that downward fluctuation of the total particle energy was correlated with particle and wall collisions, and particle breakage showed a positive correlation with the energy difference. The correlation between the total energy variation of a particle cluster and particle breakage was also analyzed. Particle integrity presented a fluctuating upward trend with pipe bend radius and increased with swirling number for most bend radii. The degree of particle breakage differed with pipeline bending direction and swirling intensity: in a horizontal bend, the bend radius and swirling intensity dominated the total energy variations; these effects were not observed in a vertical bend. The total energy of the particle cluster exiting a bend was generally positively correlated with the bend radius for all conditions and was independent of bending direction.     

An experimental investigation into modeling solids friction for fluidized dense-phase pneumatic transport of powders

Results are presented of an ongoing investigation into modeling friction in fluidized dense-phase pneumatic transport of bulk solids. Many popular modeling methods of the solids friction use the dimensionless solids loading ratio and Froude number. When evaluated under proper scale-up conditions of pipe diameter and length, many of these models have resulted in significant inaccuracy. A technique for modeling solids friction has been developed using a new combination of dimensionless numbers, volumetric loading ratio and the ratio of particle free settling velocity to superficial conveying air velocity, to replace the solids loading ratio and Froude number. The models developed using the new formalism were evaluated for accuracy and stability under significant scale-up conditions for four different products conveyed through four different test rigs (subject to diameter and length scale-up conditions). The new model considerably improves predictions compared with those obtained using the existing model, especially in the dense-phase region. Whereas the latter yields absolute average relative errors varying between 10% and 86%, the former yielded results with errors from 4% to 20% for a wide range of scale-up conditions. This represents a more reliable and narrower range of prediction that is suitable for industrial scale-up requirements.     

Observations of “granular jump” in the pneumatic conveying system

This paper presents a preliminary study of a previously unreported phenomenon of the “gas driven granular jump”, observed in the gas–solids flow within the pneumatic conveying system. From the phenomenological point of view, it resembles the already known processes such as hydraulic jumps in shallow water or granular jumps in granular flows in chutes or avalanches (although it seems most appropriate to explain it by analogy to a propagating granular bore). Clearly, unlike in classical phenomena of this type, the flow itself is driven by the aerodynamic forces related to the gas flow and the behaviour of the front of the “jump” is modified significantly by their presence. A series of high-speed camera visualisations are presented, which focus on this unusual behaviour of the flow on the border-line between cluster and stratified flow regimes in a horizontal pipe. Some similarities are drawn between the observed phenomenon and the broader class of problems exhibiting transition between super- and sub-critical flows. The fluid dynamical aspects and possible mechanisms behind the new phenomenon are discussed and the results obtained are compared quantitatively with simple theoretical models.     

Experimental investigation into transient pressure pulses during pneumatic conveying of fine powders using Shannon entropy

This paper presents the results of an ongoing investigation into transient pressure pulses using Shannon entropy. Pressure fluctuations (produced by gas–solid two-phase flow during fluidized dense-phase conveying) are recorded by pressure transducers installed at strategic locations along a pipeline. This work validates previous work on identifying the flow mode from pressure signals (Mittal, Mallick, & Wypych, 2014). Two different powders, namely fly ash (median particle diameter 45 μm, particle density 1950 kg/m³, loosely poured bulk density 950 kg/m³) and cement (median particle diameter 15 μm, particle density 3060 kg/m³, loosely poured bulk density 1070 kg/m³), are conveyed through different pipelines (51 mm I.D. × 70 m length and 63 mm I.D. × 24 m length). The transient nature of pressure fluctuations (instead of steady-state behavior) is considered in investigating flow characteristics. Shannon entropy is found to increase along straight pipe sections for both solids and both pipelines. However, Shannon entropy decreases after a bend. A comparison of Shannon entropy among different ranges of superficial air velocity reveals that high Shannon entropy corresponds to very low velocities (i.e. 3–5 m/s) and very high velocities (i.e. 11–14 m/s) while low Shannon entropy corresponds to mid-range velocities (i.e. 6–8 m/s).     

A qualitative study on the pulsatile flow phenomenon in a dense fly ash pneumatic conveyor

Understanding of the dynamic particulate flow structures within a dense gas-fly ash pneumatic conveyor must be improved in order to better aid its design guidance.The complex pulsatile movement of the gas-fly ash mixture dominates the flow performance within the pipeline,and historically,non-invasive measurement devices such as the electrical capacitance tomography（ECT） were often used to sufficiently capture the flow dynamics.However,inadequate studies have been conducted on the pulsatile flow phenomenon,which directly relate to the gas-fly ash two-phase flow performance.This paper aims to investigate the pulsatile flows using an ECT device.Initially,pulsatile flow patterns under various experimental conditions were obtained through ECT.Pulses within a flow were then characterised into pulse growth and decay segments,which represent the superficial fluidisation and deaeration processes during conveying.Subsequently,structural and statistical analyses were performed on the pulse growth and decay segments.Results suggested that the increasing air mass flow rate led to the decrease of the superficial fluidisation/deaeration magnitude,however,the increase of the superficial fluidisation/deaeration durations.Also,the air mass flow rate was indicated as the dominant factor in determining the pulsing statistical parameters.This research provides fundamental insights for further modelling the dense fly ash pneumatic flows.     

Experimental study and modeling of particle drying in a continuously-operated horizontal fluidized bed

Multistage fluidized beds are frequently used for product drying in industry. One advantage of these fluidized beds is that they can achieve a high throughput, when operated continuously. In this study, γ-Al₂O₃ particles were dried in a pilot-scale horizontal fluidized bed, without considering any comminution effects. For each experiment, the particle moisture content distribution and residence time distribution were determined. To take into account particle back mixing in our experiments, a one-dimensional population balance model that considers particle residence time was introduced into a fluidized bed-drying model. Experimental particle residence time distributions were reproduced using a tank-in-series model. Subsequently, the moisture content distribution was implemented, as a second dimension to the population balance in this model. These two-dimensional simulations were able to describe the experimental data, especially the spread in the residual particle moisture distribution, much more accurately than one-dimensional simulations. Using this novel two-dimensional model, the effects of different operating parameters (process gas temperature, solid feed rate, superficial air velocity) on the particle moisture content distribution were systematically studied.     

Experimental study of compressible boundary layer on a cone at angles of attack

Experimental study was conducted for boundarylayers on a sharp 5° half-angle cone of 400mm length at angles of attack. The model was tested in the T-326 hypersonic wind tunnel （ITAM） at freestream Mach number M = 5.95. Mean and fluctuation wall characteristics of the boundary layer are measured at 0°, 2°, 3° and 4° angles of attack for different stagnation pressures. Pulsation measurements are carried out by means of ALTP sensor. Pressure and temperature distributions along the model are obtained, and transition beginning and end locations have been found. Boundary layer stabilization with the increase of angle of attack and the decrease of stagnation pressure is observed. High frequency pulsations inherent to hypersonic boundary layer （second mode） have been detected.     

Experimental study of heat and mass transfer from a horizontal cylinder in downward air-water mist flow with blockage effect

An experimental study was made on convective heat and mass transfer from a horizontal heated cylinder in a downward flow of air-water mist at a blockage ratio of 0.4. The measured local heat transfer coefficients agree fairly well with the authors' numerical solutions obtained previously for the front surface of a cylinder over the ranges mass flow ratio 0–4.5×10⁻², a temperature difference between the cylinder and air 10–43 K, gas Reynolds number (7.9–23)×10³, Rosin-Rammler size parameter 105–168 μm, and dispersion parameter 3.4–3.7. Heat transfer augmentation, two-pahse to single-phase of greater than 19 was attained at the forward stagnation point. For heat transfer in the rear part of the cylinder, an empirical formula is derived by taking into account the dimensionless governing variables, that is, coolant-feed and evaporation parameters.