Tetrakis Sn(IV) alkoxides as novel initiators for living ring‐opening polymerization of lactides

The use of tetrakis Sn(IV) alkoxides as highly active initiators for the ring‐opening polymerization of D ,L ‐lactide is reported. The activities of prepared Sn(IV) tetra‐2‐methyl‐2‐butoxide, Sn(IV) tetra‐iso‐propoxide, and Sn(IV) tetra‐ethoxide were compared to a well‐known ring‐opening polymerization initiator system, Sn(II) octoate activated with n‐butanol. All polymerizations were conducted at 75 °C in toluene. The activities of tetrakis Sn(IV) alkoxides grew in order of increasing steric hindrance, and the bulky Sn(IV) alkoxides showed higher activity than the Sn(II) octoate/butanol system. The living character of the polymerization was demonstrated in homopolymerization of D ,L ‐lactide and in block copolymerization of L ‐lactide with ?‐caprolactone. ¹H, ¹³C, and ¹¹⁹Sn NMR were used to characterize the prepared Sn(IV) alkoxides and the polymer microstructure, and size exclusion chromatography was used to determine the molar masses as well as the molar‐mass distributions of the polymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1901–1911, 2004     

Synthesis of cyclic poly(l‐lactide) catalyzed by Bismuth Salicylates—A combination of two drugs

l ‐lactide was polymerized in bulk at 160 or 180°C with mixtures of bismuth subsalicylate (BiSub) and salicylic (SA) as catalysts. The SA/Bi ratio and the monomer/Bi ratio were varied. The highest molecular weights (weight average, Mw) were achieved at a SA/Bi ratio of 1/1 (Mw up to 92 000 g mol^?1). l ‐Lactide was also polymerized with combinations of BiSub and silylated SA, and Mw values up to 120 000 g mol^?1 were achieved at 180°C. MALDI‐TOF mass spectrometry and Mark‐Houwink‐Sakurada measurements proved that under optimized reaction conditions the resulting polylactides consist of cycles. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2056–2063     

Ring‐opening polymerization of 6‐hydroxynon‐8‐enoic acid lactone: Novel biodegradable copolymers containing allyl pendent groups

This article reports the synthesis and copolymerization of 6‐hydroxynon‐8‐enoic acid lactone. The ring‐opening polymerization of this lactone‐type monomer bearing a pendant allyl group led to new homopolymers and random copolymers with ε‐caprolactone and L ,L ‐lactide. The copolymerizations were carried out at 110 °C with Sn(Oct)₂ as a catalyst. The introduction of unsaturations into the aliphatic polyester permitted us to carry out different chemical transformations on this family of polymers. For example, this article reports the bromination, epoxidation, and hydrosylilation of the allyl group in the new polyester copolymers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 870–875, 2000     

Synthesis of biodegradable thermoplastic elastomers from ε‐caprolactone and lactide

This article reports the synthesis and the properties of novel thermoplastic elastomers of A‐B‐A type triblock copolymer structure, where the hard segment A is poly(l ‐lactide) (PLLA) and the soft segment B is poly(ε‐caprolactone‐stat‐d ,l ‐lactide) (P(CL‐stat‐DLLA)). The P(CL‐stat‐DLLA) block with DLLA content of 30 mol % was applied because of its amorphous nature and low glass transition temperature (T_g = approximately ?40 °C). Successive polymerization of l ‐lactide afforded PLLA‐block‐P(CL‐stat‐DLLA)‐block‐PLLAs, which exhibited melting temperature (T_m = approximately 150 °C) for the crystalline PLLA segments and still low T_g (approximately ?30 °C) of the soft segments. The triblock copolymers showed very high elongation at break up to approximately 2800% and elastic properties. The corresponding d ‐triblock copolymers, PDLA‐block‐P(CL‐stat‐DLLA)‐block‐PDLAs (PDLA = poly(d ‐lactide)) were also prepared with the same procedure using d ‐lactide in place of l ‐lactide. When the PLLA‐block‐P(CL‐stat‐DLLA)‐block‐PLLA was blended with PDLA‐block‐P(CL‐stat‐DLLA)‐block‐PDLA, stereocomplex crystals were formed to enhance their T_m as well as tensile properties. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 489–495     

Simple route for synthesis of H‐shaped copolymers

The H‐shaped copolymers, [poly(L ‐lactide)]₂polystyrene [poly(L ‐lactide)]₂, [(PLLA)₂PSt(PLLA)₂] have been synthesized by combination of atom transfer radical polymerization (ATRP) with cationic ring‐opening polymerization (CROP). The first step of the synthesis is ATRP of St using α,α′‐dibromo‐p‐xylene/CuBr/2,2′‐bipyridine as initiating system, and then the PSt with two bromine groups at both chain ends (Br–PSt–Br) were transformed to four terminal hydroxyl groups via the reaction of Br–PSt–Br with diethanolamine in N,N‐dimethylformamide. The H‐shaped copolymers were produced by CROP of LLA, using PSt with four terminal hydroxyl groups as macroinitiator and Sn(Oct)₂ as catalyst. The copolymers obtained were characterized by ¹H NMR spectroscopy and gel permeation chromatography. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2794–2801, 2006     

Controllable ring‐opening copolymerization of L‐lactide and (3S)‐benzyloxymethyl‐(6S)‐methyl‐morpholine‐2,5‐dione initiated by a biogenic compound creatinine acetate

Ring‐opening copolymerization (ROCP) of L ‐lactide (L ‐LA) and (3S)‐benzyloxymethyl‐(6S)‐methyl‐morpholine‐2,5‐dione [(3S, 6S)‐BMMD] initiated by creatinine acetate, a biogenic organic compound, was performed in the bulk at 130 °C. The copolymerization was well controlled as evidenced by that both the measured values of number‐average molecular weight (M_n,NMR(OH) and M_n,NMR(COOH)) and serine molar fraction (F_Bz.ser) of synthesized copolymers were close to the corresponding theoretical values; and that the higher isotacticity of synthesized copolymers (85–86%) and lower racemization degree of the ROCP. After removing O‐benzyls of the copolymers with Et₃SiH/Et₃N/CH₂Cl₂ under catalysis of PdCl₂, functional biodegradable copolymers of L ‐lactic acid (L ‐Lac) and L ‐Ser with designed molar fraction of serine (F_ser 1.35%, 3.57%, 5.41%), narrow molecular weight distribution (polydispersity index 1.10–1.36), and improved hydrophilicity (θ_stat 82.3–89.6°) were finally obtained. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Polymerization kinetics of rac‐lactide initiated with alcohol/stannous octoate using in situ attenuated total reflectance‐fourier transform infrared spectroscopy: An initiator study

rac‐Lactide polymerization kinetics in THF at 72 °C were monitored in real‐time using mid‐infrared ATR‐FTIR spectroscopy, with diamond composite insertion probe and light conduit technology. Monomer concentration as a function of time was acquired using the 1240 cm^?1 resonance associated with the ? CO? O? C? stretch. Polymerizations were initiated with either n‐propanol (PrOH), ethylene glycol (EG), trimethylol propane (TMP), or pentaerythritol (PENTA) with the coinitiator stannous octoate (Sn(Oct)₂). Polymerizations were found to be reversible at high monomer conversions, with a residual monomer concentration at 72 °C (345 K) of 0.081 M. The polymerizations were internally first‐order with respect to monomer, indicating a constant concentration of propagating centers. For a typical reaction with [rac‐LA]₀ = 1.0 M, [PENTA]₀ = 1.3 × 10^?2 M, and [Sn(Oct)₂] = 2.5 × 10^?2 M, the first‐order rate constant, k_app was measured as 1.8 × 10^?4 s^?1. First‐order rate constants were determined to be independent of polymer architecture (i.e., initiator functionality) and proportional to [Sn(Oct)₂] for [Sn(Oct)₂]₀/[ROH]₀ ? 1, where [ROH]₀ represents the initial concentration of initiating hydroxyl groups. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 797–803, 2009     

Rapid Ring‐Opening Polymerization of D,L‐Lactide by Microwaves

Summary: Poly(D ,L ‐lactide) with a molar mass of 10⁵ g · mol⁻¹ and a yield over 90% was produced in 10 min by the ring‐opening polymerization of D ,L ‐lactide under microwave irradiation with forward power of 255 W. A degradation of the poly(D ,L ‐lactide) was also induced by microwaves with a power level over 340 W. The molar mass of poly(D ,L ‐lactide) was dependent upon the competition between the polymerization of D ,L ‐lactide and the degradation of the resulting polymer.

Profiles of molar mass versus microwave irradiation time (1.8 g DLLA, 0.1% Sn(Oct)₂).     

Controlled surface‐initiated ring‐opening polymerization of L‐lactide from risedronate‐anchored hydroxyapatite nanocrystals: Novel synthesis of biodegradable hydroxyapatite/poly(L‐lactide) nanocomposites

Risedronate‐anchored hydroxyapatite (HA‐RIS) nanocrystals were prepared with 4.1 wt % RIS and used for controlled surface‐initiated ring‐opening polymerization (ROP) of L ‐lactide (L ‐LA). The strong adsorption of RIS to HA surface not only led to enhanced dispersion of HA nanocrystals in water as well as in organic solvents but also provided alkanol groups as active initiating species for ROP of L ‐LA. HA‐RIS was characterized by thermogravimetric analysis, dynamic light scattering, ¹H NMR, Fourier transform infrared spectrometer, and X‐ray diffraction. The graft polymerization of L ‐LA onto HA‐RIS took place smoothly in the presence of stannous octoate in toluene at 120 °C, resulting in HA/poly(L ‐LA) nanocomposites with high yields of 85–90% and high poly(L ‐LA) contents of up to 97.5 wt %. Notably, differential scanning calorimetry measurements revealed that the poly(L ‐LA) in HA/poly(L ‐LA) nanocomposites exhibited considerably higher melting temperatures (T_m = 173.3?178.1 °C) and higher degrees of crystallinity (X_c = 41.0?43.1%) as compared to poly(L ‐LA) homopolymer (T_m = 168.5 °C, X_c =25.7%). In addition, our initial results showed that these HA/poly(L ‐LA) nanocomposites could readily be electrospun into porous matrices. This study presented a novel and controlled synthetic strategy to HA/RIS/poly(L ‐LA) nanocomposites that are promising for orthopedic applications as well as for bone tissue engineering. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Hyperbranched poly (amine‐ester)‐poly (lactide‐co‐glycolide) copolymer and their nanoparticles as paclitaxel delivery system

A new hyperbranched poly (amine‐ester)‐poly (lactide‐co‐glycolide) copolymer (HPAE‐co‐PLGA) was synthesized by ring‐opening polymerization of D , L ‐lactide (DLLA) glycolid and branched poly (amine‐ester) (HPAE‐OHs) with Sn(Oct)₂ as catalyst. The chemical structures of copolymers were determined by FT‐IR, ¹H‐NMR(¹³C NMR), TGA and their molecular weights were determined by gel permeation chromatography (GPC). Paclitaxel‐loaded copolymer nanoparticles were prepared by the nanoprecipitation method. Their physicochemical characteristics, e.g. morphology and nanoparticles size distribution were then evaluated by means of fluorescence spectroscopy, environmental scanning electron microscopy (ESEM), and dynamic light scattering (DLS). Paclitaxel‐loaded nanoparticles assumed a spherical shape and have unimodal size distribution. It was found that the chemical composition of the nanoparticles was a key factor in controlling nanoparticles size, drug‐loading content, and drug release behavior. As the molar ratio of DL ‐lactide/glycolide to HPAE increased, the nanoparticles size and drug‐loading content increased, and the drug release rate decreased. The antitumor activity of the paclitaxel‐loaded HPAE‐co‐PLGA nanoparticles against human liver cancer H7402 cells was evaluated by 3‐(4, 5‐dimethylthiazol‐2‐yl)‐2,5‐diphenyl tetrazolium bromide (MTT) method. The paclitaxel‐loaded HPAE‐co‐PLGA nanoparticles showed comparable anticancer efficacy with the free drug. Copyright © 2010 John Wiley & Sons, Ltd.     

Microwave‐assisted synthesis and characterization of biodegradable block copolyesters based on poly(3‐hydroxyalkanoate)s and poly(D,L‐lactide)

Microwave (MW)‐assisted ring‐opening polymerization (ROP) provides a rapid and straightforward method for engineering a wide array of well‐defined poly(3‐hydroxyalkanoate)‐b‐poly(D,L ‐lactide) (PHA‐b‐PLA) diblock copolymers. On MW irradiation, the bulk ROP of D,L ‐lactide (LA) could be efficiently triggered by a series of monohydroxylated PHA‐based macroinitiators previously produced via acid‐catalyzed methanolysis of corresponding native PHAs, thus affording diblock copolyesters with tunable compositions. The dependence of LA polymerization on temperature, macroinitiator structure, irradiation time, and [LA]₀/[PHA]₀ molar ratio was carefully investigated. It turned out that initiator efficiency values close to 1 associated with conversions ranging from 50 to 85% were obtained only after 5 min at 115 °C. A kinetic investigation of the MW‐assisted ROP of LA gave evidence of its “living”/controlled character under the experimental conditions selected. Structural analyses and thermal properties of biodegradable diblock copolyesters were also performed. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

In situ formation of Sn(IV) catalyst with increased activity in ε‐caprolactone and L‐lactide polymerization using stannous(II) 2‐ethylhexanoate

Ring‐opening polymerization (ROP) of ε‐caprolactone and L‐lactide (LA) was studied using stannous(II) 2‐ethylhexanoate (Sn(Oct)₂) with N,N‐dimethylformamide‐dimethyl acetal (DMF‐DMA). DMF‐DMA showed a tenfold improvement in catalytic activity over that of Sn(Oct)₂ under the same conditions. It also enhanced the capability to control molecular weight in the synthesis of small molecular weight polymers of polycaprolactone and polylactide (PLA). The high molecular weight polymerization demonstrated a strong capability to control molecular weight for the polymerization of LA: a molecular weight of PLA exceeding 400,000 was obtained at very low catalytic loadings. The individual polymerization rates of other tin reagents with DMF‐DMA also clearly increased. Applying this methodology could drastically reduce the time and cost required for the fabrication of these products to increase the competitive advantage of manufacturers. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Kinetics and mechanism of cyclic esters polymerisation initiated with tin(II) octoate, 4. Influence of proton trapping agents on the kinetics of ε‐caprolactone and L,L‐dilactide polymerisation

Kinetics of the polymerisation of ε‐caprolactone and L ,L ‐dilactide initiated with tin(II) 2‐ethylhexanoate (tin octoate (Sn(Oct)₂)) and carried out in the presence of 2,6‐di‐tert‐butylpyridine ( 1 ) and/or 1,8‐bis(dimethylamino)naphthalene ( 2 ), in THF as the solvent, at 80°C was studied. The rate of polymerisation of the cyclic ester in the presence of 1 or 2 , known to be a “proton trap” or “proton sponge”, respectively, is either practically the same or even exceeds that of the polymerisation conducted in the absence of these hindered amines. Consequently, the proposed earlier mechanisms of polymerisation of cyclic esters coinitiated by Sn(Oct)₂, with chain growth involving active species with “protons”, i. e. primary or secondary oxonium ions, have to be put on rest. This includes also the mechanism in which propagation was proposed to proceed within a ternary complex consisting of hydroxyl group terminated macromolecule, Sn(Oct)₂, and a cyclic ester monomer. The observed final increase of the rate of polymerization is in agreement with the interconversion previously decribed by us: Sn(Oct)₂ + ROH ⇌ OctSnOR + OctH since OctH (a carboxylic acid) is becoming complexed with a proton trap/sponge and the concentration of OctSnOR (the actual initiator) is effectively increased.     

Synthesis of star‐shaped poly(D,L‐lactic acid‐alt‐glycolic acid)‐b‐poly(L‐lactic acid) with the poly(D,L‐lactic acid‐alt‐glycolic acid) macroinitiator and stannous octoate catalyst

Two types of three‐arm and four‐arm, star‐shaped poly(D,L ‐lactic acid‐alt‐glycolic acid)‐b‐poly(L ‐lactic acid) (D,L ‐PLGA50‐b‐PLLA) were successfully synthesized via the sequential ring‐opening polymerization of D,L ‐3‐methylglycolide (MG) and L ‐lactide (L ‐LA) with a multifunctional initiator, such as trimethylolpropane and pentaerythritol, and stannous octoate (SnOct₂) as a catalyst. Star‐shaped, hydroxy‐terminated poly(D,L ‐lactic acid‐alt‐glycolic acid) (D,L ‐PLGA50) obtained from the polymerization of MG was used as a macroinitiator to initiate the block polymerization of L ‐LA with the SnOct₂ catalyst in bulk at 130 °C. For the polymerization of L ‐LA with the three‐arm, star‐shaped D,L ‐PLGA50 macroinitiator (number‐average molecular weight = 6800) and the SnOct₂ catalyst, the molecular weight of the resulting D,L ‐PLGA50‐b‐PLLA polymer linearly increased from 12,600 to 27,400 with the increasing molar ratio (1:1 to 3:1) of L ‐LA to MG, and the molecular weight distribution was rather narrow (weight‐average molecular weight/number‐average molecular weight = 1.09–1.15). The ¹H NMR spectrum of the D,L ‐PLGA50‐b‐PLLA block copolymer showed that the molecular weight and unit composition of the block copolymer were controlled by the molar ratio of L ‐LA to the macroinitiator. The ¹³C NMR spectrum of the block copolymer clearly showed its diblock structures, that is, D,L ‐PLGA50 as the first block and poly(L ‐lactic acid) as the second block. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 409–415, 2002     

Synthesis and properties of cationic ionomers from poly(ester‐urethane)s based on polylactide

l ‐Lactide (l ‐LA) was polymerized in the presence of N‐methyldiethanolamine as an initiator and Sn(Oct)₂ as a catalyst to give hydroxy‐telechelic poly(l ‐lactide) (PLLA‐diol) bearing a tertiary amine group at the center of the polymer chain. Successive chain extension of the PLLA‐diol with hexamethylene diisocyanate afforded PLLA‐based poly(ester‐urethane)s (PEU) with equally spaced tertiary amine groups. Treatment of the PEU with iodomethane converted tertiary amine groups to quaternary ammonium groups to give cationic ionomers (PEU‐MeI). The thermal, mechanical, hydrophilic, and biodegradation properties of the obtained polymers were investigated. The thermal properties of the PEUs and the PEU‐MeIs were similar each other. The PEU‐MeIs exhibited higher tensile modulus than those of the starting PEUs. The contact angles of water on the PEU‐MeIs were lower than those of the PEUs with similar NMDA content indicating their higher hydrophilicity. In compost degradation tests, the PEU‐MeIs showed slower degradation than those of the PEUs. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4423–4428     

Synthesis and characterization of poly(L‐lactide)s and poly(D‐lactide)s of controlled molecular weight

High molecular weight poly(L ‐lactide)s (PLLAs) and poly(D ‐lactide)s (PDLAs) were synthesized in toluene at 70 °C by ring‐opening polymerization of optically pure L ‐lactide and D ‐lactide, using tin(II) 2‐ethylhexanoate (SnOct₂) and 2‐(2‐methoxyethoxy)ethanol as initiator and coinitiator, respectively. Under these conditions, polarimetry as well as ¹³C NMR spectroscopy indicated that the synthesized poly(lactide)s (PLAs) are more than 99% isotactic. The molecular weight was successfully controlled by adjusting the monomer‐to‐initiator molar ratio. Gel permeation chromatography and MALDI‐TOF mass spectrometry analyses showed that the polydispersity index of the PLAs is below 1.1. Moreover, MALDI‐TOF spectra showed two different chain distributions, one characterized by an even number of lactic acid repeat units and the other by an odd number of lactic acid repeat units. The second distribution, indicative of the presence of intermolecular transesterification reactions, appears at the very beginning of the polymerization and its intensity increases with the polymerization time. Finally, a reversible reaction kinetic model was used to determine the monomer equilibrium concentration ([M]_eq = 1.4 ± 0.5%) and the propagation rate constant (k_p = 14.4 ± 0.5 L mol^?1 h^?1) of the polymerization. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1944–1955, 2007     

Living polymerization of D,L‐3‐methylglycolide initiated with bimetallic (Al/Zn) μ‐oxo alkoxide and copolymers thereof

D,L ‐3‐Methylglycolide (MG) was successfully polymerized with bimetallic (Al/Zn) μ‐oxo alkoxide as an initiator in toluene at 90 °C. The effect of the initiator concentration and monomer conversion on the molecular weight was studied. It is shown that the polymerization of MG follows a living process. A kinetic study indicated that the polymerization approximates the first order in the monomer, and no induction period was observed. ¹H NMR spectroscopy showed that the ring‐opening polymerization proceeds through a coordination–insertion mechanism with selective cleavage of the acyl–oxygen bond of the monomer. On the basis of ¹H NMR and ¹³C NMR analyses, the selective cleavage of the acyl–oxygen bond of the monomer mainly occurs at the least hindered carbonyl groups (P₁ = 0.84, P₂ = 0.16). Therefore, the main chain of poly(D,L ‐lactic acid‐co‐glycolic acid) (50/50 molar ratio) obtained from the homopolymerization of MG was primarily composed of alternating lactyl and glycolyl units. The diblock copolymers poly(ϵ‐caprolactone)‐b‐poly(D,L ‐lactic acid‐alt‐glycolic acid) and poly(L ‐lactide)‐b‐poly(D,L ‐lactic acid‐alt‐glycolic acid) were successfully synthesized by the sequential living polymerization of related lactones (ϵ‐caprolactone or L ‐lactide). ¹³C NMR spectra of diblock copolymers clearly show their pure diblock structures. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 357–367, 2001     

Ring‐opening polymerization of cyclic esters promoted by phosphido‐diphosphine pincer group 3 complexes

Phosphido‐diphosphine Group 3 metal complexes 1–4 [(o‐C₆H₄PR₂)₂P‐M(CH₂SiMe₃)₂; R = Ph, 1 : M = Y, 2 : M = Sc; R = iPr, 3 : M = Y, 4 : M = Sc] are very efficient catalysts for the ring‐opening polymerization (ROP) of cyclic esters such as ε‐caprolactone (ε‐CL), L ‐lactide, and δ‐valerolactone under mild polymerization conditions. In the ROP of ε‐CL, complexes 1–4 promote quantitative conversion of high amount of monomer (up to 3000 equiv) with very high turnover frequencies (TOF) (～4 × 10⁴ mol_CL/mol_I h) showing a catalytic activity among the highest reported in the literature. The immortal and living ROP of ε‐CL and L ‐lactide is feasible by combining complexes 1–4 with 5 equiv of 2‐propanol. Polymers with controlled molecular parameters (M_n, end groups) and low polydispersities (M_w/M_n = 1.05–1.09) are formed as a result of fast alkoxide/alcohol exchange. In the ROP of δ‐valerolactone, complexes 1–4 showed the same activity observed for lactide (L ‐ and D ,L ‐lactide) producing high molecular weight polymers with narrow distribution of molar masses. Complexes 1–4 also promote the ROP of rac‐β butyrolactone affording atactic low molecular weight poly(hydroxybutyrate) bearing unsaturated end groups probably generated by elimination reactions. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthetic and Mechanistic Aspects of the Immortal Ring‐Opening Polymerization of Lactide and Trimethylene Carbonate with New Homo‐ and Heteroleptic Tin(II)‐Phenolate Catalysts

Several new heteroleptic Sn^II complexes supported by amino‐ether phenolate ligands [Sn{LOⁿ}(Nu)] (LO¹=2‐[(1,4,7,10‐tetraoxa‐13‐azacyclopentadecan‐13‐yl)methyl]‐4,6‐di‐tert‐butylphenolate, Nu=NMe₂ ( 1 ), N(SiMe₃)₂ ( 3 ), OSiPh₃ ( 6 ); LO²=2,4‐di‐tert‐butyl‐6‐(morpholinomethyl)phenolate, Nu=N(SiMe₃)₂ ( 7 ), OSiPh₃ ( 8 )) and the homoleptic Sn{LO¹}₂ ( 2 ) have been synthesized. The alkoxy derivatives [Sn{LO¹}(OR)] (OR=OiPr ( 4 ), (S)‐OCH(CH₃)CO₂iPr ( 5 )), which were generated by alcoholysis of the parent amido precursor, were stable in solution but could not be isolated. [Sn{LO¹}]⁺[H₂N{B(C₆F₅)₃}₂]^? ( 9 ), a rare well‐defined, solvent‐free tin cation, was prepared in high yield. The X‐ray crystal structures of compounds 3 , 6 , and 8 were elucidated, and compounds 3 , 6 , 8 , and 9 were further characterized by ¹¹⁹Sn Mössbauer spectroscopy. In the presence of iPrOH, compounds 1 – 5 , 7 , and 9 catalyzed the well‐controlled, immortal ring‐opening polymerization (iROP) of L ‐lactide (L ‐LA) with high activities (ca. 150–550 mol_L?LA mol_Sn^?1 h^?1) for tin(II) complexes. The cationic compound 9 required a higher temperature (100 °C) than the neutral species (60 °C); monodisperse poly(L ‐LA)s were obtained in all cases. The activities of the heteroleptic pre‐catalysts 1 , 3 , and 7 were virtually independent of the nature of the ancillary ligand, and, most strikingly, the homoleptic complex 2 was equally competent as a pre‐catalyst. Polymerization of trimethylene carbonate (TMC) occurs much more slowly, and not at all in the presence of LA; therefore, the generation of PLA‐PTMC copolymers is only possible if TMC is polymerized first. Mechanistic studies based on ¹H and ¹¹⁹Sn{¹H} NMR spectroscopy showed that the addition of an excess of iPrOH to compound 3 yielded a mixture of compound 4 , compound [Sn(OiPr)₂]_n 10 , and free {LO¹}H in a dynamic temperature‐dependent and concentration‐dependent equilibrium. Upon further addition of L ‐LA, two active species were detected, [Sn{LO¹}(OPLLA)] ( 12 ) and [Sn(OPLLA)₂] ( 14 ), which were also in fast equilibrium. Based on assignment of the ¹¹⁹Sn{¹H} NMR spectrum, all of the species present in the ROP reaction were identified; starting from either the heteroleptic ( 1 , 3 , 7 ) or homoleptic ( 2 ) pre‐catalysts, both types of pre‐catalysts yielded the same active species. The catalytic inactivity of the siloxy derivative 6 confirmed that ROP catalysts of the type 1 – 5 could not operate according to an activated‐monomer mechanism. These mechanistic studies removed a number of ambiguities regarding the mechanism of the (i)ROPs of L ‐LA and TMC promoted by industrially relevant homoleptic or heteroleptic Sn^II species.     

Efficient zinc initiators supported by NNO‐tridentate ketiminate ligands for cyclic esters polymerization

A series of zinc benzylalkoxide complexes, [LⁿZn(μ‐OBn)]₂ (L = L ¹ H – L ⁵ H ), supported by NNO‐tridentate ketiminate ligands with various electron withdrawing‐donating subsituents have been synthesized and characterized. X‐ray crystal structural studies revealed that complexes 2b and 4b are dinuclear bridging through the benzylalkoxy oxygen atoms with penta‐coordinated metal centers. All the metal complexes have acted as efficient initiators for the ring‐opening polymerization of L ‐lactide (within 12 min, 0 °C). Remarkably, a molecular weight of PLLA up to 580,000 can be achieved using [(L⁵Zn(μ‐OBn)]₂ ( 5b ) as an initiator. The kinetic studies for the polymerization of L ‐lactide with complex 3b at ?10 °C corresponded to first‐order reactions in the monomer. The ring‐opening polymerization (ROP) of ε‐caprolactone, ε‐decalactone, β‐butyrolactone and their copolymer with complex 3b was investigated. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013