Capillary liquid chromatography-microchip atmospheric pressure chemical ionization-mass spectrometry

A miniaturized nebulizer chip for capillary liquid chromatography-atmospheric pressure chemical ionization-mass spectrometry (capillary LC-microchip APCI-MS) is presented. The APCI chip consists of two wafers, a silicon wafer and a Pyrex glass wafer. The silicon wafer has a DRIE etched through-wafer nebulizer gas inlet, an edge capillary insertion channel, a stopper, a vaporizer channel and a nozzle. The platinum heater electrode and pads for electrical connection were patterned on to the Pyrex glass wafer. The two wafers were joined by anodic bonding, creating a microchip version of an APCI-source. The sample inlet capillary from an LC column is directly connected to the vaporizer channel of the APCI chip. The etched nozzle in the microchip forms a narrow sample plume, which is ionized by an external corona needle, and the formed ions are analyzed by a mass spectrometer. The nebulizer chip enables for the first time the use of low flow rate separation techniques with APCI-MS. The performance of capillary LC-microchip APCI-MS was tested with selected neurosteroids. The capillary LC-microchip APCI-MS provides quantitative repeatability and good linearity. The limits of detection (LOD) with a signal-to-noise ratio (S/N) of 3 in MS/MS mode for the selected neurosteroids were 20-1000 fmol (10-500 nmol l(-1)). LODs (S/N = 3) with commercial macro APCI with the same compounds using the same MS were about 10 times higher. Fast heat transfer allows the use of the optimized temperature for each compound during an LC run. The microchip APCI-source provides a convenient and easy method to combine capillary LC to any API-MS equipped with an APCI source. The advantages and potentials of the microchip APCI also make it a very attractive interface in microfluidic APCI-MS.     

Atmospheric pressure thermospray ionization using a heated microchip nebulizer

When a standard atmospheric pressure chemical ionization (APCI) or atmospheric pressure photoionization (APPI) ion source is used without applying the corona discharge or photoirradiation, atmospheric pressure thermospray ionization (APTSI) of various compounds can be achieved. Although largely ignored, this phenomenon has recently gained interest as an alternative ionization technique. In this study, this technique is performed for the first time on a miniaturized scale using a microchip nebulizer. Sample ionization with the presented microchip‐APTSI (µAPTSI) is achieved by applying only heat and gas flow to a nebulizer chip, without any other methods to promote gas‐phase ionization. To evaluate the performance of the described µAPTSI setup, ionization efficiency for a set of test compounds was monitored as the microchip positioning, temperature, nebulizer gas flow rate, sample solution composition, and solvent flow rate were varied. The µAPTSI mass spectra of the test compounds were also compared to those obtained with ESI and APCI. The µAPTSI produces ESI‐like spectra with low background noise, favoring the formation of protonated or deprotonated molecules of compounds that are ionizable in solution. Multiple charging of peptides without in‐source fragmentation was also observed. Unlike ESI, however, the µAPTSI source can tolerate the presence of mobile phase additives like trifluoroacetic acid (TFA) without significant ion suppression. The µAPTSI source can be used with standard mass spectrometer ion source hardware, being a unique alternative to the present interfacing techniques. Copyright © 2009 John Wiley & Sons, Ltd.     

Characterization of the atmospheric pressure ionization mass spectrometric process obtained using a fused-silica emitter with the high voltage applied upstream

The atmospheric pressure ionization process obtained when a mixture of methanol and water (90:10, v/v) also containing 50 microM sodium hydroxide is dispersed from a fused-silica emitter was studied. A combination of a high electric field and a nebulizer gas with the high voltage applied upstream in the liquid flow was utilized to facilitate the spray process. By comparing the dependences of the spray current and ion signals on the spray potential, it was found that electrical corona discharges were obtained for potentials higher than about 2.6 kV, which resulted in a mixed electrospray and chemical ionization process. By introducing vapour from a solvent, such as benzene or toluene, with a low ionization energy into the nebulizing gas, it was found that the appearance of the corresponding molecular ion was correlated with a change in the slope of the spray current-potential curve. This indicates that the breakpoints in the spray current-potential curves observed were correlated with the onsets of corona discharges. It was shown that the mixed ionization process gives rise to increased amounts of protonated solvent molecules and assists in the formation of sodiated adduct ions from an uncharged fatty acid methyl ester.     

Temperature‐programmed capillary high‐performance liquid chromatography with atmospheric pressure chemical ionization mass spectrometry for analysis of fatty acid methyl esters

A new capillary high‐performance liquid chromatography method with atmospheric pressure chemical ionization mass spectrometry was developed for the analysis of fatty acid methyl esters and long‐chain alcohols. The chromatographic separation was achieved using a Zorbax SB‐C18 HPLC column (0.3 × 150 mm, 3.5 μm) with a mobile phase composed of acetonitrile and formic acid and delivered isocratically at a flow rate of 10 μL/min. The column temperature was programmed simply, using a common column oven. Good reproducibility of the temperature profile and retention times were achieved. The temperature programming during the isocratic high‐performance liquid chromatography run had a similar effect as a solvent gradient; it reduced retention times of later eluting analytes and improved their detection limits. Two atmospheric pressure chemical ionization sources of the mass spectrometry detector were compared: an enclosed conventional ion source and an in‐house made ion source with a glass microchip nebulizer. The enclosed source provided better detectability of saturated fatty acid methyl esters and made it possible to determine the double bond positions using acetonitrile‐related adducts, while the open chip‐based source provided better analytical figures of merit for unsaturated fatty acid methyl esters. Temperature‐programmed capillary high‐performance liquid chromatography is a promising method for analyzing neutral lipids in lipidomics and other applications.     

An electropneumatic‐heated nebulizer for enhancing spray ionization in PhotoSpray atmospheric pressure photoionization sources for liquid chromatography/mass spectrometry

We introduce a novel electropneumatic‐heated nebulizer (EPn‐HN), incorporating an electrified internal pneumatic nebulizer, to enhance the yield of sprayed ions from PhotoSpray? atmospheric pressure photoionization (APPI) sources for liquid chromatography/mass spectrometry (LC/MS). Spray ionization from the pneumatic‐heated nebulizers used in APPI sources provides a supplemental, complementary ionization method to be used for involatile and thermally labile compounds, otherwise intractable to APPI. Details of the construction and operation of the EPn‐HN device are provided. The performance of the EPn‐HN is demonstrated using two model compounds: substance P, a peptide used as a standard in studies of ion fragmentation mechanisms, and aztreonam, a thermally labile antibiotic. At the optimum voltage for spray ionization, improvements in sensitivity of two orders of magnitude are obtained relative to when the sprayer is grounded, the conventional case. Since both substance P and aztreonam cannot be detected using the APPI method alone, the results demonstrate how spray ionization from the EPn‐HN may be used to extend the range of compounds amenable to PhotoSpray sources. Copyright © 2009 John Wiley & Sons, Ltd.     

Feasibility of gas chromatography-microchip atmospheric pressure photoionization-mass spectrometry in analysis of anabolic steroids

Mass spectrometers equipped with atmospheric pressure ion sources (API-MS) have been designed to be interfaced with liquid chromatographs (LC) and have rarely been connected to gas chromatographs (GC). Recently, we introduced a heated nebulizer microchip and showed its potential to interface liquid microseparation techniques and GC with API-MS. This study demonstrates the feasibility of GC-microchip atmospheric pressure photoionization-tandem mass spectrometry (GC-μAPPI-MS/MS) in the analysis of underivatized anabolic steroids in urine. The APPI microchip provides high ionization efficiency and produces abundant protonated molecules or molecular ions with minimal fragmentation. The feasibility of GC-μAPPI-MS/MS in the analysis of six selected anabolic steroids in urine samples was studied with respect to intra-batch repeatability, linearity, linear range, and limit of detection (LOD). The method showed good sensitivity (LODs 0.2-1 ng/mL), repeatability (relative standard deviation<10%), and linearity (regression coefficient≥0.9995) and, therefore, high potential for the analysis of anabolic steroids. Quantitative performance of the method was tested with two authentic urine samples, and the results were in good agreement with those obtained with conventional GC-electron ionization-MS after derivatization.     

Integrated liquid chromatography-heated nebulizer microchip for mass spectrometry

A new integrated microchip for liquid chromatography-mass spectrometry (LC-MS) is presented. The chip is made from bonded silicon and glass wafers with structures for a packed LC column channel, a micropillar frit, a channel for optional optical detection, and a heated vaporizer section etched in silicon and platinum heater elements on the glass cover. LC eluent is vaporized and mixed with nebulizer gas in the vaporizer section and the vapor is sprayed out from the chip. Nonpolar and polar analytes can be efficiently ionized in the gas phase by atmospheric pressure photoionization (APPI) as demonstrated with polycyclic aromatic hydrocarbons (PAHs) and selective androgen receptor modulators (SARMs). This is not achievable with present LC-MS chips, since they are based on electrospray ionization, which is not able to ionize nonpolar compounds efficiently. The preliminary quantitative performance of the new chip was evaluated in terms of limit of detection (down to 5 ng mL⁻¹), linearity (r > 0.999), and repeatability of signal response (RSD = 2.6-4.0%) and retention time (RSD = 0.3-0.5%) using APPI for ionization and PAHs as standard compounds. Determination of fluorescent compounds is demonstrated by using laser-induced fluorescence (LIF) for detection in the optical detection channel before the vaporizer section.     

An overview of LC–MS interfacing systems with selected applications

Advantages and limitations are described for the different LC–MS interfacing systems (moving belt; direct liquid introduction; thermospray; atmospheric pressure ionization with heated pneumatic nebulizer, electrospray, or high flow ion spray; particle beam; and continuous flow fast atom bombardment). Some comments are also made about interfacing capillary zone electrophoresis (CZE). The peculiarities of the various interfaces are described, as are liquid chromatographic requirements prior to mass spectrometry using the different ionization techniques. Selected biological and environmental applications are given.     

A microfabricated micropillar liquid chromatographic chip monolithically integrated with an electrospray ionization tip

We present the first monolithically integrated silicon/glass liquid chromatography-electrospray ionization microchip for mass spectrometry. The microchip is fabricated by bonding a silicon wafer, which has deep reactive ion etched micropillar-filled channels, together with a glass lid. Both the silicon channel and the glass lid have a through-wafer etched sharp tip that produces a stable electrospray. The microchip is also compatible with laser induced fluorescence (LIF) detection, due to the glass lid. Separation of drugs in less than 5 minutes using either SiO(2) (normal phase) or C(18) coated (reversed-phase) pillars with good sensitivity was demonstrated with mass spectrometric detection as well as separation of fluorescent compounds with LIF detection.     

Continuous full filling capillary electrochromatography-electrospraying chromatographic nanoparticles

The influence of instrumental parameters affecting the ionization in continuous full filling capillary electrochromatography/electrospray ionization mass spectrometry (CFF‐CEC/ESI‐MS) was investigated. The investigated parameters were the BGE and sheath liquid ion strength and organic modifier content, the nebulizer gas pressure, and the concentration of nanoparticles in the BGE. It was found that the nebulizer pressure had the largest influence on the separation efficiency and apparent retention. It was shown that even the lowest pressure investigated was sufficient to guide the nanoparticle flow away from the mass spectrometer inlet. A nebulizer pressure of 5 psi was found to be optimal; increasing the pressure significantly decreased the separation efficiency due to the generation of a hydrodynamic flow. Generally, the ion strength of both the BGE and the sheath liquid were found to have very moderate effects on the separation of a homologous series of dialkyl phthalates, whereas the ionization efficiency was found to be unaffected by the nanoparticles and the separation efficiency was found to increase with increasing concentrations up to 3.8 mg/mL, whereafter it was observed to drop. The optimized method was linear over a wide concentration range and presented LOD and LOQ more than threefold lower than those previously reported using CFF‐CEC/ESI‐MS.     

Incorporation of a flared inlet capillary tube on a Fourier transform ion cyclotron resonance mass spectrometer

Flared inlet capillary tubes have been coupled with a Fourier transform ion cyclotron resonance (FT-ICR) mass spectrometer to help the ion transmission from the atmospheric pressure to the first vacuum region. We investigated different types of atmospheric pressure ionization methods using flared inlet tubes. For most of the ionization methods, such as ESI and DESI, increased ion current transmitted from the atmospheric pressure ion source to the first stage vacuum system was observed with the use of our enhanced ion inlet designs. The corresponding ion intensity detected on a FT-ICR mass spectrometer was also observed to increase two- to fivefold using ESI or DESI with the flared tube inlet. Moreover, increased spray tip positional tolerance was observed with implementation of the flared inlet tube. We also include our preliminary results obtained by coupling AP-MALDI with flared inlet tube in this paper. For AP-MALDI, the measured ion current transferred through the flared inlet tube was about 2 to 3 times larger than the ion current through the control non-flared inlet tube.     

Modeling of ion processes in atmospheric pressure matrix-assisted laser desorption/ionisation

Atmospheric pressure matrix-assisted laser desorption/ionization (AP-MALDI) has proven a convenient and rapid method for ion production in the mass spectrometric analysis of biomolecules. This technique, like other atmospheric pressure ionization methods, suffers from ion loss during ion transmission from the atmosphere into the vacuum of the mass spectrometer. In this work, a simple model describing ion formation and ion motion towards the inlet capillary of the mass spectrometer is described. Both the gas flow and electric field near the MALDI plate were numerically calculated using the boundary element method (BEM). The ions were moving along with the gas flow and drifting in the electric field in accordance with their ion mobility properties. The ion signal dependence on an electric field strength obtained in the proposed model correlates well with experimental results.     

Desorption electrospray ionization mass spectrometry of DNA nucleobases: implications for a liquid film model

Desorption electrospray ionization (DESI) mass spectrometry has been implemented on a commercial ion‐trap mass spectrometer and used to optimize mass spectrometric conditions for DNA nucleobases: adenine, cytosine, thymine, and guanine. Experimental parameters including spray voltage, distance between mass spectrometer inlet and the sampled spot, and nebulizing gas inlet pressure were optimized. Cluster ions including some magic number clusters of nucleobases were observed for the first time using DESI mass spectrometry. The formation of the cluster species was found to vary with the nucleobases, acidification of the spray solvent, and the deposited sample amount. All the experimental results can be explained well using a liquid film model based on the two‐step droplet pick‐up mechanism. It is further suggested that solubility of the analytes in the spray solvent is an important factor to consider for their studies by using DESI. Copyright © 2009 John Wiley & Sons, Ltd.     

Atmospheric pressure ionization and liquid chromatography/mass spectrometry—together at last

The evolution of atmospheric pressure ionization techniques which are now routinely applied as liquid chromatograph/mass spectrometer (LC/MS) interfaces is described. Electrospray and related methods, as well as atmospheric pressure chemical ionization combined with the heated nebulizer interface, both began as specialized ionization techniques which became much more widely accepted when combined with tandem mass spectrometry. Today, both are widely used for quantitative and qualitative LC/MS and LC/MS/MS analyses. Important events in the development of these methods are described, along with key elements in the evolution of the ion source-to-vacuum interface techniques that contributed to their success.     

On the mechanism of ion formation from the aqueous solutions irradiated with 3 microm IR laser pulses under atmospheric pressure

The mechanism of atmospheric pressure (AP) laser ionization of water and water/glycerol liquid samples at a 3-microm wavelength is studied experimentally. For the ion desorption, an in-house built Yb : YAG-pumped optical parametric oscillator (OPO) infrared (IR) laser has been coupled with AP MALDI ion source interfaced to an ion trap mass spectrometer (MS). It has been shown that water is primarily responsible for ion generation in water/glycerol samples, while glycerol increases the solution viscosity and decreases the water evaporation rate and sample losses. In contrast to AP UV-MALDI, the electric field in the case of AP IR-MALDI does not assist in ion production. It was found that the absence of the electrical field provides the optimum ionization condition both for water and water/glycerol liquid samples at the 3-microm laser irradiation. A two-stage ion formation mechanism, which includes the initial emission of microdroplets and release of molecular ions at the second stage, can explain the experimentally observed ion signal dependencies upon the voltage applied between MS inlet and the MALDI sample plate. Postionization using additional corona discharge APCI increases the observed signal by approximately 50%, which indicates that some portion of the analyte is desorbed in the form of neutral molecules.     

Limitations and perspectives in the determination of carbofuran with various liquid chromatography-mass spectrometry interfacing systems

Column liquid chromatography with mass spectrometric detection (LC-MS) has been widely accepted as the preferred technique for the identification and quantification of polar and thermally labile compounds at trace levels. Over the last decade many different types of LC-MS interfacing techniques have been used for the determination of carbamate pesticides and especially for the N-methylcarbamate carbofuran. This article addresses the difficulties encountered with the various types of LC-MS interface and discusses recent alternatives for the determination of carbofuran. With thermospray and particle beam interfaces the quantification of carbofuran is affected by both the ion source pressure and temperature, whereas quantification using the recently developed atmospheric pressure ionization interfaces, atmospheric pressure chemical ionization, electrospray, and ionspray, is less dependent on these parameters.     

An evaluation of atmospheric pressure ionization techniques for the analysis of N-Methyl carbamate pesticides by liquid chromatography mass spectrometry

Atmospheric pressure ionization (API) techniques are evaluated for the mass spectral analysis of N-methyl carbamate pesticides. Atmospheric pressure chemical ionization (APCI) using a heated nebulizer interface provided both protonated molecules and abundant, characteristic fragment ions. With ion spray (ISP; pneumatically assisted electrospray ionization), which utilizes a milder “ion evaporation” process, primarily protonated molecules were obtained, although fragment ions similar to those observed in APCI could be induced by variation of the API orifice voltage. Product ion spectra of ISP-derived protonated molecules, generated by tandem mass spectrometry using collision-induced dissociation, are also presented. The APCI and ISP spectra of the carbamates are compared to those obtained with a thermospray interface and also to their electron ionization and methane CI spectra obtained with a particle beam interface. For all four interfaces, combined liquid chromatography mass spectrometry methods using conventional (4.6 mm i.d.) columns are described for the separation and detection of pesticide mixtures. These methods are applied to the confirmatory analysis of three representative carbamate pesticides, spiked at the 0.1-ppm level in green peppers. For those carbamates amenable to gas chromatography mass spectrometry, comparative results are presented.     

An atmospheric pressure ion lens that improves nebulizer assisted electrospray ion sources

An atmospheric pressure ion lens improves the performance and ease of use of a nebulizer assisted electrospray (ion spray) ion source. The lens is comprised of an oblong-shaped stainless steel ring attached to an external high voltage power supply. The lens is located near the tip of the conductive sprayer, and is maintained at a potential less than that of the sprayer. The ion lens improves the shape of the equipotential lines in the vicinity of the sprayer tip. This lens gives approximately a 2-fold reduction in the signal RSD, a 2-fold increase in the ion signal, an increase in the number of multiply charged ions, and a much broader range of usable sprayer positions.     

Comparison of thermospray and ion spray mass spectrometry in an atmospheric pressure ion source

Ion spray is an approach to liquid chromatography, mass spectrometry which includes features common to the electrospray and ion evaporation interfaces. Thermospray is a liquid chromatographic/mass spectrometric technique which utilizes heat and electrolytes in the mobile phase to generate sample ions. In this paper the operation of these two techniques at atmospheric pressure are compared with respect to the effects of solvent composition and electrolyte ion concentration for the production of ions from compounds that are ionized in solution (safranin orange, acid black 1 and testosterone sulfate) and un-ionized in solution (methyl red, adenosine and diethylstilbestrol). The results indicate that at atmospheric pressure ion spray produces ions by the ion evaporation mechanism while thermospray produces ions by both gas-phase chemical ionization and ion evaporation processes.     

An atmospheric pressure ionization source based on desorption electrospray ionization technology (DESI) for ion cyclotron resonance mass spectrometry

An atmospheric pressure ionization source based on desorption electrospray ionization technology for a bench-top hybrid FTICR mass spectrometer is described. The ion source was characterized using low-molecular-weight-weight pharmaceutical samples. The dependences of signal intensities on various experimental parameters (solvent composition, surface temperature, spray voltage, etc.) were studied. Based on the results obtained, plausible mechanisms of desorption electrospray ionization for the analytes under the study are discussed.