Atomistic insights on the LCST behavior of PMEO2MA in water by molecular dynamics simulations

Fully atomistic molecular dynamics simulations of poly(2‐[2‐methoxyethoxy]ethyl methacrylate) (PMEO₂MA) in water at temperatures below and above its lower critical solution temperature (LCST) were performed to improve the understanding of its LCST behavior. Atomic trajectories were used to calculate various structural and dynamic properties. Simulation results show that PMEO₂MA undergo a distinct coil‐to‐globule transition above LCST. Detailed analyses of the number of first hydration shell water molecules around various atomic regions are revealed that the water solubility of PMEO₂MA below LCST is mainly provided by the hydrophobic hydration around the side chain carbon atoms. This is achieved by the cage‐like water network formations which are disrupted when the temperature is increased above LCST, accompanied by significant amount of water molecule release and local water‐ordering reduction, which leads to the LCST phase transition. Furthermore, other analyses such as the number of hydrogen bonds and hydrogen bond lifetimes suggest that intermolecular hydrogen bondings between polymer and water molecules have little effect on the phase transition. Our results will contribute to a better understanding on the LCST phase transition of oligo(ethylene glycol) methyl ether methacrylate (OEGMA)‐based homopolymers at atomistic level that will be useful when designing homo‐ and co‐polymers of OEGMAs with desired properties. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 429–441     

Temperature‐sensitive hyperbranched poly(glycidol)s with oligo(ethylene glycol) monoethers

Temperature‐dependent polymers are intelligent materials. In this study, biocompatible and temperature‐dependent hyperbranched poly(glycidol)s (HPGs) were synthesized and characterized. HPGs were succinylated then modified with the oligo(ethylene glycol) monoethers (OEG) for example methoxy di(ethylene glycol), methoxy tri(ethylene glycol), methoxy tetra(ethylene glycol), ethoxy di(ethylene glycol), ethoxy tri(ethylene glycol), and methoxy poly(ethylene glycol)s at different ratios. These polymers exhibited phase transitions at a specific temperature (the cloud point), depending on the composition of OEG. By tuning the composition of OEG in the polymer, thermosensitive polymers with cloud point near body temperature were produced. Endothermic peaks of these polymers were observed in the vicinity of the cloud point. It is suggested that at temperatures below the cloud point the polymers formed hydrophobic shells and became more hydrophobic at temperatures above the cloud point. Because they exhibited no cytotoxicity, these temperature‐sensitive polymers are useful for biomedical applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4047–4054, 2010     

Synthesis and characterization of novel degradable photocrosslinked poly(ether‐anhydride) networks

New degradable poly(ether‐anhydride) networks were synthesized by UV photopolymerization. Dicarboxylated poly(ethylene glycol) (PEG) or poly(tetramethylene glycol) (PTMG) was reacted with an excess of methacrylic anhydride to form dimethacrylated macromers containing anhydride linkages. The percent of conversion for the macromer formation was more than 80% at 60 °C after 24 h. ¹H NMR and IR spectroscopies show the presence of anhydride linkages in the macromer. In vitro degradation studies were carried out at 37 °C in PBS with crosslinked polymer networks formed by UV irradiation. All PEG‐based polymers degraded within 2 days, while PTMG‐based polymers degraded by 50% of the initial weight after 14 days. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1277–1282, 2000     

Water‐soluble,thermoresponsive, hyperbranched copolymers based on PEG‐methacrylates: Synthesis,characterization, and LCST behavior

A series of water‐soluble thermoresponsive hyperbranched copoly(oligoethylene glycol)s were synthesized by copolymerization of di(ethylene glycol) methacrylate (DEG‐MA) and oligo(ethylene glycol) methacrylate (OEG‐MA, M_w = 475 g/mol), with ethylene glycol dimethacrylate (EGD‐MA) used as the crosslinker, via reversible addition fragmentation chain transfer polymerization. Polymers were characterized by size exclusion chromatography and nuclear magnetic resonance analyses. According to the monomer composition, that is, the ratio of OEG‐MA: DEG‐MA: EGD‐MA, the lower critical solution temperature (LCST) could be tuned from 25 °C to 90 °C. The thermoresponsive properties of these hyperbranched copolymers were studied carefully and compared with their linear analogs. It was found that molecular architecture influences thermoresponsive behavior, with a decrease of around 5–10 °C in the LCST of the hyperbranched polymers compared with the LCST of linear chains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2783–2792, 2010     

Structural/compositional nanoheterogeneity and glass‐transition plurality in amorphous polycyanurate–poly(tetramethylene glycol) hybrid networks

The nanostructure and dynamics over the temperature range of ?140 to 300 °C were studied in a series of polycyanurate (PCN)–poly(tetramethylene glycol) (PTMG) hybrid networks by wide‐angle X‐ray diffraction and small‐angle X‐ray scattering, with a synchrotron radiation setup, and by differential scanning calorimetry (DSC) and laser‐interferometric creep rate spectroscopy (CRS) techniques, respectively. The networks were synthesized from the dicyanate ester of bisphenol A and hydroxyl‐terminated PTMG with a number‐average molecular weight of 1.000 g/mol; the PTMG content varied from 0 to 40 wt %, and the degree of its chemical incorporation into the PCN network changed from 78.8 to 97%. The noncrystalline structure and considerable structural nanoheterogeneity of the hybrid networks were shown. CRS/DSC analysis revealed a complicated dynamic behavior, that is, a wide dispersion of glass transitions in the hybrid networks due to the presence of nanodomains with different degrees of rigid crosslinking (i.e., compositional nanoheterogeneity). Besides the physical significance, the plurality of glass transitions found in the PCN–PTMG hybrid networks was also of practical interest because it resulted in increasing mechanical strength of the brittle PCN network due to microplasticity arising at room temperature and moderate temperatures and the retention of some rigidity and creep resistance at temperatures much higher than the basic glass‐transition temperature. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3261–3272, 2005     

Molecular design of outermost surface functionalized thermoresponsive polymeric micelles with biodegradable cores

We prepared well‐defined diblock copolymers of thermoresponsive poly(N‐isopropylacrylamide‐co‐N,N‐dimethylacrylamide) blocks and biodegradable poly(D ,L ‐lactide) blocks by combination of reversible addition‐fragmentation chain transfer radical (RAFT) polymerization and ring‐opening polymerization. α‐Hydroxyl, ω‐dithiobenzoate thermoresponsive polymers were synthesized by RAFT polymerization using hydroxyl RAFT agents. Biodegradable blocks were prepared by ring‐opening polymerization of D ,L ‐lactide initiated by α‐hydroxyl groups of thermoresponsive polymers, which inhibit the thermal decomposition of ω‐dithioester groups. Terminal dithiobenzoate (DTBz) groups of thermoresponsive blocks were easily reduced to thiol groups and reacted with maleimide (Mal). In aqueous media, diblock copolymer products formed surface‐functionalized thermoresponsive micelles. These polymeric micelles had a low critical micelle concentration of 22 μg/L. In thermoresponsive studies of the micelles, hydrophobic DTBz‐surface micelles demonstrated a significant shift in lower critical solution temperature (LCST) to a lower temperature of 30.7 °C than that for Mal‐surface micelles (40.0 °C). In addition, micellar LCST was controlled by changing bulk mixture ratios of respective heterogeneous end‐functional diblock copolymers. Micellar disruption at acidic condition (pH 5.0) was completed within 5 days due to hydrolytic degradation of PLA cores, regardless of showing a slow disruption rate at physiological condition. Furthermore, we successfully improved water‐solubility of hydrophobic drug, paclitaxel by incorporating into the micellar cores. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7127–7137, 2008     

Synthesis of poly[N‐isopropylacrylamide‐g‐poly(ethylene glycol)] with a reactive group at the poly(ethylene glycol) end and its thermosensitive self‐assembling character

Poly[N‐isopropylacrylamide‐g‐poly(ethylene glycol)]s with a reactive group at the poly(ethylene glycol) (PEG) end were synthesized by the radical copolymerization of N‐isopropylacrylamide with a PEG macromonomer having an acetal group at one end and a methacryloyl group at the other chain end. The temperature dependence of the aqueous solutions of the obtained graft copolymers was estimated by light scattering measurements. The intensity of the light scattering from aqueous polymer solutions increased with increasing temperature. In particular, at temperatures above 40°C, the intensity abruptly increased, indicating a phase separation of the graft copolymer due to the lower critical solution temperature (LCST) of the poly(N‐isopropylacrylamide) segment. No turbidity was observed even above the LCST, and this suggested a nanoscale self‐assembling structure of the graft copolymer. The dynamic light scattering measurements confirmed that the size of the aggregate was in the range of several tens of nanometers. The acetal group at the end of the PEG graft chain was easily converted to the aldehyde group by an acid treatment, which was analyzed by ¹H NMR. Such a temperature‐induced nanosphere possessing reactive PEG tethered chains on the surface is promising for new nanobased biomedical materials. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1457–1469, 2006     

Dispersion of polystyrene inside polystyrene‐b‐poly(N‐isopropylacrylamide) micelles in water

The addition of mixture of polystyrene‐b‐poly(N‐isopropylacrylamide) (PS‐b‐PNIPAM) and polystyrene homopolymer (h‐PS) in tetrahydrofuran dropwise into water leads to nanoparticles with a PS core and a thermally sensitive PNIPAM shell. The effects of the ratio of the homopolymer to copolymer and temperature on the formation and stabilization of the dispersion were investigated by using a combination of static and dynamic laser light scattering. PNIPAM shell continuously collapses as temperature increases in the range 20–40 °C. Such formed particles are stable even at temperatures much higher than lower critical solution temperature (LCST ～ 32 °C) of PNIPAM. Our results reveal that the area occupied per hydrophilic PNIPAM chain on the hydrophobic PS core remains nearly a constant regardless of the amount of h‐PS in the polymer mixture. This clearly indicates that the surface area occupied per hydrophilic group is a critical parameter for stabilizing particles dispersed in water. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 749–755, 2010     

Synthesis and self‐association behavior of poly[bis(2‐(2‐methoxyethoxy)ethoxy)phosphazene]‐b‐poly(propyleneglycol) triblock copolymers

Amphilic triblock copolymers with varying ratios of hydrophilic poly[bis (methoxyethoxyethoxy)phosphazene] (MEEP) and relatively hydrophobic poly(propylene glycol) (PPG) blocks were synthesized via the controlled cationic‐induced living polymerization of a phosphoranimine (Cl₃P?NSiMe₃) at ambient temperature. A PPG block can function as either a classical hydrophobic block or a less hydrophobic component by varying the nature of a phosphazene block. The aqueous phase behavior of MEEP‐PPG‐MEEP block copolymers was investigated using fluorescence techniques, TEM, and dynamic light scattering (DLS). The critical micelle concentrations (cmcs) of MEEP‐PPG‐MEEP block copolymers were determined to be in the range of 3.7–16.8 mg/L. The mean diameters of MEEP‐PPG‐MEEP polymeric micelles, measured by DLS, were between 31 and 44 nm. The equilibrium constants of pyrene in these micelles ranged from 4.7 × 10⁴ to 9.6 × 10⁴. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 692–699, 2009     

Heterogeneity of glass transition dynamics in polyurethane‐poly(2‐hydroxyethyl methacrylate) semi‐interpenetrating polymer networks

The peculiarities of segmental dynamics over the temperature range of ?140 to 180 °C were studied in polyurethane‐poly(2‐hydroxyethyl methacrylate) semi‐interpenetrating polymer networks (PU‐PHEMA semi‐IPNs) with two‐phase, nanoheterogeneous structure. The networks were synthesized by the sequential method when the PU network was obtained from poly(oxypropylene glycol) (PPG) and adduct of trimethylolpropane (TMP) and toluylene diisocyanate (TDI), and then swollen with 2‐hydroxyethyl methacrylate monomer with its subsequent photopolymerization. PHEMA content in the semi‐IPNs varied from 10 to 57 wt %. Laser‐interferometric creep rate spectroscopy (CRS), supplemented with differential scanning calorimetry (DSC), was used for discrete dynamic analysis of these IPNs. The effects of anomalous, large broadening of the PHEMA glass transition to higher temperatures in comparison with that of neat PHEMA, despite much lower T_g of the PU constituent, and the pronounced heterogeneity of glass transition dynamics were found in these networks. Up to 3 or 4 overlapping creep rate peaks, characterizing different segmental dynamics modes, have been registered within both PU and PHEMA glass transitions in these semi‐IPNs. On the whole, the united semi‐IPN glass transition ranged virtually from ?60 to 160 °C. As proved by IR spectra, some hybridization of the semi‐IPN constituents took place, and therefore the effects observed could be properly interpreted in the framework of the notion of “constrained dynamics.” The peculiar segmental dynamics in the semi‐IPNs studied may help in developing advanced biomedical, damping, and membrane materials based thereon. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 963–975, 2007     

UCST and LCST phase behavior of poly(trimethylene ether) glycol in water

We describe the initial studies of the complex aqueous phase behavior of poly(trimethylene ether) glycol (PO3G), a renewably sourced polyether glycol. Cloud point measurement revealed that a low molecular weight PO3G exhibits both lower critical solution temperature (LCST) and upper critical solution temperature (UCST) in water in the temperature range between 30°C and 80°C. At low concentrations of PO3G, the polymer solutions exhibit LCST‐type phase behavior. In the intermediate concentration ranges, PO3G and water are immiscible. However, at higher concentrations of PO3G, the solutions show UCST‐type phase behavior. In addition, both the LCSTs and UCSTs can be easily tuned over a wide range by varying the amount of alcohol co‐solvents. These findings have potential applications in the design of personal care applications and in the development of thermosensitive “smart” materials. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Unified model of association-induced lower critical solution temperature phase separation and its application to solutions of telechelic poly(ethylene oxide) and of telechelic poly(N-isopropylacrylamide) in water

The authors present a model describing the coexistence of hydrophobic association and phase separation with lower critical solution temperature (LCST) in aqueous solutions of polymers carrying short hydrophobic chains at both chain ends (telechelic associating polymers). The LCST of these solutions is found to decrease along the sol/gel transition curve as a result of both end-chain association (association-induced phase separation) and direct hydrophobic interaction of the end chains with water. The authors relate the magnitude of the LCST decrease to a hydration cooperativity parameter sigma. The LCST decreases substantially (approximately 100 K) in the case of random hydration (sigma=1), whereas only a small shift (approximately 5-10 K) occurs in the case of cooperative hydration (sigma=0.3). The molecular weight dependence of the LCST drop is studied in detail in each case. The results are compared with experimental observations of the cloud points of telechelic poly(ethylene oxide) solutions, in which random hydration predominates, and of telechelic poly(N-isopropylacrylamide) solutions, in which cooperative hydration prevails.     

Shape memory biomaterials prepared from polyurethane/ureas containing sulfated glucose

Covalently crosslinked polyurethane/urea polymers were synthesized using diamine monomers modified with pendant glucose groups and 2,4‐toluene diisocyanate, poly(ethylene glycol) (PEG), and 1,1,1‐tris(hydroxymethyl)ethane (triol) comonomers. The polymers showed shape memory behavior with a switching temperature dependent on the glass transition temperature. The glass transition temperature is tuned by varying the mole ratio between the glucose‐diamine and PEG used in the polymerization. Increasing PEG content resulted in decreasing glass transition temperature, and a glass transition temperature of 39 °C, close to physiological temperatures, was obtained. The fixed shape showed gradual shape recovery behavior, but a fixity of 70% was achieved when the material was stored at 25 °C. The polymer recovered to the permanent shape when heated to 50 °C. Finally, the surface of a film of the polymer can be sulfated to achieve increased blood‐compatibility without sacrificing the shape memory properties. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2252–2257     

Doubly photoresponsive and water‐soluble block copolymers: Synthesis and thermosensitivity

We report the synthesis and investigation of a new type of photoresponsive block copolymers (BCPs). They were designed to comprise two water‐soluble polymers containing two different photoisomerizable moieties (either azobenzene and spiropyran or two different azobenzenes), with the two constituting blocks that, when separated, exhibit a lower critical solution temperature (LCST) in water and can shift their LCST in opposite directions upon photoisomerization (decrease of LCST for one polymer and increase for the other). A variety of such doubly photoresponsive BCPs were synthesized using either azobenzene‐ or spiropyran‐containing poly(N,N‐dimethylacrylamide) (PDMA), poly(N‐isopropylacrylamide) (PNIPAM) and poly[methoxydi(ethylene glycol) methacrylate] (PDEGMMA). Their thermal phase transition behaviors in aqueous solution before and after simultaneous photoreactions on the two blocks were investigated in comparison with their constituting blocks, by means of solution transmittance (turbidity) and variable‐temperature ¹H NMR measurements. The results show that BCPs displayed a single LCST whose shift upon two photoisomerizations appeared to be determined by the competing and opposing photoinduced effects on the two blocks. Moreover, optically controlling the relative photoisomerization degrees of trans azobenzene‐to‐cis azobenzene and spiropyran‐to‐merocyanine could be used to tune the LCST of BCP solution. This study demonstrates the potential of exploring a more complex photoreaction scheme to optically control the solution properties of water‐soluble thermosensitive BCPs. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4055–4066, 2010     

Synthesis and characterization of novel thermoresponsive‐co‐biodegradable hydrogels composed of N‐isopropylacrylamide,poly(L‐lactic acid), and dextran

A series of novel multifunctional hydrogels that combined the merits of both thermoresponsive and biodegradable polymeric materials were designed, synthesized, and characterized. The hydrogels were copolymeric networks composed of N‐isopropylacrylamide (NIPAAM) as a thermoresponsive component, poly(L‐lactic acid) (PLLA) as a hydrolytically degradable and hydrophobic component, and dextran as an enzymatically degradable and hydrophilic component. The chemical structures of the hydrogels were characterized by an attenuated total reflection–Fourier transform infrared spectroscopy (ATR–FTIR) technique. The hydrogels were thermoresponsive, showing a lower critical solution temperature (LCST) at approximately 32 °C, and their swelling properties strongly depended on temperature changes, the balance of the hydrophilic/hydrophobic components, and the degradation of the PLLA component. The degradation of the hydrogels caused by hydrolytic cleavage of ester bonds in the PLLA component was faster at 25 °C below the LCST than at 37 °C above the LCST, determined by the ATR–FTIR technique. Due to their multifunctional properties, the designed hydrogels show great potential for biomedical applications, including drug delivery and tissue engineering. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5054–5066, 2004     

XPS and ATR surface studies of block copolyurethanes based on 1,2-ethylene bis(4-phenyl isocyanate)

The surface properties of two block copolyurethanes based on 1,2-ethylene bis(4-phenyl isocyanate) (P2PDI), poly(tetramethylene ether glycol) (PTMG) or poly(propylene glycol) (PPG), and ethylene diamine, were investigated by attenuated total reflectance (ATR) infrared spectroscopy and X-ray photoelectron spectroscopy (XPS) analysis. The air-facing surfaces (AFS) of both materials are more abundant in the PPG or PTMG soft segment. More PTMG present on AFS indicates that the PTMG soft segment is more hydrophobic than PPG. Besides, the ATR spectra revealed that more phase mixing occurs in the near-surface region than in the bulk and the domain/matrix interface tends to orient to this region for both samples.     

Novel thermo‐responsive self‐assembly micelles from a double brush‐shaped PNIPAM‐g‐(PA‐b‐PEG‐b‐PA)‐g‐PNIPAM block copolymer with PNIPAM polymers as side chains

A novel double brush‐shaped copolymer with amphiphilic polyacrylate‐b‐poly(ethylene glycol)‐b‐poly acrylate copolymer (PA‐b‐PEG‐b‐PA) as a backbone and thermosensitive poly(N‐isopropylacrylamide) (PNIPAM) long side chains at both ends of the PEG was synthesized via an atom transfer radical polymerization (ATRP) route, and the structure was confirmed by FTIR, ¹H NMR, and SEC. The thermosensitive self‐assembly behavior was examined via UV‐vis, TEM, DLS, and surface tension measurements, etc. The self‐assembled micelles, with low critical solution temperatures (LCST) of 34–38 ^°C, form irregular fusiform and/or spherical morphologies with single, double, and petaling cores in aqueous solution at room temperature, while above the LCST the micelles took on more regular and smooth spherical shapes with diameter ranges from 45 to 100 nm. The micelle exhibits high stabilities even in simulated physiological media, with low critical micellization concentration (CMC) up to 5.50, 4.89, and 5.05 mg L^?1 in aqueous solution, pH 1.4 and 7.4 PBS solutions, respectively. The TEM and DLS determination reveled that the copolymer micelle had broad size distribution below its LCST while it produces narrow and homogeneous size above the LCST. The cytotoxicity was investigated by MTT assays to elucidate the application potential of the as‐prepared block polymer brushes as drug controlled release vehicles. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Thermoregulated phase‐transfer catalysis via PEG‐armed Ru(II)‐bearing microgel core star polymers: Efficient and reusable Ru(II) catalysts for aqueous transfer hydrogenation of ketones

Thermoregulated phase‐transfer catalysis for the transfer hydrogenation of 2‐octanone in 2‐propanol/H₂O biphasic media was achieved with ruthenium‐bearing microgel‐core star polymers with amphiphilic, thermosensitive poly(ethylene glycol) (PEG) arms [Ru(II)‐PEG star], which were directly prepared by the ruthenium‐catalyzed living radical polymerization in conjunction with a phosphine ligand‐carrying styrene derivative. The star polymers were first placed in the aqueous (lower) layer at room temperature and immediately moved into the organic (upper) layer at 100 °C, and once again, moved down to the aqueous layer (lower) upon cooling the solution to room temperature. The Ru(II)‐PEG star catalyst was clearly superior to the original Ru(II) catalyst and related non‐microgel catalysts [Ru(II)‐PEG block] in terms of activity and recovery/recycle, due to the unique designer structure of the microgel‐core star polymers. Other substrates (less hydrophobic alkyl ketones and aromatic ketone) were also efficiently hydrogenated into the corresponding sec‐alcohols with the star catalyst in aqueous media. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 373–379, 2010     

Poly(n‐alkylsilsesquioxane)s: Synthesis,characterization, and modification with poly(dimethylsiloxane)

Self‐supported translucent films constituted of poly(n‐octylsilsesquioxane) or poly(n‐dodecylsilsesquioxane) were obtained from the hydrolysis and condensation of n‐octyltriethoxysilane (OTES) or n‐dodecyltriethoxysilane (DTES), respectively. Dense films were obtained in the absence of organic solvents, with dibutyltin diacetate as catalyst. These films exhibited good optical transparency and thermal stability. The incorporation of oligomeric dimethylsiloxane units (D^Me,Me) in these materials, derived from silanol‐terminated poly(dimethylsiloxane) (PDMS) or 1,1,3,3‐tetramethyl‐1,3‐diethoxydisiloxane (TMDES), was carried out during the hydrolysis and condensation of OTES and DTES and was confirmed by solid‐state ²⁹Si NMR. Poly(n‐octylsilsesquioxane) showed a glass‐transition temperature at ?65 °C, due to the increase in the free volume, promoted by the bulky n‐octyl groups. The differential scanning calorimetric (DSC) curves of the polymer derived from DTES were characterized by first‐order transitions at temperatures ranging from ?15.8 to ?0.7 °C. Further studies of these networks by low‐temperature XRD evidenced narrowing of the diffraction halos suggesting a partial order–disorder transition for these materials at lower temperatures. Good thermal stability up to 350 °C and the solvent‐free production process make these polymers potential candidates for the development of self‐supported hydrophobic protective coatings. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1220–1229, 2010     

Hierarchically organized micellization of thermoresponsive rod‐coil copolymers based on poly[oligo(ethylene glycol) methacrylate] and poly(ε‐caprolactone)

A series of amphiphilic triblock copolymers, poly[oligo(ethylene glycol) methacrylate]_x‐block‐poly(ε‐caprolactone)‐block‐poly[oligo(ethylene glycol) methacrylate]_x, POEGMA_Co(x), were synthesized. Formation of hydrophobic domains as cores of the micelles was studied by fluorescence spectroscopy. The critical micelle concentrations in aqueous solution were found to be in the range of circa 10^?6 M. A novel methodology by modulated temperature differential scanning calorimetry was developed to determine critical micelle temperature. A significant concentration dependence of cmt was found. Dynamic light scattering measurements showed a bidispersed size distribution. The micelles showed reversible dispersion/aggregation in response to temperature cycles with lower critical solution temperature between 75 and 85 °C. The interplay of the two hydrophobic and one thermoresponsive macromolecular chains offers the chance to more complex morphologies. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010