Surface oxidation process of a diamond‐like carbon film analyzed by difference X‐ray photoelectron spectroscopy

Difference X‐ray photoelectron spectroscopy (D‐XPS) revealed the surface oxidation process of a diamond‐like carbon (DLC) film. Evaluation of surface functional groups on DLC solely by the C 1s spectrum is difficult because the spectrum is broad and has a secondary asymmetric lineshape. D‐XPS clarified the subtle but critical changes at the DLC surface caused by wet oxidation. The hydroxyl (C―OH) group was dominant at the oxidized surface. Further oxidized carbonyl (C?O) and carboxyl (including carboxylate) (COO) groups were also obtained; however, the oxidation of C?O to COO was suppressed to some extent because the reaction required C―C bond cleavage. Wet oxidation cleaved the aliphatic hydrogenated and non‐hydrogenated sp² carbon bonds (C―H sp² and C―C sp²) to create a pair of C―OH and hydrogenated sp³ carbon (C―H sp³) bonds. The reaction yield for C―H sp² was superior at the surface, suggesting that the DLC film was hydrogen rich at the surface. Oxidation of aromatic sp² rings or polycyclic aromatic hydrocarbons such as nanographite to phenols did not occur because of their resonance stabilization with electron delocalization. Non‐hydrogenated sp³ carbon (C―C sp³) bonds were not affected by oxidation, suggesting that these bonds are chemically inert. Copyright © 2014 John Wiley & Sons, Ltd.     

The high‐temperature tribological properties of Si‐DLC films

The tribological properties of Silicon‐containing diamond‐like‐carbon (Si‐DLC) films, deposited by magnetron sputtering Si target in methane/argon atmosphere, were studied in comparison with diamond‐like‐carbon (DLC) films. The DLC films disappeared because of the oxidation in the air at 500 °C, whereas the Si‐DLC films still remained, implying that the addition of Si improved significantly the thermal stability of DLC films. Retarded hydrogen release from DLC film at high temperature and silicon oxide on the surface might have contributed to lower friction coefficient of the Si‐DLC films both after annealing treatment and in situ high‐temperature environment. Copyright © 2012 John Wiley & Sons, Ltd.     

Ag/Au Alloy LSPR Engineering by Co‐deposition of RF‐Sputtering and RF‐PECVD

Silver‐Gold alloy/diamond like carbon (Ag‐Au/DLC) nanocomposite films were prepared by co‐deposition of RF‐sputtering and RF‐PECVD on glass substrates by using acetylene gas and silver‐gold target. The deposition process was carried out at room temperature in one minute with the variable parameters of initial pressures and RF powers. X‐ray diffraction analysis demonstrated the formation of Ag/Au alloy nanoparticles with a face‐centered cubic (FCC) structure. Localized surface plasmon and optical properties of Ag‐Au alloy nanoparticles were studied by UV‐visible spectrophotometry which showed that increasing RF power and initial pressure cause a redshift in all samples. Moreover, the effect of RF power and initial pressure on the size and shape of nanoparticles were studied by 2D Atomic force microscopy images. Energy dispersive X‐ray spectroscopy revealed the formation of Ag‐Au/DLC nanoparticles and the percentages of C, Ag, Au and O in all samples. The applied method for Ag/Au alloy preparation is the one step and low‐cost method which makes the samples ready for sensing application.     

Quantitative XPS analysis of hydrosilated 1‐alkene and 1‐alkyne at terraced,dihydrogen‐terminated, 1 × 1 (100) silicon

A quantitative angle‐resolved XPS analysis was carried out of the carbonaceous films resulting from the derivatization under mild thermal activation of nearly flat, terraced, dihydrogen‐terminated, 1 × 1 (100) Si with 1‐octene or 1‐octyne. The analysis of the C 1s signal gave evidence for the presence of carbon in carbide configuration (Si? C bonds) at the substrate–film interface, in addition to the alkanic carbon and adventitious oxidized carbon (C? O bonds) produced by the oxidizing impurities flawing the reaction. Assuming the surface as uniformly covered, the analysis showed that for both reactants the films were closely packed. Copyright © 2006 John Wiley & Sons, Ltd.     

Surface (XPS,SIMS) chemical investigation on poly(pyrrole‐3‐acetic acid) films electrosynthesized on Ti and TiAlV substrates for the development of new bioactive substrates

Electropolymerization of pyrrole‐3‐acetic acid was performed by cyclic voltammetry on titanium and Ti90Al6V4 substrates with the aim of developing a multilayer structure for applications in advanced biomaterials. The polymeric films obtained were characterized by both XPS and time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS). Information on the poly(pyrrole‐3‐acetic acid) (PPy‐3‐acetic) surface structure was achieved by a detailed XPS analysis of C 1s and N 1s signals. The number of COOH groups was quantified by XPS coupled to a chemical derivatization reaction in which esterification with trifluoroethanol was exploited so that the presence of fluorine (or the CF₃ component in C 1s spectra) could be used as a marker for COOH groups. As a result, it was found that more than 90% of the monomer units along PPy‐3‐acetic chains bear carboxylic functionalities, of which 60% are protonated and 40% are present as carboxylate groups. Some decarboxylation occurs with film ageing. The PPy‐3‐acetic films were also investigated by ToF‐SIMS in the negative ion mode, thus obtaining, for the first time, interesting information on the structure of the top surface layers of a polymer belonging to the polypyrrole family. In particular, clusters of peaks related to PPy‐3‐acetic oligomers were detected and the decarboxylation phenomenon on top of the polymer surface was confirmed. Copyright © 2005 John Wiley & Sons, Ltd.     

Carbon‐ion implantation improves the tribological properties of Co?Cr?Mo alloy against ultra‐high molecular weight polyethylene

Amorphous diamond‐like carbon (DLC) has drawn a great deal of attention for its superior wear properties against ultra‐high molecular weight polyethylene (UHMWPE). Its rate of wear, however, is not necessarily maintained within a specific range. The aim of this study was to evaluate the mechanical features and tribological properties of three types of surfaces: (i) uncoated, (ii) carbon‐ion implantation (CII)‐treated, and (iii) DLC‐film‐coated substrate. The surface alterations were carried out on cobalt–chrome (Co? Cr? Mo) alloy by the plasma‐source ion implantation (PSII) method. The wear properties and friction coefficient were estimated by a pin‐on‐plate wear‐tester. We found, as a result, that the implanted carbon penetrated the substrates in which good adhesion was expected. Though the surface modifications by CII and DLC hardened the surfaces, the surface with DLC was also roughened (R_a = 39 nm). In contrast, the surface modified by CII had a very smooth surface (R_a = 15 nm) and low friction coefficient (ranging from 0.15 to 0.20), resulting in a low rate of wear. Our findings suggest that CII on the Co? Cr? Mo alloy/UHMWPE pair offers potential benefits as a hard coating for artificial total‐joint arthroplasty. Copyright © 2008 John Wiley & Sons, Ltd.     

Photodegradation of poly(ether sulphone) Part 1. A time‐of‐flight secondary ion mass spectrometry study

An extensive study of the surface chemical changes to poly(ether sulphone) (PES) ultrafiltration membranes is made for the first time by the use of time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) after photoirradiation at 254 nm with irradiances varying from 10 to 300 mJ cm^?2 in a nitrogen atmosphere. Complementary information is provided by analysis with x‐ray photoelectron spectroscopy (XPS) and attenuated total reflectance Fourier transform infrared spectroscopy (ATR‐FTIR). The versatility, superior specificity and sensitivity of using ToF‐SIMS to investigate degradation phenomena are highlighted. The combined results demonstrate that photoirradiation causes a number of chemical changes to the surface: incorporation of oxygen; degradation of the benzene rings and formation of oxidized carbon species; depletion of carbon; reduction of ? SO₂? to some extent; formation of ? OH, C?O and ? SO₃H groups; and probable formation of ? C₆H₄? O? C₆H₅ end‐groups. In addition, no ? OSO₃H groups are formed and no formation of SO₂ is detected. Also, it is shown that chain scission dominates below an irradiation dose of ～200 mJ cm^?2 (at 254 nm in a nitrogen atmosphere). At higher doses, cross‐linking becomes dominant. Copyright © 2004 John Wiley & Sons, Ltd.     

New approaches to hyperbranched poly(4‐chloromethylstyrene) and introduction of various functional end groups by polymer‐analogous reactions

A facile way for the synthesis of hyperbranched poly(4‐chloromethylstyrene) [P(4‐CMS)] with adjustable molar mass by classic atom transfer radical polymerization (ATRP) and mechanistically similar procedures is presented. Subsequently, the chlorine functional groups have been modified to obtain polymers with different polarities. On the one hand, the polymer was end‐capped with unpolar groups (e.g., methyl, phenol ether) to obtain chemically inert substances. On the other hand, more complex functional groups have been introduced through azide groups by 1,3‐dipolar cycloaddition reaction (“click chemistry”). Furthermore, a method for the introduction of ester groups under mild conditions using cesium carboxylates is presented, which also allowed the preparation of so‐called hyperstars by attaching COOH functionalized polystyrene chains onto the P(4‐CMS) as core molecule. All these reactions were carried out in high or very high yields. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2224–2235, 2010     

Adsorption of polyfunctional 5‐fluorouracil and 2,4‐dithio‐5‐fluorouracil on Au(111) surface: Structure,energy, and electronic transmission

Adsorption of 5‐fluorouracil (5‐FU) and 2,4‐dithio‐5‐fluorouracil (2,4‐DT‐5‐FU) on Au(111) surface at low coverage is studied by using periodic‐slab‐density functional theory calculation. Isolated 5‐FU molecule adsorbs preferentially at bridge site in a vertical configuration via N? H group by forming the N? H···Au nonconventional H‐bond. The formation of the anchor Au? O bond is not observed. Substitution of oxygen atoms of 5‐FU with sulfur strongly influences the nature of adsorption and leads to the Au? S anchor bond and the N? H···Au nonconventional H‐bond of single 2,4‐DT‐5‐FU molecule on Au(111) surface. The adsorption site and orientation of 2,4‐DT‐5‐FU molecule on the surface are similar to those of 5‐FU. The metal–molecule coupling effects at asymmetric Au/S(N? H)S/mol/C? H/Au and Au/N? H/mol/O/Au transport junctions and symmetric Au/S(N? H)S/mol/mol/S(N? H)S/Au and Au/O/mol/mol/O/Au transport junctions are also investigated. The electronic structure is analyzed in detail, and the obtained results are used for illustrating the electron transmission in metal–molecule–metal systems. © 2011 Wiley Periodicals, Inc. Int J Quantum Chem, 2011     

pH‐ and Voltage‐Switchable Superhydrophobic Surfaces by Electro‐Copolymerization of EDOT Derivatives Containing Carboxylic Acids and Long Alkyl Chains

In order to produce pH‐ and voltage‐switchable superhydrophobic surfaces, PEDOT derivatives containing various proportions of a EDOT monomer containing carboxylic groups (EDOT? COOH) and EDOT monomer‐containing dodecyl chains (EDOT? O? H₁₂) are elaborated. The surface morphology and roughness depend highly on the proportion of the monomers. Superhydrophobic properties are reached for a mol % of EDOT? COOH between 0 and 25 %. It is possible to switch from superhydrophobic to hydrophilic (θ_water until about 45°) by electrochemical reduction at low voltage (?1 V vs SCE) to remove the doping anions, following by treatment with NaOH to change the carboxylic groups into carboxylate. By elaborating smooth surfaces of each polymer, the effect of each treatment is reported. The reversibility of the reactions is also reported.     

Impact of high N2 flow ratio on the chemical and morphological characteristics of sputtered N‐DLC films

Because of their outstanding characteristics, diamond‐like carbon (DLC) thin films have been recognized as interesting materials for a variety of applications. For this reason, the effects of the incorporation of different elements on their fundamental properties have been the focus of many studies. In this work, nitrogen‐incorporated DLC films were deposited on Si (100) substrates by DC magnetron sputtering of a graphite target under a variable N₂ gas flow rate in CH₄ + N₂ + Ar gas mixtures. The influence of high N₂ flow ratios (20, 40 and 60%) on the chemical, structural and morphological properties of N‐DLC films was investigated. Different techniques including field emission gun‐equipped scanning electron microscope (FEG‐SEM), energy‐dispersive X‐ray spectroscopy (EDS), atomic force microscopy (AFM), profilometry, Rutherford backscattering spectrometry (RBS) and Raman spectroscopy (325‐nm and 514‐nm excitation) were used to examine the properties of the N‐DLC films. Thus, the incorporation of nitrogen was correlated with the morphology, roughness, thickness, structure and chemical bonding of the films. Overall, the results obtained indicate that the fundamental properties of N‐DLC films are not only related to the nitrogen content in the film but also to the type of chemical bonds formed. Copyright © 2016 John Wiley & Sons, Ltd.     

Differentiation of α‐COOH from β‐COOH in aspartic acids by N‐phosphorylation

The biomimic reactions of N‐phosphoryl amino acids, which involved intramolecular penta‐coordinate phosphoric‐carboxylic mixed anhydrides, are very important in the study of many biochemical processes. The reactivity difference between the α‐COOH group and β‐COOH in phosphoryl amino acids was studied by experiments and theoretical calculations. It was found that the α‐COOH group, and not β‐COOH, was involved in the ester exchange on phosphorus in experiment. From MNDO calculations, the energy of the penta‐coordinate phosphoric intermediate containing five‐member ring from α‐COOH was 35 kJ/mol lower than that of the six‐member one from β‐COOH. This result was in agreement with that predicted by HF/6‐31G** and B3LYP/6‐31G** calculations. Theoretical three‐dimensional potential energy surface for the intermediates predicted that the transition states 4 and 5 involving α‐COOH or β‐COOH group had energy barriers of ΔE=175.8 kJ?mol^?1 and 210.4 kJ?mol^?1, respectively. So the α‐COOH could be differentiated from β‐COOH intramolecularly in aspartic acids by N‐phosphorylation. © 2001 John Wiley & Sons, Inc. Int J Quant Chem 83: 41–51, 2001     

2,2‐Bis(ethoxycarbonyl)vinyl (BECV) as a Versatile Amine Protecting Group for Selective Functional‐Group Transformations

A 2,2‐Bis(ethoxycarbonyl) vinyl‐ (BECV) group was used for the selective protection of amines at room temperature in the presence of potentially interfering functional groups such as OH, SH, COOH as well as other NH₂ groups. Several functional group transformations such as esterification, O‐alkylation, O‐acylation, N‐alkylation, N‐acylation, S‐alkylation can selectively be carried out in the presence of the BECV group. The selective deprotection of the BECV group was achieved in a short time using ethylenediamine at room temperature while several other functional groups such as benzoate, aliphatic esters, amides and ethers remain intact. The BECV group shows orthogonal stability against the common protecting groups such as Fmoc, Cbz and Boc.     

Adsorption and Decomposition Mechanism of 1,1‐Diamino‐2,2‐dinitroethylene on Al(111) Surface by Periodic DFT Calculations

The adsorption of 1,1‐diamino‐2,2‐dinitroethylene (FOX‐7) molecule on the Al(111) surface was investigated by the generalized gradient approximation (GGA) of density functional theory (DFT). The calculations employ a supercell (4×4×2) slab model and three‐dimensional periodic boundary conditions. The strong attractive forces between oxygen and aluminum atoms induce the N? O bond breaking of the FOX‐7. Subsequently, the dissociated oxygen atoms and radical fragment of FOX‐7 oxidize the Al surface. The largest adsorption energy is ?940.5 kJ/mol. Most of charge transfer is 3.31e from the Al surface to the fragment of FOX‐7 molecule. We also investigated the adsorption and decomposition mechanism of FOX‐7 molecule on the Al(111) surface. The activation energy for the dissociation steps of P2 con?guration is as large as 428.8 kJ/mol, while activation energies of other con?gurations are much smaller, in range of 2.4 to 147.7 kJ/mol.     

Photocurrent Enhancement of Dye‐Sensitized Solar Cells owing to Increased Dye‐Adsorption onto Silicon‐Nanoparticle‐Coated Titanium‐Dioxide Films

The inverse‐micellar preparation of Si nanoparticles (Nps) was improved by utilizing sodium naphthalide. The Si Nps were subsequently functionalized with 4‐vinylbenzoic acid for their attachment onto TiO₂ films of dye‐sensitized solar cells (DSSCs). The average diameter of the COOH‐functionalized Si (Si? COOH) Nps was 4.6(±1.7) nm. Depth profiling by secondary‐ion mass spectrometry revealed that the Si Nps were uniformly attached onto the TiO₂ films. The number of Ru^II dye molecules adsorbed onto a TiO₂ film that was treated with the Si? COOH Nps was 42 % higher than that on the untreated TiO₂ film. As a result, DSSCs that incorporated the Si? COOH Nps exhibited higher short‐circuit photocurrent density and an overall energy‐conversion efficiency than the untreated DSSCs by 22 % and 27 %, respectively. This enhanced performance, mostly owing to the intramolecular charge‐transfer to TiO₂ from the dye molecules that were anchored to the Si? COOH Nps, was confirmed by comparing the performance with two different Ru^II–bipyridine dyes (N719 and N749).     

Size effect in the titanium/diamond‐like carbon bilayer films: effect of relative thickness on their structure and mechanical properties

Titanium/diamond‐like carbon (Ti/DLC) bilayer films with different relative thickness were fabricated by direct‐current and pulsed cathode arc plasma method. Microstructure, morphological characteristics, and mechanical properties of the films were investigated in dependence of the thickness of Ti and DLC layers by Raman spectroscopy, atomic force microscopy, Knoop sclerometer, and surface profilometer. Raman spectra of Ti/DLC bilayers show the microstructure evolution (the size and ordering degree of sp²‐hybridized carbon clusters) with varying the thicknesses of Ti interlayer and DLC layer. Nano‐scaled Ti interlayer of 12–20 nm thickness presents the largest size effect. The catalytic effect of the sublayer is most pronounced in the carbon layer of less than 106 nm. In these thickness ranges, the bilayer films possessed the highest micro‐hardness and reactivity between atoms at interface. Internal stress in the bilayer monotonically decreases, with the thickness of Ti interlayer increasing to 30 nm and then becomes stable with the thickness. These results are associated with the occurrence of atomic diffusion process at Ti/C interface, and they are of cardinal significance to optimize the structure and mechanical properties of carbon‐based multilayer films. Copyright © 2016 John Wiley & Sons, Ltd.     

Corrosion and tribocorrosion behaviour of super‐thick diamond‐like carbon films deposited on stainless steel in NaCl solution

Super‐thick diamond‐like carbon (DLC) film is a potential protective coating in corrosive environments. In the present work, three kinds of DLC films whose thickness and modulation periods are 4 µm and 3, 21 µm and 17 and 21 µm and 7, respectively, were fabricated on stainless steel. The effect of different thickness and modulation periods on corrosion and tribocorrosion behaviour of the DLC‐coating stainless steel was investigated in 3.5 wt% NaCl aqueous solution by a ball‐on‐flat tribometer equipped with a three‐electrode electrochemical cell. The DLC‐coating stainless steel served as a working electrode, and its OCP and potentiodynamic polarization were monitored before and during rubbing. The wear–corrosion mechanism of the DLC films was investigated by SEM. The results showed that the increasing thickness can prolong significantly lifetime of DLC films in NaCl aqueous solution. In particular, the modulation period has a significant impact on the tribocorrosion resistance of the DLC super‐thick films. The study suggested that the increasing thickness of compressive stress layer could suppress film damage by reducing crack propagation rate. Thus, the super‐thick DLC film with thickness of 21 µm and 7 periods presented the best tribocorrosion resistance among all studied films. Copyright © 2016 John Wiley & Sons, Ltd.     

Carbonyl group‐containing organometallic intramolecular‐coordination five‐membered ring compounds

Carbonyl group‐containing organometallic intramolecular‐coordination five‐membered ring compounds are easily synthesized by the following five reaction methods: (1) cyclometalation, especially, orthometalation reactions; (2) the reactions of the moieties of an unsaturated carbon? carbon bond attached to a carbonyl group (C?C? CO, C?C? CO); (3) the reactions of an unsaturated carbon? carbon bond with carbon monoxide (C?C and CO, C?C and CO); (4) carbonylative ring expansion reactions; and (5) others. These compounds are very easily and regio‐specifically synthesized with many kinds of metal compounds, including both transition metals and main group metals. Many of such the reactions are easily applied to organic syntheses. Copyright © 2010 John Wiley & Sons, Ltd.     

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions as a route to well‐defined mono and bis end‐functionalized poly(N‐isopropylacrylamide)

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used as a facile and quantitative method for modifying end‐groups on an N‐isopropylacrylamide (NIPAm) homopolymer. A well‐defined precursor of polyNIPAm (PNIPAm) was prepared via reversible addition‐fragmentation chain transfer (RAFT) polymerization in DMF at 70 °C using the 1‐cyano‐1‐methylethyl dithiobenzoate/2,2′‐azobis(2‐methylpropionitrile) chain transfer agent/initiator combination yielding a homopolymer with an absolute molecular weight of 5880 and polydispersity index of 1.18. The dithiobenzoate end‐groups were modified in a one‐pot process via primary amine cleavage followed by phosphine‐mediated nucleophilic thiol‐ene click reactions with either allyl methacrylate or propargyl acrylate yielding ene and yne terminal PNIPAm homopolymers quantitatively. The ene and yne groups were then modified, quantitatively as determined by ¹H NMR spectroscopy, via radical thiol‐ene and radical thiol‐yne reactions with three representative commercially available thiols yielding the mono and bis end functional NIPAm homopolymers. This is the first time such sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used in polymer synthesis/end‐group modification. The lower critical solution temperatures (LCST) were then determined for all PNIPAm homopolymers using a combination of optical measurements and dynamic light scattering. It is shown that the LCST varies depending on the chemical nature of the end‐groups with measured values lying in the range 26–35 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3544–3557, 2009     

The influence of anti‐wear additive ZDDP on doped and undoped diamond‐like carbon coatings

Diamond‐like carbon (DLC) coatings are recognised as a promising way to reduce friction and improve wear performance of automotive engine components. DLC coatings provide new possibilities in the improvement of the tribological performance of automotive components beyond what can be achieved with lubricant design alone. Lubricants are currently designed for metallic surfaces, the tribology of which is well defined and documented. DLC does not share this depth of tribological knowledge; thus, its practical implementation is stymied. In this work, three DLC coatings are tested: an amorphous hydrogenated DLC, a silicone‐doped amorphous hydrogenated DLC and a tungsten‐doped amorphous hydrogenated DLC. The three coatings are tested tribologically on a pin‐on‐reciprocating plate tribometer against a cast iron pin in a group III base oil, and a fully formulated oil that consists of a group III base oil and contains ZDDP, at 100 °C for 6 h and for 20 h in order to determine whether a phosphor‐based tribofilm is formed at the contact. The formation of a tribofilm is characterised using atomic force microscopy and X‐ray photoelectron spectroscopy techniques. The main findings of this study are the formation of a transfer film at the undoped, amorphous hydrogenated DLC surface, and also the tungsten amorphous hydrogenated DLC having a significant wear removal during the testing. The three coatings were found to have differing levels of wear, with the tungsten‐doped DLC showing the highest, the silicon‐doped DLC showing some coating removal and the amorphous hydrogenated DLC showing only minimal signs of wear. Copyright © 2015 John Wiley & Sons, Ltd.