Photoactivated Preparation and Patterning of Self-Assembled Monolayers with 1-Alkenes and Aldehydes on Silicon Hydride Surfaces

Direct lateral patterning in the formation of self-assembled monolayers (SAMs) on silicon was achieved by the photoinduced reaction of aldehydes with Si(111)-H surfaces by using the usual masking techniques (see the schematic illustration; on the right-hand side is a microscopy image of a patterned SAM formed from octadecanal).     

In situ growth of CuS thin films on functionalized self-assembled monolayers using chemical bath deposition

Nano-structured CuS thin films were deposited on the functionalized -NH(2)-terminated self-assembled monolayers (SAMs) surface by chemical bath deposition (CBD). The deposition mechanism of CuS on the -NH(2)-terminated group was systematically investigated using field emission scanning electron microscope (FESEM), X-ray photoelectron spectroscope (XPS), UV-vis absorption. The optical, electrical and photoelectrochemical performance of CuS thin films incorporating with the X-ray diffraction (XRD) analysis confirmed the nanocrystalline nature of CuS with hexagonal crystal structure and also revealed that CuS thin film is a p-type semiconductor with high electrical conductivity (12.3Ω/□). The functionalized SAMs terminal group plays a key role in the deposition of CuS thin films. The growth of CuS on the varying SAMs surface shows different deposition mechanisms. On -NH(2)-terminated surfaces, a combination of ion-by-ion growth and cluster-by-cluster deposition can interpret the observed behavior. On -OH- and -CH(3)-terminated surfaces, the dominant growth mechanism on the surface is cluster-by-cluster deposition in the solution. According to this principle, the patterned CuS microarrays with different feature sizes were successfully deposited on -NH(2)-terminated SAMs regions of -NH(2)/-CH(3) patterned SAMs surface.     

Self-assembled monolayers of alkanethiolates on palladium are good etch resists

This paper describes microcontact printing (muCP) of long-chain alkanethiolates on palladium, followed by solution-phase etching with an iron(III)-based etchant, to make patterned structures. The commonly used soft-lithographic procedure for fabricating microstructures-muCP of SAMs on gold-has three shortcomings: a significant surface density of pinhole defects, substantial edge roughness, and incompatibility with processes used in CMOS fabrication. Microcontact printing on palladium gives fewer defects and smaller edge roughness than on gold, and is compatible with CMOS. The mechanism by which etch-resistant patterns are formed is different for palladium and gold. The Pd/S interfacial layer formed by the reaction of palladium films with sulfur-containing compounds provides good resistance to etches independently of the barrier to access the surface provided by the film of (CH2)n groups in the long-chain SAMs. This barrier is the basis of the etch resistance of SAMs on gold, but only supplements the etch resistance of the sulfur-containing interfacial layer on palladium. Characterization of the SAM formed from hexadecanethiol on palladium is described.     

A case study on biological activity in a surface-bound multicomponent system: the biotin-streptavidin-peroxidase system

The adsorption of multiple protein layers on biotinylated organic surfaces has been characterized using surface plasmon resonance (SPR) and atomic force microscopy (AFM). Diffusion-limited loading of the biotinylated self-assembled monolayers (SAMs) ensures a precise control of the streptavidin surface density. For the subsequent interaction with biotinylated peroxidase, SPR data hint at a streptavidin density dependent orientation during peroxidase adsorption. Microcontact printed well-defined two-dimensional patterned surfaces of biotinylated organothiols and protein-resistant OEG-thiols allow an in-situ differentiation of specific and nonspecific adsorption (e.g., mono- vs multilayer adsorption). Additionally, the very important issue of biological activity of surface-bound enzymes is addressed by comparing the enzyme activities in solution with that for surface-bound species.     

Microcontact printing for creation of patterned lipid bilayers on tetraethylene glycol self-assembled monolayers

Supported lipid bilayers (SLBs) formed on many different substrates have been widely used in the study of lipid bilayers. However, most SLBs suffer from inhomogeneities due to interactions between the lipid bilayer and the substrate. In order to avoid this problem, we have used microcontact printing to create patterned SLBs on top of ethylene-glycol-terminated self-assembled monolayers (SAMs). Glycol-terminated SAMs have previously been shown to resist absorbance of biomolecules including lipid vesicles. In our system, patterned lipid bilayer regions are separated by lipid monolayers, which form over the patterned hexadecanethiol portions of the surface. Furthermore, we demonstrate that α-hemolysin, a large transmembrane protein, inserts preferentially into the lipid bilayer regions of the substrate.     

单壁碳纳米管在金表面的图形化组装

利用湿法化学组装技术在金表面得到了图形化的单壁碳纳米管阵列.在混酸氧化条件下,初合成的交缠状态的单壁纳米管被截短成带有羧基等功能化末端的短管.这些功能化的短管在缩合剂DCC的作用下与氨基/甲基图形化表面进行缩合反应时,纳米管将选择性地结合到氨基区域从而形成规则的纳米管阵列.     

Selected-area sol-gel deposition of barium strontium titanate thin films on thermally oxidized silicon through mediation of self-assembled monolayers

Self-assembled monolayers (SAMs) of octadecyltrichlorosilane (OTS) and mercapto ethanol were used to modify the surface functionality of platinum/titanium or platinum/tantalum bilayer patterns on thermally oxidized silicon wafers. The attachment of OTS to the exposed oxide region made it hydrophobic, while the anchoring of mercapto ethanol to the bilayer pattern turned it hydrophilic. This patterned hydrophobicity and hydrophilicity was exploited to preferentially deposit barium strontium titanate (BST) thin films on the patterned bilayers from an aqueous sol-gel solution. The combination of the SAMs and the sol-gel film formation method allowed direct patterned deposition of BST thin films, which could be useful for on-chip electronic applications. Wet oxygen annealing at 50 °C was sufficient to stabilize the deposited sol-gel coating without adversely affecting the functionality of the OTS, thus permitting multiple dip-coatings to obtain patterned films of a desired thickness. Heat treatment at 750 °C allowed densification and conversion of the sol-gel coatings to perovskite BST films.     

Directed growth of poly(isobenzofuran) films by chemical vapor deposition on patterned self-assembled monolayers as templates

This paper describes a method to direct the formation of microstructures of poly(isobenzofuran) (PIBF) by chemical vapor deposition (CVD) on chemically patterned, reactive, self-assembled monolayers (SAMs) prepared on gold substrates. We examined the growth dependence of PIBF by deposition onto several different SAMs each presenting different surface functional groups, including a carboxylic acid, a phenol, an alcohol, an amine, and a methyl group. Interferometry, Fourier transform infrared (FT-IR) spectroscopy, X-ray photoelectron spectroscopy (XPS), gel permeation chromatography (GPC), and optical microscopy were used to characterize the PIBF films grown on the various SAMs. Based on the kinetic and the spectroscopic analyses, we suggest that the growth of PIBF is surface-dependent and may follow a cationic polymerization mechanism. Using the cationic polymerization mechanism of PIBF growth, we also prepared patterned SAMs of 11-mercapto-1-undecanol (MUO) or 11-mercaptoundecanoic acid (MUA) by microcontact printing (microCP) on gold substrates as templates, to direct the growth of the PIBF. The directed growth and the formation of microstructures of PIBF with lateral dimensions of 6 microm were investigated using atomic force microscopy (AFM). The average thickness of the microstructures of PIBF films grown on the MUO and the MUA patterns were 400 +/- 40 nm and 490 +/- 40 nm, respectively. SAMs patterned with carboxylic acid salts (Cu2+, Fe2+, or Ag+) derived from MUA led to increases in the average thickness of the microstructures of PIBF by 10%, 12%, or 27%, respectively, relative to that of control templates. The growth dependence of PIBF on the various carboxylic acid salts was also investigated using experimental observations of the growth kinetics and XPS analyses of the relative amount of metal ions present on the template surfaces.     

Zinc oxide growth morphology on self-assembled monolayer modified silver surfaces

Using organic molecules to direct inorganic crystal growth has opened up new avenues for controlled synthesis on surfaces. Combined with soft lithography to form patterned templates, self-assembled monolayers (SAMs) have been shown to be a powerful approach for the assembly of inorganic nanostructures. In this work, we show that the surface free energy of SAM-modified silver, which depends on end groups and deposition method of SAMs, has a dramatic effect on the nucleation and growth of crystalline ZnO, a technologically important material, from supersaturated solutions. For SAMs with inert methyl end groups, ZnO nucleation is inhibited. For SAMs with chemically active (carboxylic or thiol) end groups, the ZnO morphology is found to be three-dimensional nanorods on low-surface-energy surfaces and two-dimensional thin films on high-energy surfaces.     

Dependence of patterned binary alkanethiolate self-assembled monolayers on "UV-photopatterning" conditions and evolution with time, terminal group, and methylene chain length

We have investigated the mechanism of UV photopatterning of binary alkanethiolate self-assembled monolayers (SAMs) adsorbed on Au(111) using time-of-flight secondary ion mass spectrometry. The SAMs were photopatterned using a 500 W Hg arc lamp. The patterning process is strongly dependent on the wavelength of light used. When an unfiltered arc lamp is employed, IR light impinges on the sample and causes considerable sample heating. Methyl-terminated SAMs with less than 14 carbons in the chain melt at the temperatures reached and become very disordered and so can be easily displaced by a second SAM. This leads to significant pattern degradation ("erosion"). SAMs with greater than 14 carbons undergo a transition to an incommensurate phase but remain stable on the surface, and the pattern is retained. When the IR light is filtered out, a different behavior is observed. UV-photopatterned methyl-terminated SAMs with 10 carbons in the chain are stable. Terminal group interactions, such as H-bonding, provide extra stabilization energy during photopatterning, so some patterns with shorter carbon chains may also be stable. The displacement of the photooxidized SAMs on the patterned surface follows kinetics similar to that of large-area SAM formation.     

Reversible covalent patterning of self-assembled monolayers on gold and silicon oxide surfaces

This paper describes the generation of reversible patterns of self-assembled monolayers (SAMs) on gold and silicon oxide surfaces via the formation of reversible covalent bonds. The reactions of (patterned) SAMs of 11-amino-1-undecanethiol (11-AUT) with propanal, pentanal, decanal, or terephthaldialdehyde result in dense imine monolayers. The regeneration of these imine monolayers to the 11-AUT monolayer is obtained by hydrolysis at pH 3. The (patterned) monolayers were characterized by Fourier transform infrared reflection absorption spectroscopy, X-ray photoelectron spectroscopy, contact angle and electrochemical measurements, and atomic force microscopy. Imines can also be formed by microcontact printing of amines on terephthaldialdehyde-terminated substrates. Lucifer Yellow ethylenediamine was employed as a fluorescent amine-containing marker to visualize the reversible covalent patterning on a terephthaldialdehyde-terminated glass surface by confocal microscopy. These experiments demonstrate that with reversible covalent chemistry it is possible to print and erase chemical patterns on surfaces repeatedly.     

Sulfonic Acid-functionalized gold nanoparticles: a colloid-bound catalyst for soft lithographic application on self-assembled monolayers

In this report, we present a new lithographic approach to prepare patterned surfaces. Self-assembled monolayers (SAMs) of the acid-labile trimethylsilyl ether (TMS-OC(11)H(22)S)(2) (TMS adsorbate) was formed on gold. 5-Mercapto-2-benzimidazole sulfonic acid sodium salt (MBS-Na(+)) was used as a ligand for gold nanoparticles. These monolayer-protected gold colloids (MPCs) were transformed into the catalytically active H(+)-form by ion exchange. This colloid-bound catalyst hydrolyzed the TMS adsorbate (TMS-OC(11)H(22)S)(2) both in solution and when self-assembled on gold surfaces. Microcontact printing of the active colloid-bound catalyst on the preformed TMS SAM led to the deposition of the colloid onto the SAMs. After the catalyst nanoparticles were rinsed off, a patterned surface was created as shown by AFM.     

Tunable magnetic properties of nanoparticle two-dimensional assemblies addressed by mixed self-assembled monolayers

Assemblies of magnetic nanoparticles (NPs) are intensively studied due to their high potential applications in spintronic, magnetic and magneto-electronic. The fine control over NP density, interdistance, and spatial arrangement onto substrates is of key importance to govern the magnetic properties through dipolar interactions. In this study, magnetic iron oxide NPs have been assembled on surfaces patterned with self-assembled monolayers (SAMs) of mixed organic molecules. The modification of the molar ratio between coadsorbed 11-mercaptoundecanoic acid (MUA) and mercaptododecane (MDD) on gold substrates is shown to control the size of NPs domains and thus to modulate the characteristic magnetic properties of the assemblies. Moreover, NPs can be used to indirectly probe the structure of SAMs in domains at the nanometer scale.     

Synthesis of patterned polymer brushes from flexible polymeric films

Surface-initiated polymerizations were carried out from polymeric surfaces of commercially important polyester films, poly(ethylene terephthalate) (PET) and poly(ethylene naphthalate) (PEN). These plastic films were modified prior to polymerization by plasma oxidation, exposing surface hydroxyl groups, in order to immobilise patterned self assembled monolayers (SAMs) of trichlorosilane initiator, through the soft lithographic method of microcontact printing (μCP). Subsequently, polymerizations were initiated from the surface via controlled atom transfer radical polymerization (ATRP), under aqueous conditions, to create patterned brushes of the thermo-responsive polymer poly(N-isopropyl acrylamide) (PNIPAM). By creating patterned, rather than homogeneous brushes characterization was made possible by atomic force microscopy (AFM).     

Microfluidic lithography of SAMs on gold to create dynamic surfaces for directed cell migration and contiguous cell cocultures

A straightforward, flexible, and inexpensive method to create patterned self-assembled monolayers (SAMs) on gold using microfluidics-microfluidic lithography-has been developed. Using a microfluidic cassette, alkanethiols were rapidly patterned on gold surfaces to generate monolayers and mixed monolayers. The patterning methodology is flexible and, by controlling the solvent conditions and thiol concentration, permeation of alkanethiols into the surrounding PDMS microfluidic cassette can be advantageously used to create different patterned feature sizes and to generate well-defined SAM surface gradients with a single microfluidic chip. To demonstrate the utility of microfluidic lithography, multiple cell experiments were conducted. By patterning cell adhesive regions in an inert background, a combination of selective masking of the surface and centrifugation achieved spatial and temporal control of patterned cells, enabling the design of both dynamic surfaces for directed cell migration and contiguous cocultures. Cellular division and motility resulted in directed, dynamic migration, while the centrifugation-aided seeding of a second cell line produced contiguous cocultures with multiple sites for heterogeneous cell-cell interactions.     

Preparation and photoinduced patterning of azidoformate-terminated self-assembled monolayers

This paper presents a new method for the patterning of self-assembled monolayers (SAMs) using UV light. Azidoformate-terminated SAMs starting from 18-acetoxy-octadecyltrichlorosilane SAMs on silicon, prepared for the first time, are electrophilic and photosensitive, and can be patterned by UV irradiation through a mask. The resulting structured surfaces are still electrophilic and can be reacted with nucleophilic functions, for example, primary amines.     

Tunable resistive m-dPEG acid patterns on polyelectrolyte multilayers at physiological conditions: template for directed deposition of biomacromolecules

This paper describes a new class of salt-responsive poly(ethylene glycol) (PEG) self-assembled monolayers (SAMs) on top of polyelectrolyte multilayer (PEMs) films. PEM surfaces with poly(diallyldimethylammonium chloride) as the topmost layer are chemically patterned by microcontact printing (muCP) oligomeric PEG molecules with an activated carboxylic acid terminal group (m-dPEG acid). The resistive m-d-poly(ethylene glycol) (m-dPEG) acid molecules on the PEMs films were subsequently removed from the PEM surface with salt treatment, thus converting the nonadhesive surfaces into adhesive surfaces. The resistive PEG patterns facilitate the directed deposition of various macromolecules such as polymers, dyes, colloidal particles, proteins, liposomes, and nucleic acids. Further, these PEG patterns act as a universal resist for different types of cells (e.g., primary cells, cell lines), thus permitting more flexibility in attaching a wide variety of cells to material surfaces. The patterned films were characterized by optical microscopy and atomic force microscopy (AFM). The PEG patterns were removed from the PEM surface at certain salt conditions without affecting the PEM films underneath the SAMs. Removal of the PEG SAMs and the stability of the PEM films underneath it were characterized with ellipsometry and optical microscopy. Such salt- and pH-responsive surfaces could lead to significant advances in the fields of tissue engineering, targeted drug delivery, materials science, and biology.     

Surface plasmon microscopy of biotin-streptavidin binding reactions on UV-photopatterned alkanethiol self-assembled monolayers

We report surface plasmon imaging of streptavidin binding to photopatterned biotinylated alkanethiol self-assembled monolayers (SAMs) on gold. Micrometer-scale patterns of a mixed biotin- and hydroxyl-terminated monolayer were formed in an inert, hydroxy-terminated alkanethiol monolayer using a UV-photopatterning procedure. Using surface plasmon microscopy, contrast is readily observed between the mixed biotin- and hydroxy-terminated SAM region after specific binding of streptavidin has occurred and the pure hydroxy-terminated region where nonspecific binding of streptavidin is negligible. Surface plasmon microscopy was also able to monitor in situ and in real time the binding of streptavidin to the patterned SAMs. The ability of surface plasmon microscopy to detect and spatially resolve 2-dimensional monolayer binding events may prove useful in diagnostic applications involving the parallel interrogation at surface biomolecular arrays.     

Effect of the chemical composition on the work function of gold substrates modified by binary self-assembled monolayers

This study demonstrated that the work function (Φ) of Au substrates can be fine-tuned by using series ratios of binary self-assembled monolayers (SAMs). By using pure amine- and carboxylic acid-bearing alkanethiol SAM on gold substrates, Φ of Au changed from 5.10 to 5.16 and 5.83, respectively, as determined by ultra-violet photoelectron spectrometry (UPS). The shift in Φ due to the use of different functional groups was rationalized by considering the dipole moments of the molecules anchored on the Au surface. A series of binary SAMs were fabricated by mixing carboxylic acid- and amine-terminated alkanethiols in the deposition solution. By mixing these functional groups in SAMs, a linear correlation between Φ with respect to chemical composition (hence the effective dipole moment on the Au surface) was observed. It was found that arbitrary Φ between extremes (5.16 and 5.83) controlled by respective functional groups can be obtained by changing the chemical composition of SAMs. The Scanning Kelvin Probe (SKP) was also used to measure the contact potential difference (CPD) between SAMs and referencing Au on a patterned substrate prepared by photo-lithography. It was found that the CPD of SAMs with different chemical compositions correlates to their Φ. However, the magnitude of the CPD was smaller than the difference in Φ measured by UPS that was possibly due to the adsorption of contaminants in air.     

Multicolor, large-area fluorescence sensing through oligothiophene-self-assembled monolayers

We present a new strategy to realize self-assembled monolayers (SAMs) on quartz and silicon with a multicolour fluorescence pattern starting from a single, proton sensitive oligothiophene dye exposed at a defined pH. Fine tuning of the SAMs emission color over the entire visible range, including white, is demonstrated. Finally, integration of SAMs in patterned thin layer cells (TLCs) is exploited to demonstrate cation sensing potential in real devices.