Photoreactive Polynorbornene Bearing 4-(Diphenylamino)benzoate Groups: Synthesis and Application in Electroluminescent Devices

A new fluorescent and photoreactive polymer, poly-(endo,exo-bis(4-(4-(diphenylamino)benzoyloxy)benzyl)bicyclo[2.2.1]hept-5-ene-2,3-dicarboxylate), was prepared by ring opening metathesis polymerization. This polymer combines the photoreactivity of aryl esters with the fluorescence properties of derivatives of 4-(diphenylamino)benzoic acid. The polymer exhibits blue photo- and electroluminescence and can be used as active layer in organic light emitting devices (OLED). Upon irradiation with UV light (254 nm) the aromatic ester groups undergo decarboxylation, which is accompanied by the loss of photoluminescence. Photolithographic patterning of the polymer surface was used to obtain structured fluorescent surfaces and patterned OLEDs.     

Synthesis and characterization of diphenylaminodiphenyl stryl based alternating copolymers

Diphenylaminobiphenylated stryl based alternating copolymers with phenyl or fluorene, which were expected to have a terphenylene vinylene backbone containing an (N,N‐diphenylamino)biphenyl pendant and a phenyl/fluorene/phenylene vinylene backbone containing an (N,N‐diphenylamino)biphenyl pendant, were synthesized by a Suzuki coupling reaction. The obtained copolymers were confirmed with various types of spectroscopy. The alternating copolymers showed good hole‐injection properties because of their low oxidation potential and good solubility and high thermal stability with a high glass‐transition temperature. The alternating copolymers showed blue emissions because of the adjusted conjugation lengths; the maximum wavelength was 460 nm for poly{4,4′‐biphenylene‐α‐[4″‐(N,N′‐diphenylamino)diphenyl]vinylene‐alt‐5‐(2′‐ethylhexyloxy)‐2‐methoxybenzene} and 487 nm for poly{4,4′‐biphenylene‐α‐[4″‐(N,N′‐diphenylamino)diphenyl] vinylene‐alt‐9,9‐dihexylfluorene}. The maximum brightness of indium tin oxide/poly(3,4‐ethylene dioxythiophene)/polymer/LiF/Al devices with poly{4,4′‐biphenylene‐α‐[4″‐(N,N′‐diphenylamino)diphenyl]vinylene‐alt‐5‐(2′‐ethylhexyloxy)‐2‐methoxybenzene} or poly{4,4′‐biphenylene‐α‐[4″‐(N,N′‐diphenylamino)diphenyl]vinylene‐alt‐9,9‐dihexylfluorene} as the emitting layer was 250 or 1000 cd/m², respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 341–347, 2007     

Synthesis,characterization, and electroluminescence of new conjugated PPV derivatives bearing triphenylamine side‐chain through a vinylene bridge

Three new conjugated poly(p‐phenylene vinylene) (PPV) derivatives bearing triphenylamine side‐chain through a vinylene bridge, poly(2‐(4′‐(diphenylamino)phenylenevinyl)‐1,4‐phenylene‐vinylene) (DP‐PPV), poly(2‐(3′‐(3″,7″‐dimethyloctyloxy)phenyl)‐1,4‐phenylenevinylene‐alt‐2‐(4′‐ (diphenylamino)phenylenevinyl)‐1,4‐phenylenevinylene) (DODP‐PPV), and poly(2‐(4′‐(diphenylamino)phenylenevinyl)‐1,4‐phenylenevinylene‐co‐2‐(3′,5′‐bis(3″,7″‐dimethyloctyloxy)‐1,4‐phenylenevinylene) (DP‐co‐BD‐PPV), were synthesized according to the Gilch or Wittig method. Among the three polymers, the copolymer DP‐co‐BD‐PPV is soluble in common solvents with good thermal stability with 5% weight loss at temperatures higher than 386°C. The weight‐average molecular weight (M_w) and polydispersity index (PDI) of DP‐co‐BD‐PPV were 1.83 × 10⁵ and 2.33, respectively. The single‐layer polymer light‐emitting diodes (PLEDs) with the configuration of Indium tin oxide (ITO)/poly (3,4‐ethylenedioxythiophene): poly(4‐styrene sulfonate)(PEDOT:PSS)/DP‐co‐BD‐PPV/Ca/Al were fabricated. The PLED emitted yellow‐green light with the turn‐on voltage of ca. 4.9 V, the maximum luminance of ca. 990 cd/m² at 15.8 V, and the maximum electroluminescence (EL) efficiency of 0.22 cd/A. Copyright © 2007 John Wiley & Sons, Ltd.     

Efficient blue‐green‐emitting poly[(5‐diphenylamino‐1,3‐phenylenevinylene)‐alt‐(2,5‐dihexyloxy‐1,4‐phenylenevinylene)] derivatives: Synthesis and optical properties

New poly(phenylene vinylene) derivatives with a 5‐diphenylamino‐1,3‐phenylene linkage (including polymers 2 , 3 , and 5 ) have been synthesized to improve the charge‐injection properties. These polymers are highly photoluminescent with fluorescent quantum yields as high as 76% in tetrahydrofuran solutions. With effective π‐conjugation interruption at adjacent m‐phenylene units, chromophores of different conjugation lengths can be incorporated into the polymer chain in a controllable manner. In polymer 2 , the structural regularity leads to an isolated, well‐defined emitting chromophore. Isomeric polymer 3 of a random chain sequence, however, allows the effective emitting chromophores to be joined in sequence by sharing a common m‐phenylene linkage (as shown in a molecular fragment). Double‐layer light‐emitting‐diode devices using 2 , 3 , and 5 as emitting layers have turn‐on voltages of about 3.5 V and produce blue‐green emissions with peaks at 493, 492, and 482 nm and external quantum efficiencies up to 1.42, 0.98, and 1.53%, respectively. In comparison with a light‐emitting diode using 2 , a device using 3 shows improved charge injection and displays increased brightness by a factor of ～3 to 1400 cd/m² at an 8‐V bias. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2307–2315, 2006     

Dual roles for promoting monomers to polymers: A conjugated sulfonium salt photoacid generator as photoinitiator and photosensitizer in cationic photopolymerization

An efficient strategy for comprehensive utilization of the conjugated sulfonium salt photoacid generator (PAG), namely, 3‐{4‐[4‐(4‐N,N′‐diphenylamino)‐styryl]phenyl}phenyl dimethyl sulfonium hexafluoroantimonate, was developed through photoinitiated cationic photopolymerization (CP) of epoxides and vinyl ether upon exposure to near‐UV and visible light‐emitting diodes (LEDs; e.g., 365, 385, 405, and 425 nm). Photochemical mechanisms were investigated by UV–vis spectra, molecular orbital calculations, fluorescence, cyclic voltammetry, and electron spin resonance spin‐trapping analyses. Compared with commercial PAGs, the prepared conjugated sulfonium salt generated H⁺, which can be used as photoinitiator. Moreover, the fluorescent byproducts from photodecomposition can be used as photosensitizer of commercial iodonium salt in the photoinitiating systems of CP. These novel D‐π‐A type sulfonium‐based photoinitiating systems are efficient (epoxide conversion = 85–90% and vinyl conversion >90%; LEDs upon exposure to 365–425 nm) even in low‐concentration initiators (1%, w/w) and low curing light intensities (10–40 mW cm^?2). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2722–2730     

两种固体荧光有机-无机杂化物的合成、结构及强红光发射

采用（E）-4-（4-（diphenylamino）styryl）-1-methylpyridinium iodide（DPASPI,DPASP=（E）-4-（4-（diphenylamino）styryl）-1-methylpyridi-nium）,设计合成2种新型有机-无机杂化物（DPASP）₂[Zn（NCS）₄]·2CH₃OH（1）和{（DPASP）₂[Cd（SCN）（NCS）₃]·2CH₃OH}_n（2）。通过单晶X射线衍射进行了表征,结果表明杂化物1和2是由有机吡啶阳离子和异硫氰酸金属配阴离子组成的,具有不同空间结构。通过¹H NMR谱图解释了离子间相互作用。对具有高量子产率的杂化物1和2的红光发光性质进行了研究。     

Polytriphenylamines synthesized by interfacial and microemulsion oxidative polymerization

Two triphenylamine-based polymers were successfully prepared by the interfacial and microemulsion oxidative polymerization of triphenylamine and 4-(diphenylamino)benzyl 2-bromo-2-methylpropanoate. Ammonium peroxodisulfate ((NH₄)₂S₂O₈) was used as a chemical oxidant and dichloromethane/water was used as a solvent. Sodium dodecyl benzene sulfonate was employed as a surfactant in the microemulsion system. Polytriphenylamines were characterized via Fourier transform infrared (FTIR) spectra and ¹H-NMR and UV–vis absorption spectroscopy. Molecular weights were determined by gel permeation chromatography and redox properties were studied by cyclic voltammetry. The surface morphology of thin polymer films was determined by atomic force microscopy.     

两种固体荧光有机-无机杂化物的合成、结构及强红光发射

采用（E）-4-（4-（diphenylamino）styryl）-1-methylpyridinium iodide（DPASPI,DPASP=（E）-4-（4-（diphenylamino）styryl）-1-methylpyridi-nium）,设计合成2种新型有机-无机杂化物（DPASP）₂[Zn（NCS）₄]·2CH₃OH （1）和{（DPASP）₂[Cd（SCN）（NCS）₃]·2CH₃OH}_n （2）。通过单晶X射线衍射进行了表征,结果表明杂化物1和2是由有机吡啶阳离子和异硫氰酸金属配阴离子组成的,具有不同空间结构。通过¹H NMR谱图解释了离子间相互作用。对具有高量子产率的杂化物1和2的红光发光性质进行了研究。     

Blue‐emitting poly(1,3‐phenylenevinylene) derivatives: Effect of substitution patterns on optical properties

Blue‐emitting poly{[5‐(diphenylamino)‐1,3‐phenylenevinylene]‐alt‐(2‐hexyloxy‐5‐methyl‐1,3‐phenylenevinylene)} ( 3 ), poly{[5‐bis‐(4‐butyl‐phenylamino)‐1,3‐phenylenevinylene]‐alt‐(1,3‐phenylene vinylene)} ( 4 ), and poly(2‐hexyloxy‐5‐methyl‐1,3‐phenylenevinylene) ( 5 ) were synthesized by the Wittig–Horner reaction. Although polymers 3–5 possess fluorescent quantum yields of only 13–34% in tetrahydrofuran solution, their films appear to be highly luminescent. Attachments of substituents tuned the emission color of thin films to the desirable blue region (λ_max = 462–477 nm). Double‐layer light‐emitting‐diode devices with 3 and 5 as an emissive layer produced blue emission (λ_em = 474 and 477 nm) with turn‐on voltages of 8 and 11 V, respectively. The external quantum efficiencies were up to 0.13%. © 2005Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2800–2809, 2005     

Stereospecific polymerization of methacrylonitrile. IV. Polymerization by ate complex-type catalysts

Methacrylonitrile was polymerized by a number of ate-complex catalysts. The catalysts used were NaAlR₄, LiAlR₄, LiZnR₃, Li₂ZnR₄, RMg[AlR₄], and Mg[AlR₄]₂. It was found that the ate-complex catalysts in which one of the alkyls is replaced by a diphenylamino group are capable of producing polymers with higher degrees of crystallinity than those of polymers obtained by unmodified catalysts. It was shown that the diphenylamide linkage in these catalytic systems must play an important role in the steric control in the propagation steps of this type of polymerization, although the mechanism is not clear at present. The crystallinity index used in this research gave a linear relation against I measured by NMR, and can be used as a measure of the stereo-regularity of the polymer.     

Intensely Fluorescent Azobenzenes: Synthesis,Crystal Structures,Effects of Substituents,and Application to Fluorescent Vital Stain

2‐[Bis(pentafluorophenyl)boryl]azobenzenes bearing hydrogen, methoxy, dimethylamino, trifluoromethyl, fluoro, n‐butyl, and tert‐butyldimethylsiloxy groups at the 4′‐position or methoxy and bromo groups at the 4‐position have been synthesized. The 4‐bromo group of the 2‐boryl‐4‐bromoazobenzene derivative was converted to phenyl and diphenylamino groups by palladium‐catalyzed reactions. The absorption and fluorescence properties have been investigated using UV/Vis and fluorescence spectroscopy. The 2‐borylazobenzenes emitted an intense green, yellow, and orange fluorescence, in marked contrast to the usual azobenzene fluorescence. The 4′‐siloxy derivative showed the highest fluorescence quantum yield (0.90) among those reported for azobenzenes to date. The correlation between the substituent and the fluorescence properties was elucidated by studying the effect of the substituent on the relaxation process and from DFT and TD‐DFT calculations. An electron‐donating group at the 4′‐position was found to be important for an intense emission. Application of fluorescent azobenzenes as a fluorescent vital stain for the visualization of living tissues was also investigated by microinjection into Xenopus embryos, suggesting these compounds are nontoxic towards embryos.     

Charge transport properties of triphenylamine‐pendant polypeptide

The structurally ordered polymer, triphenylamine‐pendant polypeptide (PATPA: poly[γ‐4‐(N,N‐diphenylamino‐phenyl)‐L ‐glutamine]), was prepared in order to obtain high hole mobility and high thermal stability. The hole mobility obtained for PATPA (ca. 10⁻⁵ cm²/Vsec) at room temperature is higher than that for poly(N‐vinylcarbazole) (PVK) (ca. 10⁻⁷ cm²/Vsec) or that of carbazole‐pendant polypeptide (PCLG) (ca. 10⁻⁸ cm²/Vsec). These results are supported by thermally stimulated current (TSC) measurements because the TSC can be correlated with the mobility. The glass‐transition temperature (T_g) of PATPA was estimated to be about 130° by differential scanning calorimetry (DSC). From these results, PATPA is an alternative candidate as a photoconductive polymer with high thermal stability and high hole mobility. The ordered structure along the main chain is thought to facilitate hole transport. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 362–368, 2000     

Preparation of Fluorescent Polystyrene via ATRP with Dimethylamino Chalcones as Initiator

4‐(3‐(4‐(Dimethylamino)phenyl)acryloyl)phenyl‐2‐bromo‐2‐methylpropanoate (APPBr) was used for the heterogeneous atom transfer radical polymerization (ATRP) of styrene (St) with copper(I) bromide/N,N,N′,N′′,N′′‐pentamethyldiethylenetriamine (PMDETA) catalytic system. The functional end group was characterized via UV‐Vis and ¹H NMR spectra. The polymerization showed a first‐order kinetic characteristic and each of the obtained polymers had well‐controlled molecular weight and relatively low polydispersity index (PDI). Furthermore, the obtained end‐functionalized polystyrene (PS) in solution showed strong green‐light emission which is further affected by mixing different metal cations. In particular, the fluorescent intensity of the polymer was decreased in the presence of Ag⁺, Cu²⁺ and Fe³⁺.     

Structures and photoactive properties of poly(styrene‐co‐vinylbenzophenone)

Poly(styrene‐co‐vinylbenzophenone) prepared by a graft reaction on polystyrene revealed photoactive properties under irradiation of UVA. The photoactive structural features of the polymer were examined via electron paramagnetic resonance (EPR) under irradiation of UVA and fluorescent light. The photoactive functions of the polymer such as antimicrobial performance and dye decolorization ability were investigated. The results revealed that the poly(styrene‐co‐vinylbenzophenone) could generate radicals under fluorescent and UVA irradiation, and some radicals could stay alive for about 30 min in a dark chamber. The photoexcited polymer showed excellent antibacterial ability and decolorization effect on methylene blue and methyl orange dye under both daylight and UVA light. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2423–2430, 2008     

Controlled synthesis and fluorescent properties of poly(9-(4-vinylbenzyl)-9H-carbazole) via nitroxide-mediated living free-radical polymerization

The functional polymer containing carbazole unit, [(poly(9-(4-vinylbenzyl)-9H-carbazole) (PVBK)], was successfully prepared via nitroxide-mediated living free-radical polymerization of 9-(4-vinylbenzyl)-9H-carbazole (VBK). The controlled features of the polymerization were confirmed by the linear increase in the molecular weight with the monomer conversion while keeping the relative narrow molecular weight distribution (M_w/M_n ? 1.51), and successful chain extension with styrene. The resulting polymer absorbed light in the 305-355 nm range and exhibited fluorescent emission at 350 nm. The fluorescent intensity of the polymer was lower than that of monomer and was affected by the properties of the different solvents, which decreased in the following order: DMF > THF > CHCl₃ at the same concentration of carbazole units. The fluorescence intensity of the polymer was apparently influenced by chromophore concentration, and the maximum value was obtained when the carbazole unit concentration was around 8 × 10⁻⁵ mol/L. Moreover, it was shown that the strong fluorescence of PVBK can be quenched by methyl acrylate (MA).     

Photoresponsive self‐assembling structures from a pyrene‐based triblock copolymer

A new photoresponsive amphiphilic triblock copolymer, poly(pyrenylmethyl methacrylate)‐block‐polystyrene‐block‐poly(ethylene oxide) (PPy‐b‐PSt‐b‐PEO), was synthesized using atom‐transfer radical polymerization. Formation of colloidal aggregates of the polymer was observed in solutions under controlled conditions due to the amphiphilic nature of the polymer. Irradiation of the polymer aggregates using UV light resulted in the photodissociation of 1‐pyrenemethanol units from the polymer back‐bone resulting in break‐up of the aggregates mainly due to the hydrophilic nature of the residual polymer. The use of these polymer aggregates to trap hydrophobic fluorescent dyes in water and its controlled release on exposure to UV light has also been explored. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of novel side‐chain triphenylamine polymers with azobenzene moieties via RAFT polymerization and investigation on their photoelectric properties

Two novel and well‐defined polymers, poly[6‐(5‐(diphenylamino)‐2‐((4‐methoxyphenyl)diazenyl)phenoxy)hexyl methacrylate] (PDMMA) and poly[6‐(4‐((3‐ethynylphenyl)diazenyl) phenoxy)hexyl methacrylate] (PDPMMA), which bear triphenylamine (TPA) incorporated to azobenzene either directly (PDMMA) or with an interval (PDPMMA) as pendant groups were successfully prepared via reversible addition‐fragmentation chain transfer polymerization technique. The electrochemical behaviors of PDPMMA and PDMMA were investigated by cyclic voltammograms (CV) measurement. The hole mobilities of the polymer films were determined by fitting the J‐V (current‐voltage) curve into the space‐charge‐limited current method. The influence of photoisomerization of the azobenzene moiety on the behaviors of fluorescence emission, CV and hole mobilities of these two polymers were studied. The fluorescent emission intensities of these two polymers in CH₂Cl₂ were increased by about 100 times after UV irradiation. The oxidation peak currents (I_OX) of the PDMMA and PDPMMA in CH₂Cl₂ were increased after UV irradiation. The photoisomerization of the azobenzene moiety in PDMMA had significant effect on the electrochemical behavior, compared with that in PDPMMA. The changes of the hole mobility before and after UV irradiation were very small for both polymers. The HOMO energies (E_HOMO, HOMO: the highest occupied molecular orbital) of side chain moieties of TPA incorporated with cis‐isomer and trans‐isomer of azobenzene in PDMMA and PDPMMA were obtained by theoretical calculation, which are basically consistent with the experimental results. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Homopolycyclotrimerization of A4‐type tetrayne: A new approach for the creation of a soluble hyperbranched poly(tetraphenylethene) with multifunctionalities

A tetraphenylethene‐containing A₄‐type tetrayne, named 1,1,2,2‐tetrakis(4‐ethynylphenyl)ethene is synthesized and its TaCl₅‐Ph₄Sn catalyzed homopolycyclotrimerization affords hyperbranched poly(tetraphenylethene) with high molecular weight (M_w = 280,000) in high yield (97%). The polymer shows good solubility and high thermal stability. It is aggregation‐enhanced emission (AEE)‐active and functions as a fluorescent chemosensor for explosive detection with a superamplification effect and large quenching constants up to 758,000 M^?1. The polymer shows high and tunable refractive indices (RI = 1.9288?1.6746) in a wide wavelength region. Porous fluorescent polymer thin film is prepared by breath figure (BF) methods and real‐time monitoring of the elusive BF formation process is realized. Photolithography of the thin films readily generates well‐resolved fluorescent photopattern without and with porous secondary structure. The polymer is metallified and pyrolysed to give magnetic ceramics with high magnetic susceptibilities (M_s = 83 emu/g) and near‐zero coercivity (H_c = 0.08 kOe). © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4752–4764     

Photoreactivating Enzyme for (6–4) Photoproducts in Cultured Goldfish Cells

We previously reported that when cultured goldfish cells are illuminated with fluorescent light, photorepair ability for both cyclobutane pyrimidine dimers and (6–4) photoproducts increased. In the present study, it was found that the duration of the induced photorepair ability for cyclobutane pyrimidine dimers was longer than that for (6–4) photoproducts, suggesting the presence of different photolyases for repair of these two major forms of DNA damage. A gel shift assay was then performed to show the presence of protein(s) binding to (6–4) photoproducts and its dissociation from (6–4) photoproducts under fluorescent light illumination. In addition, at 8 h after fluorescent light illumination of the cell, the binding of pro-tein(s) to (6–4) photoproducts increased. The restriction enzymes that have recognition sites containing TT or TC sequences failed to digest the UV-irradiated DNA pho-toreactivated by using Escherichia coli photolyase for cyclobutane pyrimidine dimers, indicating that restriction enzymes could not function because (6–4) photoproducts remained in recognition sites. But, when UV-irradiated DNA depleted of cyclobutane pyrimidine dimers was incubated with extract of cultured goldfish cells under fluorescent light illumination, it was digested with those restriction enzymes. These results suggested the presence of (6–4) photolyase in cultured goldfish cells as in Dro-sophila, Xenopus and Crotalus.     

New High‐Power LEDs Open Photochemistry for Near‐Infrared‐Sensitized Radical and Cationic Photopolymerization

Cyanines derived from heptamethines were investigated in combination with iodonium salts as initiators of the radical polymerization of tripropylene glycol diacrylate and epoxides derived from bisphenol‐A‐diglycidylether. A new near‐infrared (NIR) LED prototype emitting at 805 nm with an exposure intensity of 1.2 W cm^?2 facilitated initiation of both radical and cationic polymerization using sensitizers derived from cyanines. This new light‐emitting device has brought new insight into the photochemistry of cyanines with the general structure 1 because a combination of photonic and thermal processes strongly influences reaction pathways. In particular, cationic cyanines comprising a cyclopentene moiety and diphenylamino group in the center initiated the cationic polymerization of epoxides. Selective oxidation of this unit explains why specifically these derivatives may function as initiators for cationic polymerization. In contrast, when the diphenylamino group was replaced by a barbital group at the meso‐position cationic polymerization of epoxides was not initiated.