Magnetic Fe2O3-polystyrene/PPy core/shell particles: bioreactivity and self-assembly

This paper describes the synthesis of new magnetic, reactive polystyrene/polypyrrole core/shell latex particles. The core consists of a polystyrene microsphere containing gamma-Fe2O3 superparamagnetic nanoparticles (PSmag), and the shell is made of reactive N-carboxylic acid-functionalized polypyrrole (PPyCOOH). These PSmag-PPyCOOH latex particles, average diameter 220 nm, were prepared by copolymerization of pyrrole (Py) and the active carboxyl-functionalized pyrrole (PyCOOH) in the presence of PSmag particles. PNVP was used as a steric stabilizer. The functionalized polypyrrole-coated PSmag particles were characterized in terms of their particle size, surface morphology, chemical composition, and electrochemical and magnetic properties using transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry, and SQUID magnetometry. Activation of the particle surface carboxyl groups was achieved using 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide (EDC) and N-hydroxysuccinimide (NHS), which helps transform the carboxyl groups into activated ester groups (NSE). The activated particles, PSmag-PPyNSE, were further evaluated as bioadsorbents of biotin used as a model biomolecule. It was shown that biotin was immobilized at the surface of the PSmag-PPyNSE particles by forming interfacial amide groups. The assemblies of PSmag-PPyCOOH particles on glass plates were further investigated. When no magnetic field is applied, the particles assemble into 3D colloidal crystals. In contrast, under a magnetic field, one-particle-thick chains gathered in hedgehog-like architectures are obtained. Furthermore, PSmag-PPyCOOH coated ITO electrodes were shown to be electroactive and electrochemically stable, thus offering potentialities for creating novel high-specific-area materials for biosensing devices where the conducting polymer component would act as the transducer through its conductive properties.     

Preparation of functionalized polystyrene latexes by radiation-induced miniemulsion polymerization using a Y-type polymerizable surfactant as sole stabilizers

Functionalized polystyrene latexes were prepared by miniemulsion polymerization using a Y-type polymerizable surfactant bearing a carboxylic acid group as sole stabilizers. Kinetics analysis showed that there was no constant rate stage, which coincided with the kinetics mechanism of the typical miniemulsion polymerization. The latexes obtained were characterized by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) spectroscopy. It was found that the latexes prepared by miniemulsion polymerization initiated by gamma-ray had more narrowly particle size distribution compared with by potassium persulfate. XPS and FTIR results indicated that the carboxyl group was present on the surface of the polymer particles.     

Latex and hollow particles of reactive polypyrrole: preparation, properties, and decoration by gold nanospheres

Polypyrrole-coated polystyrene latex particles bearing reactive N-amino functional groups (PS-PPyNH2) were prepared by the in-situ copolymerization of pyrrole (Py) and the active amino-functionalized pyrrole (PyNH2) in the presence of 1.33 microm-diameter polystyrene (PS) latex particles. These particles were prepared by dispersion polymerization of styrene using poly(N-vinylpyrrolidone), PNVP, as a steric stabilizer. The functionalized polypyrrole-coated PS particles (PS-PPyNH2) were characterized in terms of their particle size and surface morphology using transmission electron microscopy (TEM). Infrared and X-ray photoelectron spectroscopy (XPS) detected pyrrole-NH2 repeat units at the surface of the latex particles, indicating that this monomer had indeed copolymerized with pyrrole. The core-shell structure of the PS-PPyNH2 particles was confirmed by etching the polystyrene core in THF, leading to the formation of hollow conducting polymer capsules. The PS-PPyNH2 particles were then decorated with citrate-stabilized gold nanoparticles via electrostatic interactions. Furthermore, etching of the polystyrene core resulted in the formation of gold-decorated PPyNH2 hollow capsules.     

Polyurethane/polyaniline and polyurethane‐poly(methyl methacrylate)/polyaniline conductive core‐shell particles: Preparation,morphology, and conductivity

Polyurethane/polyaniline (PU/PANI) and polyurethane‐poly(methyl methacrylate)/polyaniline (PU‐PMMA/PANI) conductive core‐shell particles were synthesized by a two‐stage polymerization process. The first stage was to produce a core of PU or PU‐PMMA via miniemulsion polymerization using sodium dodecyl sulfate (SDS) as the surfactant. The second stage was to synthesize the shell of polyaniline over the surface of core particles. Hydrogen chloride (HCl) and dodecyl benzenesulfonic acid (DBSA) were used as the dopant agents. Ammonium persulfate (APS) was used as the oxidant for the polymerization of ANI. Different concentrations of HCl, DBSA, and SDS would cause different conformations of PANI chains and thus different morphologies of PANI particles. UV–visible spectra revealed that the polaron band was blue‐shifted because of the more coiled conformation of PANI chains by increasing the concentration of DBSA. Besides, with a high concentration of DBSA, both spherical‐ and rod‐shape PANI particles were observed by transmission electron microscope, and the coverage of PANI particles onto the core surfaces was improved. The key point of formation of rod‐type PANI particles was that DBSA was served with a high concentration accompanied with the existence of HCl or SDS. The better coverage of PANI particles over the core surfaces by charging higher DBSA concentrations resulted in a higher conductivity of hybrid particles. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3902–3911, 2007     

Heck and Suzuki–Miyaura couplings catalyzed by nanosized palladium in polyaniline

A novel route to prepare polyaniline (PANI)‐supported Pd(0) nanoparticles by a one‐pot chemical route is presented. Nanosized Pd(0) particles were first prepared by reduction of Pd(OAc)₂ using t‐BuONa activated sodium hydride in refluxing THF. A ligand exchange with aniline on t‐BuONa‐stabilized Pd(0) particles yielded aniline‐stabilized particles. Pd(0)/PANI nanocomposites were finally obtained by polymerizing aniline‐stabilized Pd(0) particles using ammonium persulfate. Nanocomposites were characterized by transmission electron microscopy, X‐ray diffraction and X‐ray photoelectron spectroscopy. Results show that this one‐pot experimental route is successful in producing hybrid materials constituted of Pd(0) nanoparticles stabilized by PANI due to the strong binding of PANI amine groups to Pd(0) particles. TEM images of the nanohybrids show that metal particles with diameters of ca. 4.9 nm are homogeneously dispersed in PANI. The preliminary results indicate that the Pd(0) particles supported on PANI behave as efficient heterogeneous catalysts in the Heck and Suzuki–Miyaura reactions of aryl iodides. Copyright © 2005 John Wiley & Sons, Ltd.     

A new approach towards redispersable polyelectrolyte–surfactant complex nanoparticles

Redispersable and weakly cross-linked block copolymer particles with a core-shell structure were prepared by the use of a macroinitiator. Subsequent sulfonation of the polystyrene core and complex formation with a variety of cationic surfactants led to sterically stabilized, redispersable polyelectrolyte-surfactant complex particles with spherical shape and diameters of about 400 nm. Spontaneous microphase separation of the hydrophobic surfactant tails and the hydrophilic entities of the polyelectrolyte and the surfactant headgroups induces mesostructure formation within the particle cores. The characteristic lengths of the mesostructures formed depend mainly on the chain lengths of the surfactants and vary between 2 and 4 nm. For the first time, preformed nanoparticles were used as constrained nanogeometries for polyelectrolyte-surfactant complex formation.     

Polyaniline/Au composite hollow spheres: synthesis, characterization, and application to the detection of dopamine

Polyaniline (PANI)/Au composite hollow spheres were successfully synthesized using polystyrene/sulfonated polystyrene core/shell gel particle templates. The PANI shell thickness and the number of Au nanoparticles decorating the PANI could be controlled effectively by adjusting the experimental conditions. The morphology, composition, and optical properties of the resulting products were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, thermogravimetric analysis, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and ultraviolet-visible absorption spectra. It was found that the electrical conductivity of the PANI/Au composite hollow spheres was more than 3 times higher than that of the pure PANI hollow spheres. Furthermore, PANI/Au composites were immobilized on the surface of a glassy carbon electrode (GCE) and applied to construct a sensor. The obtained PANI/Au-modified GCEs showed one pair of redox peaks and high catalytic activity for the oxidation of dopamine. The possible formation mechanism of the PANI/Au composite hollow spheres was also discussed.     

Study of emulsion polymerization stabilized by amphiphilic polymer nanoparticles

Submicron-sized polystyrene (PS) microspheres with a relatively narrow particle size distribution can be easily produced through emulsion polymerization induced by γ-ray at room temperature using a new type of amphiphilic cross-linked poly(stearyl methacrylate-co-acrylamide-co-acrylic acid) particles as stabilizer. The properties of these amphiphilic particles were described, including morphology, size, ζ potential, and contact angles. The effect of the pH value and the content of amphiphilic particles on the formation and stability of emulsions were also investigated. Meanwhile, the obtained PS microspheres were characterized by Fourier transform infrared spectroscopy, transmission electron microscopy, scanning electron microscopy and X-ray photoelectron spectroscopy. In addition, through observing the morphology and size of emulsion droplets at different times under an optical microscope, we found it is interesting that Pickering emulsions formed initially disappeared gradually, which is different from the common Pickering emulsions stabilized by inorganic particles. Thus, the mechanism was further discussed.     

Electrochemical preparation of distinct polyaniline nanostructures by surface charge control of polystyrene nanoparticle templates

A family of nanostructured polyaniline (PANI) materials including polystyrene (PS)/PANI core/shell particles, PANI hollow spheres, PANI/PS nanocomposite and nanoporous PANI, were conveniently prepared by surface charge control of PS nanoparticle templates which resulted in different polymer growth mechanisms when PANI was electropolymerized around the templates.     

Fabrication of a novel glucose biosensor based on a highly electroactive polystyrene/polyaniline/Au nanocomposite

A novel nanocomposite with a core-shell structure containing polystyrene (PS), polyaniline (PANI), and Au nanoparticles (NPs) was synthesized. The nanocomposite was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FTIR). Cyclic voltammetric experiments indicated that the nanocomposite had excellent redox ability in a wide range of pH values. The existence of Au NPs resulted in a higher electrical conductivity of the nanocomposite. As a model, glucose oxidase (GOD) was entrapped onto the nanocomposite-modified glassy carbon electrode (GCE) and applied to construct a sensor. The immobilized GOD showed a pair of well-defined redox peaks and high catalytic activity for the oxidation of glucose.     

On the structure and electrical conductivity of polyaniline/polystyrene blends prepared by an aqueous‐dispersion blending method

This article describes electrically conductive polymer blends containing polyaniline‐dodecyl benzene sulfonic acid (PANI‐DBSA) dispersed in a polystyrene (PS) matrix or in crosslinked polystyrene (XPS). Melt blending of previously mixed, coagulated, and dried aqueous dispersions of PANI‐DBSA and PS latices lead to high conductivities at extremely low PANI‐DBSA concentrations (∼0.5 wt % PANI‐DBSA). In these blends, the very small size of the PANI‐DBSA particles and the surface properties (with surfactants used) of both the PANI and polymer particles play a major role in the PANI‐DBSA particle structuring process. The PANI‐DBSA behavior is characteristic of a unique colloidal polymeric filler with an extremely high surface area and a strong interaction with the matrix, evidenced by a significantly higher glass‐transition temperature of the matrix. The effect of the shear level on the conductivity and morphology of the PS/PANI‐DBSA blends was studied by the production of capillary rheometer filaments at various shear rates. An outstanding result was found for XPS/PANI‐DBSA blends prepared by the blending of aqueous XPS and PANI‐DBSA dispersions. Some of these blends were insulating at low shear levels; however, above a certain shear level, smooth surface filaments were generated, with dramatically increased and stable conductivities. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 611–621, 2001     

Facile preparation of monodisperse hollow cross‐linked chitosan microspheres

We have successfully prepared biocompatible and biodegradable hollow microspheres using carboxyl‐functionalized polystyrene particles as core template and the chitosan cross‐linked with glutaraldehyde as the shell. The monodisperse carboxyl‐functionalized polystyrene particles were made by emulsifier‐free emulsion polymerization. The structure, morphology, and constitution of the carboxyl‐functionalized polystyrene particles were characterized by FTIR, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X‐ray photoelectron spectroscopy (XPS). The structure, morphology, and formation process of the hollow cross‐linked chitosan microspheres were characterized by FTIR, SEM, and TEM. The results revealed that the latex particles were removed by exposed to solvent and the microspheres exhibited the hollow structure. This work confirmed that the hollow microspheres were accomplished by fabricating on the basis of chemical cross‐linking on the surface of the carboxyl‐functionalized polystyrene particles and then removing off the cores of particles. Moreover, with the increase of carboxyl‐functionalization degree at the surface of latexes and the increase of cross‐linking period, the thicker and firmer monodisperse hollow microspheres were obtained. In addition, a water‐soluble drug, salicylic acid, encapsulated in the microcapsules slowly released at pH 1.2. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 228–237, 2008     

Fabrication of zinc oxide/poly(styrene) grafted nanocomposite latex and its dispersion

Zinc oxide nanoparticles, with an average size of about 40 nm, were encapsulated by polystyrene using in situ emulsion polymerization in the presence of 3-methacryloxypropyltrimethoxysilane (MPTMS) as a coupling agent and polyoxyethylene nonylphenyl ether (OP-10) as a surfactant. Polymerization mechanism of nanocomposite latex was discussed. Transmission electron microscopy (TEM) proved the presence of ZnO nanoparticle appeared to be monodisperse in nanosize in polymer composite particles. ZnO/PS nanocomposites were characterized by Fourier transform infrared spectra (FT-IR), X-ray photoelectron spectroscopy (XPS), thermo-gravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results of FT-IR and XPS revealed that the surface of ZnO particle was successfully grafted by PS through the link of the coupling agent between ZnO and polymer. TGA and DSC results indicated an enhancement of thermal stability of composite materials compared with the pure polymer. SEM (scanning electron microscope) images showed a perfect dispersion of the ZnO particles in latex film. In addition, UV-visible absorption measurements demonstrated that the ZnO/PS composite coatings display a perfect performance of absorbing UV light.     

Nonionic latices in aqueous media part 1. Preparation and characterization of polystyrene latices

A series of non-ionic polystyrene latices in aqueous media containing particles with a narrow size distribution have been prepared using a nonyl phenol poly(ehylene glycol) condensate as the surfactant, methoxy poly(ethylene glycol methacrylate) as the comonomer/stabilizer, and ascorbic acid/hydrogen peroxide as the initiator system. As a control synthesis for comparison with the above latex, a charge stabilized polystyrene latex was prepared, using an anionic surfactant and potassium persulphate as the initiator. Latices employing a combination of charge plus steric stabilization mechanisms were also prepared, in order to investigate the effect of the non-ionic surfactant and the comonomer/stabilizer. The particle size of the latices was measured by transmission electron microscopy, the surface charge density by conductimetric titration and the glass transition temperature of the polymer by differential scanning calorimetry. The latex prepared using non-ionic ingredients, showed no titratable charge and exhibited a profound lowering of the glass transition temperature, with respect to the charge stabilized latex. On the basis of these results, schematic models for the polymerization mechanism and the morphology of the latex particles are proposed.     

Emulsion polymerization of styrene and methyl methacrylate using a hydrophobically modified inulin and comparison with other surfactants

The use of a new class of graft polymer surfactants, based on inulin, in emulsion polymerization of poly(methyl methacrylate) (PMMA) and polystyrene (PS) particles is described. PS and PMMA were synthesized by emulsion polymerization, and stable particles with a high monomer content (50 wt %) were obtained with a very small amount of polymeric surfactant ([surfactant]/[monomer] = 0.0033). The latex dispersions were characterized by dynamic light scattering and by transmission electron microscopy to obtain the average particle size and the polydispersity index, and the stability was determined by turbidimetry measurements and expressed in terms of critical coagulation concentration. The last section gives a comparison of PMMA particles prepared by emulsion polymerization using classical surfactants from different types as emulsifiers with that obtained using the copolymer surfactant. It shows the superiority of INUTEC SP1 as it is the only one that allows stable particles at 20 wt % monomer content, with a smaller ratio [surfactant]/[monomer] = 0.002.     

Surface modification and particles size distribution control in nano-CdS/polystyrene composite film

Preparation of nano-CdS particles with surface thiol modification by microemulsion method and their influences on the particle size distribution in highly filled polystyrene-based composites were studied. The modified nano-CdS was characterized by X-ray photoelectron spectroscopy (XPS), light absorption and emission measurements to reveal the morphologies of the surface modifier, which are consistent with the surface molecules packing calculation. The morphologies of the surface modifier exerted a great influence not only on the optical performance of the particles themselves, but also on the size distribution of the particle in polystyrene matrix. A monolayer coverage with tightly packed thiol molecules was believed to be most effective in promoting a uniform particle size distribution and eliminating the surface defects that cause radiationless recombination. Control of the particles size distribution in polystyrene can be attained by adjusting surface coverage status of the thiol molecules based on the strong interaction between the surface modifier and the matrix.     

聚苯胺纳米点阵列的制备和库仑台阶现象

本文制备了PANI纳米点阵列, 利用导电原子力显微镜(C-AFM)表征了其形貌和导电性能, 在室温下观察到PANI纳米点的库仑台阶(Coulomb staircase)现象, 并利用库仑阻塞效应的理论进行了初步的分析.     

Synthesis and characterization of single‐wall‐carbon‐nanotube‐doped emeraldine salt and base polyaniline nanocomposites

Nanocomposites of polyaniline (PANI) and single‐wall carbon nanotubes (SWNTs) were prepared and characterized via resonance Raman and electronic absorption spectroscopy (ultraviolet–visible/near‐infrared). The chemical synthesis of PANI was performed in the presence of SWNTs in concentrations ranging from 10 to 50 wt % (SWNT/PANI). The obtained materials were hydrophilic, homogeneous composite compounds. The chemical interaction between PANI (in the conducting emeraldine salt form and in the insulating emeraldine base form) and metallic and semiconducting nanotubes was investigated. The emeraldine salt form of the polymer was significantly stabilized in the composite in comparison with plain PANI. A selective electronic interaction process between PANI and metallic SWNTs was found. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 815–822, 2005     

单分散核／壳结构导电高分子复合材料的研究（Ⅰ）——单分散核／壳结构聚苯乙烯／聚吡咯的结构表征

导电高分子在光、电、磁等领域表现出的广泛应用前景 ,使它成为材料科学的研究热点 .然而 ,早期发现的导电高分子的不溶不熔性 ,使它在可加工性和机械性能等方面仍面临许多挑战 .核 /壳结构导电高分子与单分散技术的结合 ,无疑为这一领域的研究带来新的生机和活力 .目前仅有的少量文献主要集中报道微米和亚微米级单分散核 /壳导电高分子复合材料的研究 ,大多采用种子乳液聚合法合成 .微米级的种子乳液通常采用以醇为分散介质的分散聚合方法制备 [1～ 3] ,由于种子分散体系要经反复离心分离 ,除去醇类 ,重新分散在水相中再进行核 /壳导电高分…     

Preparation and structural characterization of polymer-supported methylrhenium trioxide systems as efficient and selective catalysts for the epoxidation of olefins

Novel heterogeneous compounds of methylrhenium trioxide (MTO) were prepared with poly(4-vinylpyridine) and polystyrene as polymeric supports. The wide-angle X-ray diffraction (WAXS.) analysis, performed by the application of the difference method, showed, in a representative case of the poly(4-vinylpyridine)/MTO derivatives, a slightly distorted octahedral conformation on the metal's primary coordination sphere. The Re-O and Re-C bond distances were not influenced by the polymeric nature of the ligand, while the Re-N bond distance was abnormally shorter than those previously observed for homogeneous MTO/L(n) complexes, showing a strong coordination of the rhenium atom to the support. A set of scanning electron microscopy (SEM) photographs showing the morphology of the surface of particles of poly(4-vinylpyridine)/MTO and polystyrene/MTO systems are reported. The reticulation grade of the polymer was a crucial factor for the morphology of the particles surface. Poly(4-vinylpyridine) 2% cross-linked systems were characterized by particles with very irregular shape and surface. Poly(4-vinylpyridine) 25% cross-linked systems showed particles with regular spherical shape, which morphology was similar to microcapsules obtained with polystyrene. All novel MTO compounds were efficient and selective heterogeneous catalysts for the epoxidation of olefins using environmentally friendly H2O2 as oxygen atom donor. The catalyst activity was maintained for at least five recycling experiments.