Preparation and characterization of amine-functionalized SiO2/TiO2 films for formaldehyde degradation

This paper investigated the gaseous formaldehyde degradation by the amine-functionalized SiO₂/TiO₂ photocatalytic films for improving indoor air quality. The films were synthesized via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and 3-aminopropyltrimethoxysilane (APTMS). The physicochemical properties of prepared photocatalysts were characterized with N₂ adsorption/desorption isotherms measurement, X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FT/IR). The effect of amine-functional groups and the ratio of MTMOS/APTMS precursors on the formaldehyde adsorption and photocatalytic degradation were investigated. The results showed that the formaldehyde adsorption and photocatalytic degradation of the APTMS-functionalized SiO₂/TiO₂ film was higher than that of SiO₂/TiO₂ film due to the surface adsorption on amine sites and the relatively high of the specific surface area of the APTMS-functionalized SiO₂/TiO₂ film (15 times higher than SiO₂/TiO₂). The enhancement of the formaldehyde degradation of the film can be attributed to the synergetic effect of adsorption and subsequent photocatalytic decomposition. The repeatability of photocatalytic film was also tested and the degradation efficiency was 91.0% of initial efficiency after seven cycles.     

Photocatalytic decomposition of methylene blue and 4-chlorophenol on nanocrystalline TiO2 films under UV illumination: A ToF-SIMS study

The photocatalytic degradation of methylene blue and 4-chlorophenol on nanocrystalline TiO₂ (nc-TiO₂) under UV irradiation was investigated by time-of-flight secondary ion mass spectrometry (ToF-SIMS). Nanocrystalline TiO₂ films were prepared from suspensions containing TiO₂-crystallites of different average sizes, the smallest one being 12 nm. The organic substances (either methylene blue or 4-chlorophenol) were applied to these films. The specimens were studied in the pristine state and upon UV exposure. The UV illuminations were carried out both under atmospheric conditions and in situ under ultrahigh vacuum in the ToF-SIMS instrument. Distinct mass signals from the parent molecules and from fragment ions are observed for the as-prepared samples. Upon irradiation with UV light under atmospheric conditions, the surface composition is significantly changed, an observation ascribed to photocatalytic reactions induced by UV photons: the parent molecule signals are strongly diminished whereas fragmentation products are identified to be present at the TiO₂ surfaces. UV irradiations carried out under different vacuum conditions in the ToF instrument (ultrahigh vacuum, air or oxygen adsorption) indicate that varying ambient conditions may influence the photocatalytic reaction on the nanocrystalline TiO₂ films.     

Improvement of photocatalytic behavior of chemical-vapor-synthesized TiO2 nanopowders by post-heat treatment

Anatase-type TiO₂ nanopowders less than 10 nm in average diameter were synthesized by a chemical vapor synthesis method. The TiO₂ nanopowders showed very poor photocatalytic properties, in spite of their large surface area. With subsequent heat treatment of the TiO₂ powders, their photocatalytic properties determined by measuring the degradation of 2-propanol were improved at temperatures up to 600 °C and then diminished along with formation of a rutile phase. This improvement in the photocatalytic properties of TiO₂ nanopowders was attributed to both a morphology change and a change in the electronic surface characteristics of TiO₂ particles during heat treatment.     

Preparation of visible light responsive N doped TiO2 via a reduction-nitridation procedure by nonthermal plasma treatment

A visible light responsive N-doped TiO₂ was prepared via a reduction-nitridation procedure by nonthermal plasma treatment. X-ray diffraction, N₂ adsorption, UV-vis spectroscopy, photoluminescence, and X-ray photoelectron spectroscopy were used to characterize the prepared TiO₂ samples. The plasma treatment did not change the phase composition and particle sizes of TiO₂ samples, but extended its absorption edges to the visible light region. The photocatalytic activities were tested in the degradation of an aqueous solution of a reactive dyestuff, methylene blue, under visible light. The photocatalytic activities of TiO₂ prepared by reduction-nitridation procedure were much higher than that of samples prepared by simple nitridation treatment. The enhanced activity was ascribed to the substitutional N-doping and appropriate concentration of oxygen vacancies. TOHN10 prepared by reduction-nitridation procedure exhibited excellent photocatalytic stability. A possible mechanism for the photocatalysis was proposed.     

Surface effect of natural zeolite (clinoptilolite) on the photocatalytic activity of TiO2

The surface interaction between TiO₂ and natural zeolite, clinoptilolite, has been investigated by means of transmission electron microscope (TEM), atom force microscope (AFM), X-ray diffractometer (XRD), diffuse reflectance infrared Fourier transform (DRIFT) and far Fourier transform infrared ray (FTIR) spectroscopy. And the photocatalytic degradation (PCD) rate of methyl orange (MO), a model of recalcitrant azo dye, in aqueous system has been measured to compare the photocatalytic activities of different photocatalysts. A model has been carried out to explain the incorporation between TiO₂ particles and natural zeolite. The results show that the TiO₂ particles loaded on zeolite are 50 nm or so, smaller than the pure one, and combine with zeolite via chemical force. Since the reserved adsorption ability and the existence of electron trapper, the TiO₂-zeolite performed more efficient at low initial concentration and in the later period of PCD process, as compared with pure TiO₂ nanopowders.     

One-step solvothermal preparation of TiO2/C composites and their visible-light photocatalytic activities

Preparation of anatase type titania nanoparticles and their carbon modification were synchronously achieved by the solvothermal method with glycerol as the carbon source. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and diffuse reflectance spectra (DRS). It was found that the glycerol/ethanol ratio affected significantly the morphology and properties of TiO₂/C composites. The TiO₂/C composite which was obtained in the solution with the glycerol/ethanol ratio of 5/75, contained 1.2 mass% carbon and exhibited both superior adsorption capability and visible-light photocatalytic activity. Contrary to this, samples prepared in the solution with higher glycerol/ethanol ratio, exhibited lower photocatalytic activity similar to that of the titania without carbon modification. It was suggested that excess addition of glycerol might contribute to large amounts of carbonaceous species and severe aggregation of the as-prepared samples, and thus reduced the surface area. As a result, the adsorption capability and visible-light photocatalytic activity increased at first and then decreased with the increase of glycerol addition. Present study provided a facile one-step method to obtain TiO₂/C composites with a controllable carbon content and photocatalytic performance under mild temperature.     

Influence of the OH groups on the photocatalytic activity and photoinduced hydrophilicity of microwave assisted sol-gel TiO2 film

In the present work the influence of the OH groups on the photocatalytic activity and the photoinduced hydrophilicity of microwave assisted sol-gel TiO₂ films was investigated. The prepared TiO₂ films were characterized using XRD and AFM. Furthermore, the surface of the TiO₂ films was examined by help of XPS in order to determine the amount of OH groups before and after UV irradiation at different humidities. The activity of the TiO₂ films was determined using stearic acid as a model compound and the photoinduced superhydrophilicity was investigated through contact angle measurements.The results of this investigation showed that the microwave assisted sol-gel technique produces highly homogeneous and efficient TiO₂ films without the need for heat treatment for crystallization. Based on the conducted experiments it is suggested that the amount of OH groups on the TiO₂ surface highly influence the photocatalytic activity and the photoinduced superhydrophilicity and that the two mechanisms may be closely related. It is suggested that the superhydrophilicity is obtained through a combination of photocatalytic degradation of organic contaminants and surface structural changes in form of an increased amount of OH-groups.     

Photocatalytic behavior of heavy La-doped TiO2 films deposited by pulsed laser deposition using non-sintered target

We have investigated the control of photocatalytic behavior under deposited conditions of non-sintered target of different molar ratios with TiO₂ and La₂O₃ from 1:0 to 1:2 for heavily La doping, and post-annealing temperature from 600 °C to 1000 °C for crystallizing by pulsed laser deposition. We have successfully crystallized heavily La-doped TiO₂ films with post-annealing temperature over 800 °C and with molar ratio of TiO₂:La₂O₃ over 1:1 on a quartz substrate. Heavily La-doped TiO₂ films are observed the decomposition of methylene blue and a water-splitting reaction in photocatalytic behavior under Xe light irradiation. When stoichiometric La-doped TiO₂ (TiO₂:La₂O₃ = 1: 1) is synthesized with heat-treatment at 900 °C, the best results are obtained under photocatalytic behavior and pure La₂Ti₂O₇ crystalline were obtained.     

Synthesis and photocatalytic properties of porous TiO2 films prepared by ODA/sol-gel method

Porous TiO₂ films were deposited on SiO₂ pre-coated glass-slides by sol-gel method using octadecylamine (ODA) as template. The amount of ODA in the sol played an important role on the physicochemical properties and photocatalytic performance of the TiO₂ films. The films prepared at different conditions were all composed of anatase titanium dioxide crystals, and TiO₂ crystalline size got larger with increasing ODA amount. The maximum specific surface area of 41.5 m²/g was obtained for TiO₂ powders prepared from titanium sol containing 2.0 g ODA. Methyl orange degradation rate was enhanced along with increasing ODA amount and reached the maximal value at 2.0 g addition of ODA. After 40 min of UV-light irradiation, methyl orange degradation rate reached 30.5% on the porous film, which was about 10% higher than that on the smooth film. Porous TiO₂ film showed almost constant activity with slight decrease from 30.5% to 28.5% after 4 times of recycles.     

Comparison of photocatalytic performance of anatase TiO2 prepared by low and high temperature route

Anatase TiO₂ was prepared by a facile sol-gel method at low temperature through tailoring the pH of sol-gel without calcination. As a control, anatase TiO₂ was also synthesized by the conventional sol-gel process, in which calcination at 500 °C was required to transform the amorphous oxide into highly crystalline anatase. As-prepared samples were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy (PL). Their photocatalytic activities were evaluated by degradation of methyl orange under UV light irradiation. On the basis of experiment results, it could be concluded that TiO₂ prepared by low temperature route showed more advantages in small particle size, highly dispersion nature, abundance of surface hydroxyl groups, strong PL signal, and high photocatalytic activity over TiO₂ obtained by the conventional sol-gel process. Furthermore, the reason of the former possessing higher photocatalytic activity was discussed.     

Photocatalytic Activities of Boron Doped Titanium Dioxide Nanoparticles and its Composite with Polyaniline

Abstract

Titanium dioxide (TiO₂) was doped with a nonmetalic element, boron (B), and the boron doped TiO₂ (B-TiO₂) was combined with polyaniline (Pani) through an in-situ polymerization technique. The photocatalytic activity of the prepared samples was monitored by the degradation of methylene blue under UV light irradiation. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy were used to reveal the effect of boron doping on the crystalline and chemical structure of the photocatalyst, respectively. The morphological and elemental compositional characteristics of the samples were evaluated using field emission scaning electron microscopy (FE-SEM) and energy dispersive x-ray analysis. The optical band gap energy of the prepared samples was obtained by UV-Visible (UV-Vis) spectroscopy. B-TiO₂ exhibited enhanced photocatalytic performance compared to the undoped photocatalyst. Furthermore, compared with TiO₂ and B-TiO₂, Pani/B-TiO₂ displayed superior photocatalytic activity. The composite achieved almost 26% methylene blue degradation within 150?minutes. Although the boron doping enhanced the crystallinity of TiO₂ slightly, it did not affect the morphology. FTIR confirmed the presence of tri-coordinated interstitial boron in the Ti–O–B bonds. The UV-Vis spectra displayed a red shift with the incorporation of the boron atoms. The incorporation of the boron atoms in the TiO₂ crystal structure are suggested to promote the separation of the photoinduced electron-hole pairs, a possible reason for the enhanced photocatalytic activity. B-TiO₂ and its composite with polyaniline could be considered as a promising photocatalyst to remove organic dyes from the wastewater.     

Tunable photocatalytic selectivity of fluoropolymer PVDF modified TiO2

Fluoropolymer poly-vinylidene-fluoride modified TiO₂ (PVDF/TiO₂) were prepared via a simple chemisorption approach and characterized by thermo gravimetric analyse, transmission electron microscope, X-ray diffraction, X-ray photoelectron spectroscopy and photoluminescence spectra. The modified mechanism and the photocatalytic selectivity of the PVDF/TiO₂ were studied. The existence of Ti-F coordination bond on the interface between TiO₂ and PVDF was confirmed. For the PVDF modification, the photocatalytic degradation (PCD) of cationic dye was greatly enhanced, and the PCD of anionic dye was obviously inhibited. PVDF/TiO₂ shows high photocatalytic selectivity than that of TiO₂ by degrading mixed solution of cationic dyes MB and anionic dyes MO. The selectivity can be tuned by changing the PVDF modification amount.     

Oblique angle deposition of TiO2 thin films prepared by electron-beam evaporation

Optical, structural and photocatalytic properties of TiO₂ thin films obliquely deposited on quartz glass substrate using an electron-beam evaporation method were investigated. The photocatalytic activity of the films was evaluated by photodecomposition of methylene blue. An increase in incident deposition angle increased the porosity and surface roughness of the TiO₂ films. As a result, the photocatalytic activity was enhanced with incident deposition angle up to 60°. However, a further increase in incident deposition angle to 75° reduced the photocatalytic activity due to a lack of the crystalline phase.     

Different effects of cerium ions doping on properties of anatase and rutile TiO2

Pure and Ce⁴⁺ doped anatase and rutile TiO₂ were prepared by hydrothermal methods and characterized by XRD, TEM, UV-vis diffusion spectroscopy, and XPS measurements. The photocatalytic reactivity of the catalysts was evaluated by the photodegradation of Rhodamine B (RB) under ultraviolet irradiation. The photocatalytic efficiency of the rutile sample doped with an appropriate amount of Ce⁴⁺ was enhanced while all Ce⁴⁺ doped anatase samples showed a much lower activity than pure anatase. The reasons were discussed     

Characterization and photocatalytic activity of Zn–TiO2/AC composite photocatalyst

Activated carbon (AC) supported Zn²⁺–TiO₂ photocatalyst was prepared by sol–gel method. The prepared samples were characterized by X-ray diffraction, scanning electron micrograph, nitrogen absorption, diffuse reflectance UV/VIS and X-ray photoelectron spectroscopy. Using toluene as a pollution target, the photocatalytic activity of photocatalyst was evaluated. The results showed that prepared photocatalyst was obviously helpful for the removal of toluene in air. The photocatalytic degradation of toluene by Zn²⁺–TiO₂/AC reached 100% for 40 min and remained 75% after 160 min, while degradation by TiO₂ was only 30%. It indicated that the photocatalytic activity of prepared photocatalyst was enhanced. It is due to Zn²⁺-doping increased the oxidation and reduction of hole–electron pairs, which was the important factor in heterogeneous photocatalysis.     

Enhanced photocatalytic activity of TiO2 nano-structured thin film with a silver hierarchical configuration

TiO₂ sol-gels with various Ag/TiO₂ molar ratios from 0 to 0.9% were used to fabricate silver-modified nano-structured TiO₂ thin films using a layer-by-layer dip-coating (LLDC) technique. This technique allows obtaining TiO₂ nano-structured thin films with a silver hierarchical configuration. The coating of pure TiO₂ sol-gel and Ag-modified sol-gel was marked as T and A, respectively. According to the coating order and the nature of the TiO₂ sol-gel, four types of the TiO₂ thin films were constructed, and marked as AT (bottom layer was Ag modified, surface layer was pure TiO₂), TA (bottom layer was pure TiO₂, surface layer was Ag modified), TT (pure TiO₂ thin film) and AA (TiO₂ thin film was uniformly Ag modified). These thin films were characterized by means of linear sweep voltammetry (LSV), X-ray diffraction (XRD), scanning electron microscopy (SEM), electrochemical impedance spectroscopy and transient photocurrent (I_ph). LSV confirmed the existence of Ag⁰ state in the TiO₂ thin film. SEM and XRD experiments indicated that the sizes of the TiO₂ nanoparticles of the resulting films were in the order of TT > AT > TA > AA, suggesting the gradient Ag distribution in the films. The SEM and XRD results also confirmed that Ag had an inhibition effect on the size growth of anatase nanoparticles. Photocatalytic activities of the resulting thin films were also evaluated in the photocatalytic degradation process of methyl orange. The preliminary results demonstrated the sequence of the photocatalytic activity of the resulting films was AT > TA > AA > TT. This suggested that the silver hierarchical configuration can be used to improve the photocatalytic activity of TiO₂ thin film.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

Study of effect annealing temperature on the structure, morphology and photocatalytic activity of Si doped TiO2 thin films deposited by electron beam evaporation

Transparent Si-doped TiO₂ thin films (Si-TiO₂) were deposited on quartz glasses using electron beam evaporation (EBE) and annealed at different temperature in an air atmosphere. The structure and morphology of these films were analyzed by X-ray diffraction (XRD), Raman microscopy (Raman), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). Meanwhile the photocatalytic activity of the films has also been evaluated on the basis of the degradation degree of rhodamine B in aqueous solution. Our experimental results suggest that the annealing temperature impact a strong effect on the structure, morphology and photocatalytic activity of Si-TiO₂ thin films. Furthermore the enhanced thermal stability of Si-TiO₂ films enabled them to elevate the phase transformation temperature of TiO₂ from anatase to rutile and enhanced the photocatalytic efficiency.     

Room temperature ferromagnetism in vacuum-annealed TiO2 thin films

Thin films of pure TiO₂ have been prepared using both spin-coating and sputter-deposition techniques on sapphire and quartz substrates. The structural characteristics of the films have been investigated in detail using Raman spectroscopy and high-resolution transmission electron microscopy (HRTEM). When annealed in vacuum, all films demonstrate room temperature ferromagnetism, while the air-annealed samples show much smaller, often negligible, magnetic moments. The magnetization of the vacuum-annealed sputtered samples depends on film thickness, with the volume magnetization decreasing monotonically with increasing thickness. Furthermore, the magnetization per unit area also decreases slightly with increasing film thickness. These results suggest that ferromagnetism in the vacuum-annealed TiO₂ films is mediated by surface defects or interfacial effects, but does not arise from stoichiometric crystalline TiO₂.     

Preparation and photo-induced superhydrophilicity of composite TiO2-SiO2-In2O3 thin film

In this work, TiO₂-SiO₂-In₂O₃ composite thin films on glass substrates were prepared by the sol-gel dip coating process. X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF) and X-ray photoelectron spectroscopy (XPS) were used to evaluate the structural and chemical properties of the films. UV-vis spectrophotometer was used to measure the transmittance spectra of thin films. The water contact angle (WCA) of thin films during UV/vis irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that fabrication of composite film has a significant effect on transmittance and superhydrophilicity of TiO₂ films.