In situ preparation of hydrophobic CaCO3 in the presence of sodium oleate

Hydrophobic CaCO₃ particles were directly prepared via carbonation of Ca(OH)₂ slurry in the presence of sodium oleate at room temperature. Sodium oleate was used to modify the surface property of CaCO₃ particles. The measurement of relative contact angle and active ratio indicated that CaCO₃ samples were hydrophobic. DTG, FT-IR and TEM analysis of the obtained product indicated that the hydrophobic property was attributed to the deposition of calcium oleate, produced in the reaction mixture, onto the surface of calcium carbonate particles. They were covered on the CaCO₃ crystals surface and modified their surface property; at the same time they own CC bonds and could be polymerized or copolymerized later to give a polymeric monolayer.     

Biomimetic nucleation and growth of hydrophobic vaterite nanoparticles with oleic acid in a methanol solution

Hydrophobic vaterite nanoparticles were prepared via crystallization of CaCO₃ with oleic acid in methanol by mimicking the process of biomineralization. The molar ratio of oleic acid to calcium ion was varied from 0.1 to 0.5. By changing the concentration of the oleic acid, CaCO₃ particles with different shapes and polymorphism were obtained. High concentration of the oleic acid gave stable vaterite crystals, the polymorph of which did not change when the composite was kept in water for more than one week. Fourier transform infrared spectroscopy (FT-IR) and TGA analysis of the obtained product indicated that the oleic acid was bound to the crystalline CaCO₃. The contact angle of the modified vaterite reached 122°. We have succeeded in crystallization of hydrophobic CaCO₃ nanoparticles in situ.     

Improved aging performance of vapor phase deposited hydrophobic self-assembled monolayers

A hydrophobic self-assembled monolayer (SAM) of fluoro-octyl-trichloro-silane (FOTS) was deposited on silicon using a vapor phase technique. The aging of the hydrophobic layer was examined using water contact angle measurements. It has been found that while such monolayer films suffer from a loss of hydrophobicity with time, pre-immersion nitrogen annealing can significantly improve the aging characteristics of these monolayers. The effect of nitrogen annealing on the improved aging properties of SAM coatings has been investigated by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The hydrolytic stability and the effect of nitrogen annealing were studied by morphological evolution during immersion. A spontaneous formation of silane mounds on the surface of the monolayers was found by AFM. These mounds have been irreversibly transformed from initially uniform hydrophobic surface layers. It is highly probable that the compliance of these mounds can reasonably allow hydrophilic sites to be located around the mounds. Interestingly, the density of these mounds formation is very less on the annealed samples. XPS reveals a higher level of coverage by the N₂-annealed film due to agglomeration. A relative abundance of CF₃ and CF₂ moieties in the annealed film may explain the enhancement of the hydrophobicity as revealed by higher level of water contact angle. This hydrophobicity was found to be significantly stable in water. This novel finding explains the improved hydrophobic stability of FOTS monolayers as primarily a morpho-chemical effect that originates from the densification of the monolayers upon annealing.     

Organic-inorganic hybrid superhydrophobic surfaces using methyltriethoxysilane and tetraethoxysilane sol-gel derived materials in emulsion

By applying alkaline-catalyzed co-hydrolysis and copolycondensation reactions of tetraethoxysilane (TEOS) and methyltriethoxysilane (MTES) in organic siloxane modified polyacrylate emulsion (OSPA emulsion), we are able to demonstrate the potential for developing a sol-gel derived organic-inorganic hybrid emulsion for a superhydrophobic surface research. TEOS and MTES derived sol-gel moieties can be designed for a physical roughness and hydrophobic characteristic (Si-CH₃) of the hybrid superhydrophobic surface, while OSPA emulsion can be endowed for good film-forming property. The effect of formulation parameters on superhydrophobicity and film-forming property was analyzed. The water contact angle (WCA) on the sol-gel derived hybrid film is determined to be 156°, and the contact angle hysteresis is 5° by keeping the mole ratio of TEOS:MTES:C₂H₅OH:NH₃·H₂O:AMP-95 at 1:4:30:10:0.63 and the mass percentage of OSPA emulsion at 25%. The nanoparticle-based silica rough surface is observed as the mole ratio of MTES/TEOS at 4:1. The sol-gel derived organic-inorganic hybrid emulsion shows remarkable film-forming property when the mole ratio of MTES/TEOS reaches or exceeds 4:1. With the primer coating, the performance of superhydrophobic film achieve actual use standard. It reveals that this new procedure is an effective shortcut to obtain a superhydrophobic surface with potential applications.     

A novel method to fabricate superhydrophobic surfaces based on well-defined mulberry-like particles and self-assembly of polydimethylsiloxane

A superhydrophobic surface was obtained by combining application of CaCO₃/SiO₂ mulberry-like composite particles, which originated from violent stirring and surface modification, and self-assembly of polydimethylsiloxane. Water contact angle and sliding angle of the superhydrophobic surface were measured to be about 164 ± 2.5° and 5°, respectively. The excellent hydrophobicity is attributed to the synergistic effect of micro-submicro-nano-meter scale roughness (fabricated by composite particles) and the low surface energy (provided by polydimethylsiloxane). This procedure makes it possible for widespread applications of superhydrophobic film due to its simplicity and practicability.     

Improvement of polyacrylate coating by filling modified nano-TiO2

Nano-TiO₂ is modified by a method, by which nano-TiO₂ first reacts with silane coupling agent WD-70 with double bond group which subsequently copolymerizes with methyl methacrylate and butyl acrylate to produce a thin polymer shell on the nanoparticles. The modified nanoparticles have stable organophilicity. They are applied to polyacrylate coating and performances of the coating are measured by different methods. The modification of nano-TiO₂ particles can improve their dispersibility in coating, enhance hardness of coating and reduce water absorption and permeability of polyacrylate coating. The mechanism has been analyzed in this paper.     

TMOS based water repellent silica thin films by co-precursor method using TMES as a hydrophobic agent

The present paper describes the room temperature synthesis of dip coated water repellent silica coatings on glass substrates using trimethylethoxysilane (TMES) as a co-precursor. Silica sol was prepared by keeping the molar ratio of tetramethoxysilane (TMOS) precursor, methanol (MeOH) solvent, water (H₂O) constant at 1:29.27:2.09 respectively, with 0.5 M NH₄OH throughout the experiments and the TMES/TMOS molar ratio (M) was varied from 0 to 3.8. It was found that with an increase in M value, the roughness and hydrophobicity of the films increased, however the optical transmission decreased from 93% to 57% in the visible range. The hydrophobic silica films retained their hydrophobicity up to a temperature of 250 °C and above this temperature the films became hydrophilic. The hydrophobic silica thin films were characterized by taking into consideration the surface roughness studies, Fourier transform infrared (FT-IR) spectroscopy, percentage of optical transmission, scanning electron microscopy (SEM) and contact angle measurements.     

Effect of Filler Treatment on Crystallization,Morphology and Mechanical Properties of Polypropylene/Calcium Carbonate Composites

Pimelic acid (PA) was used as a new surface modifier for CaCO₃. The effects of PA treatment on the crystallization, morphology, and mechanical properties of PP/CaCO₃ composites were investigated. Fourier transform infrared (FTIR) spectroscopy analysis revealed that PA bonded to CaCO₃ and formed a calcium pimelate surface layer after reacting with CaCO₃. The results of wide angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), and polarized light microscopy (PLM) proved that the PA treated CaCO₃ induced a large amount of β -iPP and decreased the spherulitic size of PP. The results of scanning electron microscopy (SEM) showed that the PA treatment enhanced the interfacial adhesion between the filler and the matrix, indicating the improvement of the compatibility between PP and CaCO₃. The toughness of the composites was improved by the more ductile β -form spherulites. When 1% of PA treated CaCO₃ was added, the notched impact strength reached its maximum, a value of 19.79 kJ/m², which was 3.64 times greater than that of the pure PP.     

Preparation and characterization of slice-like Cu2(OH)3NO3 superhydrophobic structure on copper foil

Superhydrophobic structure was prepared on copper foil via a facile solution-immersion method. Thus slice-like Cu₂(OH)₃NO₃ crystal was prepared on the surface of the copper foil by sequential immersing in an aqueous solution of sodium hydroxide and cupric nitrate. And the superhydrophobic structure was obtained by modifying the slice-like Cu₂(OH)₃NO₃ crystal with 1H,1H,2H,2H-perfluorodecyltriethoxysilane (FAS-17). The morphologies, chemical compositions and states, and hydrophobicity of the surface-modifying films on the copper foil substrates were analyzed by means of scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and water contact angle measurement. Moreover, the thermal stability of the slice-like structure was also evaluated using thermogravimetric analysis (TGA). It was found that roughening of the copper foil surface helped to increase the hydrophobicity to some extent, but no superhydrophobicity was obtained unless the slice-like Cu₂(OH)₃NO₃ crystal formed on the Cu substrate was modified with 1H,1H,2H,2H-perfluorodecyltriethoxysilane. Besides, the superhydrophobicity of the FAS-17-modified slice-like Cu₂(OH)₃NO₃ structure was closely related to the surface morphology. And this hydrophobic structure retained good superhydrophobic stability at elevated temperature and in long-term storage as well, which should be critical to the application of Cu-matrix materials in engineering.     

Enhancement in hydrophobicity of silica films using metal acetylacetonate and heat treatment

Water is one of the most affecting chemicals that can cause damage to the solid surface. To protect the surface due to the action of water, the surface should be made hydrophobic. In the present study, the improvement in hydrophobicity of silica films using metal acetylacetonate (M-acac) by employing heat treatment to methyltrimethoxy silane (MTMS) based silica coatings is reported as a novel attempt. Instead of following the established trends of the surface derivatization or co-precursor method, iron acetylacetonate Fe(acac)₃, copper acetylacetonate Cu(acac)₂ and heat treatment were used to incorporate hydrophobicity with silica coatings. As M-acac is readily soluble in organic solvents, Fe(acac)₃ and Cu(acac)₂ were dissolved in methanol (MeOH) and their concentration was varied from 0 to 0.025 M. The coating solution was prepared by optimizing molar ratio of MTMS:MeOH:basic H₂O to 1:7.15:6.34, respectively. Gelation time (t_g) for Cu(acac)₂ containing silica sol and that containing Fe(acac)₃ were noted to be 30 and 55 min, respectively. The substrates were taken out after gelation and heat treated at 150 °C for 2 h. The heat treated films showed a dramatic increase in the static water contact angle from 82° to as high as 142°.     

Bouncing behaviors of suspension liquid drops on a superhydrophobic surface

Abstract  

This paper reveals three patterns of bouncing behaviors of suspension drops containing calcium carbonate (CaCO₃) powder on a superhydrophobic surface with the aid of a high-speed camera. In transmission electron microscopy (TEM) observation, the particles of CaCO₃ are shaped like sticks whose equivalent diameters are about 700 nm. Unlike a pure water drop, dense suspension drops cannot be pinched off at the bounce on the superhydrophobic surface due to a high effective viscosity, whereas the equilibrium contact angle appears to be almost identical in all kinds of droplets.     

Synthesis and characterization of superhydrophobic functionalized Cu(OH)2 nanotube arrays on copper foil

Superhydrophobic functionalized cupric hydroxide (Cu(OH)₂) nanotube arrays were prepared on copper foils via a facile alkali assistant surface oxidation technique. Thus nanotube arrays of Cu(OH)₂ were directly fabricated on the surface of copper foil by immersing in an aqueous solution of NaOH and (NH₄)₂S₂O₈. The wettability of the surface was changed from surperhydrophilicity to superhydrophobicity by chemical modification with 1H,1H,2H,2H-perfluorodecyltriethoxysilane (FAS). The morphologies, microstructures, crystal structure, chemical compositions and states, and hydrophobicity of the films on the copper foil substrates were analyzed by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and water contact angle measurement. It was found that the rough structure of the surface helped to magnify the wettability. The static contact angle (CA) for water is larger than 160° and the contact angle hysteresis (CAH) is lower than 5° on the modified surface. The high roughness of the nanotube arrays along with the generated C-F chains by chemical modification contributed to the improved superhydrophobicity. The present research is expected to be significant in providing a new strategy for the preparation of novel multifunctional materials with potential industrial applications on copper substrates.     

Molecular dynamics simulation of wetting on modified amorphous silica surface

The microscopic wetting of water on amorphous silica surfaces has been investigated by molecular dynamics simulation. Different degrees of surface hydroxylation/silanization were considered. It was observed that the hydrophobicity becomes enhanced with an increase in the degree of surface silanization. A continuous transformation from hydrophilicity to hydrophobicity can be attained for the amorphous silica surfaces through surface modification. From the simulation result, the contact angle can exceed 90° when surface silanization percentage is above 50%, showing a hydrophobic character. It is also found that when the percentage of surface silanization is above 70% on the amorphous silica surface, the water contact angle almost remains unchanged (110–120°). This phenomenon is a little different from the wetting behavior on smooth quartz plates in previous experimental report. This change in the wettability on modified amorphous silica surfaces can be interpreted in terms of the interaction between water molecules and the silica surfaces.     

Effect of iron doping on the hydrophobicity of titanium dioxide film: experiment and simulation

In this study, we carried out experiments and molecular dynamics simulations to identify the effect of Fe doping on the hydrophobicity of a titanium dioxide film. TiO₂ and Fe-doped TiO₂ films were fabricated in situ by atomic layer deposition without annealing. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to characterise the crystal structure and elemental composition. Iron doping resulted in the TiO₂ becoming more hydrophobic at a macroscopic level, as estimated by atomic force microscopy observations and static contact angle measurements. Furthermore, the effect of iron doping on the structure and kinetics of water molecules on the exterior of TiO₂ were studied by molecular dynamics simulations. On the basis of the XPS results, the Fe-TiO₂ surface matrix has a Ti:Fe ratio of 36:5. In addition, the density distribution of oxygen and hydrogen atoms indicate that interfacial water molecules enter the Fe-TiO₂ film more easily and hydrogen atoms in the water molecules are oriented upward at the interface. The self-diffusion coefficients indicate that iron doping makes the TiO₂ more hydrophobic, which is consistent with the macroscopic test results.     

Super-hydrophobicity and oleophobicity of silicone rubber modified by CF4 radio frequency plasma

Owing to excellent electric properties, silicone rubber (SIR) has been widely employed in outdoor insulator. For further improving its hydrophobicity and service life, the SIR samples are treated by CF₄ radio frequency (RF) capacitively coupled plasma. The hydrophobic and oleophobic properties are characterized by static contact angle method. The surface morphology of modified SIR is observed by atom force microscope (AFM). X-ray photoelectron spectroscopy (XPS) is used to test the variation of the functional groups on the SIR surface due to the treatment by CF₄ plasma. The results indicate that the static contact angle of SIR surface is improved from 100.7° to 150.2° via the CF₄ plasma modification, and the super-hydrophobic surface of modified SIR, which the corresponding static contact angle is 150.2°, appears at RF power of 200 W for a 5 min treatment time. It is found that the super-hydrophobic surface ascribes to the coaction of the increase of roughness created by the ablation action and the formation of [-SiF_x(CH₃)_2−x-O-]_n (x = 1, 2) structure produced by F atoms replacement methyl groups reaction, more importantly, the formation of [-SiF₂-O-]_n structure is the major factor for super-hydrophobic surface, and it is different from the previous studies, which proposed the fluorocarbon species such as C-F, C-F₂, C-F₃, CF-CF_n, and C-CF_n, were largely introduced to the polymer surface and responsible for the formation of low surface energy.     

Superhydrophobic alumina surface based on stearic acid modification

A novel superhydrophobic alumina surface is fabricated by grafting stearic acid layer onto the porous and roughened aluminum film. The chemical and phase structure, morphology, and the chemical state of the atoms at the superhydrophobic surface were investigated by techniques as FTIR, XRD, FE-SEM, and XPS, respectively. Results show that a super water-repellent surface with a contact angle of 154.2° is generated. The superhydrophobic alumina surface takes on an uneven flowerlike structure with many nanometer-scale hollows distribute in the nipple-shaped protrusions, and which is composed of boehmite crystal and γ-Al₂O₃. Furthermore, the roughened and porous alumina surface is coated with a layer of hydrophobic alkyl chains which come from stearic acid molecules. Therefore, both the roughened structure and the hydrophobic layer endue the alumina surface with the superhydrophobic behavior.     

Tailoring the wettability of nanocrystalline TiO2 films

The water contact angle (WCA) of nanocrystalline TiO₂ films was adjusted by fluoroalkylsilane (FAS) modification and photocatalytic lithography. FAS modification made the surface hydrophobic with the WCA up to ∼156°, while ultraviolet (UV) irradiation changed surface to hydrophilic with the WCA down to ∼0°. Both the hydrophobicity and hydrophilicity were enhanced by surface roughness. The wettability can be tailored by varying the concentration of FAS solution and soaking time, as well as the UV light intensity and irradiation time. Additionally, with the help of photomasks, hydrophobic-hydrophilic micropatterns can be fabricated and manifested via area-selective deposition of polystyrene particles.     

Organic modification of TEOS based silica aerogels using hexadecyltrimethoxysilane as a hydrophobic reagent

The experimental results on the synthesis and characterization of tetraethoxysilane (TEOS) based hydrophobic silica aerogels using hexadecyltrimethoxysilane (HDTMS) as a hydrophobic reagent by two step sol-gel process, are described. The molar ratio of tetraethoxysilane (TEOS), methanol (MeOH), acidic water (0.001 M, oxalic acid) and basic water (10 M, NH₄OH) was kept constant at 1:55:3.25:1.25 and the molar ratio of HDTMS/TEOS (M) was varied from 0 to 28.5 × 10⁻². The organic modification was confirmed by infrared spectroscopic studies, and the hydrophobicity of the aerogels was tested by the contact angle measurements. The maximum contact angle of 152° was obtained for M = 22.8 × 10⁻². The aerogels retained the hydrophobicity up to a temperature of 240 °C and above this temperature the aerogels became hydrophilic. The aerogels were characterized by the thermal conductivity, density, contact angle measurements, optical transmission and scanning electron micrographs.     

Hydrophobic Modification of Poly(Ethylene Terephthalate) with Epoxy-Modified Polysiloxane by Reactive Extrusion

Hydrophobic poly(ethylene terephthalate) (PET) was prepared by reactive blending of PET with double epoxy groups modified polysiloxane (diepsi) or multiepoxy groups modified polysiloxane (multiepsi). The structure of the modified PET was characterized by ¹H NMR and intrinsic viscosity. The grafted ratio of diepsi and multiepsi was 1.3 and 0.03 wt%, respectively. With the introduction of diepsi and multiepsi to PET, the water contact angle of modified PET increased from 73° to a maximum of 106°, showing the good hydrophobicity of the modified PET. The samples of modified PET were washed with different solvents and their water contact angles did not significantly decrease, indicating good durability of the hydrophobicity. Moreover, the films of modified PET prepared by solution casting (phenol and 1, 1, 2, 2-tetrachloroethane mixed solution) showed excellent hydrophobicity with the contact angle 151°. Scanning electron microscopy images showed the surface of the modified PET films to be rougher than those of unmodified PET because the introduction of polysiloxane to PET resulted in phase separation during the solvent evaporation process.     

Transparent water repellent silica films by sol-gel process

Non-wettable surfaces with high contact angles and facile sliding angle of water droplets have received tremendous attention in recent years. The present paper describes the room temperature (∼27 °C) synthesis of dip coated water repellent silica coatings on glass substrates using iso-butyltrimethoxysilane (iso-BTMS) as a co-precursor. Emphasis is given to the influence of the hydrophobic reagent (iso-BTMS) on the water repellent properties of the silica films. Silica sol was prepared by keeping the molar ratio of tetraethoxysilane (TEOS) precursor, methanol (MeOH) solvent, water (H₂O) constant at 1:16.53:8.26 respectively, with 0.01 M NH₄F throughout the experiment and the molar ratio of iso-BTMS/TEOS (M) was varied from 0 to 0.965. The effect of M on the surface structure and hydrophobicity has been researched. The static water contact angle values of the silica films increased from 65° to 140° and water sliding angle values decreased from 42° to 16° with an increase in the M value from 0 to 0.965. The water repellent silica films are thermally stable up to a temperature of 280 °C and above this temperature the film shows hydrophilic behavior. The water repellent silica films were characterized by the Fourier Transform Infrared (FT-IR) Spectroscopy, Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM), % of optical transmission, thermal and chemical aging tests, humidity tests, static and dynamic water contact angle measurements.