Synthesis and characterization of Cr doped CdS nanoparticles stabilized with polyvinylpyrrolidone

Undoped and Cr (2 and 4 at.%) doped CdS nanoparticles were synthesized in aqueous solution by simple chemical co-precipitation method using polyvinylpyrrolidone (PVP) as stabilizer. The prepared nanoparticles were examined using X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDAX), transmission electron microscopy (TEM), UV-vis diffuse reflectance spectroscopy (DRS) and Fourier transform infrared spectroscopy (FTIR). XRD pattern of the nanoparticles showed cubic zincblende phase with the particle size of the order of 3-4 nm, which was in good agreement with the results obtained from TEM studies. The EDAX analysis confirmed that Cd, Cr and S elements were present in the samples and the variations between the target and actual compositions were microscopic. UV-vis DRS spectra of the samples exhibited decrease in the band gap which further attests the incorporation of Cr into CdS nanoparticles. FTIR studies revealed that the undoped as well as Cr doped CdS nanoparticles were capped by polyvinylpyrrolidone.     

Study of nano-CdS prepared in methanolic solution and polymer electrolyte matrix

This present paper reports the study of cadmium sulphide (CdS) nanoparticles prepared under controlled condition in methanolic solution and also in polyethylene oxide polymer electrolyte matrix. The sulphurations of the cadmium salts were done in situ by a sodium sulphide solution. The concentration of the precursors has been controlled as detailed in the paper. All the preparation and characterization were carried out at room temperature. The nanoparticles were characterized by UV/Vis spectra in the range of 600 to 250 nm. The absence of bulk/micron size particles was noted in either of the system. The absorption edge near 510 nm indicates the presence of bulk CdS, whereas the presence of nanometer-sized particles is also reflected in low wavelength region. The sizes of the particles as well as particle distribution have been estimated using X-ray diffraction and scanning electron microscopy, respectively. A comparison in the spectra has been done for the sample prepared in either of the matrices. The particle size distribution in the polymeric matrix has been found to be more in comparison to that in the methanolic suspension. The polymer is reported to work as a binder, but not as a capping agent.     

Large Third-Order Optical Nonlinearity of Cadmium Sulphide Nanoparticles Embedded in Polymer Thin Films

A simple method for synthesis of well dispersed cadmium sulphide nanoparticles embedded in a polyethylene glycol matrix （PEG 400） in thin film form is presented. The large blue shift of the band gap energy of the CdS nanoparticles compared to the bulk semiconductors is observed via UV-vis absorption spectra. Photoluminescence spectra of CdS nanocomposite films show that the emission peaks shift towards the longer wavelength with the increase of annealing temperature. Transmission electron microscopic images as well as Raman scattering studies confirm the CdS nanometer size particle formation within the polymer matrix. The particle size is about 8 nm. Selected area electron diffraction （SAED） shows the cubic zinc blende polycrystalline rings. Third-order optical nonlinearity of the CdS nanopartieles embedded in polymer thin films is studied with the Z-scan technique under 1064 nm excitation. The results show that the CdS nanocomposite film exhibits negative nonlinear refraction index and positive absorption coefficient. The film shows large optical nonlinearity, and the magnitude of the third-order nonlinear susceptibility of the film is calculated to be 1.73 × 10^-9 esu. The corresponding mechanism is discussed.     

Cadmium sulfide quantum dots stabilized by castor oil and ricinoleic acid

Castor oil and ricinoleic acid (an isolate of castor oil) are environmentally friendly bio-based organic surfactants that have been used as capping agents to prepare nearly spherical cadmium sulfide quantum dots (QDs) at 230, 250 and 280 °C. The prepared quantum dots were characterized by Ultra violet–visible (UV–vis), Photoluminescence (PL), Transmission Electron Microscopy (TEM), High Resolution Transmission Electron Microscopy (HRTEM) and X-ray diffraction (XRD) giving an overall CdS QDs average size of 5.14±0.39 nm. The broad XRD pattern and crystal lattice fringes in the HRTEM images showed a hexagonal phase composition of the CdS QDs. The calculated/estimated average size of the prepared castor oil capped CdS QDs for various techniques were 4.64 nm (TEM), 4.65 nm (EMA), 5.35 nm (UV–vis) and 6.46 nm (XRD). For ricinoleic acid capped CdS QDs, the average sizes were 5.56 nm (TEM), 4.78 nm (EMA), 5.52 nm (UV–vis) and 8.21 nm (XRD). Optical properties of CdS QDs showed a change of band gap energy from its bulk band gap of 2.42–2.82 eV due to quantum size confinement effect for temperature range of 230–280 °C. Similarly, a blue shift was observed in the photoluminescence spectra. Scanning electron microscope (SEM) observations show that the as-synthesized CdS QDs structures are spherical in shape. Fourier transform infra-red (FTIR) studies confirms the formation of castor oil and ricinoleic acid capped CdS QDs.     

Structural and optical characterization of CdS nanoparticles prepared by chemical precipitation method

In the present study we have synthesized CdS semiconducting quantum dots by the chemical precipitation method using Thioglycerol as the capping agent. X-ray powder diffraction (XRD) and transmission electron microscopy (TEM) are employed to characterize the size, morphology and crystalline structure of the as-prepared material. The synthesized QPs have a mixture of cubical and hexagonal crystal symmetry with 12 nm average diameter. Ultraviolet-visible (UV-vis) absorption spectroscopy is used to calculate the band gap of the material and blue shift in absorption edge. Confinement of the optical phonon modes in the QPs is studied by Raman spectroscopy, while FTIR for identification of chemical bonds in the nanomaterial. Multiple cadmium and sulphur defects were observed by employing the photoluminescence (PL) method.     

The effect of annealing temperature on structural and optical properties of undoped and Cu doped CdS thin films

Cadmium sulphide (CdS) thin films were prepared chemical bath deposition technique. The films were doped with copper using the direct method consisting in the addition of a copper salt in the deposition bath of CdS. The doped films were annealed in air, at 250, 300 and 350 °C, for 1 h. The deposition films were characterized with X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive analysis by X-rays (EDAX) and optical properties of CdS thin films before and after Cu doping. XRD analysis shows that the films are polycrystalline in nature with cubic crystalline structure. The various parameters such as crystallite size, micro strain and dislocation density were evaluated. SEM study shows that the total substrate surface is well covered by uniformly distributed spherical shaped grains. Optical transmittance study shows the presence of direct transition with band gap energy decrease 2.5–2.2 eV.     

Light emitting CdS quantum dots in PMMA: Synthesis and optical studies

Freshly prepared CdS-quantum dots (QDs) in DMF (clear pale solution) when loaded in polymethylmethacrylate (PMMA) lead to excellent optical properties. The tuning of the absorption and emission wavelengths via experimentally control parameters is considered novel and significant. The absorption band for CdS was observed at about 370 nm in polymeric matrix. The blue, green and orange light emissions from such composite solution were tuned and stabilized by simply varying the concentration of CdS, cadmium and sulphur in the final product. Photoluminescence (PL) measurement with 2% CdS loading showed band-edge emissions from the composite with only about 20-25 nm Stokes shift in emission wavelength. Observation of such optical properties indicated that the composite has narrow particle size distribution and particle diameter may well be below 10 nm. X-ray diffraction (XRD) patterns of the film with higher loading of CdS showed broad pattern for hexagonal CdS. Thermo-gravimetric analysis (TGA) of CdS/PMMA composite film revealed that it has better thermal stability than PMMA alone. Transmission electron microscopy (TEM) showed agglomerated tiny dots in nano-meter regime.     

A mathematical model to predict the grain size of nanocrystalline CdS thin films based on the deposition condition used in the sol–gel spin coating method

Design of experiment (DOE) based on central composite design (CCD) has been employed for the development of a mathematical model correlating the important process parameters like thiourea concentration (U), annealing temperature (A), rotational speed (S), and annealing time (T) of the spin coating process for the preparation of CdS thin films. The experiments were conducted as per the design matrix. Nanocrystalline CdS thin films have been prepared using cadmium nitrate and thiourea as precursors by sol gel spin coating method using the results of the mathematical model. The prepared CdS films have been characterized and the crystal structure and grain size of the samples were analyzed using X-ray diffraction technique. The adequacy of the developed models was checked by analysis of variance (ANOVA) technique. The accuracy of prediction has been carried out by conducting confirmation test. Using this model, the main effect of process parameters on grain size of CdS films have been studied. These parameters were optimized to obtain minimum grain size using the Microsoft excel solver. The results have been verified by depositing CdS films using the optimized conditions. These films have been characterized using X-ray diffraction technique and the grain size is found to be 8.8 nm. The high resolution transmission electron microscopy (HRTEM) analysis showed the grain size of the prepared CdS film to be ∼7 nm. UV–vis spectroscopy analysis revealed that CdS films exhibited quantum confinement effect.     

Synthesis of cellulose nanocrystals (CNCs) from cotton using ultrasound-assisted acid hydrolysis

This present work reports the synthesis of Cellulose nanocrystals (CNCs) from cotton using an ultrasound-assisted acid hydrolysis. Further, the synthesized CNCs was comprehensively characterized using Fourier Transform Infrared Spectroscopy (FTIR) to analyze surface functional groups and X-ray diffraction (XRD) in studying structural characteristics. Differential Thermal Analysis (DTA) and Thermogravimetric Analysis (TGA) have been used to study the thermal properties of CNCs. Morphology of CNCs was studied using a Transmission Electron Microscope (TEM) and Scanning Electron Microscope (SEM). The crystallite size was found to be 10–50 nm using XRD data and the average particle size to be 221 nm using PSD analysis.     

Structural and optical properties of Mn doped ZnS semiconductor nanostructures

Manganese doped zinc sulphide nanoparticles were fabricated by adopting an inexpensive solution growth route. Different samples were fabricated by varying Mn concentrations. UV-VIS study reveals blue-shift on the onset of absorption and hence enhancement in the optical band gap upto 0.75 eV, indicating strong quantum confinement. Photoluminescene study for all the samples display characteristic band edge peak at ∼410 nm. The broad peak ∼560–580 nm is ascribed to Mn incorporation. Further, structural investigations were carried out by using X-Ray diffraction and transmission electron microscopy (TEM).     

Synthesis, structural and optical characterization of nanocrystalline ZnS:Cu embedded in silica matrix

The synthesis of Cu doped ZnS nanoparticles inside the pore of an inorganic silica gel matrix is presented. The synthesized nanoparticles were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX). X-ray diffraction pattern reveals the crystalline wurtzite phase of ZnS. The existence of silica gel in modeling morphologies of the nanoparticles was characterized using Fourier transform infrared (FTIR) spectrometer. Thickness of the silica shell was also calculated. UV- absorption spectrum shows the appearance of an absorption peak at 273 nm which confirms the blue shift as compared to that of bulk ZnS. The photoluminescence (PL) emission spectrum of the sample showed a broad band in the range 465-510 nm due to the transition from the conduction band edge of ZnS nanocrystals to the acceptor like t₂ state of Cu.     

Controlled synthesis, characterization and optical properties of CdS nanocrystalline thin films via chemical bath deposition (CBD) route

In this study, the CdS nanocrystalline thin films obtained from an ammonia-free chemical bath deposition process. The crystallites with a size range of 10–20 nm in diameter with zinc blend (cubic) and wurtzite (hexagonal) crystal structure and strong photoluminescence were prepared from the mixture solutions of: cadmium chloride dihydrate as a cadmium source, thiourea as a sulfur source and sodium citrate dihydrate as a complexing agent for cadmium ions. The well-cleaned glass used as a substrate for thin films deposition. The obtained samples were characterized by the techniques such as scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS), atomic force microscopy (AFM) and fluorescence spectroscopy. Also, the effect of two parameters such as pH and temperature of reaction on the synthesis of CdS nanocrystals was studied. Finally, it was found the CdS nanocrystals showed sharp excitation features and strong “band-edge” emission.     

Photoluminescence of CdS nanoparticles embedded in a starch matrix

CdS nanoparticles were synthesized by precipitation in aqueous solution using starch as the capping molecule, and the effect of the pH of the solution on the optical absorption, photoluminescence, and size of the nanoparticles was studied. Absorption spectra, obtained by photoacoustic spectroscopy, indicated that the band gap energy of the crystalline nanoparticles decreased from 2.68 eV down to 2.48 eV by increasing the pH of the solution from 9 up to 14. The X-ray diffraction analysis revealed that the CdS nanoparticles were of zinc blende structure, and that the particle size increased from 1.35 nm up to 2.45 nm with increasing pH. In addition, temperature-dependent photoluminescence (PL) measurements of the capped material showed a blue-shift of the emission peak for temperatures higher than 150 K, indicating the influence of starch on the formation of defect levels on the surface of the CdS nanoparticles.     

Study of energy transfer from capping agents to intrinsic vacancies/defects in passivated ZnS nanoparticles

The study of energy transfer mechanism from different capping agents to intrinsic luminescent vacancy centres of zinc sulphide (ZnS) has been reported in the present work. Nanoparticles of capped and uncapped ZnS are prepared by co-precipitation reaction. These nanoparticles are sterically stabilized using organic polymers—poly vinyl pyrrolidone, 2-mercaptoethanol and thioglycerol. Monodispersed nanoparticles were observed under TEM for both capped and uncapped ZnS nanopowders. However, for uncapped ZnS nanopowders, tendency for formation of nanorod like structure exists. Size of ZnS crystallites was calculated from X-ray diffraction pattern. The primary crystallite size estimated from X-ray diffraction pattern is 1.95–2.20 nm for capped nanostructures and 2.2 nm for uncapped nanostructures. FTIR spectra were conducted to confirm capping. Zeta potential measurements have been done to check the stability of dispersed nanoparticles. Band gap measurement was done by UV–visible spectrophotometer. Excitation and emission spectra are also performed in order to compare optical properties in various samples. Increase in emission intensity and band gap has been observed by adding different capping agents in comparison to uncapped ZnS nanoparticles. The results show that in capped ZnS nanoparticles the mechanism of energy transfer from capping layer to photoluminescent vacancy centres is more pronounced.     

Synthesis of CdS nanostructures using template-assisted ammonia-free chemical bath deposition

CdS micro- and nano-structures (micro/nanotubes and nanostructured films) were obtained by ammonia-free chemical bath deposition using polymer templates (ion track-etched polycarbonate membranes and poly(styrene-hydroxyethyl methacrylate) nanosphere arrays). The semiconductor structures were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), optical absorption, photoluminescence and electrical measurements. The diameters of CdS tubes are between 300 nm and few microns and the lengths are up to tens of micrometers. The SEM images prove that the CdS films are nanostructured due to the deposition on the polymer nanosphere arrays. For both CdS structures (tubes and films) the XRD patterns show a hexagonal phase. The optical studies reveal a band gap value of about 2.5?2.6 eV and a red luminescence at ～1.77 eV. A higher increase of conductivity is observed for illuminating the CdS nanostructured film when compared to the simple semiconductor film. This is a consequence of the periodic patterning induced by the polymer nanosphere array.     

Formation of CdS nanoparticles using starch as capping agent

CdS nanoparticles have been synthesized using starch as capping agent in aqueous solution. The morphology and crystalline structure of such samples were measured by high-resolution transmission electron microscopy and X-ray diffraction, respectively. The average grain size of the nanoparticles determined by these techniques was of the order of 5 nm. Photoluminescence of CdS nanoparticles shows a strong emission peak below to the band gap bulk semiconductor attributed to center trap states, also the broadening peak was interpreted in terms of electron-phonon interaction.     

CdS quantum dot-sensitized ZnO nanorod-based photoelectrochemical solar cells

ZnO nanorods have been grown using ZnO seed layer onto ITO-coated glass substrates. CdS quantum dots have been deposited onto ZnO nanorods using simple precursors by chemical method and the assembly of CdS quantum dots with ZnO nanorod has been used as photo-electrode in quantum dot-sensitized solar cells. X-ray diffraction results show that ZnO seed layer, ZnO nanorods, and CdS quantum dot-sensitized ZnO nanorods exhibit hexagonal structure. The particle size of CdS nanoparticle is 5 nm. The surface morphology studied using scanning electron microscope shows that the top surface of the vertically aligned ZnO nanorods is fully covered by CdS quantum dots. The ZnO nanorods have diameter ranging from 100 to 200 nm. The absorption spectra reveal that the absorption edge of CdS quantum dot-sensitized ZnO nanorods shift toward longer wavelength side when compared to the absorption edge of ZnO. The efficiency of the fabricated CdS quantum dot-sensitized ZnO nanorod-based solar cell is 0.69% and is the best efficiency reported so far for this type of solar cells.     

Study of structure and optical luminescence of C+6 (80 MeV) ion irradiated CdS: Fe system

Iron doped CdS nanocrystals have been synthesized by using aqueous solution precipitation method. Samples of CdS:Fe have been subjected to irradiation using C⁺⁶ (80 MeV) under of 1×10¹³ ions/cm². For characterization, X-ray diffraction (XRD), Photoluminescence (PL) and Optical absorption studies have been performed. The system has been found in hexagonal phase having particle size distribution 18–20 nm. Photoluminescence intensity has been found to decrease, while optical band gap has been found to increase in irradiated samples.     

Optical Properties of CdS–PVA Nanocomposites

Semiconductor–polymer nanocomposites, with good control over the nanoparticle size and their dispersion within the polymer matrix, can have applications in many optical and luminescent display devices. Cadmium sulphide (CdS) is the most popular semiconductor nanoparticle exhibiting size dependent properties due to its large exciton binding energy and its suitability for large scale production. The nanoparticles need to be passivated against aggregation with suitable capping agents, without sacrificing the desirable properties like transparency and flexibility of the polymer. Cadmium sulphide nanoparticles capped with polyvinyl pyrrolidone (PVP) are synthesized using cadmium nitrate (Cd(NO₃)₂) and hydrogen sulphide (H₂S) as Cd²⁺ and S^2– sources, respectively. CdS particles with sizes in the range of 5–6 nm are prepared in methanol and the solvent is removed using a rotary evaporator. CdS powder is dispersed in polyvinyl alcohol (PVA) solution with dimethyl formamide (DMF) as solvent to get (PVP–CdS)–PVA nanocomposite film of about 0.2 mm thickness. This has been characterized by powder X-ray diffraction (XRD), optical absorption studies, transmission electron microscopy (TEM), differential scanning calorimetry (DSC) and photoluminescence (PL). Particle size does not change due to incorporation in the polymer matrix and the polymer retains its transparency and flexibility. The nanocomposite shows good photoluminescence property with stronger band edge emission than defect related emission. The latter could be quenched completely by optimizing the PVP content. Irradiation of the nanocomposite with 8 MeV electrons at a dose of 100 kGy could effectively quench the defect related emission.     

Role of deposition temperature and Sn content on structural,optical & electrical properties of In2O3 thin films

High quality indium tin oxide (ITO) thin films (In_2−xSn_xO₃: x = 0, 0.1 and 0.2) have been grown by using pulsed laser deposition technique on quartz substrates. The structural, morphological, optical and electrical investigations of deposited films have been studied as a function of substrate deposition temperatures and the Sn compositions. X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM) patterns affirm that each film is polycrystalline in nature with cubic bixbyite single phase structure which preferentially oriented along (222) Miller plane. The existence of chemical bonding and functional groups was investigated by FTIR spectroscopy. The TEM micrograph of films (@450°C) for x = 0.1 and x = 0.2 reveal spherical morphology with average particle size 63 nm and 51 nm, respectively. The SEM and AFM images show uniform flower like surface morphology and well-demonstrated nanosized spherical particles, respectively. The widening of the band gap of all the films were exclusively defined by Burstein-Moss shift. The Hall measurement reveals that each film is degenerate with n-type semiconducting nature along with high mobility. Low resistivity (2.024 × 10⁻⁴ Ω-cm) and high transparency (92.58%) along with high carrier concentration (8.915 × 10²⁰ cm⁻³) were optimized for x = 0.1 film at 450°C deposition temperature.