Microstructure characterization of mechanosynthesized nanocrystalline NiFe2O4 by Rietveld's analysis

Nanocrystalline nickel ferrite (NiFe₂O₄) is synthesized at room temperature by high-energy ball milling the stoichiometric mixture of (1:1 mol%) of NiO and α-Fe₂O₃ powders. The structural and microstructural evolution of NiFe₂O₄ caused by milling is investigated by X-ray powder diffraction. The relative phase abundance, particle size, r.m.s. strain, lattice parameter changes of different phases have been estimated employing Rietveld structure refinement analysis of X-ray powder diffraction data. Particle size and content (wt%) of both NiO and α-Fe₂O₃ phases reduce rapidly with increasing milling time and a significant amount of nanocrystalline NiFe₂O₄ is formed within 1 h of ball milling. Particle sizes of all the phases reduce to ∼10 nm within 5 h of milling and remain almost unchanged with increasing milling time up to 20 h. Lattice parameter of cubic NiO decreases linearly with increasing milling time, following the Vegard's law of solid-solution alloy. A continuous decrease in lattice parameter of cubic NiFe₂O₄ phase clearly suggests that smaller Ni atoms have occupied some of the vacant oxygen sites of ferrite lattice. Cation distribution both in octahedral and tetrahedral sites changes continuously with milling time and the normal spinel lattice formed at early stage of milling, transforms to inverse spinel lattice in the course of milling. High-resolution transmission electron microscope (HRTEM) micrographs of 11 h milled sample corroborates the findings of X-ray profile analysis.     

Microstructure and optical characterizations of mechanosynthesized nanocrystalline semiconducting ZrTiO4 compound

A ZrO₂–TiO₂ solid solution is obtained by high energy ball milling of equimolar mixture of monoclinic (m) ZrO₂ and anatase (a) TiO₂. Nanocrystalline orthorhombic ZrTiO₄ compound is initiated from the nucleation of TiO₂–ZrO₂ solid solution with isostructural s-TiO₂ (srilankite) base after 30 min of milling. After 12 h of milling, 95 mol% non-stoichiometric ZrTiO₄ phase is formed. Post-annealing of 12 h ball-milled powder mixture at 1073 K for 1 h in open air results in complete formation of stoichiometric ZrTiO₄ compound. Microstructures of all powder mixtures milled for different durations have been characterized by Rietveld's structure and microstructure refinement method using X-ray powder diffraction data. HRTEM images of 12 h milled and annealed samples provide direct evidence of the results obtained from the Rietveld analysis. Optical bandgaps of ball milled and annealed ZrTiO₄ compounds lie within the semiconducting region (~2.0 eV) and increases with increase in milling time.     

Preparation of phase pure and well-crystallized Li4Ti5O12 nanoparticles by precision control of starting mixture and calcining at lowest possible temperatures

In an attempt to obtain spinel Li₄Ti₅O₁₂ with smallest possible grain size and highest possible phase purity via a solid state route, we tried to elevate reactivity of the reactant mixture by mechanical activation and appropriate choice of the starting materials. From the stoichiometric mixture comprising Li₂CO₃ and 150 nm anatase, we needed to heat at 950 °C for 1 h to obtain 81–88% phase purity (PhP) of Li₄Ti₅O₁₂ with its average grain size ca 600 nm. After mechanical activation with a multi-ring mill for 30 min, 850 °C was enough to obtain 85–87% pure 500 nm spinel. From a combination of LiNO₃ and 50 nm anatase, 90–91% phase pure product with its grain size 240 nm was obtained at 750 °C due to fusion of the nitrate and shorter diffusion path. By using CH₃COOLi.2H₂O and 50 nm anatase we obtained 130 nm Li₄Ti₅O₁₂ with its PhP ca 90% by milling the mixture preliminarily calcined at 500 °C for 1 h and heating subsequently at 700 for 1 h.     

Hardness and microstructural variation of Al–Mg–Mn–Sc–Zr alloy

Variations of Vickers hardness were observed in Al–Mg–Mn alloy and Al–Mg–Mn–Sc–Zr alloy at different ageing times, ranging from a peak value of 81.2 HV at 54 ks down to 67.4 HV at 360 ks, below the initial hardness value, 71.8 HV at 0 ks for the case of Al–Mg–Mn–Sc–Zr alloy. Microstructures of samples at each ageing stage were examined carefully by transmission electron microscopes (TEMs) both in two-dimensions and three-dimensions. The presence of different types, densities, and sizes of particles were observed dispersed spherical Al₃Sc_1−xZr_x and also block-shaped Al₃Sc precipitates growing along <1 0 0>_Al with facets {1 0 0} and {1 1 0} of the precipitates. TEM analysis both in two-dimensions and three-dimensions, performed on various samples, confirmed the direct correlation between the hardness and the density of Al₃Sc.     

High lithium ion conductivity glass-ceramics in Li2O–Al2O3–TiO2–P2O5 from nanoscaled glassy powders by mechanical milling

Mechanical milling (MM) has been used to prepare the nanosized Li_1.4Al_0.4Ti_1.6(PO₄)₃ (denoted LATP) glassy powders, which was converted into glass-ceramics through thermal treating at 700–1000 °C. The XRD, TEM, FESEM and ac impedance techniques were used to characterize the products. The results showed that completely amorphous products were prepared by MM for 40 h, and single-phase LiTi₂(PO₄)₃-type structured glass-ceramics were obtained by further heat treatment. The lithium ion conductivity of the glass-ceramics increased with the growth of the crystalline phase and decrease of the grain size. The highest bulk conductivity (σ_b) of 1.09 × 10^− 3 S cm^− 1 with an energy of activation as low as 0.28 eV was obtained at room temperature for the specimen treated at 900 °C for 6 h. The high conductivity, easy fabrication and low cost make the LATP glass-ceramics promising to be used as inorganic solid electrolyte for all-solid-state Li-ion rechargeable batteries.     

Microstructure of multilayer interface in an Al matrix composite reinforced by TiNi fiber

A multilayer interface was formed in the Al matrix composite which was reinforced by 30% volume fraction of TiNi fiber. The composite was fabricated by pressure infiltration process and the interface between the TiNi fiber and Al matrix was investigated by transmission electron microscopy (TEM) and energy dispersive spectroscopy (EDS). When the TiNi fiber was pre-oxidized in the air at 773 K for 1 h, three layers have been found and characterized in the interface: TiNi–B₂ layer near the TiNi fiber, Ti–Al compound layer with Ti and granular TiO₂ near the Al matrix, and Ti–Ni compound layer between TiNi–B₂ and Ti–Al compound layers. The effect of the multilayer interface on the mechanical properties of the composite was also discussed. The result showed that the uniaxial tensile strength of the composite at room temperature was 318 MPa, which was very close to the theoretical calculation value of 326 MPa. Moreover, the composite with good ductility exhibited a typical ductile-fracture pattern.     

Investigations on structural,elastic, thermodynamic and electronic properties of TiN,Ti2N and Ti3N2 under high pressure by first-principles

The lattice parameters, cell volume, elastic constants, bulk modulus, shear modulus, Young's modulus and Poisson's ratio are calculated at zero pressure, and their values are in excellent agreement with the available data, for TiN, Ti₂N and Ti₃N₂. By using the elastic stability criteria, it is shown that the three structures are all stable. The brittle/ductile behaviors are assessed in the pressures from 0 GPa to 50 GPa. Our calculations present that the performances for TiN, Ti₂N and Ti₃N₂ become from brittle to ductile with pressure rise. The Debye temperature rises as pressure increase. With increasing N content, the enhancement of covalent interactions and decline of metallicity lead to the increase of the micro-hardness. Their constant volume heat capacities increase rapidly in the lower temperature, at a given pressure. At higher temperature, the heat capacities are close to the Dulong–Petit limit, and the heat capacities of TiN and Ti₂N are larger than that of c-BN. The thermal expansion coefficients of titanium nitrides are slightly larger than that of c-BN. The band structure and the total Density of States (DOS) are calculated at 0 GPa and 50 GPa. The results show that TiN and Ti₂N present metallic character. Ti₃N₂ present semiconducting character. The band structures have some discrepancies between 0 GPa and 50 GPa. The extent of energy dispersion increases slightly at 50 GPa, which means that the itinerant character of electrons becomes stronger at 50 GPa. The main bonding peaks of TiN, Ti₂N and Ti₃N₂ locate in the range from −10 to 10 eV, which originate from the contribution of valance electron numbers of Ti s, Ti p, Ti d, N s and N p orbits. We can also find that the pressure makes that the total DOS decrease at the Fermi level for Ti₂N. The bonding behavior of N–Ti compounds is a combination of covalent and ionic nature. As N content increases, valence band broadens, valence electron concentration increases, and covalent interactions become stronger. This is reflected in shortening of Ti–N bonds.     

LiMn2−xTixO4 spinel-type compounds (x ≤ 1): Structural,electrical and magnetic properties

LiMn_2−xTi_xO₄ compounds with 0 ≤ x ≤ 1 were prepared by solid state reaction and Pechini technique. Powder X-ray diffraction showed that all samples crystallize with the spinel crystal structure (S.G. Fd3¯m). The cubic unit-cell parameter increases with the Ti content. The influence of the Ti content and cationic distribution on the magnetic properties of the compounds was studied by measuring the temperature and magnetic field dependences of the magnetization: substitution by non-magnetic d⁰ Ti⁴⁺ ions appeared to weaken the magnetic interactions between the manganese ions. The electrical properties of LiMnTiO₄ were studied by AC impedance spectroscopy and DC polarisation measurements, which revealed the electronic character of the conduction process.     

Surface engineering of biomedical metallic materials by plasma-based low-energy ion implantation

Plasma-based low-energy ion implantation, including plasma source ion nitriding/carburizing and plasma source low-energy ion enhanced deposition of thin films, for surface engineering of metallic materials was emerged as low-temperature, low-pressure surface modification technique. Plasma source ion nitriding onto AISI 316L austenitic stainless steel produced a high nitrogen face-centered-cubic phase (γ_N) layer about 10 μm thick at the temperature of 380 °C during 4 h with the high microhardness of HK_0.1 N 22.0 GPa. The microhardness of the nitrided surface from the titanium nitride phase [(Ti, Al, V)N] layer on Ti6Al4V alloy at 750 °C during 4 h achieved up to about HK_0.1 N 15.5 GPa. No pitting corrosion in the Ringer’s solution at 37 °C was detected by electrochemical polarization measurement for the nitrided AISI 316L stainless steel and Ti6Al4V alloy, respectively. Plasma source ion nitriding of the metallic materials provided the engineering surfaces with combined improvement in hardness and corrosion resistance.     

Effect of the solid-state synthesis parameters on the physical and electronic properties of perovskite-type Ba(Fe,Nb)0.5O3 ceramics

Single-phase cubic Ba(Fe,Nb)_0.5O₃ (BFN) powder was synthesized by solid-state reaction at 900, 1000, 1100, 1200 °C for 4 h in air. X-ray diffraction indicated that the BFN oxide mixture calcined at 1200 °C crystallizes to the pure cubic perovskite phase. The crystallite size of the BFN increases slightly with increasing temperature, while the lattice strain progressively decreases. BFN ceramics were produced from this powder by sintering at 1350–1400 °C for 4 h in air. Samples prepared under these conditions achieved up to 97.4% of the theoretical density. The temperature dependence of their dielectric constant and loss tangent, measured at difference frequencies, shows an increase in the dielectric constant with sintering temperature and measurement frequency which is probably due to disorder on the B site ion of the perovskite. The Mössbauer spectra of these sintered BFN ceramics suggests the presence of a superstructure on the B-cation sublattice.     

Ultrasonic cavitation erosion of gas nitrided Ti–6Al–4V alloys

Ultrasonic cavitation erosion experiments were performed on Ti–6Al–4V alloys samples in annealed, nitrided and nitrided and subsequently heat treated state. The protective oxide layer formed as a result of annealing and heat treatment after nitriding is eliminated after less than 30 min cavitation time, while the nitride layer lasts up to 90 min cavitation time. Once the protective layer is removed, the cavitation process develops by grain boundary erosion, leading to the expulsion of grains from the surface. The gas nitrided Ti–6Al–4V alloy, forming a Ti_xN surface layer, proved to be a better solution to improve the cavitation erosion resistance, compared to the annealed and nitrided and heat treated state, respectively. The analysis of the mean depth of erosion rate at 165 min cavitation time showed an improvement of the cavitation erosion resistance of the nitrided samples of up to 77% higher compared to the one of the annealed samples.     

Development of perovskite and phase transition in lead cobalt niobate modified lead zirconate titanate system

Ferroelectric lead zirconate titanate–lead cobalt niobate ceramics with the formula (1 − x)Pb(Zr_1/2Ti_1/2)O₃–xPb(Co_1/3Nb_2/3)O₃ where x = 0.0–0.5 were fabricated using a high temperature solid-state reaction method. The formation process, the structure and homogeneity of the obtained powders have been investigated by X-ray diffraction method as well as the simultaneous thermal analysis of both differential thermal analysis (DTA) and thermogravimetry analysis (TGA). It was observed that for the binary system (1 − x)Pb(Zr_1/2Ti_1/2)O₃–xPb(Co_1/3Nb_2/3)O₃, the change in the calcination temperature is approximately linear with respect to the PCoN content in the range x = 0.0–0.5. In addition, X-ray diffraction indicated a phase transformation from a tetragonal to a pseudo-cubic phase when the fraction of PCoN was increased. The dielectric permittivity is remarkably increased by increasing PCoN concentration. The maximum value of remnant polarization P_r (25.3 μC/cm²) was obtained for the 0.5PZT–0.5PCoN ceramic.     

First principles study of the structure,electronic state and stability of AlnAsm− anions

Structural and electronic properties of semiconductor binary microclusters Al_nAs_m⁻ anions have been investigated using the B3LYP-DFT method in the ranges of n = 1,2 and m = 1–7. Full structural optimization, adiabatic electron affinities calculation and frequency analysis are performed with the basis of 6–311 + G(d). The charged-induced structural changes in these anions have been discussed. The strong As–As bond is also favored over Al–As bonds in the Al_nAs_m⁻ anions in comparison with corresponding neutral cluster. Among different AlAs_m⁻ and Al₂As_m⁻ (m = 1–7) anions, AlAs₄⁻ and Al₂As₃⁻ are most stable.     

Dielectric and ferroelectric properties of 0.8PZT–0.2PCN ceramics under sintering conditions variation

The influences of sintering conditions on electrical properties of the 0.8Pb(Zr_1/2Ti_1/2)O₃–0.2Pb(Co_1/3Nb_2/3)O₃ ceramics have been investigated with sintering temperatures of 1175, 1200, 1225, and 1250 °C and dwell times for 2, 6, and 10 h. The crystal structure of dense specimens showed coexistence between tetragonal, rhombohedral and pseudo cubic phases in all sintering temperatures, while tetragonal-rich phase appeared with increasing dwell times. A maximum dielectric constant was observed at sintering condition of 1200 °C for 2 h, while the transition temperature slightly increased with increasing dwell time. All ceramics also showed diffused phase transition behaviors with a minimum diffusivity at sintering condition of 1200 °C for 2 h. In addition, the polarization–electric field (P–E) hysteresis loops of the ceramic systems also changed significantly with sintering conditions. Interestingly, the ferroelectric parameters; remnant polarization (P_r) and loop squareness (R_sq) tended to increase with increasing sintering temperatures and dwell times.     

Magnetic properties of rare-earth transition metal aluminides R6T4Al43 with Ho6Mo4Al43-type structure

The magnetic properties of 53 aluminium-rich intermetallic compounds R₆T₄Al₄₃ with R=rare-earth elements and T=Ti, V, Nb, Ta, Cr, Mo, W were investigated using polycrystalline samples and a SQUID magnetometer in the temperature range from 2 to 300 K with magnetic flux densities up to 5.5 T. The yttrium and lutetium compounds are Pauli paramagnetic, indicating that the transition metal atoms do not carry magnetic moments. The samarium compounds show van Vleck behavior and antiferromagnetic order with Néel temperatures of less than 12 K. Of these Sm₆Ti₄Al₄₃ becomes metamagnetic. The ytterbium compounds show a mixed or intermediate valent behavior and no magnetic order down to 2 K. All other compounds obey the Curie–Weiss law above 30 K. Their effective magnetic moments correspond to the theoretical moments of the rare-earth ions. They show ferromagnetic or metamagnetic behavior with ordering temperatures all below 20 K. The magnetization curves of most compounds (recorded up to 5.5 T) reach about 50% of the theoretical magnetization already at 0.5 T. The gadolinium compounds are exceptional in that they reach at 0.5 T only about 10% of their theoretical magnetization. The crystal structures of the isotypic compounds Yb₆V₄Al₄₃ and Yb₆Ta₄Al₄₃ were refined from single-crystal X-ray data.     

Microstructural effects on the superionic conductivity of a lithiated glass-ceramic

Three different formulations of 14 Li₂O·9 Al₂O₃·38 TiO₂·39 P₂O₅ composition (LATP) were melted, cast and crystallized. As-cast glass was characterized by differential scanning calorimetry which exhibited a distinct and strong exothermic peak around 680 °C. The peak was attributed to the crystallization of the glass. The crystallized glass (glass-ceramic) was further characterized by X-ray diffraction which showed the existence of Li_1 + xAl_xTi_2 − x(PO₄)₃ (x ⋍ 0.3)as the primary phase mixed with a small concentration of AlPO₄ and an unidentified phase. The scanning electron micrographs revealed the presence of the primary crystalline phase with an average grain size of 1 μm. Electrical characterization by AC impedance spectroscopy revealed grain and grain boundary contributions to the total conductivity. The effect of specimen processing parameters on conductivity is also investigated and discussed.     

Oxidation of ultra-thin Ti films on Mo(100): Soft X-ray photoelectron spectroscopy study

Titanium oxide films grown on Mo(100) have been investigated by low-energy electron diffraction (LEED) and soft X-ray photoelectron spectroscopy (PES). The film was grown by Ti deposition on Mo(100) and subsequent oxidation of the film by 12 L of O₂ exposure at room temperature. As the film was annealed at 700–1000 °C, the film in which the Ti atoms were in a Ti³⁺ oxidation state was formed. As the film was annealed at 1100–1500 °C, the oxidation state of Ti in the film was converted to Ti²⁺. The valence electronic structure of the film was measured under the condition that the emission from the Mo substrate was minimized due to a Cooper minimum of the Mo 4 d photoionization cross sections (hν = 100 eV). It was found that the Ti 3 d band in normal-emission spectra was increased in intensity when the film was annealed at 1100–1500 °C. As the film was annealed at 1300 °C for 10 s and 20 s, the film-covered Mo(100) gave (2 × 2) and (4 × 1) LEED patterns, respectively. The two-dimensional band structure of the (2 × 2) system was investigated by angle-resolved PES, and it was found that the film with a (1 × 1) periodicity with respect to the Mo(100) substrate existed in the (2 × 2) system.     

Synthesis and visible light photocatalysis water splitting property of chromium-doped Bi4Ti3O12

Photocatalysts Bi₄Ti_3 ? xCr_xO₁₂(x = 0.00, 0.06, 0.15, 0.30, 0.40, and 0.50) with perovskite structure were synthesized by sol–gel method and their electronic structures and photocatalytic activities were investigated. The Bi₄Ti_2.6Cr_0.4O₁₂ photocatalyst exhibited the highest performance of H₂ evolution in methanol aqueous solution (58.1 μmol h^? 1 g^? 1) under visible light irradiation (λ > 400 nm) without a co-catalyst, whereas no H₂ evolution is observed for Bi₄Ti₃O₁₂ under the same conditions. The UV–vis spectra indicated that the Bi₄Ti_2.6Cr_0.4O₁₂ had strong photoabsorption in the visible light region. The results of density functional theory (DFT) calculation illuminate that the conduction bands of Bi₄Ti₃O₁₂ are mainly attributable to the Ti 3d + Bi 6p orbitals, and the valence bands are composed of O 2p + Bi 6s hybrid orbitals, while the conduction bands of chromium-doped Bi₄Ti₃O₁₂ are mainly attributable to the Ti 3d + Bi 2p + Cr 3d orbitals, and the O 2p + Cr 3d hybrid obitals are the main contribution to the valence band.     

Microstructure evolution process of Ferro-Aluminum based sandwich composite for electromagnetic shielding

In this paper, sandwich composite (SWC) with Fe–Al soft magnetic alloy sandwiched between pure iron substrates was proposed and fabricated by hot pressing and diffusion treatment. The microstructure evolution process of the composite was investigated. Fe/Fe₂Al₅/Fe diffusion couple was obtained at 700 °C and subsequently kept at 900 °C for further isothermal diffusion. During the diffusion reactive process, we confirmed that major FeAl₂ and minor Fe₄Al₁₃ were produced when Fe₂Al₅ dissolved. After 10 h of diffusion treatment, FeAl and α-Fe(Al) were the only two intermetallic phases left. Except FeAl₂, the thickness of each intermetallic layer held good parabolic relationship with the diffusion annealing time.     

Microwave synthesis of nitrogen doped Ti4O7 for photocatalytic applications

The nitrogen (N) doped Ti₄O₇ photocatalyst was prepared from urea as a nitrogen source by a microwave method. The resulting photocatalyst was characterized by X-ray diffraction (XRD), Field Emission Scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), UV–visible diffuse reflectance spectroscopy (UV–Vis DRS) and UV–vis spectroscopy (UV–Vis). 0.1 M N doped Ti₄O₇ photocatalyst exhibited methylene blue decomposition efficiency of 100% which was prepared by microwave treatment for above 30 min. Rate constant was found to be 0.028910 min⁻¹ in the first order kinetic.