Passively Mode-Locked Er-Doped Fiber Laser Based on Sb2S3-PVA Saturable Absorber

In this paper, antimony trisulfide (Sb₂S₃) was successfully prepared with the liquid phase exfoliation method and embedded into polyvinyl alcohol (PVA) as a saturable absorber (SA) in a passively mode-locked Er-doped fiber laser for the first time. Based on Sb₂S₃-PVA SA with a modulation depth of 4.0% and a saturable intensity of 1.545 GW/cm², a maximum average output power of 3.04 mW and maximum peak power of 325.6 W for the stable mode-locked pulses was achieved with slope a efficiency of 0.87% and maximum single pulse energy of 0.81 nJ at a repetition rate of 3.47 MHz under a pump power of 369 mW. A minimum pulse width value of 2.4 ps with a variation range less than 0.1 ps, and a maximum signal to noise ratio (SNR) of 54.3 dB indicated reliable stability of mode-locking, revealing promising potentials of Sb₂S₃ as a saturable absorber in ultrafast all-fiber lasers.     

Tunable and Passively Mode-Locking Nd0.01:Gd0.89La0.1NbO4 Picosecond Laser

A high-quality Nd_0.01:Gd_0.89La_0.1NbO₄ (Nd:GLNO) crystal is grown by the Czochralski method, demonstrating wide absorption and fluorescence spectra and advantage for producing ultrafast laser pulses. In this paper, the tunable and passively mode-locking Nd:GLNO lasers are characterized for the first time. The tuning coverage is 34.87 nm ranging from 1058.05 to 1092.92 nm with a maximum output power of 4.6 W at 1065.29 nm. A stable continuous-wave (CW) passively mode-locking Nd:GLNO laser is achieved at 1065.26 nm, delivering a pulse width of 9.1 ps and a maximum CW mode-locking output power of 0.27 W.     

WS2 Nanowires as a High‐Performance Anode for Sodium‐Ion Batteries

We report the synthesis and anode application for sodium‐ion batteries (SIBs) of WS₂ nanowires (WS₂ NWs). WS₂ NWs with very thin diameter of ≈25 nm and expanded interlayer spacing of 0.83 nm were prepared by using a facile solvothermal method followed by a heat treatment. The as‐prepared WS₂ NWs were evaluated as anode materials of SIBs in two potential windows of 0.01–2.5 V and 0.5–3 V. WS₂ NWs displayed a remarkable capacity (605.3 mA h g^?1 at 100 mA g^?1) but with irreversible conversion reaction in the potential window of 0.01–2.5 V. In comparison, WS₂ NWs showed a reversible intercalation mechanism in the potential window of 0.5–3 V, in which the nanowire‐framework is well maintained. In the latter case, the interlayers of WS₂ are gradually expanded and exfoliated during repeated charge–discharge cycling. This not only provides more active sites and open channels for the intercalation of Na⁺ but also facilitates the electronic and ionic diffusion. Therefore, WS₂ NWs exhibited an ultra‐long cycle life with high capacity and rate capability in the potential window of 0.5–3 V. This study shows that WS₂ NWs are promising as the anode materials of room‐temperature SIBs.     

Synthesis and laser application of the dithiolene nickel complex compounds

A series of dithiolene nickel complex compounds with a general formula (RCSCSR′)₂Ni that have an intense absorption band in near-IR region were successfully synthesized and the maximum IR absorption wavelengths of these dyes vary from 875 to 1495 nm in different solvents. Their characteristics of Q-switching and mode-locking for different lasers were investigated. Q-switched 1064 and 1079 nm laser with a polymer film or organic solution work satisfactorily and the pulse widths are 4–10 ns. The dyes in a variety of solutions show excellent properties in mode-locking the 1079 nm laser, particularly in mode-locking the 1340 nm laser. The pulse widths are 90–120 ps. The experimental results show that the choice of different ring substitutes and solvents will greatly influence the corresponding dye laser properties. It is also implied that BDN16 and BDN17 as the mode-locking dyes for the 1500 nm laser are satisfactory.     

Preparation of WS2 nanocomposites via mussel-inspired chemistry and their enhanced dispersion stability and tribological performance in polyalkylene glycol

A novel biomimetic surface modification method utilizing mussel-inspired chemistry was used to prepare tungsten disulfide (WS₂) nanocomposites, which enhanced the dispersion stability and tribological performance of WS₂ in polyalkylene glycol (PAG). Herein, WS₂-polydopamine-methoxypolyethylene glycol amine (WS₂-PDA-MPGA) was first synthesized via mussel-inspired chemistry and used as a lubricant additive in PAG. After modification, the dispersion stability of WS₂ nanosheets in PAG was obviously improved. Moreover, the tribological performance of WS₂-PDA-MPGA in PAG at high temperature was evaluated by the oscillating reciprocating tribometer. Compared to pure PAG, the lubricant composition containing WS₂-PDA-MPGA exhibited excellent performance in friction reduction and anti-wear properties at high temperature. The optimal tribological performance could be obtained when the percentage of additives was 0.9?wt%. The tribological results indicate that WS₂-PDA-MPGA, with its good dispersion stability, has better friction reduction and anti-wear properties than does WS₂ in PAG base oil. The chemical composition analysis of the wear surface indicated that a stable protective film had been formed by physical adsorption and tribo-chemical reactions. Therefore, the surface modification strategy is an effective way to improve the dispersion stability of WS₂ in PAG, which can be expanded application of WS₂ in the tribological field.     

水热合成二硫化钨/石墨烯复合材料及其氧还原性能

以六氯化钨、硫代乙酰胺、氧化石墨烯为原料,采用一步水热法合成了二维的二硫化钨/石墨烯(WS₂/RGO)复合材料。水热合成的WS₂/RGO具有薄层的二维结构,且由于石墨烯的存在,WS₂以较少的层数形成薄片状生长在石墨烯的表面。尝试将这种非Pt类材料用于电催化氧化原反应,测试结果表明,WS₂在碱性条件下氧还原活性非常低,但是复合RGO形成WS₂/RGO复合材料后,电催化氧化原性能有了极大的提高,其起始电位为-0.17 V(vs SCE),转移电子数为3.7,极限电流密度为2.5 mA·cm^-2,同时其具有较好的抗甲醇性能和循环稳定性。这是因为WS₂/RGO复合材料的二维结构具有更高的电子传输速率,同时硫化钨和石墨烯可以发挥协同催化作用。这种新型的二硫化钨/石墨烯(WS₂/RGO)复合材料作为非贵金属催化剂表现出良好的氧还原性能,在燃料电池上具有较好的应用前景。     

Highly enhanced thermoelectric performance of WS2 nanosheets upon embedding PEDOT:PSS

Two‐dimensional (2D) WS₂ nanosheets (NSs) as a promising thermoelectric (TE) material have gained great concern recently. The low electrical conductivity significantly limits its further development. Herein, we reported an effective method to enhance the TE performance of WS₂ NSs by combining poly(3,4‐ethylenedioxythiophene):poly(4‐styrenesulfonate) (PEDOT:PSS). The restacked WS₂ NSs thin film with 1T phase structure obtained by a common chemical lithium intercalation show a high Seebeck coefficient of 98 μV K^?1 and a poor electrical conductivity of 12.5 S cm^?1. The introduction of PEDOT:PSS with different contents obviously improve the electrical conductivity of WS₂ NSs thin films. Although a declining Seebeck coefficient was observed, an optimized TE power factor of 45.2 μW m^?1 k^?1 was achieved for WS₂/PEDOT:PSS composite thin film. Moreover, the as‐prepared WS₂/PEDOT:PSS thin film can be easily peeled off and transferred to other substrate leading to a more promising application. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 997–1004     

水热合成二硫化钨/石墨烯复合材料及其氧还原性能

以六氯化钨、硫代乙酰胺、氧化石墨烯为原料,采用一步水热法合成了二维的二硫化钨/石墨烯(WS_2/RGO)复合材料。水热合成的WS_2/RGO具有薄层的二维结构,且由于石墨烯的存在,WS_2以较少的层数形成薄片状生长在石墨烯的表面。尝试将这种非Pt类材料用于电催化氧化原反应,测试结果表明,WS_2在碱性条件下氧还原活性非常低,但是复合RGO形成WS_2/RGO复合材料后,电催化氧化原性能有了极大的提高,其起始电位为-0.17 V(vs SCE),转移电子数为3.7,极限电流密度为2.5 m A·cm-2,同时其具有较好的抗甲醇性能和循环稳定性。这是因为WS_2/RGO复合材料的二维结构具有更高的电子传输速率,同时硫化钨和石墨烯可以发挥协同催化作用。这种新型的二硫化钨/石墨烯(WS_2/RGO)复合材料作为非贵金属催化剂表现出良好的氧还原性能,在燃料电池上具有较好的应用前景。     

Analysis of approximations and errors in equations of motion method calculations

We analyze a number of fundamental questions associated with the use of a finite one-particle orbital basis in equations of motion (EOM) method calculations of excitation energies etc., of atomic and molecular systems. This approximation yields an approximate n_e-electron ground state and say, N excited states, while there are (N + 1)² different possible basis operators for EOM calculations. We show that sets of at most 2N basis operators can contribute to the EOM calculations. Any set of 2N basis operators, satisfying certain conditions, provides the exact EOM energies which are equivalent to complete configuration interaction results within the same orbital basis. We investigate the use of particle-particle shifting operators which are not employed in EOM calculations in model calculations on He with operator bases smaller than the complete 2V to consider the convergence of the expansion. The dependence of EOM calculations on the quality of the approximate ground state wavefunction is studied through calculations for Be where additional support is provided for the frequent need for multiconfigurational zeroth order reference functions (as corrected perturbatively). Excited state EOM wavefunctions from EOM calculations are shown to not necessarily be orthogonal to either the exact or approximate ground state wavefunction, suggesting implications in the use of EOM methods to evaluate excited state properties. The He and Be examples and a simple two-level problem are also utilized to illustrate questions concerning the use of the EOM equations to obtain an iteratively improved ground state wavefunction.     

Construction of 2D-2D TiO2 nanosheet/layered WS2 heterojunctions with enhanced visible-light-responsive photocatalytic activity

Constructing nanocomposites that combine the advantages of composite materials, nanomaterials, and interfaces has been regarded as an important strategy to improve the photocatalytic activity of TiO₂. In this study, 2D-2D TiO₂ nanosheet/layered WS₂ (TNS/WS₂) heterojunctions were prepared via a hydrothermal method. The structure and morphology of the photocatalysts were systematically characterized. Layered WS₂ (～4 layers) was wrapped on the surface of TiO₂ nanosheets with a plate-to-plate stacked structure and connected with each other by W=O bonds. The as-prepared TNS/WS₂ heterojunctions showed higher photocatalytic activity for the degradation of RhB under visible-light irradiation, than pristine TiO₂ nanosheets and layered WS₂. The improvement of photocatalytic activity was primarily attributed to enhanced charge separation efficiency, which originated from the perfect 2D-2D nanointerfaces and intimate interfacial contacts between TiO₂ nanosheets and layered WS₂. Based on experimental results, a double-transfer photocatalytic mechanism for the TNS/WS₂ heterojunctions was proposed and discussed. This work provides new insights for synthesizing highly efficient and environmentally stable photocatalysts by engineering the surface heterojunctions.     

WS<Subscript>2</Subscript> grafted on silicon and nano-silicon particles etched: a high-performance electrocatalyst for hydrogen evolution reaction

Most of research has been carried out for the development of electrocatalysts for hydrogen evolution reaction (HER), which are high activity and low cost. In this study, a practical, usable, highly active, cheap, and none noble metal catalyst was developed for HER. To this end, tungsten disulfide supported on silicon (WS₂/Si) and on silicon nanoparticles (WS₂/nano-Si) were prepared. To increase the catalytic activity of WS₂/nano-Si, chemical etching was used to prepare WS₂/nano-Si etched. The synthesized electrocatalysts were characterized using Fortier transform infrared spectroscopy, field emission scanning electron microscopy, X-ray photoelectron spectroscopy, and X-ray diffraction methods. To evaluate the electrochemical attributes of WS₂/Si and WS₂/n-Si before and after chemical etching, electrochemical impedance spectroscopy, linear sweep, and cyclic voltammetry were used. The electrochemical measurements indicated an intense activity of the WS₂/nano-Si/etched, through a high density of the current and low overpotential for HER, with a small overpotential of 0.14 V, Tafel slopes as small as 45 mV dec^?1, and large cathodic currents. These results show that through etching process of silicon in HF the quantities of the active sites have been changed and increased considerably.     

Significance of epoxy network properties for the toughening effect of flaky and fullerene‐like WS2 nanoparticles

This work deals with the toughening effect of flaky WS₂ and fullerene‐like WS₂ (IF‐WS₂) nanoparticles on epoxy with varying network properties. Reducing the amount of curing agent resulted in decreased crosslink density as measured by dynamic‐mechanic analysis and double‐quantum nuclear magnetic resonance spectroscopy. Although that lead to moderate changes in the epoxy's tensile properties, its fracture toughness dropped drastically, probably due to an increased defect fraction. IF‐WS₂ could be dispersed significantly more effectively within epoxy resin than flaky WS₂, possibly due to its spherical shape, but caused less toughening. IF‐WS₂ tended to debond from the epoxy, while flaky WS₂ introduced more secondary cracks. Both increased the fracture toughness of the (brittle) substoichiometric, but not that of the (tough) stoichiometric epoxy, possibly due to their interaction with molecular defects. Irrespective of which mechanism resulted in the toughening effect, its effectiveness depended strongly on the epoxy matrix. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1738–1747     

Electrochemical behavior of horseradish peroxidase on WS2 nanosheet‐modified electrode and electrocatalytic investigation

In this paper, a WS₂ nanosheet was modified on the surface of a carbon ionic liquid electrode (CILE), and horseradish peroxidase (HRP) was further fixed on the electrode with a Nafion film. Direct electrochemistry and bioelectrocatalysis of HRP incorporated on the modified electrode were investigated in detail. On Nafion/HRP/WS₂/CILE, a pair of well‐defined quasi‐reversible redox peaks appeared on the cyclic voltammogram, indicating that the presence of the WS₂ nanosheet on the electrode surface could provide a specific interface with large surface area for HRP and its direct electron transfer rate was greatly enhanced. The formal potential (E⁰) obtained was –0.179 V, which was the typical feature of heme Fe(III)/Fe(II) in HRP. The electron transfer coefficient (α) and the heterogeneous electron transfer rate constant (k_s) of HRP were calculated as 0.44 and 1.01 s^–1, respectively. This HRP‐modified electrode showed excellent electrocatalytic activity for the reduction of trichloroacetic acid and NaNO₂ with a wide linear range and low detection limit. Real samples were detected by this proposed method, indicating the successful fabrication of a new third‐generation electrochemical enzyme sensor utilizing the WS₂ nanosheet.     

Synthesis of tungsten disulfide (WS2) nanoflakes for lithium ion battery application

A novel method (a rheological phase reaction) was used to synthesize WS₂ nanoflakes by adding oxalic acid as a reducing reagent. High resolution electron microscopy observations revealed that the as-prepared WS₂ nanoflakes had started to curve and that WS₂ nanotubes were partly formed. The lithium intercalation/deintercalation behavior of as-prepared WS₂ electrode was also investigated. It was found that the WS₂ nanoflake electrode exhibited higher specific capacity with very good cycling stability compared to WS₂ nanotube or nanoparticle electrodes. The reasons for the improved electrochemical performance of the nanoflake electrodes are also discussed.     

Influence of inorganic fullerene‐like WS2 nanoparticles on the thermal behavior of isotactic polypropylene

A new family of thermoplastic nanocomposites based on isotactic polypropylene (iPP) and inorganic fullerene‐like tungsten disulfide (IF‐WS₂) has been successfully prepared. A very efficient dispersion of IF‐WS₂ material was obtained by mixing in the melted polymer without using modifiers or surfactants. The addition of IF‐WS₂ nanoparticles induces a remarkable enhancement of the thermal stability of iPP, as well as an increase in the crystallization rate of the matrix when compared with pure iPP. The nucleating efficiency of IF‐WS₂ solid lubricant nanoparticles on the α‐phase of iPP reaches very high values (60–70%), the highest values observed hitherto for polypropylene nanocomposites. The incorporation of IF‐WS₂ has also been observed to increase the size and stability of the crystals formed. The melting behavior of the nanocomposites indicates the formation of more perfect crystals as determined by differential scanning calorimetry and time‐resolved synchrotron X‐ray scattering experiments. The new nanocomposites show an increase in the storage modulus with respect to pure iPP measured by dynamic mechanical analysis. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2309–2321, 2007     

WS2纳米颗粒的合成及摩擦学性能研究

将自制的WO₃纳米颗粒前驱体与S粉混合,在自制的反应装置氢气氛中,于550～750 ℃下煅烧得到二硫化钨纳米颗粒,反应中用H₂代替H₂S以减少对周围环境的污染。该合成路线简单且产物纯度高。用XRD、SEM、TEM和HRTEM对二硫化钨纳米结构进行了表征和分析,并将WS₂纳米颗粒作为添加剂添加到N40基础油中,在MS-T3000摩擦磨损仪测试其摩擦学性能。结果显示:制备的二硫化钨颗粒平均粒径在50 nm以内,其形状为球形或类球形。WS₂纳米颗粒作为普通润滑油的纳米级固体添加剂表现出了较优异的摩擦学性能。     

Investigation of photocatalytic chlorpyrifos degradation by a new silica mesoporous material immobilized by WS2 and Fe3O4 nanoparticles: Application of response surface methodology

In the present research, Fe₃O₄ and WS₂ nanoparticles immobilized on or in KIT-6 (KIT: Korea Institute of Science and Technology) pores (KIT-6/WS₂-Fe₃O₄) were synthesized and studied as a photocatalyst for degradation of representative chlorpyrifos as an organophosphorus pesticide. In addition, the KIT-6/WS₂-Fe₃O₄ photocatalyst was characterized by different methods such as TEM, FESEM-EDS-Mapping, XRD, and N₂ adsorption/desorption surface area, in order to understand their morphology, structural, and physical properties. The photocatalytic performance of this photocatalyst was investigated for degradation of chlorpyrifos by visible light irritation. The effects of variables such as chlorpyrifos concentration, KIT-6/WS₂-Fe₃O₄ nanocatalyst amount, pH, and irradiation time on chlorpyrifos degradation efficiency was studied by central composite design with response surface methodology. The optimum conditions for CP degradation were obtained by 50 mg KIT-6/WS₂-Fe₃O₄ nanocatalyst, and 7.2 ppm chlorpyrifos solution with pH = 6, at 52 min. The pseudo-first-order model with rate constants equal to 0.069 min⁻¹ as best choice efficiency described the chlorpyrifos degradation process according to Langmuir-Hinshelwood kinetic.     

Metal–Organic Frameworks Constructed from Versatile [WS4Cux]x−2 Units: Micropores in Highly Interpenetrated Systems

Five metal–organic frameworks (MOFs) formed by [WS₄Cu_x]^x?2 secondary building units (SBUs) and multi‐pyridyl ligands are presented. The [WS₄Cu_x]^x?2 SBUs function as network vertexes showing various geometries and connectivities. Compound 1 contains one‐dimensional channels formed in fourfold interpenetrating diamondoid networks with a hexanuclear [WS₄Cu₅]³⁺ unit as SBU, which shows square‐pyramidal geometry and acts as a tetrahedral node. Compound 2 contains brick‐wall‐like layer also with a hexanuclear [WS₄Cu₅]³⁺ unit as SBU. The [WS₄Cu₅]³⁺ unit in 2 is a new type of [WS₄Cu_x]^x?2 cluster unit in which the five Cu⁺ ions are in one plane with the W atom, forming a planar unit. Compound 3 shows a nanotubular structure with a pentanuclear [WS₄Cu₄]²⁺ unit as SBU, which is saddle‐shaped and acts as a tetrahedral node. Compound 4 contains large cages formed between two interpenetrated (10,3)‐a networks also with a pentanuclear [WS₄Cu₄]²⁺ unit acting as a triangular node. The [WS₄Cu₄]²⁺ unit in 4 is isomeric to that in 3 and first observed in a MOF. Compound 5 contains zigzag chains with a tetrahedral [WS₄Cu₃]⁺ unit as SBU, which acts as a V‐shaped connector. The influence of synthesis conditions including temperature, ligand, anions of Cu^I salts, and the ratio of [NH₄]₂WS₄ to Cu^I salt on the formation of these [WS₄Cu_x]^x?2‐based MOFs were also studied. Porous MOF 3 is stable upon removal and exchange of the solvent guests, and when accommodating different solvent molecules, it exhibits specific colors depending on the polarity of incorporated solvent, that is, it shows a rare solvatochromic effect and has interesting prospects in sensing applications.     

球磨-溶剂热诱导法合成WS2纳米棒及其摩擦性能

采用行星式高能球磨机，将WS₂与S粉末混合球磨，得到纳米片状结构的前驱体，然后添加分散剂聚乙二醇(PEG)用溶剂热诱导的方法使纳米片状前驱体发生结构转变，制备了棒状结构的WS₂纳米材料。用XRD、SEM、TEM等方法对WS₂纳米棒进行了形貌和结构表征，并对其作为润滑油添加剂的摩擦性能进行了初步的研究。     

Übergangsmetallchalkogenverbindungen. Über CuNH4WS4 und Cu2WS4 und andere Übergangsmetallchalkogenmetallate

Transition metal chalkogen compounds. On CuNH₄WS₄, Cu₂WS₄ and other transition metal chalkogenometallates The preparation, vibrational and electronic spectra of CuNH₄WS₄, Cu₂WS₄ and other transition metal compounds, which could not be isolated in a pure form, are reported. The X-ray data of CuNH₄WS₄ are given.