Determination of boron in glass by the nuclear track technique

Summary Determination of Boron in Glass by the Nuclear Track Technique The nuclear track technique using the¹⁰B(n)⁷Li reaction, has been applied to determine boron in concentration ranges (1.59 to 7.75%) ordinarily considered high for nuclear determinations. Factors limiting the overall precision of the method and restricting the linear dependence of track density on boron concentration are examined. Boron alpha track densities are used to construct planar profiles of boron distribution within the surface region of bulk glass and CVD films. Calibration curves for quantitative lateral profiling of surfaces are constructed and show the selective corrosion of borosilicate glass surface resulting in boron depletion.     

Gas distribution in the layer of irregular ring nozzle

Results of experiments on evaluation of velocity fields in the apparatus of diameter 98 mm loaded with irregular ring nozzle of different type so that the ratio of the diameter of the apparatus to the diameter of the packing D/d = 10 are analyzed in the article. The significant influence of the walls limiting the layer of packing on the uniformity of distribution of the velocity field in the cross-section of the apparatus with packing is shown. Raschig rings, rings of MS type and rings of N1 type of dimensions 10 × 10 × 0.9 mm made of metal were used as packing. The data obtained on Raschig rings were compared with published data.     

An effect of sprinkling density on a value of active surface of irregular heat and mass transfer packing

The results of analysis of an influence of a sprinkling density in the packed columns were reported on a value of an active surface of irregular ring nozzles such as Raschig and Pall rings. Sizes of Raschig rings were 15, 25 and 50 mm; Pall rings, 50 mm. Values of fluid load was 10, 20, 30, 40 and 50 m³ m⁻² h⁻¹). The results of the analysis were presented in graph form.     

PVC膜修饰电极上零电流示波电位滴定法测定硼的研究

以氯化十六烷基吡啶（ＣＰＣ）和氟硼酸钠形成的离子缔合物为活性物质，制成ＰＶＣ膜涂层石墨电极，提出了一个快速测定硼的零电流示波电位滴定法。以ＣＰＣ为滴定剂，用ＰＶＣ膜电极为指示电极，甘汞电极为参比电极，利用阴极射线示波器荧光屏上荧光点的突然位移来指示ＣＰＣ滴定硼的终点，具有灵敏、准确、快速等特点，用该法测定玻璃中的硼，结果良好。     

Precise determination of boron by titration with a multiparametric curve-fitting procedure for data evaluation

A precise method is described for the determination of boric acid and boron in metal borides by potentiometric titration of the mannitol/boric acid complex with a strong alkali. Titration data are evaluated by a multiparametric curve-fitting procedure on the basis of model functions for this type of titration. The initial boric acid concentration, or parameters like the conditional acidity constant and the association number of the mannitol/boric acid complex can be determined. For a sample of titanium boride, the standard deviation was 0.15% on a boron content of 29.18%.     

Determination of boron concentration in borosilicate glass,boron carbide and graphite samples by conventional wet-chemical and nuclear analytical methods

Boron is an important element in nuclear technology. A comparative study was carried out for the determination of boron in borosilicate glass, boron carbide and graphite samples by wet-chemical and nuclear analytical methods. Wet chemical methods namely titrimetry, Inductively Coupled Plasma Mass Spectrometry and ICP Optical Emission Spectrometry and nuclear analytical methods namely Particle Induced Gamma-Ray Emission and Nuclear Reaction Analysis were used. Boron concentrations were in trace (mg kg^?1) level in graphite and percentage level in borosilicate glass and boron carbide.     

Models of turbulent viscosity and mixing in channels and packed flow-through mixers

The use of packed flow-through mixers for intense mixing of liquid media and of liquids with a finely dispersed phase is considered. Ways to determine the mixing and turbulent exchange coefficients for evaluating the mixing efficiency in channels and in packed flow-through mixers are presented. The results are consistent with the experimental data on turbulent viscosity in pipes. An expression is obtained for calculating the turbulent viscosity coefficient in a packing bed. Comparative characteristics of mixers with Raschig rings and Inzhekhim packing are presented. The calculated values of the Peclet number for various packings in relation to the Reynolds number are given.     

Determination of boron in glass by neutron transmission method

Neutron transmission method has been used for the determination of boron in borosilicate glasses. The method is sensitive and rapid to control the spatial homogeneities of glass-product in the melting furnace.Dedicated to Academician J. Csikai on his 60th birthday.This work was supported by the National Foundation for Research (Contact No. 259).     

Potentiometric determination of boron in silicon with an ion-selective electrode

A potentiometric method is proposed for the determination or boron in silicon, based on dissolution of silicon by treatment with hydrofluoric acid and ammonium fluoride in the presence of hydrogen peroxide, and conversion of boron to fluoroborate ion. The fluoroborate activity is measured with the Orion fluoroborate-selective electrode. Some important points, such as the effect of various interfering ions and the hydrolysis of fluoroborate ion, are described in detail. The method is applied to the determination of boron in silicon containing at least 10 p.p.m. of boron, with a relative standard deviation of ±4%.     

自动电位滴定快速测定84消毒液中的有效氯含量

During the outbreak of novel coronavirus pneumonia, 84 Disinfectant has been widely used. It is very important to determine the available chlorine content in 84 Disinfectant. A new method to rapidly determine the available chlorine content in 84 Disinfectant by automatic potentiometric titration was established. Statistically, there is no significant difference in results between automatic potentiometric titration and manual titration. Combined the principles of analytical chemistry and the application to the determination of anti-epidemic material, this experiment has theoretical and practical significance, and can be used as an experiment in analytical chemistry laboratory for sophomore students.     

Active surface of elements of irregular heat and mass transfer packing

Mechanisms of formation of the active surface of irregular heat and mass transfer packing are analyzed. Widely spread packing like Raschig, Pall rings, circular packing GIAP-NZ as well as Intalox saddles are considered. Results of comparison of the efficiency of packing GIAP-NZ of different size and at different loads are presented. At comparing the design of packing the concept of the coefficient of the utilization efficiency of the packing volume is used.     

Internal modification of poly(dimethylsiloxane) microchannels with a borosilicate glass coating

We report on an original technique for the in situ coating of poly(dimethylsiloxane) (PDMS) microchannels with borosilicate glass, starting from an active nonaqueous and alkali-free precursor solution. By chemical reaction of this active solution inside the microchannel and subsequent thermal annealing, a protective and chemically inert glass borosilicate coating is bonded to the PDMS. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy and nuclear magnetic resonance spectroscopy of the active solution show that it is composed of a silicon oxide network with boron connectivity. Thermal gravimetric analysis demonstrates the absence of organic content when curing is done above 150 degrees C. The borosilicate nature of the glass coating covalently bonded to the PDMS is demonstrated using ATR-FTIR spectroscopy and X-ray photoelectron spectroscopy. Atomic force microscopy and scanning electron microscopy show a smooth and crack-free coating. The latter is used as an efficient protective barrier against diffusion in PDMS of fluorescent rhodamine B dye that is dissolved either in water or in toluene. Moreover, the coating prevents swelling and consequent structural damage of the PDMS when the latter is exposed to harsh chemicals such as toluene.     

Establishing the difference between colloidal borosilicate and boron-modified colloidal silica via chelation of boron with catechol and dl-tartaric acid

Colloidal borosilicate and boron-modified colloidal silica sols were studied by ¹¹B NMR. Formation of B–O–Si chemical bonds is established in both materials. It is shown that boron present in colloidal borosilicate is stable towards the action of complexing agents catechol and tartaric acid. In contrast, the boron in boron-modified silica is readily complexed by these agents. The results presented herein demonstrate that B–O–Si bonds are homogeneously distributed throughout the colloidal borosilicate disperse phase, while in boron-modified colloidal silica they are concentrated at the surface of colloidal silica particles.     

A new concept for the noncovalent binding of a ruthenium-based olefin metathesis catalyst to polymeric phases: preparation of a catalyst on Raschig rings

A new concept for noncovalent immobilization of a ruthenium olefin metathesis catalyst is presented. The 2-isopropoxybenzylidene ligand of a Hoveyda-Grubbs carbene is further modified by an additional amino group (7) and immobilization is achieved by treatment with sulfonated polystyrene forming the corresponding ammonium salt. In this novel strategy for the immobilization of ruthenium-based metathesis catalysts, the amino group plays a two-fold role, being first an active anchor for immobilization and second, after protonation, activating the catalysts (electron donating to electron withdrawing activity switch). The polymeric support was prepared by precipitation polymerization which led to small bead sizes (0.2-2 microm) and large surface areas. Compared to commercial resins this tailor-made phase showed superior properties in immobilization of complex 7. This concept of immobilization was applied to glass-polymer composite megaporous Raschig rings. Ru catalyst 7 on Raschig rings was used under batch conditions in various metathesis reactions, including ring-closing (RCM), cross- (CM) and enyne metathesis, to give products of high chemical purity with very low ruthenium contamination levels (21-102 ppm). The same ring can be used for up to 6 cycles of metathesis.     

Determination of boron in glass by alpha-spectrometry

Alpha-spectrometric method has been used for the determination of boron in borosilicate glasses. For irradiation thermal neutrons with a flux of about 10⁵ n·cm^–2·s^–1, produced in a paraffin moderator surrounding a deuteron target of a small neutron generator, were used. Alpha-particles from the reaction¹⁰B(n, ) were detected by a Si solid state detector with a resolution of about 50 keV. The sensitivity of the method is 0.05 wt % boron in glass samples.This work was supported by the Hungarian Research Foundation (Contract No. 1734/91.).     

Determination of boron in borosilicate glasses by neutron capture prompt gamma-ray activation analysis

Major levels of boron in borosilicate glasses have been determined nondestructively by neutron activation analysis. In contrast to chemical methods for determining boron as a major component, the described nuclear method has few interferences and does not require chemical separation of boron prior to its quantitation. The effects of neutron self-shielding by boron (1 to 8% by weight) are examined, minimized by dilution of powdered samples with high purity graphite, and circumvented by comparative analyses. Results of the analysis of a series of glasses with increasing boron composition are 1.150±.005% and 7.766±.035% for the low and high members of the series. Accuracy of these results depends upon comparative analyses with the certified Standard Reference Material, SRM 93a (3.89±0.02% B). Once analyzed, the glasses are useful as secondary standards for alpha track counting, and also ion and electron microprobe analyses of glasses.     

Synthesis and characterisation of functionalized borosilicate nanoparticles for boron neutron capture therapy applications

Boron Neutron Capture Therapy (BNCT) is a promising therapy for the cure of diffuse tumors. The successful clinical application of BNCT requires finding new boron-based compounds suitable for an efficient ¹⁰B delivery to the cancerous tissues. The purpose of this work is to synthesize borosilicate nanoparticles by a sol?Cgel recipe, and to functionalize them with folic acid in order to promote their capture by the tumor cells. Whereas sol?Cgel is a promising technique for the synthesis of nanoparticles, in case of borosilicate systems this approach is affected by significant boron loss during preparation. Here we show that functionalization of borosilicate nanoparticles with folic acid can reduce the boron loss. Moreover, preliminary biocompatibility tests indicate that functionalization strongly changes the reactivity of NPs towards blood cells, so favouring the potential use of these materials for clinical applications.     

Analysis of Borosilicate Catalysts by Inductively Coupled Plasma Atomic Emission Spectroscopy

Abstract

A method was developed for the analysis of borosilicate catalysts. Samples were prepared by fusion technique with potassium hydroxide and analyzed by inductively coupled plasma atomic emission spectroscopy (ICP-AES). The method was applied to a borosilicate NIST SRM 93 which was analyzed for major and minor elements (aluminum, sodium, silicon and boron). Despite the presence of relatively high concentration of the potassium, no matrix interferences were observed. This method provides precision and accuracy better than ±4% and ±6%, respectively.     

Determination of boron and nitrogen in boron nitride

Improved techniques are described for the determination of boron and nitrogen in pure boron nitride. Controlled fusion of boron nitride with sodium carbonate in a muffle furnace is followed by a potentiometric titration of the boric acid. A special quartz vessel is described for the determination of nitrogen. The boron nitride is fused with sodium hydroxide and the resulting ammonia is swept into a receiver and titrated with standard hydrochloric acid. Boron and nitrogen values with their standard deviation are given for a typical pure boron nitride.     

Flow injection spectrophotometric determination of boron in ceramic materials

A flow injection spectrophotometric method for the determination of boron in ceramic materials is described. The method is based on spectrophotometric measurement of the decrease in the pH produced by the reaction between boric acid and mannitol in the presence of an acid-base indicator. A bichannel FI (flow injection) manifold in which the sample solutions were injected into deionized water (at pH 5.4) and the stream was later merged with the reagent stream (a mannitol solution containing 1x10(-4) mol l(-1) bromocresol green at pH 5.4), was used. Transient signals were monitored at 616 nm. A theoretical model which describes the dependence between the absorbance values and boric acid concentration is presented. The model predicts a non linear dependence between the absorbance or increment in absorbance and the boric acid concentration. In contrast, the model predicts a linear dependence between the inverse of the absorbance values and the boric acid concentration. The calibration graphs (1/A vs mug ml(-1) B(2)O(3)) were linear over the range 1-30 mug ml(-1) of B(2)O(3). The relative standard deviations were 0.7 and 0.4% for 4 and 8 mug ml(-1) of B(2)O(3), respectively. The limit of detection was 0.02 mug ml(-1) of B(2)O(3) (3sigma criterium). The method was used to determine boron in nine ceramic materials with very different nominal boron compositions. The results were compared with those obtained using a potentiometric titration method as reference method. No significant differences (at 95% probability level) were found between the proposed and reference methods. The method is rapid, reliable, precise and free of interferences.