Application of Anodic Stripping Differential Alternative Pulses Voltammetry for Simultaneous Species Quantification

The second order voltammetric technique Differential Alternative Pulses Voltammetry (DAPV) was applied in anodic stripping mode for simultaneous quantification of traces of species having close E_1/2. The potential‐time waveform and the signal processing allowing the DAPV application in stripping mode are presented. The pulses widths and amplitudes were optimized to obtain maximal sensitivity and resolution at traces of In³⁺ and Cd²⁺ (having E_1/2 difference of 45 mV) simultaneous quantification in presence of excess of Pb²⁺. Precise results for both species concentrations were obtained up to In³⁺ to Cd²⁺ concentration ratio as high as 1 to 10 without any sample pre‐treatment in purified industrial waste waters using 0.1 mol L⁻¹ HCl as supporting electrolyte.     

Electrochemical Determination of Cd2+ and Pb2+ Using NSAID‐mefenamic Acid Functionalized Mesoporous Carbon Microspheres Modified Glassy Carbon Electrode

This paper describes the electrochemical behaviors of Cd²⁺ and Pb²⁺ on the proposed mesoporous carbon microspheres/mefenamic acid/nafion modified glassy carbon electrode (MC/MA/Nafion/GC) studied by square wave anodic stripping voltammetry (SWASV). The prepared material is characterized by XRD, SEM, FTIR, RAMAN and BET analysis. Experimental parameters, such as the deposition potential and time, the pH value of buffer solution were optimized. Under the optimized conditions, the electrode responded linearly to Cd²⁺ and Pb²⁺ in the concentration range from 50 to 300 nM, and the detection limits were 24.2 and 11.26 nM respectively. The sensitivity determined was 0.0623 μA/nM (Cd²⁺) and 0.192 μA/nM (Pb²⁺). Multiple metal ion detection with clear demarcation of peaks was produced by the electrode. Moreover, the modified electrode has possessed good selectivity and reproducibility of Cd²⁺ and Pb²⁺ detection. We also investigated the interference of various anions and surfactants for the detection of Cd²⁺ and Pb²⁺ ions. Finally the modified electrode was used to detect the presence of metal ions in practical samples and the results obtained are comparatively good with respect to AAS.     

Synthesis of lariat organochalcogenoethers based on azacalix[3]arenes for the potentiometric detection of [UO2] ions

The syntheses of organochalcogen-supported azacalix[3]arenes are described in a one-pot manner in satisfactory yields. A remarkably selective potentiometric response was accomplished for uranyl ions over a variety of other metal ions, including alkali (Na⁺, K⁺), alkaline-earth (Mg²⁺, Ca²⁺, Ba²⁺), transition and heavy metal ions (Co²⁺, Ni²⁺, Cu²⁺, Ag⁺, Fe³⁺, Zn²⁺, Cd²⁺ and Pb²⁺) using an ion-selective electrode based on compound 3 incorporated into a polymeric (PVC) membrane.     

Bifunctional polydopamine@Fe3O4 core–shell nanoparticles for electrochemical determination of lead(II) and cadmium(II)

The present paper has focused on the potential application of the bifunctional polydopamine@Fe₃O₄ core–shell nanoparticles for development of a simple, stable and highly selective electrochemical method for metal ions monitoring in real samples. The electrochemical method is based on electrochemical preconcentration/reduction of metal ions onto a polydopamine@Fe₃O₄ modified magnetic glassy carbon electrode at −1.1 V (versus SCE) in 0.1 M pH 5.0 acetate solution containing Pb²⁺ and Cd²⁺ during 160 s, followed by subsequent anodic stripping. The proposed method has been demonstrated highly selective and sensitive detection of Pb²⁺ and Cd²⁺, with the calculated detection limits of 1.4 × 10⁻¹¹ M and 9.2 × 10⁻¹¹ M. Under the optimized conditions, the square wave anodic stripping voltammetry response of the modified electrode to Pb²⁺ (or Cd²⁺) shows a linear concentration range of 5.0–600 nM (or 20–590 nM) with a correlation coefficient of 0.997 (or 0.994). Further, the proposed method has been performed to successfully detect Pb²⁺ and Cd²⁺ in aqueous effluent.     

Determination of Trace Lead and Cadmium in Water Samples by Anodic Stripping Voltammetry with a Nafion‐Ionic Liquid‐Coated Bismuth Film Electrode

A new chemically modified bismuth film electrode coated with an ionic liquid [(1‐ethyl‐3‐methylimidazolium tetracyanoborate (EMIM TCB)] and Nafion was developed for the simultaneous determination Pb²⁺ and Cd²⁺ by anodic stripping voltammetry. Compared with conventional bismuth film electrodes, this electrode exhibited greatly improved electrochemical activity for Pb²⁺ and Cd²⁺ detection due to the unique properties of Nafion polymer and ionic liquid. The key experimental parameters related to the fabrication of the electrode and the voltammetric measurements were optimized on the basis of the stripping signals, where the peak currents increased linearly with the metal concentrations in a range of 10–120 µg L^?1 with a detect limit of 0.2 µg L^?1 for Pb²⁺, and 0.5 µg L^?1 for Cd²⁺ for 120s deposition. High reproducibility was indicated from the relative standard deviations (1.9 and 2.5 %) for nine repetitive measurements of 20 µg L^?1 Pb²⁺ and Cd²⁺, respectively. In addition, the surface characteristics of the modified BiFE were investigated by scanning electron microscopy (SEM), and results showed that fibril‐like bismuth nanostructures were formed on the porous Nafion polymer matrix. Finally, the developed electrode was applied to determine Pb²⁺ and Cd²⁺ in water samples, indicating that this electrode was sensitive, reliable and effective for the simultaneous determination of Pb²⁺ and Cd²⁺.     

Electrochemical determination of cadmium and lead based on the joint enhancement effects of SBA-16 and iodide

Mesoporous SBA-16 was synthesized using tetraethoxysilane as silicon source and a ternary system consisting of surfactant F127, water and butanol. Owing to the excellent properties of SBA-16 such as lager surface area and strong accumulation ability, the stripping peak current of Cd²⁺ and Pb²⁺ remarkably increases at the SBA-16 modified carbon paste electrode. Moreover, the peak current of Cd²⁺ and Pb²⁺ further enhances after the addition of I^?. Under the joint enhancement effects of SBA-16 and I^?, the detection sensitivity of Cd²⁺ and Pb²⁺ is greatly improved. The influences of concentration of I^?, amount of SBA-16, accumulation potential and time were investigated. As a result, a new electrochemical method with high sensitivity was developed for the simultaneous determination of Cd²⁺ and Pb²⁺. The limit of detection is 0.6 nM for Cd²⁺ and 1 nM for Pb²⁺. It was used to determine Cd²⁺ and Pb²⁺ in waste water sample, and the results consisted with the values that obtained by atomic absorption spectrometry.     

Simultaneous determination of lead(II) and cadmium(II) at a diacetyldioxime modified carbon paste electrode by differential pulse stripping voltammetry

A simple and effective chemically modified carbon paste electrode (CMCPE) for the simultaneous determination of lead(II) and cadmium(II) was developed in this work. The electrode was prepared by the addition of diacetyldioxime into a carbon paste mixture. Pb²⁺ and Cd²⁺ were preconcentrated on the surface of the modified electrode by complexing with diacetyldioxime and reduced at a negative potential (−1.10 V). Then the reduced products were oxidized by differential pulse stripping. The fact that two stripping peaks appeared on the voltammograms at the potentials of −0.65 V (Cd²⁺) and −0.91 V (Pb²⁺) demonstrates the possibility of simultaneous determination of Pb²⁺ and Cd²⁺. Under the optimized working conditions, calibration graphs were linear in the concentration ranges of 1.0×10⁻⁷-1.5×10⁻⁵ mol l⁻¹ (Pb²⁺) and 2.5×10⁻⁷-2.5×10⁻⁵ mol l⁻¹ (Cd²⁺), respectively. For 5 min preconcentration, detection limits of 1×10⁻⁸ mol l⁻¹ (Pb²⁺) and 4×10⁻⁸ mol l⁻¹ (Cd²⁺) were obtained at the signal noise ratio (SNR) of 3. To evaluate the reproducibility of the newly developed electrode, the measurements of 5×10⁻⁷ mol l⁻¹ Pb²⁺ and Cd²⁺ were parallel carried out for six times at different electrodes and the relative standard deviations were 2.9% (Pb²⁺) and 3.2% (Cd²⁺), respectively. Interferences by some metals were investigated. Only Ni²⁺ and Hg²⁺ apparently affected the peak currents of Pb²⁺ and Cd²⁺. The diacetyldioxime modified carbon paste electrode was applied to the determination of Pb²⁺ and Cd²⁺ in water samples. The results indicate that this electrode is sensitive and effective for the simultaneous determination of Pb²⁺ and Cd²⁺.     

Simultaneous Titration of Ternary Mixtures of Pb(II), Cd(II) and Cu(II) with Potentiometric Electronic Tongue Detection

An automatic titration method is reported to resolve ternary mixtures of transition metals (Pb²⁺, Cd²⁺ and Cu²⁺) employing electronic tongue detection and a reduced number of pre‐defined additions of EDTA titrant. Sensors used were PVC membrane selective electrodes with generic response to heavy‐metals, plus an artificial neural network response model. Detection limits obtained were ca. 1 mg L^?1 for the three target ions and reproducibilities 3.0 % for Pb²⁺, 4.1 % for Cd²⁺ and 5.2 % for Cu²⁺. The system was applied to contaminated soil samples and high accuracy was obtained for the determination of Pb²⁺. In the determination Cd²⁺ and Cu²⁺, sample matrix showed a significant effect.     

Gamma irradiation-induced Cd2+ and Pb2+ removal from different kinds of water

Gamma irradiation-induced removal of cadmium ion (Cd²⁺) and lead ion (Pb²⁺) in different kinds of water was investigated. It is observed that solution pH, dissolved oxygen (DO) concentration, sodium carbonate and EDTA played an important effect on Cd²⁺ and Pb²⁺ removal. Low solution pH, low DO concentration and sodium carbonate were favorable for removal of Cd²⁺ and Pb²⁺ by reducing species, while the presence of EDTA in solution restrained Cd²⁺ and Pb²⁺ reduction. Pb²⁺ removal percentage was higher compared to that of Cd²⁺ at the same experimental conditions. Cd²⁺ and Pb²⁺ removal under different conditions was well described by the pseudo-first-order kinetics model. Cd²⁺ and Pb²⁺ removal in different water followed an increasing order: water inflow<surface water<effluent<ground water. In addition, gamma irradiation resulted in a slight decrease in pH and TOC values of water inflow of municipal sewage treatment plant.     

Competitive Potentiometric Study of the Thermodynamics of Complexation of Some Transition and Heavy Metal Ions with Dibenzopyridino-18-crown-6 in Methanol using Ag+ Ion as a Probe

The complexation of dibenzopyridino-18-crown-6 with some transition and heavy metal ions in methanol solution at various temperatures was studied by a competitive potentiometric method using a Ag⁺/Agelectrode system. The stoichiometry and stability of the resulting complexes were computed by the MINIQUAD program. The stability of the resulting complexes varied in the order Ag⁺ > Pb²⁺ > Tl⁺ > Cu²⁺ > Cd²⁺ > Zn²⁺. The enthalpy and entropy of the resulting 1:1 complexeswere evaluated from the temperature dependence of the stability constants.The complexes of all cations were enthalpy-stabilized but entropy-destabilized,except for Ag⁺ and Pb²⁺ ions,which were also entropy-stabilized.     

Anodic Stripping Voltammetry of Heavy Metals on a Metal Catalyst Free Carbon Nanotube Electrode

Anodic stripping voltammetry (ASV) determination of Pb²⁺, Cd²⁺, and Zn²⁺ was done using metal catalyst free carbon nanotube (MCFCN) electrodes. Osteryoung square wave stripping voltammetry (OSWSV) was selected for detection. The MCFCNTs are synthesized via Carbo Thermal Carbide Conversion method which leads to residual transition metal free in the CNT structure. The new material shows very good results in detecting heavy metal ions, such as Pb²⁺, Cd²⁺, and Zn²⁺. The calculated limits of detection were 13 nM, 32 nM and 50 nM for Pb²⁺, Cd²⁺ and Zn²⁺, respectively with a deposition time of 150 s.     

Comparison of sorption of Pb<Superscript>2+</Superscript> and Cd<Superscript>2+</Superscript> on Kaolinite clay and polyvinyl alcohol-modified Kaolinite clay

Kaolinite clay obtained from Ubulu-Ukwu, Delta state in Nigeria was modified with polyvinyl alcohol (PVA) reagent to obtain PVA-modified Kaolinite clay adsorbent. Scanning Electron Microscopy (SEM) of the PVA-modified adsorbent suggests that Kaolinite clay particles were made more compact in nature with no definite structure. Modification of Kaolinite clay with PVA increased its adsorption capacity for 300 mg/L Pb²⁺ and Cd²⁺ by a factor of at least 6, i.e., from 4.5 mg/g to 36.23 mg/g and from 4.38 mg/g to 29.85 mg/g, respectively, at 298 K. Binary mixtures of Pb²⁺ and Cd²⁺ decreased the adsorption capacity of Unmodified Kaolinite clay for Pb²⁺ by 26.3% and for Cd²⁺ by 0.07%, respectively. In contrast, for PVA-modified Kaolinite clay, the reductions were up to 50.9% and 58.5% for Pb²⁺ and Cd²⁺, respectively. The adsorption data of Pb²⁺ and Cd²⁺ onto both Unmodified and PVA-modified Kaolinite clay adsorbents were found to fit the Pseudo-Second Order Kinetic model (PSOM), indicating that adsorption on both surfaces was mainly by chemisorption and is concentration dependent. However, kinetic adsorption data from both adsorbent generally failed the Pseudo-First order Kinetic model (PFOM) test. Extents of desorption of 91% Pb²⁺ and 94% Cd²⁺ were obtained, using 0.1 M HCl, for the Unmodified Kaolinite clay adsorbent. It was found that 99% Pb²⁺ and 97% Cd²⁺, were desorbed, for PVA-modified Kaolinite clay adsorbents within 3 min for 60 mg/L of the metal ions adsorbed by the adsorbents.     

Potentiometric Sensing of Heavy Metal Ions Using a Novel Zeolite Y Membrane

The application of zeolite Y membranes to the potentiometric sensing of heavy metal ions is described. Membranes are prepared from a pressed disk of zeolite Y, treated using tetraethyl orthosilicate (TEOS) as a silica source. The resulting silica‐zeolite Y composite membranes are characterized by powder X‐ray diffraction, MAS NMR and their potentiometric response to cations with a diameter greater than the zeolite Y pore. The initial response to cadmium (Cd²⁺) and lead (Pb²⁺) ions obeys the Nernst equation, including appropriate corrections for non‐ideality, although the responses decay over a time‐scale of several hours for higher concentration ratios.     

Synthesis and application of imprinted polyvinylimidazole-silica hybrid copolymer for Pb determination by flow-injection thermospray flame furnace atomic absorption spectrometry

A novel ion imprinted polyvinylimidazole-silica hybrid copolymer (IIHC) was synthesized and used as a selective solid sorbent for Pb²⁺ ions preconcentration using an on-line solid phase extraction (SPE) system coupled to TS-FF-AAS. The ionic hybrid sorbent was prepared using 1-vinylimidazole and 3-(trimethoxysilyl)propylmethacrylate as monomers, Pb²⁺ ions as template, tetraethoxysilane as reticulating agent and 2,2′-azobis-isobutyronitrile as initiator. The best on-line SPE conditions concerning sorption behavior, including sample pH (6.46), buffer concentration (9.0 mmol L⁻¹), eluent (HNO₃) concentration (0.5 mol L⁻¹) and preconcentration flow rate (4.0 mL min⁻¹), were optimized by means of full factorial design and Doehlert matrix. The analytical curve ranged from 2.5 to 65.0 μg L⁻¹ (r = 0.999) with limit of detection of 0.75 μg L⁻¹; the precision (repeatability) calculated as relative standard deviation (n = 10) was 5.0 and 3.6% for Pb²⁺ concentration of 10.0 and 60.0 μg L⁻¹, respectively. From on-line breakthrough curve, column capacity was 3.5 mg g⁻¹. Preconcentration factor (PF), consumptive index (CI) and concentration efficiency (CE) were 128.0, 0.16 mL and 25.6 min⁻¹, respectively. The selective performance of the sorbent, based on relative selectivity coefficient, was compared to NIC (non imprinted copolymer) for the binary mixture Pb²⁺/Cd²⁺, Pb²⁺/Cu²⁺ and Pb²⁺/Zn²⁺. The results showed that ion imprinted polyvinylimidazole-silica hybrid polymer had higher selectivity for Pb²⁺ than NIC at 64.9, 16.0 and 8.8 folds. The developed method was successfully applied for highly sensitive and selective Pb²⁺ determination in different kinds of water samples, parenteral solutions and urine. Accuracy was also assessed by analyzing certified reference fish protein (DORM-3) and marine sediment (MESS-3 and PACS-2) with satisfactory results.     

Complexation of iminodisuccinic acid (IDS) and 3-hydroxy-2,2′-iminodisuccinic acid (HIDS) with Cd2+, Hg2+, and Pb2+ in aqueous solution

In a search for environmentally friendly metal-chelating ligands for industrial applications, the protonation and complex formation equilibria of iminodisuccinic acid (IDS) and 3-hydroxy-2,2′-iminodisuccinic acid (HIDS) with Cd²⁺, Hg²⁺, and Pb²⁺ in aqueous 0.1?mol?L^?1 NaNO₃ solution were studied at 25°C by potentiometric titration. Models for complexation and stability constants of the different complexes were determined for each metal ion using the computer program SUPERQUAD. In all cases, complex formation was dominated by stable ML^2? complexes.     

Calibrationless determination of cadmium, lead and copper in rain samples by stripping voltammetry at mercury microelectrodes: Effect of natural convection on the deposition step

Mercury microelectrodes were prepared by ex situ deposition of Hg onto Pt microdiscs. By exploiting the known properties of microelectrodes in stripping analysis, an absolute method based on a simple equation derived from the stripping charge and the microelectrode steady-state current was assessed for the simultaneous quantification of Cd²⁺, Pb²⁺ and Cu²⁺ concentrations. The method was tested with synthetic solutions containing known amounts of Cd²⁺, Pb²⁺ and Cu²⁺. Then, it was used to determine the labile and total fractions of these metal ions in rain samples. The labile fractions were measured from samples at their natural pH while the total concentrations were determined from samples at pH=2.     

SBA-15/Metformin as a novel sorbent combined with surfactant-assisted dispersive liquid–liquid microextraction (SA-DLLME) for highly sensitive determination of Pb,Cd and Ni in food and environmental samples

This paper established a new, rapid and sensitive method for the ultra-trace determination of lead, cadmium and nickel in food and environmental samples preconcentrated by dispersive solid-phase extraction (DSPE) combined with surfactant-assisted dispersive liquid–liquid microextraction (SA-DLLME) prior to graphite furnace atomic absorption spectrometry. SBA-15/Met was synthesized and used as a new efficient sorbent for the extraction of metal ions in DSPE. It was characterized by TEM and TGA techniques. After DSPE step, stripped metal elements were complexed with dithizone, and then, the complexes were extracted into carbon tetrachloride by using SA-DLLME. A conventional nonionic surfactant, triton X-100 was used as a disperser agent. Under the optimized conditions, the limit of quantifications was found to be 2.5 ng L^?1 for Pb²⁺, Cd²⁺ and 5.0 ng L^?1 for Ni²⁺. The limits of detection were 1.5 ng L^?1 for Ni²⁺ and 0.75 ng L^?1 for Pb²⁺ and Cd²⁺, with enrichment factor of 1650. The optimized method exhibited a good precision level with relative standard deviations (RSDs%) values of 4.9, 5.2 and 5.0% for 1 μg L^?1 Pb²⁺, Cd²⁺ and Ni²⁺, respectively (n = 7). Application of the proposed method to the analysis of fish-certified reference material produced results that were in good agreement with the certified values.     

Synthesis and characterisation of poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) Zr(IV) monothiophosphate composite cation exchanger: analytical application as lead ion selective membrane electrode

A Pb²⁺ ion selective membrane electrode based on poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) Zr(IV) monothiophosphate composite cation exchange material was fabricated using solution casting method. The effect of membrane composition on the proton exchange capacity was investigated by using varying amounts of electroactive material. The membrane with 250 mg of electroactive material and 10 µL of plasticiser exhibited higher proton conductivity. The optimised membrane composition was used for the fabrication of ion selective membrane electrode which exhibited typical Nernstian response towards Pb²⁺ ions in the concentration range 20.70 gL^?1–20.7 µgL^?1 (1 × 10^–1–1 × 10^–7 mol L^?1) with a sub-Nernstian slope of 27.429 mV per decade change in Pb²⁺ ion concentration. The response time of the electrode under study for Pb²⁺ ions was found to be 11 s and the electrode can be used for 120 days without any considerable divergence in response potential. It can also be successfully used in the pH range from 3.0 to 6.5. It was found selective for Pb²⁺ ions in the presence of various monovalent, divalent and trivalent interfering metal ions. It was also employed as an indicator electrode in the potentiometric titration of Pb²⁺ ions using ethylenediaminetetraacetic acid, disodium salt, as a titrant.     

The Fabrication and Characterization of a Bismuth Nanoparticle Modified Boron Doped Diamond Electrode and Its Application to the Simultaneous Determination of Cadmium(II) And Lead(II)

We report the simultaneous electroanalytical determination of Pb²⁺ and Cd²⁺ by square‐wave anodic stripping voltammetry (SWASV) using a bismuth nanoparticle modified boron doped diamond (Bi‐BDD) electrode. Bi deposition was performed in situ with the analytes, from a solution of 0.1 mM Bi(NO₃)₃ in 0.1 M HClO₄ (pH 1.2), and gave detection limits of 1.9 μg L^?1 and 2.3 μg L^?1 for Pb(II) and Cd(II) respectively. Pb²⁺ and Cd²⁺ could not be detected simultaneously at a bare BDD electrode, whilst on a bulk Bi macro electrode (BiBE) the limits of detection for the simultaneous determination of Pb²⁺ and Cd²⁺ were ca. ten times higher.     

Transition Metal Ion-binding Properties of a 14-Membered N2O2S2- Macrobicyclic Ligand

The selective liquid–liquid extraction of various transition metal cations from the aqueous phase to the organic phase was carried out using a 14-membered N₂O₂S₂-macrobicycle. Metal picrates such as Pb²⁺, Co²⁺, Zn²⁺, Ni²⁺,Cu²⁺ and Cd²⁺ were used in this extraction studies. It was found that the ligand showed moderate selectivity towards Pb²⁺ only among the other metals. The extraction constant (log K _ex) was determined to be 13.8 for Pb²⁺ complex.