Application of tryptamine as a derivatising agent for airborne isocyanate determination. Part 3. Evaluation of total isocyanates analysis by high-performance liquid chromatography with fluorescence and amperometric detection

Determination of total airborne isocyanates using tryptamine as the derivatising agent was investigated. Tryptamine derivatised isocyanates were analysed by reversed-phase high-performance liquid chromatography (HPLC). The column was equipped with dual detectors of fluorescence emission and amperometric oxidation. The characteristics of fluorescence emission and amperometric oxidation of tryptamine were retained even after its reaction with isocyanates. With this unique behaviour, all tryptamine derivatised isocyanates can be quantified using HPLC by employing a single, pure derivative, such as tryptamine derivatised hexamethylene diisocyanate as the calibration standard. This is especially important for analysing polymeric isocyanates when identical calibration standards are not always available. The applicability of this method for air sampling was evaluated by comparison with the established method of Bagon et al. involving 1-(2-methoxyphenyl)piperazine. Simulation of air sampling was performed in a Test Atmosphere Generation System by the vaporisation of toluene diisocyanate. Satisfactory results were obtained, indicating the applicability of this technique for the determination of total airborne isocyanates.     

Polarographic determination of methyl methacrylate

The permanganate oxidation of methyl methacrylate in weakly acidic solution yields methyl pyruvate. Hydroxylamine hydrochloride is used for destroying the excess of permanganate. At the same time it is consumed for oximation of the pyruvate, and the resulting oxime is determined polarographically. The reaction scheme of permanganate oxidation of methyl methacrylate is suggested and optimum working conditions are found both for permanganate oxidation and for polarographic determination. The method is used for the determination of vapours of methyl methacrylate in the air, for industrial hygiene purposes.     

Ferrocenoyl piperazide as derivatizing agent for the analysis of isocyanates and related compounds using liquid chromatography/electrochemistry/mass spectrometry (LC/EC/MS)

Ferrocenoyl piperazide is introduced as a new pre-column derivatizing agent for the analysis of various isocyanates in air samples using reversed-phase liquid chromatographic separation, electrochemical oxidation/ionization, and mass spectrometry. The nonpolar derivatives can be separated well using a phenyl-modified stationary phase and a formic acid/ammonium formate buffer of pH 3, which yields excellent separations, especially for one problematic group of isocyanates consisting of 2,4- and 2,6-toluylenediisocyanate (2,4- and 2,6-TDI) and hexamethylenediisocyanate (HDI). Electrochemical oxidation at low potentials (0.5 V versus Pd/H(2)) leads to formation of charged products, which are nebulized in a commercial atmospheric pressure chemical ionization (APCI) source, with the corona discharge operated only at low voltage. Limits of detection between 6 and 20 nmol/L are obtained for the isocyanate derivatives, and calibration is linear over at least two decades of concentration. The method is applied for the analysis of air after thermal degradation of a polyurethane foam, and it is demonstrated that it is suitable as well for the analysis of carboxylic acid chlorides and of isothiocyanates.     

Determination of airborne isocyanates

Isocyanates are important in industrial hygiene and workplace monitoring. Owing to their severe acute toxicity and sensitizing properties, analytical methods with high sampling efficiency and sensitivity in the low ppb to ppt range are required. The reactivity of isocyanates necessitates initial derivatization with nucleophilic agents—usually amines—for stabilization and enrichment; this is often followed by chromatographic separation with spectroscopic, electrochemical, or mass spectrometric detection. Sampling strategies for airborne isocyanates comprise active, i.e. pumped, or passive, i.e. diffusive, methods; the method selected depends on the application. Whereas active methods rely mainly on impingers, reagent-coated filters, or sampling tubes, passive samplers make use of reagent-coated filters, the surface of which is connected to the air sample by diffusion channels. Because airborne isocyanates are prone to occur in different forms, i.e. as vapors, as aerosols, or adsorbed on particulate matter, denuder sampling has been introduced, thus enabling simultaneous collection of gaseous and aerosol isocyanates. The first part of this review summarizes chemical methods and reagents which have been introduced for derivatization of airborne isocyanates. The advantages and drawbacks of the individual derivatization procedures and their combination with different detection principles are evaluated. In the second part, the most recent developments in air sampling for isocyanates, with special focus on diffusive sampling, are reviewed and critically discussed.     

Ethanol removal from fermentation broth by gas membrane extraction

A new type of membrane extraction for in situ removal of ethanol from fermentation broth is presented. Aqueous solutions of propylene glycol are used as extractants. The extractatant and the broth are separated by a microporous hydrophobic membrane which is not penetrated by the broth or by the extractant. As a consequence a thin gas layer, essentially air, is immobilised within the membrane pores and separates the two liquid phases (i.e. a gas membrane). Vapour-liquid equilibria are established at both membrane sides; because glycols reduce the ethanol content of the equilibrium vapour phase with respect to the binary system, ethanol vapours preferentially diffuse through the stagnant gas layer.     

Workplace monitoring of isocyanates using ion trap liquid chromatography/tandem mass spectrometry

A sensitive liquid chromatography/ion trap tandem mass spectrometry method was developed for the qualitative and quantitative detection of isocyanates in air. The method is based on derivatization of isocyanates with 1-(2-methoxyphenyl)piperazine during air sampling. The extracts are analyzed using an ion trap LC/MS system equipped with an electrospray (ESI) ion source. The method shows high linearity, specificity, accuracy and precision. The limits of detection are 40x to 55x lower than with UV-based methods.     

Determination of surface heterogeneity profiles on graphite by finite concentration inverse gas chromatography

Inverse gas chromatography (IGC) is an established tool in the determination of the adsorption potential distribution function. This function reflects the energetic heterogeneity profile of a surface and therefore provides interesting information on the nature and population of different surface sites. IGC is shown to be a fast and accurate technique for the determination of the adsorption potential distribution function of two different graphite samples. In this paper the adsorption of acidic and basic organic vapours is studied. Unlike heterogeneity profiles determined by nitrogen measurements, experiments with polar vapours can provide additional information on the adsorption mechanism and polar sorption sites. The heterogeneity profiles of all probes used are significantly different from one another and allow discreet energy levels to be distinguished. Chemically different probes reveal different adsorption mechanisms for the graphite surface.     

Determination of isocyanates in air

Procedures for the determination of isocyanates in air are considered, including procedures for air sampling with the subsequent analysis and on-line monitoring procedures. Only chemisorption is used for the sampling and preconcentration of isocyanates because of their high reactivity. The data on the reagents in use, the types of sampling devices, and operation conditions are surveyed. Presently, high-performance liquid chromatography is primarily used for the subsequent instrumental analysis of samples. Photometric techniques were used in early studies; more recently, thin-layer chromatography and gas chromatography were introduced. Examples of analysis using other techniques are very few. Methods of on-line monitoring of air (both instrumental techniques and rapidly developed biomonitoring, which is performed simultaneously with the analysis of polluted air) are briefly considered.     

An all-solid photoelectrochemical cell for the photooxidation of organic vapours under ultraviolet and visible light illumination

An all-solid photoelectrochemical cell has been tested in the photooxidation of methanol vapours as a proof-of-concept for the application of electrochemically enhanced photocatalysis in air treatment. The cell was based on a Nafion^®-impregnated microporous membrane that served as the solid polymer electrolyte. The working and reference electrodes (a TiO₂/WO₃-coated stainless steel mesh and AgCl-coated Ag wire, respectively) were adhered with the addition of a Nafion^® solution onto one face of the membrane, while the counter electrode (a plain stainless steel mesh) was attached to its opposite face. The use of an electrosynthesized TiO₂/WO₃ photoelectrode allowed the utilization of both UV and visible light. The device was tested by constant potential photoamperometry in air streams saturated with water or water–methanol vapours and the obtained photocurrent increased with increasing methanol levels, confirming the photoelectrochemical oxidation of methanol vapours under UV and visible light illumination.     

An optimized sampling and GC-MS analysis method for benzene in exhaled breath, as a biomarker for occupational exposure

Benzene is known to be toxic and carcinogenic: therefore, in case of exposure to benzene vapours, a reliable biological monitoring procedure is needed, particularly in the field of occupational hygiene. The determination of the concentration of benzene in the exhaled air 8 h after the exposure has been demonstrated to be a significant biomarker, even for low concentrations of airborne benzene vapours. This work presents a sampling and analysis method that optimizes previously described procedures: in the sampling phase, a double-step sample collection in Tedlar bags is used, in order to remove the breath moisture and to standardise the sample volumes. The analytical phase uses a cryogenic trap for the concentration of the air samples to be injected in the GC-MS, without the need for trapping materials, significantly reducing time and costs of the analysis and improving sensitivity. The presented method has been successfully applied to the biological monitoring of a mixed population (occupationally exposed and not exposed subjects, smokers and non-smokers), with a lower detection limit of 1.5 ng of benzene per litre of exhaled air, that is 1/200 of the biological exposure index recommended by the American Conference of Governmental Hygienists.     

Influence of surface reactions on original ESR signals of powdered samples Zn3P2

Preliminary investigations of Zn₃P₂ single crystals suggested two models of surface reactions with wet air. ESR paramagnetic signals have been observed in powdered samples. The influence of surface reactions of saturated vapours of H₂O in the presence of air at room temperature, as well as annealing with phosphorus and heating at 500°C under vacuum on the original ESR signals has been studied. The results of these treatments on the ESR signal strongly depend on the type of samples: high or low electrical resistivity, related to the amount of phosphorus in the Zn₃P₂ structure.     

Lewis acid-controlled reactions of zirconacyclopentadienes with isocyanates and isothiocyanates. One-pot three- or four-component synthesis of multiply substituted iminocyclopentadienes and butadiene-tethered 1,6-bisamides and electrophilic cyclization

Multiply substituted zirconacyclopentadienes including bicyclic zirconacyclopentadienes and zirconaindenes reacted with isocyanates and isothiocyanates in the presence of Lewis acids to afford iminocyclopentadienes and conjugated 1,6-bisamides, depending on the nature of Lewis acids, isocyanates, and isothiocyanates used. Only in the presence of BF₃ could iminocyclopentadienes be obtained in high isolated yields when zirconacyclopentadienes were treated with isocyanates. On the contrary, BF₃ could not mediate the reaction of zirconacyclopentadienes with isothiocyanates. For the reactions of zirconacyclopentadienes with isothiocyanates, EtAlCl₂ was found effective to generate iminocyclopentadienes as the products. Interestingly, however, for the reactions of zirconacyclopentadienes with isocyanates, EtAlCl₂ was found to work very differently from BF₃. Instead of iminocyclopentadienes, conjugated 1,6-bisamides and conjugated mono-amides were obtained as products in high isolated yields from the reactions of zirconacyclopentadienes with isocyanates, depending on the substituents of isocyanates. The reaction path and products could be controlled by Lewis acids. As a demonstration of the usefulness of thus obtained unsaturated bisamides, electrophilic cyclization using acids, NBS, and I₂ was carried out. Electrophilic cyclization of multisubstituted conjugated 1,6-bisamide derivatives afforded cyclic iminoethers in excellent yields with perfect selectivity. Only one of the amide groups took part in the electrophilic cyclization.     

Structure Based Library Approach to Photosynthesis Inhibitors:The Solid Phase Synthesis of Hydro-Uracils and Thiouracils

Combinatorialchemistryhasemergedasanefficienttoolforchedriststosynthesize"comPoundslibraries"fortheraPididentificationandoPtforizationofnewleads-lSolidphaseorganicsynthesisprovidesaraPidmeansforpreparationofcomPoundslibraries,andhasbeenusedfortheconstrUctionofoligomericcomPounds,'andsmallorganicmoleculessuchasbenzodiazepine,'9-lactams,'andquinolones.'ThemajortargetfortheinhibitionofphotosystemII(PSII)istheDlprotein,apolyPePtidewithamolecularweightof32kDa.'Wehavedevelopedmodelsoftheher-b…     

Superbase promoted synthesis of dienamides as useful intermediates for the synthesis of α-ketoamides, γ-lactams and cyclic imino ethers

Alkoxydienamides 2 have been synthesized exploiting the reactivity of α,β-unsaturated acetals 1 with isocyanates in the presence of Schlosser's superbase LIC-KOR. In a mild acidic medium, 2 can then be promptly converted both into α-ketoamides 3 and into substituted 2-pyrrolidinones 4 or imino ethers 5 by choosing the appropriate experimental conditions.     

Well-ordered self-assembled monolayers created via vapor-phase reactions on a monolayer template

The reaction of vapor-phase alkyl isocyanates (O=C=N-(CH2)n-1CH3) with OH-terminated alkanethiol template monolayers on Au produces well-organized self-assembled monolayers, containing intrachain carbamate linkages (Au/S(CH2)16O(C=O)NH(CH2)n-1CH3, where n = 1-8, 11, and 12). X-ray photoelectron spectroscopy, contact angle goniometry, and reflection absorption infrared spectroscopy suggest that the template surface completely reacts with the isocyanates yielding a monolayer that contains an interchain hydrogen-bonded carbamate network. Spectroscopic data indicates that the alkyl underlayer remains well ordered following reaction with the isocyanates. The order of the overlayer and the hydrogen-bonding interactions between adjacent chains increase as a function of the alkyl isocyanate chain length, n. The overlayer appears to be well ordered for n > or = 5.     

Development of a Piezoelectric Crystal Sorption Detector for Monitoring of Total Organic Compounds in Air

Abstract

A light and portable organic vapours monitor has been developed using piezoelectric (P/Z) quartz crystal to determine Volatile Organic Compounds (VOCs) commonly found in workplace air. Out of the eight coating material studied, High Vacuum Grease (HVG) was found to be the best for determining commonly encountered organic vapours such as 1,1,1-Trichloroethane, Chloroform, Benzene and Toluene in room air. The optimised coating weight was 23 μg HVG at a flow rate of 200 mL/min. Moisture was found to interfere and the use of a Nafion gas dryer was found to reduce the relative humidity to a constant 37 % for room air with 43–81 % relative humidity. Under optimised conditions, a mean sensitivity of 1.9 × 1^?2 Hz/ppm was obtained for total VOCs with 17.2% RSD variation towards different VOCs. Excellent linear working ranges were obtained from 40 to 2400 ppm (v/v), with response time and recovery time within one minute up to 500 ppm (v/v) of analyte. High and relatively constant response factors were obtained for different VOCs. The reliability of the mcthod has been established by parallel method comparison using established GC-FID method. The P/Z detector developed could also be used to monitor individual VOCs.     

Computerized capillary gas chromatographic analysis of hydrocarbon mixtures in workplace air

The quantitative composition of white spirit vapours in workplace air may differ considerably from the solvent being used, although all components are the same. By calculating the hygienic effect from the threshold limit value (NGV) of each component, a more reliable estimate is obtained of the occupational hazard than by using the NGV for white spirit. In this method the analyses were performed by on-column injection onto a temperature-programmed capillary column. Retention indices based on n-paraffins and isooctane were calculated using spline functions. Index tables were established for different hydrocarbon mixtures. The validity of the retention indices was found to be satisfactory, depending on the stability of the column and the possibility of optimizing the indices when replacing one column by another of the same type and dimensions. Comparisons were made with alternative methods for determining the concentration of white spirit vapours in air samples. A polar column was used to check the total content of aromatics.     

Nickel-catalyzed synthesis of acrylamides from alpha-olefins and isocyanates

[reaction: see text] The nickel(0)-catalyzed coupling of alpha-olefins and isocyanates proceeds in the presence of the N-heterocyclic carbene ligand IPr to provide alpha,beta-unsaturated amides. Carbon-carbon bond formation occurs preferentially at the 2-position of the olefin. The N-tert-butyl amide products can be converted to the corresponding primary amides under acidic conditions.     

Vapour permeation and sorption in fluoropolymer gel membrane based on ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethylsulphonyl)imide

The emissions of hydrocarbons from fossil fuels into atmosphere entail both an economic loss and an environmental pollution. Membrane separations can be used for vapour recovery and/or vapour removal from the permanent gas stream, given that the appropriate membrane is identified. A neat poly(vinylidene fluoride-co-hexafluoropropylene) membrane is impermeable to both the representatives of aliphatic hydrocarbons and branched hydrocarbons, namely hexane and isooctane, whereas the permeation flux is enhanced by the presence of 80 mass % of the ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethylsulphonyl)imide in the membrane, as detailed in this work. The permeabilities of hydrocarbon vapours were determined from the binary mixture containing hydrocarbon and nitrogen to simulate the real input of an air stream containing a condensable hydrocarbon. The diffusion coefficient determined from sorption measurements was higher for hexane, as would be expected for a smaller molecule, whereas both the sorption isotherms and permeabilities of the hydrocarbons studied were found to be almost identical. It is possible that the sorption effect predominates in the transport mechanism for VOCs/N₂ separations.     

Application of solid-phase microextraction for determination of organic vapours in gaseous matrices

This paper reviews the practical applications of solid-phase microextraction (SPME) in the analysis of organic vapours which are pollutants of atmospheric air, indoor air and workplace air. Applications to headspace of solids and liquids such as different waters, soils, food, etc., are also included. Problems related to calibration in SPME analysis of gaseous matrices are also dealt with. Calibration procedures and apparatus for generation of standard gaseous mixtures are described. Advantages and limitations of SPME based gas chromatographic methods of air organic pollutants are discussed.