Microwave-assisted extraction method for the determination of atrazine and four organophosphorus pesticides in oranges by gas chromatography (GC)

A simple and rapid microwave assisted extraction (MAE) method is presented for the determination of atrazine and four organophosphorus pesticides (parathion-methyl, chlorpyriphos, fenamiphos and methidathion) in orange peel. The experimental variables that affect the MAE method, such as temperature, sample quantity, extraction time, nature and volume of organic solvents, were optimized. The MAE method was optimized using an experimental design. The results suggest that temperature and sample quantity are statistically significant factors. It was concluded that the five pesticides could be efficiently extracted from 1.5–2.5 g of orange peel with 10 mL of hexane/acetone (1?:?1) mixture at 90?°C in 9 min with microwave power set at 50% (475 W). After optimization these factors, recoveries ranged from 93 to 101% with a relative standard deviation ranging from 1 to 3%. The extracts were analyzed by gas chromatography with a nitrogen-phosphorus detector (GC-NPD).     

An efficient and fast microwave-assisted extraction method developed for the simultaneous determination of 18 organochlorine pesticides in sediment

An efficient and fast microwave-assisted extraction (MAE) method followed by gas chromatographic separation with mass spectrometric detection (GC–MS) was developed for the extraction of 18 organochlorine pesticides (OCPs) from sediment. Parameters affecting the MAE procedure such as the type and volume of the extraction solvent, irradiation power, temperature and irradiation time were successfully optimised. Under the optimal conditions, extraction efficiencies in the range of 73.4–119% were obtained with THF–HEX (9:1, v/v) for all OCPs studied. The method was linear over the range of 2.9–5000 ng g^?1 with determination coefficients (r²) higher than 0.992 for all analytes. The limits of detection, LODs (S/N = 3), obtained varied from 1.0 to 2.2 ng g^?1 and limits of quantification, LOQs (S/N = 10) were between 2.9 and 6.8 ng g^?1. The proposed method was successfully applied to the analysis of real sediment samples and acceptable recoveries from 70.1 to 124% with RSDs ≤14.8% were obtained. 10 OCPs were determined below their LOQ and 8 OCPs in the range of 124–2830 ng g^?1. The MAE method was compared with Soxhlet, shake flask and ultrasonic solvent extraction techniques. Thus, the MAE–GC–MS method could efficiently be used for selective extraction and quantification of the target analytes from the complex sediment matrices.     

Microwave-assisted extraction method for the determination of atrazine and four organophosphorus pesticides in oranges by gas chromatography (GC)

A simple and rapid microwave assisted extraction (MAE) method is presented for the determination of atrazine and four organophosphorus pesticides (parathionmethyl, chlorpyriphos, fenamiphos and methidathion) in orange peel. The experimental variables that affect the MAE method, such as temperature, sample quantity, extraction time, nature and volume of organic solvents, were optimized. The MAE method was optimized using an experimental design. The results suggest that temperature and sample quantity are statistically significant factors. It was concluded that the five pesticides could be efficiently extracted from 1.5-2.5 g of orange peel with 10 mL of hexane/acetone (1: 1) mixture at 90 degrees C in 9 min with microwave power set at 50% (475 W). After optimization these factors, recoveries ranged from 93 to 101% with a relative standard deviation ranging from 1 to 3%. The extracts were analyzed by gas chromatography with a nitrogen-phosphorus detector (GC-NPD).     

Microwave assisted extraction of polycyclic aromatic hydrocarbons from atmospheric particulate samples

For several years, microwave assisted extraction (MAE) was applied to extract organic compounds such as polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls, etc., from soils, sediments and standard reference materials. Very few authors applied this methodology for the extraction of PAHs from atmospheric particulate matter. In the present study, MAE of polycyclic aromatic hydrocarbons with hexane/acetone (1:1) from real atmospheric particulate samples was investigated and the effect of microwave energy and irradiation time studied. The yields of extracted compounds obtained by microwave irradiation were compared with those obtained using traditional Soxhlet extraction. MAE was evaluated using spiked real atmospheric particulate samples and two standard reference materials. Analytical determinations of PAHs were carried out by high performance liquid chromatography (HPLC) with ultraviolet and fluorescence detection. The best recoveries were achieved with a microwave energy of 400 W and an irradiation time of 20 min.     

Multi-residue determination of organochlorine pesticides in vegetables in Kirklareli,Turkey by gas chromatography–mass spectrometry

The aim of this study was to investigate the level of organochlorine pesticides use for treatment of tomatoes, eggplants and cucumbers in Kirklareli, Turkey. Eighteen organochlorine pesticides were identified in vegetable samples using microwave or Soxhlet extraction, and results were obtained by gas chromatography–mass spectrometry. The optimized conditions were 1 mL/min for flow rate in the mobile phase, 1 μL for injection volume and 70 V for fragmentation potential. The analytical parameters show that the microwave oven extraction procedure provided the best results when compared to the Soxhlet extraction procedure. Samples were prepared for analysis with hexane?dichlormethane (1: 1, v/v, 40 mL) using a solid-phase extraction method. The limits of detection and quantitation for the eighteen analytes were between 0.02–0.26 and 0.06–0.87 μg/L, respectively, and the relative standard deviations of the migration time ranged from 2.4 to 8.9%. The recoveries of surrogate spiked in vegetable samples ranged from 70 to 116%, respectively. The obtained concentrations of pesticides in all vegetables studied were proved in the range of ND–123 μg/kg. The organochlorine pesticide sum was below the legal limit, except for Endrin and Methoxychlor, which requires a further elucidation of the organochlorine pesticides pollution sources in the region. These studies on accumulation of organochlorine pesticides were necessary for accomplishing a comprehensive ecological risk assessment.     

Evaluation of Extraction Procedures of Organochlorine Pesticides from Natural Waters and Sediments

Abstract

This study aims to evaluate different procedures for the extraction of organochlorine pesticides (OCP's) from natural waters and sediments. In the case of extraction from water, a C18 disk solid-phase extraction method was employed. Recovery experiments in the range of 40 to 200 ng/l with selected organochlorine compounds resulted in average recoveries between 80 and 100%. Four different solvents, hexane, ethyl acetate, acetonitrile and methanol, were tested as eluting agents. Best recoveries were obtained with ethyl acetate and hexane. A comparative study of OCP sediment extraction procedures was performed employing sonication, Soxhlet extraction and shake-flask methods. The capacity of these methods to recover OCP's from a sediment sample fortified at 50 ng/g was evaluated using hexane : acetone (1:1 v/v), hexane: acetone (8:2 v/v), acetonitrile and dichlorometane. The three extraction techniques gave similar results and dichloromethane was the most effective solvent. The optimised methods were applied in the analysis of waters and sediments from the “Aiguamolls de l'Empordà” Nature Park, Girona (Spain).     

Microwave-assisted extraction of OCPs, PCBs and PAHs concentrated by semi-permeable membrane devices (SPMDs)

Microwave-assisted extraction (MAE) has been evaluated as an alternative to dialysis for extraction of some water-borne hydrophobic contaminants sampled by semi-permeable membrane devices (SPMDs). Seven organochlorine pesticides (OCPs), 11 polychlorinated biphenyls (PCBs) and 13 polycyclic aromatic hydrocarbons (PAHs) were accumulated in SPMDs at nanogram levels and extracted with three 3-min irradiation cycles with 33 mL of a solvent mixture hexane–water (10:1,v/v) in each cycle. The developed MAE method gave for all analytes investigated statistically comparable extraction yields with those found by dialysis carried out with a total volume of 250 mL hexane for 48 h at room temperature. The recoveries of all the targeted contaminants were in the range of 65–105% with variation coefficients not exceeding 19%. The applicability of the MAE extraction was tested in field SPMDs samples deployed for 15 days in a sewage-treatment process. Our results show that MAE provides a remarkable reduction of time and solvent volume when used as an extraction method in the analysis of SPMDs.     

Comparison of techniques for the extraction of the anti-cancer drug camptothecin from Nothapodytes foetida

Extraction methods using stirring extraction, Soxhlet extraction, ultrasonic extraction and microwave-assisted extraction (MAE) were evaluated for the percentage extraction of camptothecin (CPT) and 9-methoxycamptothecin (9-Me-CPT) from Nothapodytes foetida. The extracts were analyzed by high performance liquid chromatography (HPLC). Methanol (90%, v/v) extracted high percentage extraction of CPT and 9-Me-CPT compared to ethanol (90%, v/v). The results shows that the percentage extraction of CPT and 9-Me-CPT from N. foetida by MAE was more efficient in short time followed by Soxhlet extraction, ultrasonic and stirring extraction methods. Maximum percentage extraction of CPT (2.67%, w/w) was obtained by MAE technique. MAE has need of 3 min, whereas ultrasonic extraction, Soxhlet extraction and stirring extraction techniques require 30, 120 and 30 min, respectively to leach higher percentage extraction of CPT and 9-Me-CPT. The times taken by the microwave extraction process was 40 times less than the Soxhlet extraction for percentage extraction of alkaloids. The present results show that the extraction efficiency and considerable saving of time by MAE was more competent than the other extraction techniques.     

A cost effective,sensitive, and environmentally friendly sample preparation method for determination of polycyclic aromatic hydrocarbons in solid samples

A simple, cost effective, and yet sensitive sample preparation technique was investigated for determining Polycyclic Aromatic Hydrocarbons (PAHs) in solid samples. The method comprises ultrasonic extraction, Stir Bar Sorptive Extraction (SBSE), and thermal desorption–gas chromatography–mass spectrometry to increase analytical capacity in laboratories. This method required no clean-up, satisfied PAHs recovery, and significantly advances cost performance over conventional extraction methods, such as Soxhlet and Microwave Assisted Extraction (MAE). This study evaluated three operational parameters for ultrasonic extraction: solvent composition, extraction time, and sample load. A standard material, SRM 1649 a (urban dust), was used as the solid sample matrix, and 12 priority PAHs on the US Environmental Protection Agency (US EPA) list were analyzed. Combination of non-polar and polar solvents ameliorated extraction efficiency. Acetone/hexane mixtures of 2:3 and 1:1 (v/v) gave the most satisfactory results: recoveries ranged from 63.3% to 122%. Single composition solvents (methanol, hexane, and dichloromethane) showed fewer recoveries. Comparing 20 min with 60 min sonication, longer sonication diminished extraction efficiencies in general. Furthermore, sample load became a critical factor in certain solvent systems, particularly MeOH. MAE was also compared to the ultrasonic extraction, and results determined that the 20-min ultrasonic extraction using acetone/hexane (2:3, v/v) was as potent as MAE. The SBSE method using 20 mL of 30% alcohol-fortified solution rendered a limit of detection ranging from 1.7 to 32 ng L⁻¹ and a limit of quantitation ranging from 5.8 to 110 ng L⁻¹ for the 16 US EPA PAHs.     

Optimization of microwave-assisted extraction of hydrocarbons in marine sediments: comparison with the Soxhlet extraction method

Microwave energy was applied to extract polycyclic aromatic hydrocarbons (PAHs) and linear aliphatic hydrocarbons (LAHs) from marine sediments. The influence of experimental conditions, such as different extracting solvents and mixtures, microwave power, irradiation time and number of samples extracted per run has been tested using real marine sediment samples; volume of the solvent, sample quantity and matrix effects were also evaluated. The yield of extracted compounds obtained by microwave irradiation was compared with that obtained using the traditional Soxhlet extraction. The best results were achieved with a mixture of acetone and hexane (1:1), and recoveries ranged from 92 to 106%. The extraction time is dependent on the irradiation power and the number of samples extracted per run, so when the irradiation power was set to 500 W, the extraction times varied from 6 min for 1 sample to 18 min for 8 samples. Analytical determinations were carried out by high-performance liquid chromatography (HPLC) with an ultraviolet-visible photodiode-array detector for PAHs and gas chromatography (GC) using a FID detector for LAHs. To test the accuracy of the microwave-assisted extraction (MAE) technique, optimized methodology was applied to the analysis of standard reference material (SRM 1941), obtaining acceptable results.     

Extraction of polycyclic aromatic hydrocarbons and organochlorine pesticides from soils: a comparison between Soxhlet extraction, microwave-assisted extraction and accelerated solvent extraction techniques

The methods of simultaneous extraction of polycyclic aromatic hydrocarbons (PAHs) and organochlorine pesticides (OCPs) from soils using Soxhlet extraction, microwave-assisted extraction (MAE) and accelerated solvent extraction (ASE) were established, and the extraction efficiencies using the three methods were systemically compared from procedural blank, limits of detection and quantification, method recovery and reproducibility, method chromatogram and other factors. In addition, soils with different total organic carbon contents were used to test the extraction efficiencies of the three methods. The results showed that the values obtained in this study were comparable with the values reported by other studies. In some respects such as method recovery and reproducibility, there were no significant differences among the three methods for the extraction of PAHs and OCPs. In some respects such as procedural blank and limits of detection and quantification, there were significant differences among the three methods. Overall, ASE had the best extraction efficiency compared to MAE and Soxhlet extraction, and the extraction efficiencies of MAE and Soxhlet extraction were comparable to each other depending on the property such as TOC content of the studied soil. Considering other factors such as solvent consumption and extraction time, ASE and MAE are preferable to Soxhlet extraction.     

Microwave-assisted extraction of tanshinones from Salvia miltiorrhiza bunge with analysis by high-performance liquid chromatography

A novel microwave-assisted extraction (MAE) method has been developed for the extraction and determination of tanshinones (tanshinone IIA, cryptotanshinone and tanshinone I) from the root of Salvia miltiorrhiza bunge with analysis by HPLC. Various experimental conditions were investigated to optimize the percentage extraction. Under appropriate MAE conditions, such as ethanol concentrations of 95% (v/v), MAE for 2 min, liquid/solid ratio of 10:1 (ml/g), the percentage extraction can reach high in a short time. The percentage extraction (tanshinone IIA: 0.29%; cryptotanshinone: 0.23%; tanshinone I: 0.11%) by MAE was the same or even higher than conventional extraction methods. MAE only needs 2 min, but extraction at room temperature, heat reflux extraction, ultrasonic extraction and Soxhlet extraction need 24 h, 45 min, 75 min and 90 min, respectively. MAE was also available in pilot plant form for larger scale extraction.     

Optimization of microwave-assisted extraction of hydrocarbons in marine sediments: comparison with the Soxhlet extraction method

Microwave energy was applied to extract polycyclic aromatic hydrocarbons (PAHs) and linear aliphatic hydrocarbons (LAHs) from marine sediments. The influence of experimental conditions, such as different extracting solvents and mixtures, microwave power, irradiation time and number of samples extracted per run has been tested using real marine sediment samples; volume of the solvent, sample quantity and matrix effects were also evaluated. The yield of extracted compounds obtained by microwave irradiation was compared with that obtained using the traditional Soxhlet extraction. The best results were achieved with a mixture of acetone and hexane ¶(1?:?1), and recoveries ranged from 92 to 106%. The extraction time is dependent on the irradiation power and the number of samples extracted per run, so when the irradiation power was set to 500 W, the extraction times varied from 6 min for 1 sample to 18 min for 8 samples. Analytical determinations were carried out by high-performance liquid chromatography (HPLC) with an ultraviolet-visible photodiode-array detector for PAHs and gas chromatography (GC) using a FID detector for LAHs. To test the accuracy of the microwave-assisted extraction (MAE) technique, optimized methodology was applied to the analysis of standard reference material (SRM 1941), obtaining acceptable results.     

Influence of the extraction methodology on the analysis of polycyclic aromatic hydrocarbons in pasture vegetation

Pasture vegetation plays an important role in the air-surface exchange and food chain transfer of polycyclic aromatic hydrocarbons (PAHs). Therefore, considerable research has been focused towards measuring PAHs in vegetation using different analytical methods. However, in most cases information on the efficiencies of the different extraction methods employed is missing. This complicates data interpretation and inter-study comparisons. To address this deficiency, the extraction efficiencies of two commonly used pasture vegetation extraction techniques (sonication and soxhlet) and different solvents (hexane, DCM and hexane:acetone [4:1, v/v]) were compared. The completeness of the extraction was investigated using alkaline saponification in methanol. Soxhlet extraction was able to access between 60 and 90% of the total amount of PAHs in the pasture vegetation. Sonication was less efficient, only being able to extract between 10 and 50% of the PAHs. Extraction efficiencies were found to increase with increasing PAH molecular weight. The implications of these findings on data interpretation are discussed.     

Comparison of different extraction techniques for the determination of chlorinated pesticides in animal feed

The performances of Soxhlet extraction, dive-in Soxhlet extraction, microwave-assisted extraction (MAE), accelerated solvent extraction (ASE), fluidized-bed extraction (FBE), and ultrasonic extraction (UE) for the analysis of organochlorine pesticides in animal feed have been investigated. ASE and MAE provided significantly better extraction efficiency than Soxhlet extraction. The concentrations were 126.7 and 114.8%, respectively, of the values obtained by classical Soxhlet extraction, whereas the results from FBE and dive-in Soxhlet were comparable with those from the standard Soxhlet procedure. The reproducibility of FBE was the best, with RSDs ranging from 0.3 to 3.9%. Under the investigated operation conditions UE was not efficient, with the recoveries of target compounds being about 50% less than Soxhlet. Additionally, the performances of Soxhlet, dive-in Soxhlet, MAE, ASE and FBE were validated by determination of the certified reference material BCR-115. The results from the extraction techniques were in good agreement with the certified values.     

Microwave-assisted extraction of trichloroethylene from clay samples

A new method for volatile organic compounds (VOCs) extraction from low-permeability media, such as clay, has been developed and tested using trichloroethylene (TCE) as a model compound. The method is based on microwave-assisted extraction (MAE), which uses microwave energy to heat the extracting solvent and the sample. MAE allows the extraction process to be carried out at elevated temperatures and pressures, which dramatically reduces the time required to complete the process. A custom-made PTFE vessel was used for extraction investigations. TCE analysis was performed using gas chromatography with electron capture detection (GC-ECD). Three different solvents were tested: methanol, 1?:?1 hexane?:?acetone mixture, and 10?:?1 hexane?:?acetone mixture. A comparison of TCE recoveries from clay samples using the new method and the standard methanol extraction method was carried out. The newly developed method and the method currently in use were found to recover similar amounts of TCE. The major advantage of the MAE technique is the very short time needed to obtain complete analyte recovery (6–10?min), which makes it possible to analyse a large number of samples without the need for sample preservation or prolonged storage. Thus, the new method is much more efficient than the existing methods. The technique has a good potential for field application.     

Continuous microwave-assisted extraction coupled on-line with liquid-liquid extraction: determination of aliphatic hydrocarbons in soil and sediments

This paper describes a new extraction method for the determination of aliphatic hydrocarbons (AHs) in soil and sediment samples, using continuous microwave-assisted extraction (MAE) combined with liquid-liquid extraction, for clean-up purposes. Analytical determinations were carried out by gas chromatography coupled with impact ionization mass spectrometry. The influence of the experimental conditions was tested using an agricultural soil spiked with standards (stored at 4 degrees C for 1 month) as reference soil. Maximum extraction efficiencies (80-90%) were achieved using 0.1-1.0g of sample, 60microl of water and 3ml of n-hexane (extractant) and 5min of extraction time; less than 70% of the most volatile hydrocarbons (C(9)-C(12)) were recovered since many evaporated during the drying step of the sample. MAE was compared with a conventional extraction method such as Soxhlet and a good agreement in the results was obtained (average recovery percentage value of 105% by comparing MAE against Soxhlet). Quality parameters such as linear range (0.5-800microg/g), limits of detection (LODs) (0.1-0.2microg/g) and precision (RSD, 4-6%) were determined using spiked soil samples. This method was successfully applied to the analysis of aliphatic hydrocarbons (C(9)-C(27) including pristane and phytane) in contaminated real samples.     

Optimisation and comparison of microwave-assisted extraction and Soxhlet extraction for the determination of polychlorinated biphenyls in soil samples using an experimental design approach

Optimisation of microwave-assisted extraction (MAE) for the extraction of polychlorinated biphenyls (PCBs) from soil samples has been accomplished using an experimental design approach. Variables studied have been: percentage of acetone (v/v) in an acetone:n-hexane mixture, solvent volume, extraction time, microwave power and pressure inside the extraction vessel. Five samples of a certified soil (CRM 481) have been extracted under the optimum conditions of the developed method and the results have been compared to those obtained by Soxhlet extraction. Good recoveries (>95%) have been obtained for all the PCBs studied. All extracts have been analysed by gas chromatography/mass spectrometry (GC/MS) and an optimum determination method for the electron impact mass spectrometric (EIMS) has also been developed.     

An absorbing microwave micro-solid-phase extraction device used in non-polar solvent microwave-assisted extraction for the determination of organophosphorus pesticides

A single-step extraction-cleanup method, including microwave-assisted extraction (MAE) and micro-solid-phase extraction (μ-SPE), was developed for the extraction of ten organophosphorus pesticides in vegetable and fruit samples. Without adding any polar solvent, only one kind of non-polar solvent (hexane) was used as extraction solvent in the whole extraction step. Absorbing microwave μ-SPE device, was prepared by packing activated carbon with microporous polypropylene membrane envelope, and used as not only the sorbent in μ-SPE, but also the microwave absorption medium. Some experimental parameters effecting on extraction efficiency was investigated and optimized. 1.0 g of sample, 8 mL of hexane and three absorbing microwave μ-SPE devices were added in the microwave extraction vessel, the extraction was carried out under 400 W irradiation power at 60 °C for 10 min. The extracts obtained by MAE-μ-SPE were directly analyzed by GC–MS without any clean-up process. The recoveries were in the range of 93.5–104.6%, and the relative standard deviations were lower than 8.7%.     

Determination of 21 organochlorine pesticides in tree leaves using solid-phase extraction clean-up cartridges

A method to determine 21 organochlorine pesticides (OCPs) in tree leaves [chestnut (Castanea sativa), hazel (Corylus avellana), oak (Quercus robur) and walnut tree (Juglans regia)] based on microwave-assisted extraction (MAE) followed by solid-phase extraction (SPE) clean-up is described. After extraction with hexane:acetone (50:50), four different sorbents (Florisil, tandem Florisil + alumina, silica and ENVI-Carb) were assayed for the clean-up step. Pesticides were eluted with 5 mL of hexane:ethyl acetate (80:20) and determined by gas chromatography and electron capture detection (GC-ECD). Carbon was the sorbent, which provided colourless eluates and chromatograms with less interferent compounds. Analytical recoveries obtained were ca. 100% for all the studied pesticides with this sorbent.