Amphiphilic ruthenium dye as an ideal sensitizer in conversion of light to electricity using ionic liquid crystal electrolyte

The optimization of interfacial charge transfer between the dye and the electrolyte is crucial to the design of dye-sensitized solar cells. In this paper, we address the combined use of an ionic liquid crystal electrolyte and amphiphilic ruthenium dyes in dye-sensitized solar cells. The solar cell with an amphiphilic ruthenium dye [Ru(H₂dcbpy)(tdbpy)(NCS)2] (H₂dcbpy = 4,4′-dicarboxy-2,2′-bipyridine, tdbpy = 4,4′-tridecyl-2,2′-bipyridine), exhibited a short-circuit photocurrent density of 9.1 mA/cm², an open-circuit voltage of 665 mV and a fill factor of 0.58, corresponding to an overall conversion efficiency of 3.51%. We find that increasing dye alkyl chain length to octadecyl from tridecyl results in lower short-circuit photocurrent density and open-circuit voltage, and the suitable dyes for ionic liquid crystal electrolyte differed completely from those used in liquid and ionic liquid electrolyte cells.     

Electrochemical properties of liquid electrolyte added quasi-solid state TiO2 dye-sensitized solar cells

In this study a process has been introduced to replace traditional liquid or solid electrolyte coatings on dye-sensitized photoelectrode in solar cells. This process has more efficient diffusion of electrolyte, hence higher sensitivity. Better interfacial contact between polymer electrolyte and TiO₂ photoelectrode had improved electrochemical response and ionic conductivity of cell. Conductivity of this electrode was 9.33 × 10⁻³ S cm⁻¹ (at room temperature), which is much higher than the using traditional process for addition of electrolytes. It has 0.68 V open-circuit voltage and 3.19 mA cm⁻² short-circuit current density. Energy conversion efficiency of this cell was about 37% higher than the cell developed with traditional processes under constant light intensity (45 mW cm⁻²).     

Photovoltaic performance of dye-sensitized solar cells assembled by in-situ chemical cross-linking

Quasi-solid state dye-sensitized solar cells (DSSCs) were assembled by in-situ chemical cross-linking of a gel electrolyte precursor containing liquid electrolyte. The DSSCs assembled with this cross-linked gel polymer electrolyte showed higher open circuit voltage and lower short-circuit photocurrent density than those of DSSCs with liquid electrolyte. Addition of SiO₂ nanoparticles into the cross-linked gel polymer electrolyte significantly improved the photovoltaic performance and long-term stability of the DSSCs. The optimized quasi-solid state DSSC showed high conversion efficiency, 6.2% at 100 mW cm^?2 with good durability.     

Quasi-solid-state dye-sensitized solar cells assembled with polymeric ionic liquid and poly(3,4-ethylenedioxythiophene) counter electrode

Poly(3,4-ethylenedioxythiophene) nanofibers (PEDOT-NF) with high catalytic activity were synthesized and employed as a counter electrode in dye-sensitized solar cells (DSSCs). A polymeric ionic liquid (PIL) was used as a gelling agent and an iodide source for making a highly conductive gel polymer electrolyte. A quasi-solid-state DSSC assembled with this PIL-based gel polymer electrolyte and PEDOT-NF counter electrode exhibited high conversion efficiency of 8.12% at 100 mW cm^− 2.     

Organic dyes with a novel anchoring group for dye-sensitized solar cell applications

Two novel trialkylsilyl-containing organic sensitizers (JK-53 and JK-54) have been designed and synthesized. Nanocrystalline TiO₂–silica-based dye-sensitized solar cells (DSSCs) were fabricated using these dyes. Under standard global AM 1.5 solar conditions, the JK-53-sensitized cell gave a short-circuit photocurrent density (J_sc) of 6.37 mA cm^?2, an open-circuit voltage (V_oc) of 0.70 V, and a fill factor of 0.74. These values correspond to an overall conversion efficiency (η) of 3.31%. By comparison, the JK-54-sensitized cell resulted in a J_sc of 7.52 mA cm^?2, a V_oc of 0.71 V, and a fill factor of 0.75. These values give an overall conversion efficiency of 4.01%.     

Synthesis and photovoltaic properties of organic sensitizers containing electron-deficient and electron-rich fused thiophene for dye-sensitized solar cells

Diverse fused thiophenes with electron-rich and electron-deficient blocks have been synthesized and employed as the π-conjugated spacers of organic dyes for the dye-sensitized solar cells (DSSCs). The effects of these fused thiophenes were investigated by their absorption spectra, electrochemical and photovoltaic properties. For a typical device a maximum power conversion efficiency of 6.11% was obtained under simulated AM 1.5 irradiation (100 mW cm^?2): a short-circuit current (J_SC) of 14.47 mA cm^?2, an open-circuit voltage (V_OC) of 670 mV, and a fill factor (FF) of 0.63.     

In situ growth of polymer electrolytes on lithium ion electrode surfaces

Polyacrylonitrile (PAN) films were grown on glassy carbon, nickel foam and MnO₂ substrates by cathodic electropolymerisation of acrylonitrile in acetonitrile with tetrabutylammonium perchlorate (TBAP) as the supporting electrolyte. The electronic barrier properties of the films were confirmed by impedance spectroscopy of carbon |PAN| Hg cells while the ionic resistance of the films varied from 200 kΩ cm² in the dry state to 1.4 Ω cm² when plasticised with 1 M LiPF₆ in propylene carbonate. A galvanic cell was prepared by successive electrodepositions of MnO₂ and PAN on a carbon substrate, using liquid lithium amalgam as the top contact. The cell showed a stable open circuit potential and behaved normally under the galvanostatic intermittent titration technique (GITT).     

Highly efficient quasi-solid-state quantum-dot-sensitized solar cell based on hydrogel electrolytes

Chemically crosslinked polyacrylamide-based hydrogel has been first used as the polymer matrix to prepare quasi-solid-state polysulfide electrolyte for CdS/CdSe co-sensitized solar cells (QDSCs). The room temperature ionic conductivity of the gel electrolyte reaches 0.093 S·cm^?1. QDSCs based on this quasi-solid-state electrolyte can present up to 4.0% of light-to-electricity conversion efficiency. Meanwhile, the interfacial recombination at TiO₂/electrolyte interface of the cell is also investigated by Electrochemical Impedance Spectroscopy (EIS).     

Facile synthesis of thick ordered mesoporous TiO2 film for dye-sensitized solar cell use

Crack-free thick ordered mesoporous TiO₂ films with excellent optical quality have been synthesized by combination of “Doctor Blade” technique and a two-step evaporation induced self-assembly (EISA) method. By employing the as-synthesized mesoporous film with the thickness of 7 μm as the photoanode in dye-sensitized solar cell (DSC), a solar conversion efficiency of 6.53% has been obtained at 30 mW cm⁻² light intensity.     

Spray coated multi-wall carbon nanotube counter electrode for tri-iodide (I3-) reduction in dye-sensitized solar cells

Spray coated multi-wall carbon nanotube (CNT) film on fluorine-doped tin oxide glass substrate has been investigated as a counter electrode for tri-iodide reduction in dye-sensitized solar cells. The photovoltaic parameters, in particular, the fill factor shows a strong dependency on the spraying time of multi-wall CNTs. Under one sun illumination (100 mW cm⁻², AM 1.5 G), the device shows a maximum energy conversion efficiency of 7.59%. Electrochemical impedance spectroscopy analysis reveals a decrease in the charge transfer resistance of multi-wall CNT counter electrode with increase of spraying time; leads to an improvement in the photovoltaic parameters.     

Synthesis of triphenylamine-based thiophene-(N-aryl)pyrrole-thiophene dyes for dye-sensitized solar cell applications

Two new triphenylamine-based metal-free organic dyes (TPTDYE-1 and TPTDYE-2) containing 1-(2,6-diisopropylphenyl)-2,5-di(2-thienyl)pyrrole as a new π-conjugated chromophore were synthesized for dye-sensitized solar cell (DSSC) applications. TPTDYE-1 containing three donor groups around the acceptor group was found to show relatively narrow absorption band from 300 nm to 470 nm while TPTDYE-2 having extended π–π delocalization between the donor and acceptor group showed broad absorption band from 300 nm to 550 nm. The electrochemical studies indicate that the HOMO–LUMO energy gap of TPTDYE-1 is considerably wider than that of TPTDYE-2. The dye-sensitized solar cell performance of each dye was investigated, and the TPTDYE-2-sensitized cell was found to show a maximum monochromatic incident photon-to-current conversion efficiency (IPCE) of 75%, a short-circuit photocurrent density (J_sc) of 13.50 mA/cm², an open-circuit voltage (V_oc) of 0.72 V, and a fill factor (FF) of 0.69, corresponding to an overall conversion efficiency of 6.71% under simulated AM 1.5 irradiation (100 mW/cm²). Under the same condition the TPTDYE-1-sensitized cell showed the same IPCE value of 75% with a promising conversion efficiency of 6.00%, a J_sc of 11.11 mA/cm², a V_oc of 0.76 V, and a FF of 0.71.     

Li2SO4-polyacrylamide polymer electrolytes for 2.0 V solid symmetric supercapacitors

A neutral polymer electrolyte comprised of lithium sulfate (Li₂SO₄) and polyacrylamide (PAM) was developed. The Li₂SO₄-PAM electrolyte film shows an ionic conductivity up to 10 mS cm^− 1 in 45%RH conditions. Solid double layer capacitors were demonstrated using CNT-graphite electrodes and Li₂SO₄-PAM solid electrolytes. The voltage window of the solid cell was about 2.0 V, identical to that of a Li₂SO₄ liquid cell used as baseline. The demonstrated voltage window is significantly larger than that reported for proton- or hydroxyl-conducting electrolytes, suggesting that the Li₂SO₄-PAM electrolyte is a promising system for high energy density supercapacitors. The solid device also demonstrated excellent rate capability (up to 5 V s^− 1) and good cycle life (beyond 10,000 charge/discharge cycles).     

High-surface-area microporous carbon as the efficient photocathode of dye-sensitized solar cells

This paper reports on the application of cornstalks-derived high-surface-area microporous carbon (MC) as the efficient photocathode of dye-sensitized solar cells (DSCs). The photocathode, which contains MC active material, Vulcan XC–72 carbon black conductive agent, and TiO₂ binder, was obtained by a doctor blade method. Electronic impedance spectroscopy (EIS) of the MC film uniformly coated on fluorine doped SnO₂ (FTO) glass displayed a low charge-transfer resistance of 1.32 Ω cm². Cyclic voltammetry (CV) analysis of the as-prepared MC film exhibited excellent catalytic activity for I₃^?/I^? redox reactions. The DSCs assembled with the MC film photocathode presented a short-circuit photocurrent density (J_sc) of 14.8 mA cm^?2, an open-circuit photovoltage (V_oc) of 798 mV, and a fill factor (FF) of 62.3%, corresponding to an overall conversion efficiency of 7.36% under AM 1.5 irradiation (100 mW cm^?2), which is comparable to that of DSCs with Pt photocathode obtained by conventional thermal decomposition.     

Li/LiFePO4 batteries with room temperature ionic liquid as electrolyte

Room temperature ionic liquid (RTIL) was prepared on basis of N-methyl-N-butylpiperidinium bis(trifluoromethanesulfonyl)imide (PP₁₄TFSI), which showed a wide electrochemical window (?0.1–5.2 V vs. Li⁺/Li) and is theoretically feasible as an electrolyte for batteries with metallic Li as anodes. The addition of vinylene carbonate (VC) improved the compatibility of PP₁₄TFSI-based electrolyte towards lithium anodes and enhanced the formation of solid electrolyte interphase film to protect lithium anodes from corrosion. Accordingly, Li/LiFePO₄ cells initially delivered a discharge capacity of about 127 mAh g^?1 at a current density of 17 mA g^?1 in the ionic liquid with the addition of VC and showed better cyclability than in the neat ionic liquid. Electrochemical impedance spectroscopy disclosed that the addition of VC enhanced Li-ion diffusion and depressed interfacial resistance significantly.     

Molybdenum electrodes for hydrogen production by water electrolysis using ionic liquid electrolytes

The hydrogen production by water electrolysis was tested with different electrocatalysts (molybdenum, nickel, iron alloys containing chromium, manganese and nickel) using aqueous solutions of ionic liquid (IL) like 1-butyl-3-methylimidazolium tetrafluoroborate (BMI.BF₄). The hydrogen evolution reaction (HER) was performed at room temperature in a potential of −1.7 V (PtQRE). A Hoffman cell apparatus was used to water electrolysis with current density values, j, between 14.6 mA cm⁻² (for Ni electrode) and 77.5 mA cm⁻² (for Mo electrode). The system efficiency was very high for all electrocatalysts tested, between 97.0% and 99.2%. The energy activation values of HER was determined in an aqueous solution of BMI.BF₄ 10 vol.%, using platinum (23.40 kJ mol⁻¹) and Mo (9.22 kJ mol⁻¹) as electrocatalysts. The results show that the hydrogen production in IL electrolyte can be carried out with cheap material at room temperature, which makes this method economically attractive.     

Efficient passivation of SnO2 nano crystallites by Indoline D-149 via dual chelation

For the first time in SnO₂ based dye solar cells, here we report, efficiency exceeding 3% of the cells consisting with Indoline D-149 dye with unmodified SnO₂ nano-crystallites. The cells sensitized with metal free D-149 dye together with liquid electrolyte comprising with 0.5 M tetrapropyl ammonium iodide and 0.05 M iodine in a mixture of acetonitrile and ethylene carbonate (1:4 by volume) delivered a short circuit current density of 10.4 mA cm^?2 with an open circuit voltage of 530 mV under the illumination of 100 mW cm^?2 (AM1.5) having an efficiency of 3.1%. As evident from the FTIR measurement, strong surface passivation of recombination centers of SnO₂ crystallites due to the dual mode of attachment of dye molecules to the surface of SnO₂ via both COOH and S–O direct bond might be the possible reason for this enhancement in these SnO₂ based cells.     

Electrical,optical and photoelectrochemical studies on a solid PEO-polymer electrolyte doped with low viscosity ionic liquid

Solid polymer electrolyte (PEO:KI:I₂) membranes doped with low viscosity (34 cP at 25 °C) ionic liquid EMImTFSI (1-ethyl 3-methylimidazolium bis(trifluoromethylsulfonyl)imide) showing plasticizing effect as well as improved dye sensitized solar cell efficiency have been reported first time. Apart from ionic conductivity enhancement due to large number of free charge carriers provided by ionic liquid (IL) it assist in reducing cystallinity of polymer electrolyte matrix which was confirmed by polarized optical microscopy (POM). Cyclic voltammetry was carried out to study the reactions of iodide, iodine and IL in polymer electrolyte matrix.     

Outstanding room-temperature capacitance of biomass-derived microporous carbons in ionic liquid electrolyte

A remarkable capacitance of 180 F·g^− 1 (at 5 mV·s^− 1) in solvent-free room-temperature ionic liquid electrolyte, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, was achieved in symmetric supercapacitors using microporous carbons with a specific surface area of ca. 2000 m²·g^− 1 calculated from gas sorption by the 2D-NLDFT method. The efficient capacitive charge storage was ascribed to textural properties: unlike most activated carbons, high specific surface area was made accessible to the bulky ions of the ionic liquid electrolyte thanks to micropores (1–2 nm) enabled by fine-tuning chemical activation. From the industrial perspective, a high volumetric capacitance of ca. 80 F·cm^− 3 was reached in neat ionic liquid due to the absence of mesopores. The use of microporous carbons from biomass waste represents an important advantage for large-scale production of high energy density supercapacitors.     

Development of micro-tubular SOFCs with an improved performance via nano-Ag impregnation for intermediate temperature operation

Micro-tubular solid-oxide fuel cell consisting of a 10-μm thick (ZrO₂)_0.89(Sc₂O₃)_0.1(CeO₂)_0.01 (ScSZ) electrolyte on a support NiO/(ScSZ) anode (1.8 mm diameter, 200 μm wall thickness) with a Ce_0.8Gd_0.2O_1.9 (GDC) buffer-layer and a La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ (LSCF)/GDC functional cathode has been developed for intermediate temperature operation. The functional cathode was in situ formed by impregnating the well-dispersed nano-Ag particles into the porous LSCF/GDC layer using a citrate method. The cells yielded maximum power densities of 1.06 W cm⁻² (1.43 A cm⁻², 0.74 V), 0.98 W cm⁻² (1.78 A cm⁻², 0.55 V) and 0.49 W cm⁻² (1.44 A cm⁻², 0.34 V), at 650, 600 and 550 °C, respectively.     

LiTFSI as a plastic salt in the quasi-solid state polymer electrolyte for dye-sensitized solar cells

Ionic conductivity and the type of ions are important for the composite polymer electrolyte (CPE) of the dye-sensitized solar cells (DSSCs). Lithium bis(trifluoromethane sulphone)imide (LiTFSI for short) which is easy to dissociate, is added in the composite polymer electrolyte(CPE) as a plasticizer. The LiTFSI acts differently from the conventional LiClO₄. LiTFSI changes the conformation of the polymer chain and shows higher ionic conductivity than LiClO₄. That contributes to the improvement of the short current density of the DSSC. Furthermore, the DSSCs with LiTFSI modification show higher photovoltage than the LiClO₄. The anions of TFSI^? prohibit the interface recombination more effectively compared with the LiClO₄ as the electrochemical impedance spectroscopy indicated. With the LiTFSI modified electrolyte, the performances of the DSSCs under 1 Sun, AM1.5 are improved and reaches the highest of 4.82% at the LiTFSI:LiI = 0.116:1, much better than the original DSSC(3.6%) and the LiClO₄ modified CPE electrolyte DSSC(4.32%).