Ionic liquid functionalized polylactide by cationic polymerization: Synthesis and stabilization of carbon nanotube suspensions

Medium molecular weight poly(L ,L ‐lactide)s (PLA) containing at one chain end ionic group derived from imidazolium ionic liquid (IL) were synthesized by cationic polymerization using hydroxylated IL as initiator. matrix assisted laser desorption/ionization time‐of‐flight analysis confirmed the structure of products (PLA‐IL). Carbon nanotubes (CNT) were dispersed in solution of PLA‐IL in 1,4‐dioxane and significant improvement of stability of suspension was observed by measurements of suspension absorbance. Similar effect was, however, observed also for solutions of PLA which did not contain terminal IL group. CNT samples treated with PLA‐IL and PLA were isolated, thoroughly washed with 1,4‐dioxane and stability of suspensions was again measured. Sample treated with PLA after washing behave similarly to untreated CNT. Stability of suspension of CNT treated with PLA‐IL after washing was considerably higher than that of untreated CNT and the presence of polymer bound to CNT was clearly detectable in scanning electron microscopy images. Results indicate that there is indeed an interaction between end‐group derived from IL and CNT surface as postulated earlier but to observe solely this effect an excess of polymer should be removed, otherwise factors such as increase of viscosity of solution or weak interactions of PLA ester groups with CNT may obscure results. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Block and random copolymerization of ε‐caprolactone,L‐, and rac‐lactide using titanium complex derived from aminodiol ligand

A series of di‐ and triblock copolymers [poly(L ‐lactide‐b‐ε‐caprolactone), poly(D,L ‐lactide‐b‐ε‐caprolactone), poly(ε‐caprolactone‐b‐L ‐lactide), and poly(ε‐caprolactone‐b‐L ‐lactide‐b‐ε‐caprolactone)] have been synthesized successfully by sequential ring‐opening polymerization of ε‐caprolactone (ε‐CL) and lactide (LA) either by initiating PCL block growth with living PLA chain end or vice versa using titanium complexes supported by aminodiol ligands as initiators. Poly(trimethylene carbonate‐b‐ε‐caprolactone) was also prepared. A series of random copolymers with different comonomer composition were also synthesized in solution and bulk of ε‐CL and D,L ‐lactide. The chemical composition and microstructure of the copolymers suggest a random distribution with short average sequence length of both the LA and ε‐CL. Transesterification reactions played a key role in the redistribution of monomer sequence and the chain microstructures. Differential scanning calorimetry analysis of the copolymer also evidenced the random structure of the copolymer with a unique T_g. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of poly(ethylene glycol)/polypeptide/poly(D,L‐lactide) copolymers and their nanoparticles

Core‐shell structured nanoparticles of poly(ethylene glycol) (PEG)/polypeptide/poly(D ,L ‐lactide) (PLA) copolymers were prepared and their properties were investigated. The copolymers had a poly(L ‐serine) or poly(L ‐phenylalanine) block as a linker between a hydrophilic PEG and a hydrophobic PLA unit. They formed core‐shell structured nanoparticles, where the polypeptide block resided at the interface between a hydrophilic PEG shell and a hydrophobic PLA core. In the synthesis, poly(ethylene glycol)‐b‐poly(L ‐serine) (PEG‐PSER) was prepared by ring opening polymerization of N‐carboxyanhydride of O‐(tert‐butyl)‐L ‐serine and subsequent removal of tert‐butyl groups. Poly(ethylene glycol)‐b‐poly(L ‐phenylalanine) (PEG‐PPA) was obtained by ring opening polymerization of N‐carboxyanhydride of L ‐phenylalanine. Methoxy‐poly(ethylene glycol)‐amine with a MW of 5000 was used as an initiator for both polymerizations. The polymerization of D ,L ‐lactide by initiation with PEG‐PSER and PEG‐PPA produced a comb‐like copolymer, poly(ethylene glycol)‐b‐[poly(L ‐serine)‐g‐poly(D ,L ‐lactide)] (PEG‐PSER‐PLA) and a linear copolymer, poly(ethylene glycol)‐b‐poly(L ‐phenylalanine)‐b‐poly(D ,L ‐lactide) (PEG‐PPA‐PLA), respectively. The nanoparticles obtained from PEG‐PPA‐PLA showed a negative zeta potential value of ?16.6 mV, while those of PEG‐PSER‐PLA exhibited a positive value of about 19.3 mV. In pH 7.0 phosphate buffer solution at 36 °C, the nanoparticles of PEG/polypeptide/PLA copolymers showed much better stability than those of a linear PEG‐PLA copolymer having a comparable molecular weight. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Structure of poly(L‐lactic acid)s prepared by the dehydropolycondensation of L‐lactic acid with organotin catalysts

The synthesis of low‐molecular‐weight (weight‐average molecular weight < 45,000 g/mol) lactic acid polymers through the dehydropolycondensation of L ‐lactic acid was investigated. Polymerizations were carried out in solution with solvents (xylene, mesitylene, and decalin), without a solvent using different Lewis acid catalysts (tetraphenyl tin and tetra‐n‐butyldichlorodistannoxane), and at three different polymerization temperatures (143, 165, and 190 °C). The products were characterized with differential scanning calorimetry, size exclusion chromatography, vapor pressure osmometry, ¹³C NMR, and matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF). The resulting polymers contained less than 1 mol % lactide, as shown by NMR. The number‐average molecular weights were calculated from the ratio of the area peaks of ester carbonyl and carboxylic acid end groups via ¹³C NMR. The stereosequences were analyzed by ¹³C NMR spectroscopy on the basis of triad effects. Tetraphenyl tin was an effective transesterification catalyst, and the randomization of the stereosequence at 190 °C was observed. In contrast, the distannoxane catalyst caused comparatively less transesterification reaction, and the randomization of the stereosequences was slow even at 190 °C. The L ‐lactic acid and D ‐lactic acid isomers were added to the polymer chain in a small, blocky fashion. The MALDI‐TOF spectra of poly(L ‐lactic acid) (PLA) chains doped with Na⁺ and K⁺ cations showed that the PLA chains had the expected end groups. The MALDI‐TOF analysis also enabled the simultaneous detection of the cyclic oligomers of PLA present in these samples, and this led to the full structural characterization of the molecular species in PLA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2164–2177, 2005     

Dendritic homopolymers and block copolymers: Tuning the morphology and properties

The synthesis and characterization of dendritic homopolymers and block copolymers of ?‐caprolactone and lactide (L ‐lactide and racemic lactide) were performed with multifunctional initiators in combination with living polymerization and the selective placement of branching junctures in a divergent growth strategy. A hexahydroxy‐functional 2,2‐bis(hydroxymethyl) propionic acid derivative was used as an initiator for the stannous‐2‐ethylhexanoate‐catalyzed living ring‐opening polymerization of ?‐caprolactone, L ‐lactide, and racemic L ,D ‐lactide. Branching junctions at the chain ends were introduced with benzylidene‐protected 2,2‐bis(hydroxymethyl) propionic acid. Subsequent generations were then polymerized, after deprotection, from these star‐shaped macroinitiators. Successive chain end capping and initiation produced three generations of polymers with molecular weights in excess of 130,000 g/mol and narrow polydispersities (<1.20). It was possible to prepare diblock and triblock copolymers with phase‐separated morphologies, and with L ‐lactide or D ,L ‐lactide, semicrystalline and amorphous morphologies were demonstrated. The polymers were characterized by ¹H NMR, ¹³C NMR, size exclusion chromatography, and differential scanning calorimetry. The compositions of the block copolymers and the conformational structures of the optically active polymers were also confirmed by optical rotation measurements. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1174–1188, 2004     

Synthesis of unimolecular reversed micelle consisting of a poly(L‐lactide) shell and hyperbranched D‐mannan core

A novel biodegradable unimolecular reversed micelle consisting of a poly(L ‐lactide) (PLA) shell and a hyperbranched D ‐mannan (HBM) core, that is, a chestnut‐shaped polymer (PLA–HBM), was synthesized by the polymerization of L ‐lactide on HBM with 4‐(dimethylamino)pyridine (DMAP) as the catalyst. The obtained polymers were soluble in dimethyl sulfoxide, tetrahydrofuran, and chloroform but insoluble in H₂O. The molecular weights of the PLA chain on PLA–HBM tended to increase with increasing polymerization time. The number of PLA chains on PLA–HBM could be controlled by the ratio of DMAP to the sugar unit in HBM. The obtained copolymer, PLA–HBM, acted as a unimolecular reversed micelle with an encapsulation ability toward the hydrophilic molecule. In addition, the entrapped hydrophilic molecules were slowly released from the core of PLA–HBM, and the release rate was accelerated by the breaking of the PLA chains of the shell when proteinase K as a hydrolase of PLA was used. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 406–413, 2006     

Molecular design of outermost surface functionalized thermoresponsive polymeric micelles with biodegradable cores

We prepared well‐defined diblock copolymers of thermoresponsive poly(N‐isopropylacrylamide‐co‐N,N‐dimethylacrylamide) blocks and biodegradable poly(D ,L ‐lactide) blocks by combination of reversible addition‐fragmentation chain transfer radical (RAFT) polymerization and ring‐opening polymerization. α‐Hydroxyl, ω‐dithiobenzoate thermoresponsive polymers were synthesized by RAFT polymerization using hydroxyl RAFT agents. Biodegradable blocks were prepared by ring‐opening polymerization of D ,L ‐lactide initiated by α‐hydroxyl groups of thermoresponsive polymers, which inhibit the thermal decomposition of ω‐dithioester groups. Terminal dithiobenzoate (DTBz) groups of thermoresponsive blocks were easily reduced to thiol groups and reacted with maleimide (Mal). In aqueous media, diblock copolymer products formed surface‐functionalized thermoresponsive micelles. These polymeric micelles had a low critical micelle concentration of 22 μg/L. In thermoresponsive studies of the micelles, hydrophobic DTBz‐surface micelles demonstrated a significant shift in lower critical solution temperature (LCST) to a lower temperature of 30.7 °C than that for Mal‐surface micelles (40.0 °C). In addition, micellar LCST was controlled by changing bulk mixture ratios of respective heterogeneous end‐functional diblock copolymers. Micellar disruption at acidic condition (pH 5.0) was completed within 5 days due to hydrolytic degradation of PLA cores, regardless of showing a slow disruption rate at physiological condition. Furthermore, we successfully improved water‐solubility of hydrophobic drug, paclitaxel by incorporating into the micellar cores. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7127–7137, 2008     

Block copolymers via macromercaptan initiated ring opening polymerization

Poly(styrene) macromercaptanes (M_n = 1900, 3600, and 6100 g mol^?1, PDI ≈ 1.2) derived from thiocarbonyl thio capped polymers prepared via reversible addition fragmentation chain transfer polymerization were employed to initiate the ring opening polymerization (ROP) of D ,L ‐lactide under conditions of organo‐catalyis employing 4,4‐dimethylaminopyridine. Poly(styrene)‐block‐poly(lactide) polymers of number average molecular weights up to 25,000 g mol^?1 (PDI ≈ 1.2 to 1.6) were obtained and characterized via multiple detection size exclusion chromatography (SEC) using refractive index as well as UV detection. In addition, diffusion ordered nuclear magnetic resonance and liquid chromatography at critical conditions (of both polystyrene as well as poly(lactide) were employed to assess the copolymers' structure. Furthermore, it was demonstrated that polyethylenes capped with a thiol moiety can also be readily chain extended in a ROP employing D ,L ‐lactide, evidenced via NMR and high temperature SEC. This study indicates that the direct use of macromercaptantes is indeed a methodology to switch from a radical to a ROP process. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of temperature‐ and pH‐sensitive hydrogels based on poly(2‐ethyl‐2‐oxazoline) and poly(D,L‐lactide)

A novel series of temperature‐ and pH‐sensitive hydrogels based on poly(2‐ethyl‐2‐oxazoline) and three‐arm poly(D,L ‐lactide) were synthesized via photocopolymerization. For the creation of polymeric networks, two types of macromers terminated with methacrylate groups were prepared: poly(2‐ethyl‐2‐oxazoline) dimethacrylate and three‐arm poly(D,L ‐lactide) trimethacrylate. The chemical structures were analyzed with ¹H NMR and Fourier transform infrared techniques. The thermal behaviors, morphologies, and swelling properties were measured for the characterization of the polymeric networks. All the poly(2‐ethyl‐2‐oxazoline)/three‐arm poly(D,L ‐lactide)hydrogels provided high water retention capacity and exhibited reversible swelling–shrinking behavior in response to temperature and pH variations. The hydrogels with higher poly(2‐ethyl‐2‐oxazoline) dimethacrylate contents were more effective in raising the swelling ratio and temperature and pH sensitivity. However, higher contents of three‐arm poly(D,L ‐lactide) trimethacrylate produced larger particles and pore sizes in the hydrogels. This study effectively proves that this unique combination of water swellability and biodegradability provides hydrogels with a much wider range of applications in biomedical fields. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1112–1121, 2002     

Highly biodegradable copolymers composed of chiral depsipeptide and L‐lactide units with favorable physical properties

Syntheses of copolymers composed of optically active depsipeptides (3,6‐dimethyl‐2,5‐morphorinedione) and L ‐lactide—poly(L ‐3,L ‐6‐dimethyl‐2,5‐morphorinedione‐co‐L ‐lactide), poly(L ‐3,DL ‐6‐dimethyl‐2,5‐morphorinedione‐co‐L ‐lactide), and poly(L ‐3,D ‐6‐dimethyl‐2,5‐morphorinedione‐co‐L ‐lactide)—were examined in an effort to improve the biodegradability and physical properties of homopoly(L ‐lactide). In degradation tests, the copolymers composed of 3,6‐dimethyl‐2,5‐morphorinedione and lactide in the ratios 10/90 to 13/87 exhibited high biodegradability toward proteinase K, whereas a homopolymer, poly(L ‐lactide), exhibited very poor biodegradability (only 50% after 200 h). These polymers composed of 3,6‐dimethyl‐2,5‐morphorinedione/L ‐lactide in 11/89 to 13/87 ratios also degrades rapidly after being in compost for 30 days. The resulting copolymers, however, showed relatively low elongation properties. Therefore, ternary copolymerizations of L ‐3,DL ‐6‐dimethyl‐2,5‐morphorinedione, ?‐caprolactone, and L ‐lactide were explored in an effort to improve their mechanical properties, especially the elongation, and sufficient results were obtained with an approximate ratio of 3/11/86. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 302–316, 2002     

Preparation and characterization of poly(2‐methacryloyloxyethyl phosphorylcholine)‐block‐poly(D,L‐lactide) polymer nanoparticles

A poly(D,L ‐lactide)–bromine macroinitiator was synthesized for use in the preparation of a novel biocompatible polymer. This amphiphilic diblock copolymer consisted of biodegradable poly(D,L ‐lactide) and 2‐methacryloyloxyethyl phosphorylcholine and was formed by atom transfer radical polymerization. Polymeric nanoparticles were prepared by a dialysis process in a select solvent. The shape and structure of the polymeric nanoparticles were determined by ¹H NMR, atomic force microscopy, and ζ‐potential measurements. The results of cytotoxicity tests showed the good cytocompatibility of the lipid‐like diblock copolymer poly(2‐methacryloyloxyethyl phosphorylcholine)‐block‐poly(D,L ‐lactide). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 688–698, 2007     

Synthesis of poly(lactide‐ran‐MOHEL) and its biodegradation with proteinase K

Homopoly(L ‐lactide) and homopoly(D,L ‐lactide) were almost inert for biodegradation with tricine buffer or normal enzymes such as bromelain, pronase, and cholesterol esterase but biodegradable with proteinase K. Significantly enhanced biodegradation was observed when an optically active (R)‐ or (S)‐3‐methyl‐4‐oxa‐6‐hexanolide (MOHEL) unit was introduced into poly(L ‐lactide) [poly(L ‐LA)] or poly(D,L ‐lactide) [poly(D,L ‐LA)] sequences. Poly[L ‐LA‐ran‐(R)‐MOHEL] in molar ratios of 86/14 to 43/57 showed good biodegradability that was independent of crystallinity. The biodegradation of polymers with proteinase K increased in the following order: poly[D,L ‐LA‐ran‐(R)‐MOHEL] > poly[L ‐LA‐ran‐(R)‐MOHEL] > poly[D,L ‐LA‐ran‐(S)‐MOHEL] > poly[L ‐LA‐ran‐(S)‐MOHEL] > poly(R)‐MOHEL > poly(D,L ‐LA). The number‐average molecular weight, molecular weight distribution, glass‐transition temperature, and melting temperature did not change before and after the biodegradation of poly[L ‐LA‐ran‐(R)‐MOHEL], indicating that the degradation occurred from the polymer surface. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1374–1381, 2001     

Microwave‐assisted synthesis and characterization of biodegradable block copolyesters based on poly(3‐hydroxyalkanoate)s and poly(D,L‐lactide)

Microwave (MW)‐assisted ring‐opening polymerization (ROP) provides a rapid and straightforward method for engineering a wide array of well‐defined poly(3‐hydroxyalkanoate)‐b‐poly(D,L ‐lactide) (PHA‐b‐PLA) diblock copolymers. On MW irradiation, the bulk ROP of D,L ‐lactide (LA) could be efficiently triggered by a series of monohydroxylated PHA‐based macroinitiators previously produced via acid‐catalyzed methanolysis of corresponding native PHAs, thus affording diblock copolyesters with tunable compositions. The dependence of LA polymerization on temperature, macroinitiator structure, irradiation time, and [LA]₀/[PHA]₀ molar ratio was carefully investigated. It turned out that initiator efficiency values close to 1 associated with conversions ranging from 50 to 85% were obtained only after 5 min at 115 °C. A kinetic investigation of the MW‐assisted ROP of LA gave evidence of its “living”/controlled character under the experimental conditions selected. Structural analyses and thermal properties of biodegradable diblock copolyesters were also performed. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation of main‐chain imidazolium‐functionalized amphiphilic block copolymers through combination of condensation polymerization and nitroxide‐mediated free radical polymerization and their micelle study

Main‐chain imidazolium‐functionalized amphiphilic block copolymers (PIL‐b‐PS) consisting of polyionic liquid (PIL) and polystyrene (PS) blocks have been first synthesized by condensation polymerization combined with nitroxide‐mediated free radical polymerization (NMP). The di‐functional imidazolium‐based ionic liquid (IL) having both hydroxyl and ester end groups was synthesized through Michael addition between imidazole and methylacrylate (MA) and further quaternization by 2‐chloroethanol. The HTEMPO (4‐hydroxy‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy) terminated polyionic liquid (HTEMPO‐PIL) as the hydrophilic block was prepared by condensation polymerization of di‐functional imidazolium IL and HTEMPO at a certain ratio. The hydrophobic PS block was synthesized by controlled radical polymerization of styrene using HTEMPO‐PIL through NMP, resulting PIL‐b‐PS block copolymers. The structure of block copolymers obtained has been characterized and verified by FTIR, ¹H NMR, and size exclusion chromatography analyses. In addition, the morphology and size of the micelles formed by PIL‐b‐PS block copolymers in water were investigated by transmission electron microscopy and dynamic light scattering. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Linear and four‐armed poly(l‐lactide)‐block‐poly(d‐lactide) copolymers and their stereocomplexation with poly(lactide)s

Linear and four‐armed poly(l ‐lactide)‐block‐poly(d ‐lactide) (PLLA‐b‐PDLA) block copolymers are synthesized by ring‐opening polymerization of d ‐lactide on the end hydroxyl of linear and four‐armed PLLA prepolymers. DSC results indicate that the melting temperature and melting enthalpies of poly (lactide) stereocomplex in the copolymers are obviously lower than corresponding linear and four‐armed PLLA/PDLA blends. Compared with the four‐armed PLLA‐b‐PDLA copolymer, the similar linear PLLA‐b‐PDLA shows higher melting temperature (212.3 °C) and larger melting enthalpy (70.6 J g^?1). After these copolymers blend with additional neat PLAs, DSC, and WAXD results show that the stereocomplex formation between free PLA molecular chain and enantiomeric PLA block is the major stereocomplex formation. In the linear copolymer/linear PLA blends, the stereocomplex crystallites (sc) as well as homochiral crystallites (hc) form in the copolymer/PLA cast films. However, in the four‐armed copolymer/linear PLA blends, both sc and hc develop in the four‐armed PLLA‐b‐PDLA/PDLA specimen, which means that the stereocomplexation mainly forms between free PDLA molecule and the inside PLLA block, and the outside PDLA block could form some microcrystallites. Although the melting enthalpies of stereocomplexes in the blends are smaller than that of neat copolymers, only two‐thirds of the molecular chains participate in the stereocomplex formation, and the crystallization efficiency strengthens. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1560–1567     

Synthesis of biodegradable amphiphilic AB‐type diblock copolymers of lactide and depsipeptide with pendant reactive groups

The syntheses of amphiphilic AB‐type diblock copolymers composed of hydrophobic polylactide segment and hydrophilic polydepsipeptide segment with amino or carboxyl groups were performed. The protected cyclodepsipeptides cyclo[Glc‐Lys(Z)] and cyclo[Glc‐Asp(OBzl)] (where Glc is glycolic acid, Lys is lysine, Asp is aspartic acid, Z is benzyloxycarbonyl, and OBzl is benzyl) were first polymerized in tetrahydrofuran (THF) with potassium ethoxide as an initiator to obtain the corresponding protected polydepsipeptides. After the terminal hydroxyl groups of the protected polydepsipeptides were converted into the potassium alcoholates with K/naphthalene, L ‐lactide was polymerized in the presence of the corresponding polymeric alcoholates as macroinitiators in THF to obtain poly[Glc‐Lys(Z)]‐block‐poly(L ‐lactide) and poly[Glc‐Asp(OBzl)]‐block‐poly(L ‐lactide). Subsequent deprotection of Z and OBzl groups gave the objective amphiphiles poly(Glc‐Lys)‐block‐poly(L ‐lactide) and poly(Glc‐Asp)‐block‐poly(L ‐lactide), respectively. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1218–1225, 2002     

Synthesis and characterization of chiral poly(l‐lactide‐b‐hexyl isocyanate) macromonomers with norbornenyl end groups and their homopolymerization through ring opening metathesis polymerization to afford polymer brushes

We report the synthesis of the novel half‐titanocene alkoxide complex bischloro‐η⁵‐cyclopentadienyl(bicyclo[2.2.1]‐hept‐5‐en‐2‐oxy) titanium (IV), [CpTiCl₂(O‐NBE)]. This complex was employed for the synthesis of chiral poly(l ‐lactide‐b‐hexyl isocyanate) diblock copolymer bearing a norbornene end group with sequential addition of monomers. The poly(hexyl isocyanate) block is chiral due to the last l ‐lactide unit of the poly(l ‐lactide) block. This macromonomer was polymerized towards a chiral polymer brush structure with polynorbornene backbone and chiral poly(l ‐lactide‐b‐hexyl isocyanate) side chains using Grubbs first‐generation catalyst. The polymers were characterized using size exclusion chromatography (SEC), nuclear magnetic resonance (NMR), and circular dichroism (CD) spectroscopy and their thermal properties were investigated by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) analysis. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1102–1112     

Ring opening polymerization and copolymerization of L‐lactide and ɛ‐caprolactone by bis‐ligated magnesium complexes

Seven magnesium complexes ( 1–7 ) were synthesized by reaction of new ( L ³ ‐H – L ⁵ ‐H ) and previously reported ketoimine pro‐ligands with dibutyl magnesium and were isolated in 59–70% yields. Complexes 1–7 were characterized fully and consisted of bis‐ligated homoleptic ketoiminates coordinated in distorted octahedral geometry around the magnesium centers. The complexes were investigated for their ability to initiate the ring opening polymerization (ROP) of l ‐lactide (L‐LA) to poly‐lactic acid (PLA) and ?‐caprolactone (?CL) to poly‐caprolactone in the presence of 4‐fluorophenol co‐catalyst. For L‐LA polymerization, complexes containing ligand electron‐donating groups ( 1–5 ) achieved >90% conversion in 2 h at 100 °C, while the presence of CF₃ groups in 6 and 7 slowed or resulted in no PLA detected. With ?CL, ROP initiated with 1–7 resulted in lower percentage conversion with similar electronic effects. Moderate molecular weight PLA polymeric material (14.3–21.3 kDa) with low polydispersity index values (1.23–1.56) was obtained, and ROP appeared to be living in nature. Copolymerization of L‐LA and ?CL yielded block copolymers only from the sequential polymerization of ?CL followed by L‐LA and not the reverse sequence of monomers or the simultaneous presence of both monomers. Polymers and copolymers were characterized with NMR, gel permeation chromatography, and differential scanning calorimetry. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 48–59     

A novel use of Ti‐POSS as initiator of L‐lactide ring‐opening polymerization

The efficacy of a metal‐silsesquioxane, namely, heptaisobutyl (isopropoxyde)titanium‐polyhedral oligomeric silsesquioxanes (Ti‐POSS), as initiator of the ring‐opening polymerization of L ‐lactide (LLA) has been assessed. Indeed, as demonstrated by proton nuclear magnetic resonance (¹H NMR) spectroscopy and gel permeation chromatography (GPC) measurements, a well‐controlled polymerization occurs via a coordination‐insertion mechanism. Moreover, the above reaction leads to the direct insertion of the silsesquioxane molecule into the polymer backbone, thus producing a hybrid system. Differential scanning calorimetry measurements demonstrated that in comparison with a commercial poly‐L ‐lactide (PLLA), the polymers prepared with Ti‐POSS exhibit a higher crystallinity. Indeed, the presence of silsesquioxane molecules, attached to one end of the polymer chains, has been found to appreciably affect the crystal nucleation density. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of novel poly(ester carbonate)s based on pentaerythritol

Novel poly(ester carbonate)s were synthesized by the ring‐opening polymerization of L ‐lactide and functionalized carbonate monomer 9‐phenyl‐2,4,8,10‐tetraoxaspiro[5,5]undecan‐3‐one derived from pentaerythritol with diethyl zinc as an initiator. ¹H NMR analysis revealed that the carbonate content in the copolymer was almost equal to that in the feed. DSC results indicated that T_g of the copolymer increased with increasing carbonate content in the copolymer. Moreover, the protecting benzylidene groups in the copolymer poly(L ‐lactide‐co‐9‐phenyl‐2,4,8,10‐tetraoxaspiro[5,5]undecan‐3‐one) were removed by hydrogenation with palladium hydroxide on activated charcoal as a catalyst to give a functional copolymer, poly(L ‐lactide‐co‐2,2‐dihydroxylmethyl‐propylene carbonate), containing pendant primary hydroxyl groups. Complete deprotection was confirmed by ¹H NMR and FTIR spectroscopy. The in vitro degradation rate of the deprotected copolymers was faster than that of the protected copolymers in the presence of proteinase K. The cell morphology and viability on a copolymer film evaluated with ECV‐304 cells showed that poly(ester carbonate)s derived from pentaerythritol are good biocompatible materials suitable for biomedical applications. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45:1737 –1745, 2007