Investigation on sound absorption properties of kapok fibers

Sound absorption properties of natural kapok fibers have been investigated. Kapok fibrous assemblies with different bulk density, thickness, fiber length and orientation were manufactured, and their acoustical performances were evaluated by using an impedance tube instrument. Results show that the kapok fiber has excellent acoustical damping performance due to its natural hollow structure, and the sound absorption coefficients of kapok fibrous assemblies are significantly affected by the bulk density, thickness and arrangement of kapok fibers but less dependent on the fiber length. Compared with assemblies of commercial glass wool and degreasing cotton fibers, the kapok fiber assemblies with the same thickness but much smaller bulk density may have the similar sound absorption coefficients. Theoretical modelling of the acoustical damping performance of kapok fibers shows a good agreement with the experimental data. All the results demonstrate that kapok fiber is a promising light and environment-friendly sound absorption material.     

Computer simulation of crystallization kinetics and morphology in fiber-reinforced thermoplastic composites. III. Thermal nucleation

A computer simulation has been used to predict crystallization kinetics and crystalline morphology in composite materials based on thermally nucleated crystallizable matrices. As demonstrated for athermally nucleated composites, the presence of reinforcing fibers increases the complexity of the system. Fibers are shown to have a dual effect on the spherulitic crystallization process. The influence that fibers have depends on the interplay between the enhancing effects that fibers have on nucleation and the depressing effects that fibers have on spherulitic growth. Fibers that do not provide additional nuclei to the system depress the rate of crystallization relative to an unreinforced polymer, while fibers that add nuclei to the system increase the rate of crystallization. The transcrystalline morphologies that develop in thermally nucleated fiber-reinforced polymers are controlled primarily by the relative numbers of bulk and fiber nuclei. The extent of transcrystalline regions can be suppressed either by increasing the rate of bulk nucleation, or by decreasing the rate of fiber nucleation. Finally, the qualitative appearance of the morphology in the transcrystalline region was found to be indicative of the mode of fiber nucleation. © 1995 John Wiley & Sons, Inc.     

Fiber diameter measurement of bulk man-made vitreous fiber

This procedure describes a method for determining the distribution of fiber diameters of man-made vitreous fibers (MMVF) in bulk products by optical microscopy. Although some very thin fibers may be present in a typical bulk MMVF sample, repeated studies have shown that optical techniques provide a satisfactory method for the determination of the fiber diameter distribution for any product with an anticipated mean fiber diamter of 1 μm or larger. This procedure is applicable for the determination of the diamter distribution of bulk samples only and is not intended for use with aerosol samples where the number of particles is an important consideration.     

Dispersion and current-voltage characteristics of helical polyacetylene single fibers

To study the transport properties of individual helical polyacetylene (PA) fibers, we developed a method to extract a single fiber from tightly entangled ropes of helical PA bulk film. After a few minutes of sonication of a piece of helical PA bulk film in an organic solution containing surfactant, a droplet of solution is deposited on the pre-pattened electrode under argon atmosphere. AFM images show that extracted helical PA fibers are typically 10 mum in length and 100-200 nm in diameter. We found that the helicity of bulk materials is conserved. We present the temperature dependencies of current-voltage characteristics of individual helical PA fibers doped with iodine.     

Adhesion efficiency between phases in fibre-reinforced polymers by means of the concept of boundary interphase

Summary The role of the boundary interphase on the adhesion efficiency between fiber and matrix in the case of polymers reinforced with unidirectional fibers was investigated. A theoretical model was introduced considering that the composite material consists of three phases; that is, the fiber, the matrix and the interphase, material which is the part of the polymer matrix lying at the close vicinity of the fiber surface. The interphase material, having different physical properties from those of the bulk matrix, affects the overall behavior of the composite. Moreover, the quality of adhesion between the two main phases depends greatly on the nature of the interphase material. In this study we have considered that the interphase material is inhomogeneous in nature, with properties varying continuously from the fiber surface to the bulk matrix. The theory developed resulted in a criterion of the adhesion quality and in a prediction of the longitudinal modulus of elasticity of the fiber-composite.With 4 figures and 1 table     

Computer simulation of crystallization kinetics and morphology in fiber-reinforced thermoplastic composites. I. Two-dimensional case

A body of experimental evidence suggests that reinforcing fibers influence both the crystallization kinetics and morphology of those composite materials that are based on crystallizable thermoplastics. The absence of an analytical model to predict the effect of fibers on crystallization has hindered data analysis. A new approach, using computer simulation of polymer crystallization, makes it possible to study the influence that reinforcing fibers have on the crystallization kinetics and morphology of semicrystalline polymers. Fibers depress the crystallization rate relative to an unreinforced polymer since they constrain spherulitic growth by an impingement mechanism. On the other hand, reinforcing fibers can also enhance crystallization rate by providing added surface nucleation sites. This work describes a two-dimensional simplification of the crystallization process that occurs in bulk materials. It is demonstrated that the relative bulk and fiber nucleation densities, in addition to the fiber fraction, fiber diameter, and spherulitic growth rate control the crystallization kinetics and also the spherulitic and transcrystalline morphologies that develop in reinforced thermoplastic composites. © 1993 John Wiley & Sons, Inc.     

Evaluation of liquid ammonia treatment on surface characteristics of hemp fiber

In this study, we investigated the effects of liquid ammonia treatment on the surface characteristics of hemp fibers. We determined the elemental composition, morphological structure, roughness, and wettability of fiber surface using techniques such as electron spectroscopy for chemical analysis, scanning electron microscopy, atomic force microscopy, and contact angle measurements. The lignin coverage on the hemp surface was calculated from the O/C ratio and the C₁ content. The results show that lignin removal from the fiber surface was significantly greater than that from the fiber bulk. After the treatment, the O/C ratio of hemp fibers increased, and cellulose was exposed. The proportion of O₂ species that contributed to formation of hydrogen bonds increased; this further increased the number of hydrophilic groups in the hemp fibers, improving the fiber wettability. The liquid ammonia treatment did not change the large dislocation structures in hemp fibers, but the removal of noncellulosic materials from the fiber surface increased the roughness of the fiber surface.     

Diffusion of cationic polyelectrolytes into cellulosic fibers

The penetration of cationic polyelectrolytes into anionic cellulosic fibers was evaluated with fluorescent imaging techniques in order to clarify the mechanism and time scales for the diffusion process. The bulk charge of the cellulosic fibers indirectly creates a driving force for diffusion into the porous fiber wall, which is entropic in nature due to a release of counterions as the polyelectrolyte adsorbs. The individual bulk charges in the fiber cell wall also interact with the diffusing polyelectrolyte, such that the polyelectrolyte diffuses to the first available charge and consequently adsorbs and remains fixed. Thus, subsequent polyelectrolyte chains must first diffuse through the adsorbed polyelectrolyte layer before adsorbing to the next available bulk charges. This behavior differs from earlier suggested diffusion mechanisms, by which polyelectrolytes were assumed to first adsorb to the outermost surface and then reptate into the pore structure. The time scales for polyelectrolyte diffusion were highly dependent on the flexibility of the chain, which was estimated from calculations of the persistence length. The persistence length ultimately depended on the charge density and electrolyte concentration. The charge density of the polyelectrolyte had a greater influence on the time scales for diffusion. High charge density polyelectrolytes were observed to diffuse on a time scale of months, whereas the diffusion of low charge density polyelectrolytes was measured on the order of hours. An influence of the chain length, that is, steric interactions due the persistence length of the polyelectrolyte and to the tortuosity of the porous structure of the fiber wall, could only be noted for low charge density polyelectrolytes. Increasing the electrolyte concentration increased the chain flexibility by screening the electrostatic contribution to the persistence length, in turn inducing a faster diffusion process. However, a significant change in the diffusion behavior was observed at high electrolyte concentrations, at which the interaction between the polyelectrolyte charges and the fiber charges was almost completely screened.     

Properties and treatments of pulps from recycled paper. Part II. Surface properties and crystallinity of fibers and fines

Surface properties of bleached kraft pulps were evaluated before and after recycling, and after a series of chemical treatments designed to improve and/or modify the pulp characteristics. The surface free energy characteristics of the pulps were determined using the Wilhelmy technique, and ESCA and ATR-FTIR methods were used to evaluate the chemical composition of the surfaces of the pulp fibers. In general rather small changes were noted at the fiber surfaces with recycling and chemical treatment. Recycling tended to increase the acid component and decrease the base component of the surface free energy of the pulps. This could result from exposure of carboxyl groups from hemicelluloses and/or from oxidized layers from the bleaching process. ESCA analyses also indicated increased carboxyl concentration at the surfaces of the recycled fibers. Although treatment with aqueous bases and organic solvents tended to increase the hydroxyl content on the surface of recycled pulps, the chemical treatments were not beneficial to pulp quality. AFM and SEM of fiber and fine surfaces of kraft pulps revealed that the fines fraction was altered to a much greater extent with recycling. Although recycled fibers appeared to have improved wettability, these small changes in the surface characteristics do not appear to play the dominant role in the characteristics of recycled pulps. Recycling did not change the crystallinity of whole pulps, but it increased the crystallinity of the fines fraction. The increase in the crystallinity of the fines fraction and the reduction in the water retention value (WRV) and the bulk carboxyl content (xylan) of the recycled pulps, as noted in Part I of this paper, appear to play the predominant role in determining the characteristics of recycled pulps. It appears that the loss of the hemicelluloses in the bulk of the fiber with recycling is much more important for internal fibrillation than the apparent small increase of hemicelluloses at the surface of recycled fibers.     

Interfacial behavior between atmospheric-plasma-fluorinated carbon fibers and poly(vinylidene fluoride)

Atmospheric-plasma fluorination was used to introduce fluorine functionalities onto the surface of carbon fibers without affecting their bulk properties. The interfacial adhesion between atmospheric-plasma-fluorinated carbon fibers and poly(vinylidene fluoride) (PVDF) was studied by means of direct wetting measurements and single fiber pullout tests. Measured contact angles of PVDF melt droplets on modified carbon fibers show that short exposure times of carbon fibers to atmospheric-plasma fluorination (corresponding to a degree of surface fluorination of F/C = 0.01 (1.1%)) leads to improved wettability of the fibers by PVDF melts. The apparent interfacial shear strength as a measure of practical adhesion, determined by the single-fiber pullout test, increases by 65% under optimal treatment conditions. The improved practical adhesion is not due to the formation of transcrystalline regions around the fibers or a change of the bulk matrix crystallinity or to an increased surface roughness; it seems to be due to the compatibilization of the interface caused of the atmospheric-plasma fluorination of the carbon fibers.     

Is the wall of a cellulose fiber saturated with liquid whether or not permeable with CO2 dissolved molecules? Application to bubble nucleation in champagne wines

In this paper, the transversal diffusion coefficient D perpendicular of CO2 dissolved molecules through the wall of a hydrated cellulose fiber was approached, from the liquid bulk diffusion coefficient of CO2 dissolved molecules modified by an obstruction factor. The porous network between the cellulose microfibrils of the fiber wall was assumed being saturated with liquid. We retrieved information from previous NMR experiments on the self-diffusion of water in cellulose fibers to reach an order of magnitude for the transversal diffusion coefficient of CO2 molecules through the fiber wall. A value of about D perpendicular approximately 0.2D0 was proposed, D0 being the diffusion coefficient of CO2 molecules in the liquid bulk. Because most of bubble nucleation sites in a glass poured with carbonated beverage are cellulose fibers cast off from paper or cloth which floated from the surrounding air, or remaining from the wiping process, this result directly applies to the kinetics of carbon dioxide bubble formation from champagne and sparkling wines. If the cellulose fiber wall was impermeable with regard to CO2 dissolved molecules, it was suggested that the kinetics of bubbling would be about three times less than it is.     

Degradation patterns and surface wettability of electrospun fibrous mats

Degradation profiles and surface wettability are critical for optimal application of electrospun fibrous mats as drug carriers, tissue growth scaffolds and wound dressing materials. The effect of surface morphologies and chemical groups on surface wettability, and the resulting matrix degradation profiles were firstly assessed for electrospun poly(d,l-lactide) (PDLLA) and poly(d,l-lactide)-poly(ethylene glycol) (PELA) fibers. The air entrapment between the fiber interfaces clarified the effects of various surface morphologies on the surface wettability. Chemical groups with lower binding energy were enriched on the fiber surface due to the high voltage of the electrospinning process, and a surface erosion pattern was detected in the degradation of electrospun PDLLA fibers, which was quite different from the bulk degradation pattern for other forms of PDLLA. Contributed by the hydrophilic poly(ethylene glycol) segments, the degradation of electrospun PELA fibers with hydrophobic surface followed a pattern different from surface erosion and typical bulk degradation.     

Extension-Enhanced Conductivity of Liquid Crystalline Polymer Nano-Composites

Our aim here is to predict elongational flow-induced enhancements in thermal or electrical conductivity of liquid crystal polymer (LCP) nano-composites. To do so, we combine two classical mathematical asymptotic analyses: slender longwave hydro-thermo-dynamics for fibers and exact analysis of pure elongation of LCPs in solvents for bulk phases without boundary effects; and homogenization theory for effective properties of low volume-fraction spheroidal inclusions. Two implications follow: elongational flow dominates fiber free surface and thermal effects on electrical and thermal conductivity enhancements; and, there appears to be no sacrifice in enhancements by producing much higher radius, bulk fibers.     

Computer simulation of crystallization kinetics and morphology in fiber-reinforced thermoplastic composites. II. Three-dimensional case

A three-dimensional computer simulation has been used to predict crystallization kinetics and crystalline morphology in composite materials that are based on crystallizable thermoplastics. Reinforcing fibers in three-dimensional simulations show similar behavior to those in two-dimensional simulations; fibers suppress crystallization relative to an unreinforced polymer since they constrain spherulitic growth by an impingement mechanism, and also enhance crystallization by providing added surface nucleation sites. The effects of varying controlling parameters on crystallization kinetics and morphology are qualitatively the same as those observed in the two-dimensional case. The relative bulk and fiber nucleation denisities, in addition to the fiber volume fraction, fiber diameter, and spherulitic growth rate control the crystallization kinetics and crystalline morphology that develop in reinforced thermoplastic composites. It is more difficult to achieve the transcrystalline morphology in slices of three-dimensional composites than it is in two-dimensional composites because nuclei in 3-D systems are not constrained to positions in or near a 2-D plane. © 1993 John Wiley & Sons, Inc.     

On the indirect polyelectrolyte titration of cellulosic fibers. Conditions for charge stoichiometry and comparison with ESCA

The effect of electrolyte (NaHCO3) concentration on the adsorption of poly-DADMAC (poly-diallyldimethylammonium chloride) onto cellulosic fibers with different charge profiles was investigated. Surface carboxymethylated fibers were obtained by grafting carboxymethyl cellulose (CMC) onto the fiber surface and bulk carboxymethylated fibers were obtained by reacting the fibers with monochloroacetic acid. It was shown that nonionic interactions do not exist between cellulose and poly-DADMAC, rather electrostatic interactions govern the adsorption. Charge stoichiometry prevails under electrolyte-free conditions, whereas surface charge overcompensation occurs at higher electrolyte concentrations. It was shown that charge stoichiometry prevails if the thickness of the electric double layer kappa(-1) was larger than the mean distance between the charges on the fiber surface, as predicted by polyelectrolyte adsorption theories, taking lateral correlation effects into account. In a second set of experiments the ESCA technique served to independently calibrate the polyelectrolyte titrations for determining the surface charge of cellulosic fibers. Various molecular masses of poly-DADMAC were adsorbed to carboxymethylated fibers having different charge profiles. The adsorption of low M(w) poly-DADMAC (7.0 x 10(3)), analyzed by polyelectrolyte titration, was about 10 times higher than that of the high M(w) poly-DADMAC (9.2 x 10(5)). Despite the difference in accessibility of these two polyelectrolytes to the fiber cell wall, ESCA surface analysis showed, as expected, only slight differences between the two polyelectrolytes. This gives strong credibility to the idea that surface charge content of cellulosic fibers can be analyzed by means of adsorption of a high-molecular-mass cationic polymer, i.e., by polyelectrolyte titration.     

Transcrystallization of PTFE fiber/PP composites (I) crystallization kinetics and morphology

Transcrystallization of polypropylene (PP) on the polytetrafluoroethylene (PTFE) fiber was investigated. Both nucleation rate and crystal growth rate were determined by a polarized optical microscope. Based on the theory of heterogeneous nucleation, it has been found that the induction time can correlate well with the nucleation rate in determining the interfacial free energy difference function Δσ. The ratio of Δσ in the bulk matrix to that at the interface is 1.63 which implies the transcrystalline growth is favorable from a thermodynamic point of view. No difference in crystal growth rate of PP has been found in either spherulites or transcrystalline layers. On the basis of regime theory, a transition between regimes II and III was observed at ΔT = 48K. From the morphology studies, it has been found that the thickness of the transcrystalline layer increases with crystallization temperature, from 30 to 120 μm in the temperature range of 110–140°C. The growth of transcrystalline layer is hindered by the spherulites nucleated in the bulk. Moreover, the radius of spherulites adjacent to the transcrystalline layer is much smaller than that distant to the fiber. No significant increase in nucleation density at fiber ends is observed. Effect of internal stresses of fibers on the fiber's nucleating ability is not pronounced. © 1996 John Wiley & Sons, Inc.     

Bioinspired crystallization of CaCO3 coatings on electrospun cellulose acetate fiber scaffolds and corresponding CaCO3 microtube networks

This article describes the mineralization behavior of CaCO(3) crystals on electrospun cellulose acetate (CA) fibers by using poly(acrylic acid) (PAA) as a crystal growth modifier and further templating synthesis of CaCO(3) microtubes. Calcite film coatings composed of nanoneedles can form on the surfaces of CA fibers while maintaining the fibrous and macroporous structures if the concentration of PAA is in a suitable range. In the presence of a suitable concentration of PAA, the acidic PAA molecules will first adsorb onto the surface of CA fibers by the interaction between the OH moieties of CA and the carboxylic groups of PAA, and then the redundant carboxylic groups of PAA can ionically bind Ca(2+) ions on the surfaces of CA fibers, resulting in the local supersaturation of Ca(2+) ions on and near the fiber surface, which can induce the nucleation of CaCO(3) on the CA fibers instead of in bulk solution. Calcite microtube networks on the macroscale can be prepared by the removal of CA fibers after the CA@CaCO(3) composite is treated with acetone. When the CA fiber scaffold is immersed in CaCl(2) solution with an extended incubation time, the first deposited calcite coatings can act as secondary substrate, leading to the formation of smaller calcite mesocrystal fibers. The present work proves that inorganic crystal growth can occur even at an organic interface without the need for commensurability between the lattices of the organic and inorganic counterparts.     

Changes in the properties of HDPE fibers upon radiation grafting with acrylic acid

The morphology and the physical and mechanical properties of graft-modified polyethylene fibers have been studied. Two types of fibers, with the diameters of 10 μm (1.1 dtex) and 40 μm (7.5 dtex), were modified by radiation-induced grafting with acrylic acid. The extent of grafting was determined gravimetrically. Confirmation of gravimetrically obtained values was achieved using conductometric titration. The fibers were hydrated at pH 2 and pH 7. The degree of swelling was 120% at pH 2 and 200% at pH 7. The transversal distribution of polyacrylic acid in the fibers was determined. Fibers were stained and observed with an optical microscope. The diffusion of the monomer into the bulk was found to be rather fast. The changes in the total crystalline content and the lamellar thickness distributions in consequence of irradiation and grafting were determined by differential scanning calorimetry analysis. The measurements showed no effects of irradiation on the crystallinity in either type of fiber, whereas a decreasing crystallinity caused by grafting was noticed in the 40 μm fibers. The lamellar thickness distributions narrowed upon irradiation, indicating recrystallization as a result of chain scission. Wide angle x-ray scattering and Raman analysis of dry and hydrated fibers were conducted to study the behavior of the fibers in an aqueous environment. These results both showed a decreasing crystalline content caused by fiber hydration. Tensile tests were carried out to evaluate how grafting, hydration and Ca²⁺-crosslinking of grafts affected the fiber strength. Grafting and Ca²⁺-crosslinking, as well as hydration, resulted in a decreasing E-modulus for the 40 μm fibers, whereas no significant change could be noticed in the 10 μm fibers. © 1995 John Wiley & Sons, Inc.     

Melting Temperature of Individual Electrospun Poly(vinylidene fluoride) Fibers Studied by AFM-based Local Thermal Analysis

Thermal properties such as melting temperature can well reflect the microstructure of the polymer material, and have practical implications in the application of nanofibers. In this work, we investigated the melting temperature of individual electrospun poly(vinylidene fluoride)(PVDF) nanofibers with diameters ranging from smaller than 200 nm to greater than 2 μm by the local thermal analysis technique. The PVDF fibers obtained under four different conditions were found to crystallize into α and β phases, and the fiber mats showed typical values in the crystallinity and T_m with no significant difference among the four. However, analyses at single fiber level revealed broad distribution in diameter and T_m for the fibers produced under identical electrospinning condition. The T_m of individual nanofibers was found to remain constant at large diameters and increase quickly when reducing the fiber diameter toward the nanoscale, and T_m values of 220-230 ℃ were observed for the thinnest nanofibers, much higher than the typical values reported for bulk PVDF. The T_m and molecular orientation at different positions along a beaded fiber were analyzed, showing a similar distribution pattern with a minimum at the bead center and higher values when moving toward both directions. The results indicate that molecular orientation is the driving mechanism for the observed correlation between the T_m and the diameter of the nanofibers.     

Modeling of the Ion Exchange in Pulp Suspensions by Gibbs Energy Minimization

The ion exchange processes, which occur when two compartments of aqueous solutions separated by a semipermeable interface are placed in aqueous electrolyte solutions, were modeled using the multiphase Gibbs energy-minimization method. The Gibbs energy-minimization technique was applied for the ion-exchange system consisting of pulp fibers and the surrounding aqueous bulk solution. In such a system, the anionic acid groups inside the fibers cause an uneven distribution of ionic species between the solution within the fiber walls and the solution external to the fibers. The method was tested with four cation concentrations, which are naturally present in the fibers and whose partitioning between the fiber phase and the external solution phase has been described earlier. Although the Donnan distribution constant is not explicitly calculated in the Gibbs energy-minimization model, the results are consistent with the Donnan equilibrium theory. With the Gibbs energy-minimization multiphase model, the formation of solid precipitates can also be calculated.