Simultaneous determination of iron and ruthenium by preconcentration on sulfopropyl sephadex cation exchanger

A new method for the simultaneous determination of iron and ruthenium at ultra-trace levels is proposed. The method is based on the formation of the iron and ruthenium complexes with 2,4,6-tri-(2-pyridil)-1,3,5-triazine (TPTZ) in the presence of hydroxylamine hydrochloride and buffer CH₂ClCOOH/CH₂ClCOONa (pH=3.0). The formation of the complexes and their retention on a cationic resin SP-Sephadex C25 were integrated in one step at 90 °C, with stirring for 90 min. Under these conditions a high preconcentration level was achieved for both analytes. The complexes retained on the solid phase were evaluated by second derivative spectrophotometry. The selected analytical wavelengths were 539.7 and 553.3 nm for the determination of ruthenium and iron, respectively, by using the zero crossing approach. The detection and quantification limits were 0.54 ng ml⁻¹ and 1.79 ng ml⁻¹ for ruthenium and 0.41 ng ml⁻¹ and 1.38 ng ml⁻¹ for iron. The proposed method was applied to the determination of both analytes in synthetic mixtures.     

Flame atomic absorption spectrometric determination of Cd(II), Ni(II), Co(II) and Cu(II) in tea and water samples after simultaneous preconentration of dithizone loaded on naphthalene

A simultaneous preconcentration procedure for the determination of Cd(II), Ni(II), Co(II) and Cu(II) by atomic absorption spectrometry is described. The method is based on solid phase extraction of the metal ions on dithizone loaded on naphthalene in a mini-column, elution with nitric acid and determination by flame atomic absorption spectrometry. The sorption conditions including NaOH concentration, sample volume and the amount of dithizone were optimized in order to attain the highest sensitivity. The calibration graph was linear in the range of 0.5–75.0 ng ml^?1 for Cd(II), 1.0–150.0 ng ml^?1 for Ni(II), 1.0–150.0 ng ml^?1 for Co(II) and 1.0–125.0 ng ml^?1 for Cu(II) in the initial solution. The limit of detection based on 3S_b was 0.13, 0.32, 0.33 and 0.43 ng ml^?1 for Cd(II), Ni(II), Co(II) and Cu(II), respectively. The relative standard deviations (R.S.D) for ten replicate measurements of 20 ng ml^?1of Cd(II), 100 ng ml^?1 of Ni(II), Co(II) and 75 ng ml^?1 of Cu(II) were 3.46, 2.43, 2.45 and 3.26%, respectively. The method was applied to the determination of Cd(II), Ni(II), Co(II) and Cu(II) in black tea, tap and river water samples.     

Simultaneous determination of cobalt and chromium by ion chromatography with chemiluminescence detection and its application to glass analysis

A method is described for the simultaneous determination of very low levels of Co and Cr by high performance ion chromatography coupled with a chemiluminescence detection system. 0.1M K₂SO₄ solutions, adjusted to pH 3.0, were used as eluent to separate Co(II) and Cr(III) between them and from interferents. The detection system was the chemiluminescence of luminol/ H₂O₂ in alkaline medium catalyzed by such transition metals. Using a matrix solution analogous to soda-lime silica glass (dissolved in acids) calibration graphs were linear up to 0.5 ng ml^–1 for cobalt and up to 250 ng ml^–1 for chromium. The corresponding calculated detection limits (3 s) in such matrix were 0.05 ng ml^–1 and 15 ng ml^–1 for Co and Cr, respectively. The relative standard deviations were 1.4% at 0.5 ng ml^–1 Co level and 2.8% at the 200 ng ml^–1 Cr level. No interferences were observed from the more common metals, particularly those present in glass samples. The ion chromatography/ chemiluminescent method proposed has been successfully applied to the analysis of Co and Cr in glasses.     

Spectrophotometric study of Cd(II), Pb(II), Hg(II) and Zn(II) complexes with 5,10,15,20-tetrakis(4-carboxylphenyl)porphyrin

The reaction of 5,10,15,20-tetrakis(4-carboxylphenyl)porphyrin (TCPP) with Cd(II), Pb(II), Hg(II) and Zn(II) was studied spectrophotometrically and kinetics, equilibrium constants as well as photodecomposition of complexes were determined. It was verified that these metal ions with large radius accelerate the incorporation reaction of zinc into TCPP. On the basis of the mechanism and kinetics of this reaction, a sensitive method for the spectrophotometric determination of trace amounts of Zn(II) has been developed. The molar absorptivity of examined Zn-TCPP complex and Sandell's sensitivity at 423 nm were 3.5×10⁵ M⁻¹ cm⁻¹ and 18.3 ng cm⁻². The detection limit for the recommended procedure was 1.4×10⁻⁹ M (0.9 ng ml⁻¹) and precision in range 20-100 ng ml⁻¹ not exceeds 2.7% RSD. The proposed method applied for zinc determination in natural waters and nutritional supplement was compared with AAS results and declared value.     

Determination of cadmium by flame atomic absorption spectrometry after preconcentration on naphthalene-methyltrioctylammonium chloride adsorbent as tetraiodocadmate (II) ions

A sensitive and simple solid-phase preconcentration procedure for enrichment of cadmium prior to analysis by flame atomic absorption spectrometry (FAAS) is described. The method is based on the adsorption of cadmium as CdI₄²⁻ on naphthalene-methyltrioctylammonium chloride adsorbent, elution by nitric acid and subsequent determination by FAAS. The effect of pH, iodide concentration, sample flow rate, volume of the sample and diverse ions on the recovery of the analyte was investigated and optimum conditions were established. A preconcentration factor of 40 was achieved using the optimum conditions. The calibration graph was linear in the range 1-100 ng ml⁻¹ cadmium in the initial solution. The detection limit based on the 3S_b criterion was 0.6 ng ml⁻¹ and the relative standard deviations (RSD) were 3.9 and 1.05% for 5 and 40 ng ml⁻¹, respectively (n=8). The method was successfully applied to the determination of cadmium added to river, tap and Persian Gulf water samples.     

Spectrophotometric determination of trace lead in water after preconcentration using mercaptosephadex

A highly sensitive and selective spectrophotometric method for determination of trace lead in water after pre-concentration using mercaptosephadex (MS-50) has been developed, the method based on the color reaction of lead(II) with dibromohydroxylphenylporphyrin. Under optimal condition, lead(II) reacts with the reagent to form a 1:2 yellow complex in presence of TritonX-100, which has a maximum absorption peak at 479 nm. The color reaction can complete rapidly and remain stable for 24 h in room temperature. The molar absorption coefficient of the lead complex, the limit of quantification, the limit of detection and relative standard deviations were found to be 2.35×10⁵ l mol⁻¹ cm⁻¹, 4.3, 1.4 ng ml⁻¹ and 1.0%, respectively. The absorbance of the lead complex at 479 nm is linear up to 0.48 μg ml⁻¹ of lead(II). The effect of various co-existing ions in water were examined seriously. No interference was observed. Moreover, a simple pre-concentration method for trace lead in water was also studied using MS-50. It was found that trace lead in water can be adsorbed in 1.0 mol l⁻¹ HCl and dissociated from MS-50 with 4.0 mol l⁻¹ HCl quantitatively, that improves the selectivity and the sensitivity of method (its detection limit (3 s) changed into 0.2 ng ml⁻¹ of lead) obviously. The proposed method has been applied to determine trace lead in water samples with satisfactory results.     

Flow-injection spectrophotometry of vanadium by catalysis of the bromate oxidation of N,N'-bis(2-hydroxyl-3-sulfopropyl)-tolidine

A highly sensitive flow-injection method is proposed for the catalytic determination of vanadium(V) at sub-nanogram per milliliter levels using a new indicator reaction. The method is based on the catalytic effect of vanadium(V) on the bromate oxidation of N,N′-bis(2-hydroxyl-3-sulfopropyl)-tolidine. 1,2-Dihydroxybenzene-3,5-disulfonate was used as an activator in the vanadium(V)-catalyzed reaction and significantly enhanced the sensitivity of the method. Vanadium(V) in the range 0.01-3.0 ng ml⁻¹ was easily determined with sampling rate of about 30 h⁻¹. Vanadium(IV) could be also determined. The limit of detection (S/N=3) was 0.008 ng ml⁻¹ and the relative standard deviations were 1.4 and 1.6% for ten determinations of 0.2 ng ml⁻¹ vanadium(IV) and vanadium(V), respectively. Interferences from metal ions could be suppressed by the addition of ethylenediamine-N,N,N′,N′-tetrakis(methylenephosphonic acid) as a masking agent. The proposed method was successfully applied to the determination of vanadium in water samples.     

High sensitive determination of trace amount of cobalt by catalytic adsorptive stripping voltammetry

A very sensitive and selective catalytic adsorptive cathodic stripping procedure for trace measurements of cobalt is presented. The method is based on adsorptive accumulation of cobalt-CCA (calcon carboxylic acid) complex onto a hanging mercury drop electrode followed by reduction of the adsorbed species by voltammetric scan using differential pulse modulation. The reduction current is enhanced catalytically by nitrite. The effect of various parameters such as pH, concentration of CCA, concentration of nitrite, accumulation potential and accumulation time on the selectivity and sensitivity were studied. The optimum condition for the analysis of cobalt, include pH 5.2 (Acetate buffer), 2.1 μM clacon carboxylic acid, 0.032 M sodium nitrite and an accumulation potential of 0.05 V (versus Ag/AgCl). Under these optimum conditions and for an accumulation time of 60 s, the measured peak current at −0.480 V is proportional to the concentration of cobalt over the entire concentration range tested 0.003–2.0 ng ml⁻¹ with a detection limit of 1 pg ml⁻¹ for an accumulation time of 60 s and 2.0–10.0 ng ml⁻¹ for an accumulation time of 40 s. The relative standard deviations for ten replicate measurement of 0.5 ng ml⁻¹ of cobalt were 3.1%. The main advantage of this new system is the microtrace Co(II) determination by ASV. The method was applied to determination of cobalt in a water sample and some analytical grade salts with satisfactory results. Published in Elektrokhimiya in Russian, 2009, Vol. 45, No. 2, pp. 221–228. The article is published in the original.     

Determination of trace iron in indium phosphide wafer by on-line matrix separation and inductively coupled plasma mass spectrometry

A method for the determination of iron in indium phosphide (InP) wafer is proposed. In the present experiment, an on-line matrix separation system using an ion exchange column was combined with inductively coupled plasma mass spectrometry (ICP-MS) for the determination of ng g⁻¹ level of iron. In the on-line matrix separation, indium and iron in the sample solution was passed through a strongly-basic anion exchange resin column with the 9 M HCl carrier solution, where indium was eluted from the column and iron was adsorbed on it. Then, iron was eluted with the carrier solution of 0.3 M HCl containing 1 ng ml⁻¹ cobalt, and it was directly introduced into the ICP-MS nebulizer. In ICP-MS measurement, cobalt in the carrier solution was used as an internal standard to correct the change in sensitivity due to matrix effect, and the peak area integration was performed to quantify iron and cobalt in the integration time range of 20-60 s from the start of the cobalt solution flow. The detection limit (3σ) for iron was 3 ng g⁻¹, and the recoveries for iron in the 0.8, 2.4, and 8.0% indium solutions were almost 100%. The method was applied to the determination of iron in commercially available iron-doped InP wafers. The obtained results for InP wafer samples with the high iron concentration were in good agreement with those obtained by graphite furnace atomic absorption spectrometry (GFAAS).     

Sequential flow injection analysis of ammonium and nitrate using gas phase molecular absorption spectrometry

A flow injection method on the basis of gas phase molecular absorption is described for the sequential determination of ammonium and nitrate. Two hundred microliters of sample solution is injected into the flow line. For ammonium determination, the sample zone is directed to a line in which reacts with NaOH (13 M) and produces ammonia. But for nitrate determination, the sample zone is passed through the on-line copperized zinc (Zn/Cu) reduction column and produces ammonium ion and in the follows ammonia. The produced ammonia in both cases is purged into the stream of N₂ carrier gas. The gaseous phase is separated from the liquid phase using a gas-liquid separator and then is swept into a flow through cell, which has been positioned in the cell compartment of an UV-Vis spectrophotometer. The absorbance of the gaseous phase is measured at 194 nm. Under selected conditions for sequential analysis of ammonium and nitrate, linear relations were found between the peak heights of absorption signals and concentrations of ammonium (10-650 μg ml⁻¹) and nitrate (20-800 μg ml⁻¹). The limit of detections for ammonium and nitrate analysis were 8 and 10 μg ml⁻¹, respectively. The relative standard deviations of repeated measurements of 50 μg ml⁻¹ of ammonium and nitrate were 2.0, 2.9%, respectively. Maximum sampling rate was about 40 samples/h. The method was applied to the determination of ammonium in pharmaceutical products and the sequential determination of ammonium and nitrate in spiked water samples.     

Flow Injection with an Integrated Retention/Photometric Detection Unit for the Determination of Iron in Water

An integrated retention/photometric detection method for the determination of microamounts of iron was developed. The method is based on the retention of the reaction product of the analyte with ferrozine in a flow cell packed with an anion exchange support, and on the subsequent elution of the retained complex with a solution of 1.5% sodium peroxide, which allows the reuse of the system. The method is highly selective and has a detection limit (3σ) of 4.3 ng ml⁻¹. Iron was thus determined in the range 10–200 ng ml⁻¹with a relative standard deviation of 1–3% (n= 11). The method was applied to the determination of iron in tap and river water and the results were consistent (2%) with those provided by AAS.     

Determination of ternary mixtures of penicillin G, benzathine and procaine by liquid chromatography and factorial design study

In the present work, a rapid and sensitive method for simultaneous determination of penicillin G (PG), benzathine (BE) and procaine (PR) in drug and serum media is introduced. The polar hydro-organic (55/45) mobile phases containing an aqueous solution adjusted to pH = 3.7 and an organic solvent (MeOH) including triethylamine (TEA) and trifluroacetic acid (TFA) are used. The flow rate of 1 ml min⁻¹, a C₈ column (150 mm × 46 mm) with 5 μm i.d. and wavelength at 215 nm are selected for optimal separation condition. The limit of detection (LOD), linear concentration range and relative standard deviation (R.S.D.) of this method for the PG are 1.1 μg ml⁻¹, 10-2400 μg ml⁻¹ and 1.7% and for the BE are 1.2 μg ml⁻¹, 12-2100 μg ml⁻¹ and 1.8% and for the PR are 1.5 μg ml⁻¹, 20-2000 μg ml⁻¹ and 2%, respectively. The factorial design is used for the determination of main and interaction effects of pH, flow rate and concentration of MeOH, TEA and TFA in the separation at two levels. Also, the analysis of variance (ANOVA) table is obtained. The results show that TFA and TEA have higher effect than concentration of MeOH, pH and flow rate factors.     

Spectrophotometric determination of molybdenum based on charge transfer complexes sensitized by copper(II)

A new high sensitive spectrophotometric determination of trace molybdenum was investigated. The sensitivity of the determination of molybdenum, which based on the color charge transfer complex of molybdotungstophosphate-3,3′,5,5′-tetramethylbenzidine, was greatly enhanced by copper(II) ions in the presence of polyvinyl alcohol. The improved method maintained the features of simplicity, rapidity and selectivity, especially eliminating the interference from tungsten. Under the optimum conditions, Beer's law was obeyed over the range from 2 to 32 ng ml⁻¹ molybdenum with molar absorptivity being 4.92×10⁵ l mol⁻¹ cm⁻¹ at 660 nm. The relative standard deviation was 1.2% under nine determinations for 16 ng ml⁻¹ Mo(VI). The present method had been applied to the determination of trace molybdenum in tungsten ores with satisfactory results.     

Differential pulse cathodic stripping adsorption voltammetric determination of trace amounts of lead using factorial design for optimization

A sensitive cathodic stripping voltammetric method is developed for determination of lead(II), with adsorptive collection of complexes with Pyrogallol red (PGR) on to a hanging mercury drop electrode. After accumulation of the complex at −0.80 V vs. Ag/AgCl reference electrode, the potential is scanned in a negative direction from −0.20 to −0.50 V with differential pulse method. Then the reduction peak current for the lead(II)-PGR complex is measured at −0.39 V. The influence of reagent and instrumental variables was completely studied by factorial design analysis. The optimum analytical conditions for the determination of lead(II) were established. Under optimum conditions, lead(II) determined in the range of 0.1-30.0 ng ml⁻¹ with a limit of detection of 0.06 ng ml⁻¹. The method is successfully applied to determination of lead(II) in water sample.     

Spectrophotometric flow-injection analysis of mercury(II) in pharmaceuticals with p-nitrobenzoxosulfamate

A new, simple and rapid spectrophotometric FI method for the accurate and precise determination of Hg(II) in pharmaceutical preparations has been developed. The method is based on the measuring the decrease of absorbance intensity of p-nitrobenzoxosulfamate (NBS) due to the complexation with Hg(II). The absorption peak of the NBS, which is decreased linearly by addition of Hg(II), occurs at 430 nm in 2×10⁻⁴ mol l⁻¹ HNO₃ as a carrier solution. Optimization of chemical and FI variables has been made. A micro column consisting of several packing materials applied instead of reaction coil was also investigated. A background level of Fe(III) maintained in reagent carrier solution with NBS was found useful for sensitivity and selectivity. Under the optimized conditions, the sampling rate was over 100 h⁻¹, the calibration curve obtained were linear over the range 1-10 μg ml⁻¹, the detection limit was lower than 0.2 μg ml⁻¹ for a 20 μl injection volume, and the precision [S_r=1% at 2 μg ml⁻¹ Hg(II) (n=10)] was found quite satisfactory. Application of the method to the analysis of Hg(II) in pharmaceutical preparations resulted a good agreement between the expected and found values.     

Solid phase preconcentration of iron as methylthymol blue complex on naphthalene-tetraoctylammonium bromide adsorbent with subsequent flame atomic absorption determination

A sensitive and selective preconcentration method for the determination of trace amounts of iron by atomic absorption spectrometry has been developed. Iron forms a complex with methylthymol blue at pH=3. This complex is retained by naphthalene tetraoctylammonium bromide adsorbent in a column with a height of about 2 cm. The adsorbed metal complex is then eluted from the column with nitric acid and its iron content is determined by flame atomic absorption spectrometry (FAAS). The effect of different variables such as pH, reagent concentration, flow rate and interfering ions on the recovery of the analyte was investigated. The calibration graph was linear in the range 25-350 ng ml⁻¹ of iron in the initial solution with r=0.9994. The limit of detection based on 3S_b criterion was 12 ng ml⁻¹ and the relative standard deviation for eight replicate measurements of 150 and 300 ng ml⁻¹ of iron was 3.1 and 1.8%, respectively. This procedure was successfully applied to the determination of iron in tap and sewage water samples.     

Direct spectrophotometric determination of calcium in clinical samples with carboxyazo-p-CH3

A highly sensitive and relatively interference-free spectrophotometric method for determination of calcium is described. The method is based on the reaction between calcium ions and carboxyazo-p-CH₃ in aqueous citrate medium of pH 7, to form a blue complex with maximum absorption at 716 nm. The calibration is linear up to 0.12 μg ml⁻¹ calcium with a repeatability (R.S.D.) of 1.0% at a concentration of 0.04 μg ml⁻¹ (n=5). The molar absorptivity of the complex and Sandell’s sensitivity are 3.5×10⁵ l mol⁻¹ cm⁻¹ and 0.11 ng cm⁻², its 10σ limit of quantification and the 3σ limit of detection were found to be 0.3 ng ml⁻¹ and 0.09 ng ml⁻¹ respectively. The influence of reaction variables and the effect of interfering ions are studied; no interference was observed in clinical samples. The proposed method has been applied directly to the determination of calcium in clinical samples without the need for pre-concentration, masking metal ions and digesting samples.     

Chemiluminescence determination of barbituric acid using Ru(phen)(3)(2+)-Ce(IV) system

A chemiluminescence (CL) method for the determination of barbituric acid (BA) was proposed, which is based on the enhancement of BA to the CL intensity of Tris-(1,10-phenanthroline)ruthenium(II) (Ru(phen)₃²⁺)-cerium(IV) (Ce(IV)) system. The concentration of BA is proportional to the CL intensity in the range of 5.0×10⁻³-2.0 μg ml⁻¹. The detection limit is 6.9×10⁻⁴ μg ml⁻¹. The relative standard deviation (R.S.D.) of determining 11 samples containing 0.20 μg ml⁻¹ BA is 3.2%. This CL method has been successfully applied to the determination of BA in the synthetic samples. The mechanism of CL reaction was studied.     

Direct immunoassay of estriol in pregnancy serum by capillary electrophoresis with laser-induced fluorescence detector

A simple and sensitive capillary electrophoretic immunoassay (CEIA) was described for the determination of estriol (E₃) in pregnant women's serum. The method was based on the competitive reaction of fluorescein-labeled E₃ antigen and E₃ with limited amounts of monoclonal antibody. The addition of the thermally reversible hydrogel, poly-N-iso propylacrylamide (pNIPA) in the buffer serving as a replaceable packing material, improved the reproducibility of the method. With laser-induced fluorescence detector (LIF), this method can be applied to determine E₃ at concentrations lower to 31.6 pg ml⁻¹. Recoveries from human steroid-free serum matrix were greater than 94% with relative standard deviation (R.S.D.) values less than 3.5%. Serum E₃ levels of ten normal pregnant women were measured at the range of 10.2-15.6 ng ml⁻¹.     

A novel spectrofluorimetric method for the ultra trace analysis of nitrite and nitrate in aqueous medium and its application to air, water, soil and forensic samples

A highly sensitive and virtually specific method has been developed for the trace and ultra trace 5 ng ml⁻¹-1 μg ml⁻¹ fluorimetric analysis of nitrite. The method is based on the quenching action of nitrite on the native fluorescence of murexide (ammonium purpurate) [λ_ex=349.0 nm, λ_em=444.5 nm] in the acid range of 0.045-0.315 (M) H₂SO₄. The method is very precise and accurate (S.D.=±0.4877 and R.S.D.=0.4878% for the determination of 0.1 μg ml⁻¹ of nitrite in 11 replicates). Relatively large excesses of over 35 cations and anions do not interfere. The proposed technique has been successfully applied for the determination of nitrite and nitrate in ground water, surface water and sea water, nitrite in soil and nitrate in forensic samples. The method has also been extended for the analysis of NO_x in air.