三角形光脉冲在正色散光纤中产生的实验研究

利用一种无源非线性脉冲整形方法, 实现了在普通正色散(ND)光纤中产生三角形光脉冲, 此方法依赖于脉冲预啁啾和脉冲在ND光纤中传输时群速度色散与自相位调制的相互作用. 实验研究表明, 在较宽的脉冲预啁啾值范围内, 通过优化脉冲输入功率和脉冲传输的ND光纤长度, 均可得到典型的三角形光脉冲: 脉冲时域形状前后沿的变化率接近恒定、整个脉冲具有线性频率啁啾. 另外, 在不同的脉冲预啁啾下, 要得到高质量的三角形光脉冲, 均需要较高的脉冲输入功率; 并且脉冲预啁啾较大时, 三角形脉冲的形成对ND光纤长度和脉冲输入功率有较大的容差, 易获得三角形光脉冲.     

用于激光聚变驱动器的全光纤、全固化光脉冲产生系统

报道一种全固化、全光纤的用于高功率激光驱动的惯性约束聚变驱动器的光脉冲产生系统,采用单纵模振荡器输出连续激光信号,经过相位调制器和振幅调制器,得到一个时间波形上已整形且具有一定带宽(约0.1 nm)的激光脉冲,经光纤放大器放大并经光纤分束器分束后同时输出四路激光脉冲,各路激光脉冲先通过时间同步调整单元精确控制时间同步关系后,经可编程光纤衰减器调节各路之间的功率平衡后再通过光纤放大器做进一步放大并通过150 m光纤传输输出至预放系统.该光纤系统可输出0.3—20 ns、带宽0.1 nm、能量数纳焦的几乎任意 关键词： 激光聚变驱动器 前端 光纤激光系统     

Cross-validation of theoretically quantified fiber continuum generation and absolute pulse measurement by MIIPS for a broadband coherently controlled optical source

The predicted spectral phase of a fiber continuum pulsed source rigorously quantified by the scalar generalized nonlinear Schrödinger equation is found to be in excellent agreement with that measured by multiphoton intrapulse interference phase scan (MIIPS) with background subtraction. This cross-validation confirms the absolute pulse measurement by MIIPS and the transform-limited compression of the fiber continuum pulses by the pulse shaper performing the MIIPS measurement, and permits the subsequent coherent control on the fiber continuum pulses by this pulse shaper. The combination of the fiber continuum source with the MIIPS-integrated pulse shaper produces compressed transform-limited 9.6 fs (FWHM) pulses or arbitrarily shaped pulses at a central wavelength of 1020 nm, an average power over 100 mW, and a repetition rate of 76 MHz. In comparison to the 229-fs pump laser pulses that generate the fiber continuum, the compressed pulses reflect a compression ratio of 24.     

石墨烯被动锁模全正色散掺镱光纤激光器中的暗脉冲及其谐波

报道了一种基于石墨烯被动锁模的全正色散掺镱环形光纤激光器. 在激光器腔中应用激光诱导沉积法制备的石墨烯可饱和吸收体, 通过调节抽运光功率和偏振控制器的角度分别得到了明脉冲及其二阶谐波, 暗明脉冲对和暗脉冲及其二、三阶谐波这三类不同的脉冲. 其中, 暗明脉冲对和暗脉冲在基于石墨烯被动锁模的掺镱光纤激光器实验中都是第一次被观察到. 本文根据实验结果结合模拟分析了暗脉冲的产生机理, 并研究对比了明脉冲谐波和暗脉冲谐波产生的原因.     

Yb-doped fiber oscillator generating 41 fs wave-breaking-free pulses

We report on the generation of wave-breaking-free pulses from an Yb-doped fiber oscillator at 1.03 μm by using the nonlinear polarization rotation mode-locking. The average output power reached 113 mW as limited by available pump power of 578 mW. The generated pulses had a pulse energy up to 2 nJ and could be externally compressed down to 41 fs. The output pulses exhibited a smooth spectrum without any side lobe or temporal wave-packet breaking due to the nonlinear phase modulation in an additional Erdoped fiber acted as a saturable absorber in the fiber laser.     

Femtosecond parabolic pulse nonlinear compression with gas-filled hollow-core fiber

We study theoretically the spectral intensity evolutions of the femtosecond Gaussian and parabolic pulses with different initial pulse energies and compare the nonlinear compressions of these pulses based on a meter-long hollow-core fiber filled with neon for different initial pulse durations. The pulses are first coupled into gas-filled hollow-core fiber for spectrum broadening, then compressed by the optimal chirp compensation. The parabolic pulse possesses a shorter pulse duration, larger peak power, and cleaner wings than Gaussian pulse. The properties are useful for compressing the pulses and thus generating the high-energy, short-duration pulses.     

1 MHz repetition rate hollow fiber pulse compression to sub-100-fs duration at 100 W average power

We report on nonlinear pulse compression at very high average power. A high-power fiber chirped pulse amplification system based on a novel large pitch photonic crystal fiber delivers 700 fs pulses with 200 μJ pulse energy at a 1 MHz repetition rate, resulting in 200 W of average power. Subsequent spectral broadening in a xenon-filled hollow-core fiber and pulse compression with chirped mirrors is employed for pulse shortening and peak power enhancement. For the first time, to our knowledge, more than 100 W of average power are transmitted through a noble-gas-filled hollow fiber. After pulse compression of 81 fs, 93 μJ pulses are obtained at a 1 MHz repetition rate.     

高重复频率飞秒掺镱光纤放大器

 数值分析了掺镱单模光纤放大器的最佳增益光纤长度，并在实验上对掺镱单模光纤放大器和光栅对压缩器进行了研究。以最大平均输出功率为7 mW、重复频率为25.4 MHz、脉宽为56 ps的被动锁模环形腔掺镱光纤激光器作为种子脉冲，用250 mW的976 nm单模半导体激光器分别泵浦3种不同长度的掺镱单模光纤，对种子光进行放大，并用光栅对压缩器对放大后的脉冲在不同光栅距离上进行了压缩实验研究。当掺镱单模光纤长度为1.2 m时得到了较好的放大效果，种子脉冲被放大到140 mW，相应的增益为13 dB，放大后的单脉冲能量为5.5 nJ。在光栅距离为14.1 cm时获得了最短440 fs的脉冲，压缩后的功率为43 mW，相应的峰值功率为3.8 kW。     

66 W average power from a microjoule-class sub-100 fs fiber oscillator

Performance scaling of passively mode-locked ultrashort-pulse fiber oscillators in terms of average power, peak power, and pulse energy is demonstrated. A very-large-mode-area fiber laser in an all-positive group-velocity-dispersion ring cavity configuration with intracavity spectral filter, mode-locked by nonlinear polarization evolution, emits 66 W of average power at 76 MHz repetition rate, corresponding to 0.9 μJ pulse energy. The pulses are dechirped to 91 fs outside the cavity with an average power of 60 W remaining after the compressor. The generated pulse peak power is as high as 7 MW.     

High-energy soliton pulse generation with a passively mode-locked Er/Yb-doped multifilament-core fiber laser

We report the generation of high-energy short pulses from a mode-locked erbium/ytterbium-doped large-mode-area multifilament-core fiber laser operating in the purely anomalous dispersion regime. The self-starting fiber laser emits 400 mW of average output power at a pulse repetition rate of 44 MHz, corresponding to a pulse energy of 9.1 nJ. The laser produces near transform-limited output pulses with pulse duration of 1.6 ps, corresponding to 5 kW peak power. This new type of low-nonlinearity fibers demonstrates the power and energy scaling potential of fiber-based short pulse lasers in the eye-safe region.     

High-power all-normal-dispersion femtosecond pulse generation from a Yb-doped large-mode-area microstructure fiber laser

We report on an all-normal-dispersion mode-locked fiber laser based on a large-mode-area Yb-doped microstructure fiber and using a high nonlinear modulation depth semiconductor saturable absorber mirror. The laser delivers 3.3 W of average output power with positively chirped 5.5 ps pulses at a center wavelength of 1033 nm. The pulse repetition rate is 46.4 MHz, which results in an energy per pulse of 71 nJ. These pulses are extracavity dechirped down to 516 fs by using bulk gratings. The average power of the dechirped pulses is 2.3 W, which corresponds to a peak power of more than 96 kW.     

基于类噪声方波脉冲的掺铒光纤激光器

搭建了长腔"8"字型掺铒光纤激光器,并对产生的谐波锁模方波脉冲进行了实验研究.结果表明,该脉冲具有光滑的宽带光谱,示波器上显示为方波脉冲,但自相关迹证实其为类噪声脉冲,即为类噪声方波脉冲;通过调节偏振控制器和泵浦功率等激光器腔内参量,获得了高达5阶的谐波锁模类噪声方波脉冲;该类噪声方波脉冲并非可以无限增大脉冲能量,而是在一定条件下产生脉冲分裂,出现谐波锁模方波脉冲现象.     

High power all-fibered femtosecond master oscillator power amplifier at 1.56 μm

Direct amplification of output from chirped pulse oscillator (CPO) to 3.3?W of average power (pulse energy of 118?nJ in 20?ps pulse duration before compression) was achieved in a properly designed cladding pumped large mode area Er-doped fiber. Various configurations of CPO cavity with different FWHM of output spectrum and pulse duration were investigated. Fourier limit compression with 480?fs pulse duration and 32?kW peak power has been obtained for pulses with 14.8?nm FWHM spectrum. Subsequent nonlinear compression in a standard SMF-28 fiber yielded pulses as short as 145?fs.     

自由耦合输出的大模场面积光子晶体光纤锁模激光器

对一种基于高增益掺Yb³⁺大模场面积光子晶体光纤（PCF）的锁模激光器进行了简化线型腔结构的实验和理论研究.实验中直接使用塌陷打磨为0°角的光纤端面作为一端腔镜,利用其端面反馈获得了激光振荡,并进一步利用半导体可饱和吸收镜（SESAM）和光栅对的滤波作用实现了稳定的锁模运转.通过调节滤波程度,使激光器实现了从宽带滤波锁模到窄带滤波锁模的连续可调谐.在宽带滤波锁模的条件下,得到了最大平均输出功率2.2 W,单脉冲能量29.3 nJ,脉冲宽度367 fs的锁模脉冲输出;在窄带滤波锁模的条 关键词： 飞秒激光 光纤激光器 光子晶体光纤 大模场面积光纤     

光纤激光器直接输出的高功率贝塞尔超短脉冲

构建了一种能够直接输出高功率贝塞尔超短脉冲的光纤激光放大器. 该方案基于在光纤端面特殊设计和制备的微型负轴锥镜, 针对常规超短脉冲光纤激光放大系统所设计, 不需要引入其他分立整形器件, 避免了目前基于轴锥透镜产生贝塞尔光束的通用方法所带来的额外烦琐准直工作, 极大简化了产生贝塞尔光束的方法. 其中的微型负轴锥镜由聚焦粒子束刻蚀法在一段掺镱大模场光子晶体光纤的端面制备, 它和光纤激光系统中的固有准直透镜构成了集成化的光束整形器件. 基于数值模拟结果成功搭建的系统与理论设计一致, 直接输出了在米量级具有高度准直无衍射特性的啁啾皮秒贝塞尔超短脉冲波包, 平均功率高达10.1 W, 对应脉冲能量178 nJ, 经过光栅对压缩后脉冲宽度可达140 fs. 关键词： 衍射 超短脉冲产生 光纤器件 光纤激光器     

Optimum peak pulse investigation for OTDR instrumentation

This work presents an experimental study of the optimal peak-power pulse for testing telecommunications fibers. Using a Q-switched fiber laser at 1060 nm, we obtained 100-ns pulses at a 10-kHz repetition rate with an average power of 60 mW corresponding to a 60-W peak power. With these pulses, we generated up to fifth-order Stokes within the fiber, with wavelengths on the third window of telecommunications. We demonstrate that the power exceeding the optimum peak power does not increase the penetration length of OTDR systems because of the pump depletion. The shape of the Stokes-shifted pulses attained at the end of the test fiber is similar to the pulse shape from a Q-switched fiber laser, also showing the possibility to produce suitable peak powers and pulse shapes for OTDR applications at different wavelengths.     

High average and peak power femtosecond large-pitch photonic-crystal-fiber laser

We report on the generation of high-average-power and high-peak-power ultrashort pulses from a mode-locked fiber laser operating in the all-normal-dispersion regime. As gain medium, a large-mode-area ytterbium-doped large-pitch photonic-crystal fiber is used. The self-starting fiber laser delivers 27 W of average power at 50.57 MHz repetition rate, resulting in 534 nJ of pulse energy. The laser produces positively chirped 2 ps output pulses, which are compressed down to sub-100 fs, leading to pulse peak powers as high as 3.2 MW.     

基于光纤中SBS相位共轭的自调Q光纤激光器

分析了利用光纤中的受激布里渊散射(stimulated Brillouin scattering,SBS)相位共轭效应进行激光腔内调Q,产生ns量级脉冲激光的原理,并对利用该效应产生的激光脉冲波形和脉冲形成过程进行了数值模拟,得到的脉冲波形与SBS相位共轭反射率随时间变化曲线基本一致,表明利用光纤中的SBS相位共轭作用调Q具有可行性.据此,对采用单模光纤(single-mode fiber,SMF)作为SBS池的Er³⁺掺杂调Q光纤激光器进行实验研究.当单模光纤长度为1.5 m时,在45 mW的光抽运功率下得到脉宽约2.6ns,脉冲周期58.23ns,平均功率7.35mW的激光脉冲.进一步的研究表明:激光器中相位共轭镜的形成与SBS介质长度有关,SBS介质过长,斯托克斯线之间无固定的相位关系,不能形成相干叠加,SBS相位共轭腔不能形成;SBS介质过短,腔内正交偏振模光子寿命的改变使脉冲出现双峰现象.脉冲形成后其属性只与SBS动态属性有关.     

Cavity-enhanced similariton Yb-fiber laser frequency comb: 3 x 10(14) W/cm2 peak intensity at 136 MHz

We report on a passive cavity-enhanced Yb-fiber laser frequency comb generating 230 MW of peak power (3 kW of average power) at a 136 MHz pulse repetition rate. The intracativy peak intensity of 3 x 10(14) W/cm2 for the 95 fs pulse is sufficient to ionize noble gases, such as Xe, Kr, or Ar. The laser system is based on a mode-locked Yb-fiber similariton oscillator in conjunction with a cladding-pumped chirped-pulse fiber amplifier. After recompression, 75 fs duration pulses at a 13.1 W average power are obtained. These pulses are then coherently added inside a passive ring cavity by controlling the fiber oscillator's pulse repetition rate and carrier-envelope offset frequency. This system is well suited for studying high-field phenomena at very high pulse repetition rates.     

Generation of 10-GHz duty-cycle tunable square optical pulse in an SOA-based mode-locked fiber laser

We demonstrate the generation of 10-GHz optical square pulses by injecting a picosecond pulse train into an SOA-based mode-locked fiber laser. The novel scheme exploits nonlinear effects and gain saturation phenomenon in the semiconductor optical amplifier (SOA). This technique uses gain-compression dynamics between the input pulses and the generated ones in gain-saturated SOA to form square pulses. The center wavelength of the generated optical square pulse can be tuned from 1530 to 1570 nm by adjusting the center wavelength of the optical band pass filter (OBPF) in the SOA-based mode-locked fiber ring laser. The duty cycle of the output pulse can be tuned from 12.7 to 88.4%, which strongly depends on the input power and intra-cavity power.