Simultaneous Determination of Four Active Components in a Compound Formulation by Liquid Chromatography

Summary A rapid and accurate LC method is described for simultaneous determination of pseudoephedrine hydrochloride (PSE), acetaminophen (AMP), dextromethorphen hydrobromide (DEX), and diphenhydramine hydrochloride (DPH) in a compound formulation. Chromatographic separation of the four drugs was achieved on a Hypersil CN column (150 mm × 4.6 mm, 5 m particle) by use of a mobile phase comprising a mixture of 3 mM ion-pairing solution, 2% aqueous triethylamine solution, and 2 M phosphoric acid, 68:48:88 (v/v), pH 3.0, delivered at 1.0 mL min^–1. Compounds were detected at 215 nm and the run time was less than 10 min. The linearity, accuracy, and precision of the method were found to be acceptable over the concentration ranges 6.1–36.4 g mL^–1 for PSE, 65.0–390.0 g mL^–1 for AMP, 3.1–18.6 g mL^–1 for DEX, and 5.0–30.0 g mL^–1 for DPH.     

Application of l-cysteine-capped nano-ZnS as a fluorescence probe for the determination of proteins

Nanometer-sized l-cysteine-capped ZnS particles have been synthesized and used as a fluorescence probe to investigate the effect of proteins on fluorescent intensity. With =190 nm, maximum and constant synchronous fluorescence enhancement was produced at 267 nm and pH 5.12 in the presence of proteins. A highly sensitive synchronous fluorescence method for the rapid determination of proteins has been developed. Under optimum conditions, calibration graphs are linear over the range 0.03–8.0 g mL^–1 for bovine serum albumin (BSA), 0.01–6.0 g mL^–1 for human serum albumin (HSA), 0.05–8.0 g mL^–1 for -globulin (-G), and 0.04–4.0 g mL^–1 for ovalbumin, respectively. The relative standard deviations of seven replicate measurements were 1.75% for 1.0 g mL^–1 BSA, 1.90% for 1.0 g mL^–1 HSA, 1.65% for 1.0 g mL^–1 -G, and 2.32% for 1.0 g mL^–1 ovalbumin.     

Development and validation of a novel HPLC/ELSD method for the direct determination of tobramycin in pharmaceuticals,plasma, and urine

A novel method for the direct determination of the aminoglycoside tobramycin was developed and validated based on reversed-phase high-performance liquid chromatography (RP-HPLC) with evaporative light scattering detector (ELSD). Using a Waters ODS-2 C18 Spherisorb column with an evaporation temperature of 45°C and nitrogen pressure of 3.5 bar, the selected mobile phase consisted of water/acetonitrile 55:45 containing 1.5 mL L^–1 HFBA (11.6 mM) in an isocratic mode at a rate of 1.0 mL min^–1. Tobramycins retention time was 4.3 min with an asymmetry factor of 1.7. A logarithmic calibration curve was obtained from 1 to 38 g mL^–1 (r > 0.9998). LOD was 0.3 g mL^–1; within-day %RSD was 1.0 (n = 3, 4.7 g mL^–1) and between-day %RSD was 1.1 (3 days within a week). The developed method was applied to the determination of tobramycin in a pharmaceutical crude substance and formulations (eye drops and ointments). Dilution experiments revealed the absence of interference from excipients (no constant and proportional errors); recovery from spiked samples was 99–103% with %RSD < 2.2 (n = 3×3). The developed HPLC/ELSD method was also found to be applicable in the determination of tobramycin in human plasma (0.6–12.5 g mL^–1) and urine (1.5–12.5 g mL^–1) after solid-phase extraction using carboxylate cartridges followed by solvent evaporation (×2 preconcentration). A mean recovery of 86% for plasma and 91% for urine was obtained.     

Determination of Dextromethorphan and Dextrorphan in Human Urine by High Performance Liquid Chromatography for Pharmacogenetic Investigations

The aim of the present study was to develop a sensitive method to measure dextromethorphan and dextrorphan in urine by HPLC to support pharmacogenetic studies in ethnic groups. Linearity was assessed in the range: 0.015–10 g mL^–1 for dextromethorphan and 1-10 g mL^–1 for dextrorphan. Inter and intra-day coefficients of variation were < 10%. Limits of detection and quantitation were 0.003 g mL^–1 and 0.015 g mL^–1 for dextromethorphan and 0.24 g mL^–1 and 1.0 g mL^–1 for dextrorphan, respectively. The method is reliable in helping determine the phenotype of Mexican ethnic groups using model drugs such as dextromethorphan.     

Characterization of airborne particulates by laser microprobe mass analysis

Summary Laser microprobe mass analysis (LAMMA) was applied to characterize aerosol particles collected and separated from 16m to 0.06m by a low pressure cascade impactor. Positive ion LAMMA spectra showed characteristic molecular peaks such as PbCl⁺, a series of Si₂O⁺–Si₂O₄ ⁺ and NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, and TiO⁺ in 0.06–0.12m, 0.5–1m and 4–8m fraction, respectively. In the negative ion LAMMA spectra, it was observed that the fragment peaks of sulfate ions were deficient above 2m and those of nitrate ions were deficient under 2m. LAMMA allows remarkable insights into the chemical nature of aerosol particles.

---

Charakterisierung luftgetragener Teilchen durch Laser-Microprobe-Massenspektrometrie

Zusammenfassung Laser-Microprobe-Spektrometrie (LAMMS) wurde zur Analyse atmosphärischen Aerosols herangezogen, welches im Korngrößenbereich zwischen 16m und 0.06m mit einem Niederdruckkaskadenimpaktor fraktioniert gesammelt wurde. Positive LAMMS-Spektren zeigten charakteristische molekulare Peaks, wie etwa PbCl⁺, eine Serie von Si₂O⁺–Si₂O₄ ⁺ und NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, sowie TiO⁺ in der 0,06–0,12-m,- 0,5–1–m- bzw. 4–8-m-Fraktion. In den negativen LAMMS-Spektren konnten über 2m keine Fragmentpeaks für Sulfationen, unter 2m. keine für Nitrationen beobachtet werden. LAMMS ermöglicht eine bemerkenswerte Einsicht in die chemische Natur von Aerosolteilchen.

     

New cobalt trimethylacetate complexes with pyridine

The reaction of the tetranuclear trimethylacetate complex Co₄(₃-OH)₂(-OOCCMe₃)₄(²-OOCCMe₃)₂(EtOH)₆ with pyridine in acetonitrile was studied. Two new compounds, viz., the hexanuclear cobalt(ii) complex Co₆py₄(₃-OH)₂(-OOCCMe₃)₁₀ (25% yield) and the unusual ionic compound [Co₃py₃(₃-O)(-OOCCMe₃)₆]⁺[Co₄py(₄-O)(-OOCCMe₃)₇]^– (5% yield), were prepared. The structures of the new compounds were established by X-ray diffraction analysis.     

LC Method for the Determination of Multiple Components in a Compound Cold Formulation

An isocratic liquid chromatographic method for determination of acetaminophen (AMP), caffeine (CAF), chlorphenamine maleate (CPM) and guaiacol glyceryl ether (GGE) in a compound cold formulation is described. Separation and quantitation were achieved on a Diamonsil C18 column using a binary mixture of methanol and 1.5% aqueous acetic acid (55: 45, v/v, pH 3.6) as mobile phase delivered at 0.4 mL min^–1. Single wavelength detection was at 220 nm for all four drugs and the run time was < 10 min. The linearity, accuracy and precision of the method were found to be acceptable over the concentration ranges: 16.0–127.8 g mL^–1 for AMP, 6.0–48.2 g mL^–1 for CAF, 5.0–40.0 g mL^–1 for CPM and 10.1–80.6 g mL^–1 for GGE.     

Simultaneous Determination of Pioglitazone and Glimepiride by High-Performance Liquid Chromatography

A rapid and accurate HPLC method has been developed for simultaneous determination of pioglitazone and glimepiride. Chromatographic separation of the two pharmaceuticals was performed on a Cosmosil C₁₈ column (150 mm × 4.6 mm, 5 m) with a 45:35:20 (v/v) mixture of 0.01 m triammonium citrate (pH adjusted to 6.95 with orthophosphoric acid), acetonitrile, and methanol as mobile phase, at a flow rate of 1.0 mL min^–1, and detection at 228 nm. Separation was complete in less than 10 min. The method was validated for linearity, accuracy, precision, limit of quantitation, and robustness [1, 2]. Linearity, accuracy, and precision were found to be acceptable over the ranges 2.50–30.00 g mL^–1 for pioglitazone and 0.10–10.00 g mL^–1 for glimepiride.     

Synthesis and Structure of the Complex [Mo3(μ3-S)(μ2-S2)3(Et2NCS2)3 +Br-

Tri-₂-disulfido-₃-thiotris(diethyldithiocarbamato)-S,S'-triangle-trimolybdenum bromide [Mo₃(₃-S)(₂-S₂)₃(Et₂NCS₂)₃ ⁺Br^- was obtained and characterized.     

Anwendung der Ringofenmethode zum Nachweis einiger Heteroelemente in organischen Verbindungen

Zusammenfassung Ein schnelles und einfaches Mikroverfahren zum Nachweis einiger Heteroatome organischer Verbindungen wurde entwickelt. Nach Aufschluß mit metallischem Kalium werden die entstehenden Ionen mit der Ringofenmethode getrennt und mit empfindlichen Reaktionen nachgewiesen. Nachweisgrenze: 0,5 bis 1g Stickstoff, 1 bis 2g Schwefel, 2 bis 3g Jod, 4 bis 5g Brom, 5 bis 10g Chlor in 0,5 bis 1 mg Einwaage.

---

Summary A rapid and simple micromethod was developed for the detection of several hetero-elements in organic compounds. After breaking down the sample with metallic potassium, the resulting ions are separated by the ring oven method and detected by means of sensitive reagents. Detection limits: 0.5 to 1g nitrogen, 1 to 2g sulfur, 2 to 3g iodine, 4 to 5g bromine, 5 to 10g chlorine in samples weighing 0.5 to 1 mg.

---

Résumé On a découvert un procédé à l'échelle micro, simple et rapide, pour rechercher certains hétéroéléments dans les composés organiques. Après mise en solution par le potassium métallique, on sépare les ions formés suivant la méthode du four annulaire et l'on effectue la recherche au moyen de réactions sensibles. Limite de dilution: 0,5 à 1g d'azote, 1 àg de soufre, 2 àg d'iode, 5 à 10g de chlore sur 0,5 à 1 mg de prise d'essai.

     

Development of a competitive liposome-based lateral flow assay for the rapid detection of the allergenic peanut protein Ara h1

A competitive lateral flow assay for detecting the major peanut allergen, Ara h1, has been developed. The detector reagents are Ara h1-tagged liposomes, and the capture reagents are anti-Ara h1 polyclonal antibodies. Two types of rabbit polyclonal antibodies were raised either against the entire Ara h1 molecules (anti-Ara h1 Ab) or against an immunodominant epitope on Ara h1 (anti-peptide Ab). All of them reacted specifically with Ara h1 in Western Blot against crude peanut proteins. Moreover, the anti-Ara h1 Ab was chosen for this assay development because of its highest immunoactivity to Ara h1-tagged liposomes in the lateral flow assay. The calculated limit of detection (LOD) of this assay is 0.45 g mL^–1 of Ara h1 with a dynamic range between 0.1 and 10 g mL^–1 of Ara h1 in buffer. Additionally, the visually determined detection range is from 1 to 10 g mL^–1 of Ara h1 in buffer. Results using this assay can be obtained within 30 min without the need of sophisticated equipment or techniques; therefore, this lateral flow assay has the potential to be a cost-effective, fast, simple, and sensitive method for on-site screening of peanut allergens.     

Platinum concentration in silicone breast implant material and capsular tissue by ICP-MS

Inductively coupled plasma-mass spectrometry (ICP-MS) was used to determine the concentration of platinum (Pt) in silicone breast implant gel (range, 0.26–48.90 g g^–1 Pt; n=15), elastomer (range, 3.05–28.78 g g^–1 Pt; n=7), double lumen (range, 5.79–125.27 g g^–1 Pt; n=7), foam (range, 5.79–8.36 g g^–1 Pt; n=2), and capsular tissue (range, 0.003–0.272 g g^–1 Pt; n=15). The results show that very high levels of Pt are present in the encasing elastomer, double lumen, and foam envelope materials. Silicone breast implants can be a source of significant Pt exposure for individuals with these implants.     

The oxidative addition of diphenylphosphine and monophenylphosphine to the electron-rich rhenium-rhenium triple bond. The isolation and characterization of compounds that contain the four-center Re(μ-X)(μ-PR2)Re cluster (X=halide)

Diphenylphosphine oxidatively adds to the ReRe bonds of Re₂ X ₄(-dppm)₂ (X=Cl or Br; dppm=Ph₂PCH₂PPh₂) and Re₂Cl₄(-dpam)₂ (dpam=Ph₂AsCH₂AsPh₂) to afford the dirhenium(III) complexes Re₂(-X)(-PPh₂)HX ₃(-LL)₂. The dppm complexes have also been prepared from the reactions of Re₂(-O₂CCH₃)X ₄(-dppm)₂ with Ph₂PH, and a similar strategy has been used to prepare Re₂(-Cl)(-PPh₂)HCl₃(-dmpm)₂ (dmpm=Me₂PCH₂PMe₂) from Re₂(-O₂CCH₃)Cl₄(dmpm)₂. Phenylphosphine likewise reacts with Re₂ X ₄(-dppm)₂ to give Re₂(-X)(-PHPh)HX ₃(-dppm)₂. An X-ray crystal structure determination on Re₂(-Cl)(-PPh₂)HCl₃(-dppm)₂ confirms its edge-shared bioctahedral structure. This complex crystallizes in the space group (No. 148) witha=21.699(3) Å, =84.50(4)°,V=10084(5) ų, andZ=6. The structure was refined toR=0.049 (R _w 0.069) for 5770 data withI>3.0(I). The Re-Re distance is 2.5918(7) Å. Oxidation of the bromide complex Re₂(-Br)(-PPh₂)HBr₃(-dppm)₂ with NOPF₆ produces the unusual dirhenium(III, II) cation [Re₂(-H)(-Br)[P(O)Ph₂]Br₂(NO)(-dppm)₂]⁺ which has been structurally characterized as its perrhenate salt, [Re₂(-H)(-Br)[P(O)Ph₂]Br₂(NO)(-dppm)₂]ReO₄ · 2CH₂Cl₂. This complex crystallizes in the space group (No. 2) witha=14.187(7) Å,b=16.419(5) Å,c=16.729(5) Å, =98.76(2)°, =110.11(3)°, =104.66(3)°,V=3414(6) ų,Z=2. The structure was refined toR=0.040 (R _w =0.051) for 5736 data withI>3.0(I). The presence of a phosphorus-bound [P(O)Ph₂]^– ligand, a linear nitrosyl and a bridging hydrido ligand has been confirmed. The Re-Re distance is 2.6273(8) Å.     

The use of temperature to simplify formose sugar composition

Form ose reaction, the Ca(OH)₂ catalyzed condensation of HCHO to a complex mixture of sugars, does not lose its autocatalytic nature at 98°C. The induction period is 15 sec, and then, at 18% total HCHO conversion, there was a period of approximately 3 sec duration in which the reaction had produced C₆ sugars at 84.3 wt.% selectivity. Glucose amounted to 90% of those sugars, and no branched sugars were detected. Conversion was complete within 3 min. The simple nature of the product was lost at lower temperatures or higher conversions.

---

— HCHO, Ca(OH)₂, 98°C. 15 , 38%- HCHO 3 , C₆ 84,3 . %. 90%, . 3- . .

     

Determination of 6-amino-2,2-dimethyl-1,3-dioxepan-5-ol by postcolumn derivatization witho-phthalaldehyde/2-mercapto-ethanol after ion-pair chromatography

Summary A high-performance liquid chromatographic method is discribed for the determination of 6-amino-2,2-dimethyl-1,3-dioxepan-5-ol using Spherisorb ODS II stationary phase and mobile phase 30:70 (v/v) methanol: aqueous 1-octane sulfonic acid. Detection was fluorimetric following postcolumn derivatization with o-phthaladehyde/2-mercaptoethanol. The procedure was applied to the analysis of aqueous solutions and microcrystalline suspensions in liquid paraffin, prepared for investigation of the toxicological profile. The method was validated for selectivity, linearity of detector response, repeatability, limit of detection and quantitation. The HPLC method was selective. The instrumental limit of detection was 0.5 ng per injection (0.05 g mL^–1). The method detection limits were 0.5 g mL^–1 aqueous solution and 5 g mL^–1 liquid paraffin suspension, the quantitation limit 0.05 mg mL^–1 aqueous solution and 1.0 mg mL^–1 liquid paraffin. Linearity was within 0.94–47.1 g mL^–1. Intra-assay accuracy accounted for 99–100% in the range 0.05–226 mg mL^–1 aqueous solution, intra-assay precision for 2% (C.V.). For microcrystalline liquid paraffin suspensions with 1 and 250 mg mL^–1 99 and 109% was found for intra-assay accuracy. Intra-assay precision was 5% (C.V.). Reliable results over a wide concentration range can be obtained. The procedure is considered valid for determination of the analyte in aqueous solution or microcrystalline paraffin oil suspensions.     

Thermal behaviour of acidic salts of mixed tetravalent metals

The results of investigations on intercalated crystalline zirconium phosphate are described in the literature. The behaviour of crystalline phosphates containing both zirconium and titanium metal ions has not been investigated previously. Within these investigations, the thermal behaviour of such materials has been studied in the temperature interval 25–1000 °C by simultaneous recording of TG, DTG and DTA curves. The results are presented in this paper.

---

Zusammenfassung Ergebnisse über Untersuchungen an in Schichten eingelagerten kristallinen Zirkoniumphosphat sind in der Literatur beschrieben. Das Verhalten kristalliner Phosphate, die sowohl Zirkoniumals auch Titanmetallionen enthalten, wurde bis jetzt nicht untersucht. Als Teil dieser Untersuchungen wurde das thermische Verhalten solcher Materialien im Temperaturbereich 25–1000 °C durch simultanes Registrieren der TG-, DTG- und DTA-Kurven näher bestimmt, dessen Ergebnisse hier dargelegt werden.

---

. , . , , 25–1000°. .

     

Chemical behaviour of helium muonide just after muon catalyzed fusion

Chemical behaviour of a helium muonide atom /He^o/ can be understood on the analogy of its hydrogen homologues, muonium /Mu/, deuterium /D^o/ and tritium /T^o/. In muon catalyzed fusion /CF/, a small fraction of negative muon in the fusion cycle sticks to helium to give proton-like He⁺ which easily picks up one electron forming He^o. The energy of He⁺ at birth is about 3.5 MeV being in a similar situation to the case of a hot tritium atom produced by /n, p/ or /n, / reaction. The reaction cross section and rate of He^o reactions are estimated.     

Fallout analysis of atmospheric water precipitations

Summary A rapid ion-exchange method for the determination of ¹⁴⁴Ce, ¹³⁷Cs, ⁸⁹Sr, ⁹⁰Sr and ¹⁴⁰Ba in 2–30 liter samples of atmospheric water precipitations is described. The samples, containing up to 300 mg of calcium, are sorbed on a specially shaped column filled with Dowex 50, X-8 or Dowex 50W, X-8. Radio-cerium and radio-caesium are stripped from the column with 0.6 M ammonium glycolate/ 0.2 M NaCl, pH 5, radio-strontium and radio-barium with 0.15 M ammonium citrate, pH 7.5. The isolated radio-nuclides are counted on a low-background beta-counter: ¹⁴⁴Ce as CeO₂, ¹³⁷Cs as Cs-dipicrylaminate, ⁸⁹Sr/⁹⁰Sr as SrCO₃, ⁹⁰Y as Y₂O₃, and ¹⁴⁰Ba as BaCO₃. The mean chemical yields amount to 95% for cerium, 85% for caesium, 95% for strontium, 95% for yttrium and 65% for barium. With parallel determinations at levels of a few picocuries, the deviations of the results from the respective mean values generally do not exceed ± 5%. With a 30 l sample the limit of detection amounts to 0.005 Ci/l for ¹⁴⁴Ce, 0.006 Ci/l for ¹³⁷Cs, 0.005 Ci/l for ⁹⁰Sr, and 0.006 Ci/l for ¹⁴⁰Ba.

---

Zusammenfassung Es wird eine schnelle Ionenaustauschmethode für die Bestimmung von ¹⁴⁴Ce, ¹³⁷Cs, ⁸⁹Sr, ⁹⁰Sr und ¹⁴⁰Ba in 2–30 l Proben von atmosphärischen Wasser-Niederschlägen beschrieben. Die Proben, mit einem Calciumgehalt bis zu 300 mg, werden in eine besonders gestaltete, mit Dowex 50, X-8 oder Dowex 50 W, X-8 gefüllte Säule eingewaschen. Radio-Cer und Radio-Caesium werden mit 0,6 M Ammoniumglykolat/0,2 M NaCl, pH 5, Radio-Strontium und Radio-Barium mit 0,15 M Ammoniumcitrat pH 7,5 eluiert. Die isolierten Radio-Nuklide werden in einem Beta-Antikoinzidenzzähler gemessen: ¹⁴⁴Ce als CeO₂, ¹³⁷Cs als Cs-dipikrylaminat, ⁸⁹Sr/⁹⁰Sr als SrCO₃, ⁹⁰Y als Y₂O₃ und ¹⁴⁰Ba als BaCO₃. Die mittlere Rückgewinnung der zugesetzten Träger beträgt für Cer 95%, 85% für Caesium, 95% für Strontium, 95% für Yttrium und 65% für Barium. In Parallelbestimmungen mit Gehalten von einigen Ci/l, überschreiten die Abweichungen der Ergebnisse von den entsprechenden Mittelwerten im allgemein nicht 5%. Bei einer 30 l-Probe beträgt die untere Nachweisgrenze 0,005 Ci/l für ¹⁴⁴Ce, 0,006 Ci/l für ¹³⁷Cs, 0,005 Ci/l für ⁹⁰Sr und 0,006 Ci/l für ¹⁴⁰Ba.

     

Fluoridbestimrnung in Wasser und Luft mit ionenselektiven Elektroden

Zusammenfassung Systematische Bestimmungen des Fluoridgehaltes in verschiedenen Wasserproben aus Serbien und in Luftproben aus einigen In-dustriegebieten und aus der Stadt Belgrad wurden durchgeführt. Außerdem wurde der Fluoridgehalt in einigen meistkonsumierten Mineralwässern aus alien Territorien Jugoslawiens geprüft. Etwa 600 Proben wurden analysiert. Die Ergebnisse sollen für die kartographische Erfassung der Verteilung von Fluor im Trinkwasser dienen.

---

Determination of fluoride in Yugoslavian air and water with an ion-sensitive electrode

Summary Fluoride has been measured in over 600 samples of air and water with an ion-sensitive electrode. The concentrations found in the air samples were 1.6–l08g/m³ for industrial areas, 1.9–25.6g/m³ for urban areas and 1.1–18.4g/m³ for rural areas. Most of the samples had fluoride levels below 20g/m³3. The concentrations found in water samples were 0.12–0.34g/litre for drinking water and 0.27–5.6g/litre, for mineral waters.

     

Addition of HCl to a Cluster-Bound Vinylidene Ligand: Preparation and Structure of Ru5(μ3-SMe)(μ3-CMe)(μ-Cl)(μ-SMe)(μ-PPh2)2(CO)9·PhMe

Addition of aqueous HCl to Ru₅( ₃-C=CH₂)(-SMe)₂(-PPh₂)₂(CO)₁₀ afforded the structurally characterized carbyne complex Ru₅( ₃-SMe)( ₃-CMe)(-Cl)(-SMe)(-PPh₂)₂(CO)₉, formed by addition of H to the vinylidene ligand; a Cl atom bridges an Ru–Ru bond.