Optimisation of supercritical fluid extraction of polynuclear aromatic hydrocarbons from spiked soil and marine sediment standard reference material

 For the determination of 16 PAHs in soils and sediment samples by GC/FID and GC/MS, the dynamic off-line supercritical fluid extraction with both pure and modified carbon dioxide has been evaluated. The optimisation of extraction parameters was performed for four individual groups of PAHs according to their number of aromatic rings (2–3 rings, 4 rings, 5 rings and 6 rings) by varying pressure (200–510 bar), temperature (50–150 °C), extraction fluid volume (10–50 ml), and the methanol modifier concentration (0–10%). Using a five level spherical factorial experimental design the number of experiments required for optimisation was 45. In spiked soil samples extraction efficiencies of 80–100% were achieved for the individual groups of PAHs. At the optimal set of conditions 10–30% lower recoveries of PAHs were obtained for the standard reference material NIST SRM 1941a (marine sediment). The largest differences between extraction recoveries of native and spiked PAHs occurred at high molecular weight PAHs. Using SFE efficiency data for the standard reference material, cluster analysis proved that dividing the 16 PAHs into four groups according to their number of aromatic rings was appropriate and correct. Received: 2 February 1996/Revised: 26 November 1996/Accepted: 30 November 1996     

An evaluation of analytical quality for selected PAH measurements in a fuel-contaminated soil

The measurements of polycyclic aromatic hydrocarbons (PAHs) in soil require optimized analytical methods that assess reliable mass fraction results. This is particularly important for analysing very complex matrix such as contaminated soils with crude fuels. The main objectives of this work were focused to minimize analytical effort and assess result reliability in analysis of PAH by high-performance liquid chromatography with fluorescence detection (HPLC/FD). First, analysis of soil samples with/without fuel contamination was well established by sonication (US) and pressurized fluid extraction (ASE) using minimal amount of sample and minimal treatment of sample. On the other hand, an extensive study with spiked and field soil samples was performed by checking proportional and constant bias for analytical validation. The major components for estimating uncertainty contributions were evaluated on the basis of intermediate precision with two fuel matrix, PAH mass fraction and dates of analyses.     

Comparison of immunoassay and gas chromatography-mass spectrometry for measurement of polycyclic aromatic hydrocarbons in contaminated soil

Polycyclic aromatic hydrocarbons (PAHs) are frequently encountered in the environment and may pose health concerns due to their carcinogenicity. A commercial enzyme-linked immunosorbent assay (ELISA), was evaluated as a screening method for monitoring PAHs at contaminated sites. The ELISA was a carcinogenic PAH (C-PAH) RaPID assay testing kit that cross-reacts with several PAHs and utilizes benzo[a]pyrene (BaP) as a calibrator. Soil samples were extracted with 50% acetone in dichloromethane (DCM) for analysis by ELISA and gas chromatography-mass spectrometry (GC-MS). The overall method precision was within ±30% for ELISA and within ±20% for GC-MS. Recovery data for spiked soils ranged from 46 to 140% for BaP as determined by ELISA. Recoveries data of the GC-MS surrogate standards, 2-fluorobiphenyl and chrysene, were greater than 70%. The GC-MS procedure detected a total of 19 priority PAHs (2-6-ring PAHs) including seven probable human carcinogens (4-6-ring B2-PAHs). The ELISA results were compared to GC-MS summation results for the total 19 target PAHs as well as for the subset of the seven B2-PAH compounds. For all soil samples, the PAH concentrations derived from ELISA were greater than the sum of B2-PAH concentrations obtained by GC-MS. ELISA determinations were also frequently greater than the results obtained by GC-MS for the total 19 PAH compounds. This discrepancy can be expected, since the ELISA is a screening assay for the detection of several related PAHs while the GC-MS procedure detects priority PAH compounds. Thus, only a subset of PAHs (e.g. 19 PAHs) in the soil samples were measured by GC-MS while additional PAHs, including alkylated PAHs, and PAH derivatives have been demonstrated to be cross-reactive in the C-PAH ELISA. Results of paired tests show that the PAH data from ELISA and GC-MS methods are significantly different (P<0.001), but highly correlated. The ELISA data had a strong positive relationship with the GC-MS summation data for the B2-PAHs as well as for the 19 PAHs targeted by the GC-MS method. Results indicate that the ELISA may be useful as a broad screen for monitoring PAHs in environmental samples.     

加速溶剂萃取-固相萃取净化-气相色谱/质谱法测定土壤中的多环芳烃

建立了加速溶剂萃取-固相萃取净化-气相色谱/质谱法同时测定土壤中16种多环芳烃的方法.土壤样品经正己烷-丙酮提取,经无水Na2SO4脱水、氮吹浓缩后,弗罗里土小柱净化,采用气相色谱/质谱检测,内标法定量.结果表明:该方法在质量浓度0.4～10 μg/mL范围内线性良好,相关系数(r2)大于0.9962,检出限为4.8～...     

Quantitative determination of 16 polycyclic aromatic hydrocarbons in soil samples using solid‐phase microextraction

A method for the determination of polycyclic aromatic hydrocarbons (PAHs) in soil samples using ultrasonic‐assisted extraction with internal surrogates combined with solid‐phase microextraction and GC‐MS has been developed. Five kinds of commercial solid‐phase microextraction fibers, 100 μm PDMS, 30 μm PDMS, 65 μm PDMS/DVB, 50 μm DVB/CAR/PDMS and 85 μm PA, were compared to choose the optimal SPME fiber for extraction of PAHs. One hundred micrometers of PDMS fiber was found to be more suitable for the determination of PAHs due to its wider linear range, better repeatability, lower detection and more satisfactory efficacy than the other fibers. Under the recommended conditions, 100 μm PDMS fiber could provide low nanogram level detection limits with correlation coefficient greater than 0.98. The method was also applied to determine PAHs in a spiked soil sample, obtaining recoveries higher than 79.3%. A field study with naturally contaminated samples from local contaminated sites was carried out. The proposed method was found to be a reliable, inexpensive and simple preparation method for quantitative determination of 16 PAHs in soil samples.     

Liquid chromatographic/mass spectrometric determination of desmedipham and phenmedipham and their metabolites in soil

A simple method is described for the simultaneous determination of residues of 2 carbamate herbicides (phenmedipham and desmedipham) and related metabolites (m-aminophenol, aniline, and m-toluidine) in soil. The analytes are extracted from spiked soils with methanol. The solvent/soil suspension is centrifuged, and the supernatant is directly injected, without any further cleanup, into a reversed-phase liquid chromatography/mass spectrometry apparatus equipped with a TurbolonSpray interface. The method was tested on 5 soils having different physicochemical properties. Recoveries from the soil types, spiked over the range of 50-200 ppb, were essentially quantitative for each analyte. The detection limits of the method are < or = 25 ng/g.     

超声-微波协同萃取装置用于土壤中多环芳烃的分析

本研究将开放式微波和直接超声波振荡两种不同的能量方式相结合,研制出超声-微波协同萃取装置。通过萃取土壤中微量多环芳烃(PAHs),对方法和仪器的可行性进行了初步评价。结果表明,在60 mL二氯甲烷-正已烷(1∶1,V/V)的混合萃取剂,100 W微波辐射功率(超声振动功率固定为50 W),萃取9~10m in,土壤中多环芳烃回收率达86.6%,相对标准偏差约4.0%。与索氏抽提、高压密闭和开放式微波等萃取方法相比,本方法具有样品容量大,萃取时间短,萃取效率受样品中含水量和溶剂极性影响小等优点。     

Systematic study of the influence of modifiers on the CO2-supercritical extraction of PAHs in soil

Summary An exhaustive study of the behaviour in supercritical fluid extraction of eight PAHs in real samples of soil compared to spiked samples in silica has been carried out. The presence of a modifier is mandatory for quantitative extraction of the native analytes, but is unnecessary in spiked samples. The type and volume of modifier to be added and the sample-modifier contact time were optimized and the influence of the particle size assessed.     

On the semi-quantification of polycyclic aromatic hydrocarbons in contaminated soil by an enzyme-linked immunosorbent assay kit

Polycyclic aromatic hydrocarbons (PAHs) are of environmental concern, for instance when found in contaminated soils at sites where industrial activities have occurred. For efficient screening of such soils, the commercially available enzyme-linked immunosorbent assay (ELISA) kit, the PAH RIS^c® soil test, can be used. However, the site-specific performance may vary due to differences in soil properties and contamination profiles. Hence, in this study we have examined various contributing factors to the total ELISA measurements uncertainties. These factors include contributions from co-extracted (non-target) compounds, the extraction efficiency and differences in cross-reactivity among the target analytes. Reference values were obtained through pressurized liquid extraction (PLE) and gas chromatography coupled to mass spectrometry (GC-MS) analysis. The results showed that the ELISA does not seem to respond to non-target compounds in the soil extracts to any large extent. Furthermore, high molecular weight PAHs were found to be more efficiently extracted with PLE than with methanol agitation, which is used for ELISA. If this, and the cross-reactivity of the individual PAHs, were taken into consideration, the ELISA and GC-MS results were in good agreement.     

Rapid aryl hydrocarbon receptor based polymerase chain reaction screening assay for polychlorinated dibenzo-p-dioxins and furans in soil and sediment

A method for the estimation of polychlorinated dibenzo-p-dioxin and furan (PCCD/F) toxicity equivalent quotient (TEQ) of soil and sediment matrices is described. The method includes extraction, isolation of the PCDD/Fs from interfering compounds, such as polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs), and measurement of PCDD/F using the PROCEPT aryl hydrocarbon (AhR) receptor based polymerase chain reaction (PCR) assay. The values obtained using the PROCEPT assay correlate well with reference TEQ values generated from gas chromatography-high resolution mass spectrometry (GC-HRMS), with a linearity coefficient (R(2)) of 0.94. Applied in a screening mode at 50pg/g PCDD/F TEQ, the PROCEPT assay yielded five false positive results (2.6%) and no false negative results for 196 analyses of spiked soils and environmental samples obtained from US EPA Superfund sites.     

Rapid assessment of the impact of microwave heating coupled with UV-C radiation on the degradation of PAHs from contaminated soil using FTIR and multivariate analysis

The presence and fate of polyaromatic hydrocarbons (PAHs) in the environment are receiving a great concern. In this study, three oil-contaminated soils (industrial area, Dukhan city, and artificial soils) were utilized to examine the effect of microwave (MW) heating and UV-C irradiation on the PAHs degradation. A rapid assessment of the impact was evaluated using Fourier transform infrared (FTIR) and multivariate analysis. The total organic matter values for the maximum PAHs reduction were evaluated based on the FTIR spectra of the contaminated soils followed with the principal component analysis (PCA). The results showed that the highest total organic carbon reduction was achieved for the industrial soil sample that required a high MW power and long MW exposure time. On the other hand, the Dukhan city soil sample, which has the lowest total organic carbon, required a high MW power and short MW exposure time followed by UV-C treatment for 20 min to reach the maximal FTIR transmittance reduction. The cluster analysis was also used to evaluate the impact of MW heating, and MW heating followed by UV-C irradiation on the degradation of PAHs. The PCA results of the industrial city sample showed that neither MW treatment (100% MW, 15 min exposure time) followed by UV-C treatment for 20 min nor 10 min is significantly different from the MW treatment (100% MW, 15 min exposure time). However, for the Dukhan sample, the UV-C treatment at 10 min after high MW power and long exposure time (100% MW, 15 min exposure time) was the most efficient treatment.     

Micelle formation for improvement of continuous subcritical water extraction of polycyclic aromatic hydrocarbons in soil prior to high-performance liquid chromatography-fluorescence detection

A new method for the extraction-individual separation-determination of polycyclic aromatic hydrocarbons (PAHs) in soil is reported. The method is based on the integration of three steps: continuous subcritical extraction, solid-phase clean-up/preconcentration, and HPLC separation with post-column fluorimetric determination. Sodium dodecyl sulfate (SDS) was added to the water for favouring the extractability of the low-polarity analytes. Soil samples spiked with the target PAHs were subjected to static-dynamic extraction with SDS-water at 50 bar, 150 degrees C, for 15 min of static extraction and 10 min dynamic extraction at a flow-rate of 3 ml/min. Recoveries from 73.6 to 110.4% were obtained in the presence of SDS versus 30 to 80% obtained with water as extractant. The calibration graphs provided by HPLC-fluorimetric detection were run between 0.031 and 0.375 microg/ml for each analyte with regression coefficients between 0.917 and 0.999 and precision, expressed as RSD, between 1.2 and 11.5%. The method was applied to a certified reference material [CRM 524, BCR (Community Bureau of Reference), industrial soil/organic] for validation and the results obtained were in agreement with the certified values.     

Influence of the soil matrices on the analytical performance of headspace solid-phase microextraction for organotin analysis by gas chromatography-pulsed flame photometric detection

Organotin compounds (OTCs) have been identified in a variety of environmental media (air, surface water, groundwater, soil and sediments). In the past, much attention was assigned to the study of the OTCs content in biological samples, water and sediments. Little information about OTCs in soil is available. In this work, a procedure for butyl and phenyltin determination in soils by headspace-solid-phase microextraction (HS-SPME) gas chromatography-pulsed flame photometric detection (GC-PFPD) was investigated. For SPME analysis, a polydimethylsiloxane (PDMS) coating was applied. Peat soil rich in organic matter and with a high cation-exchange capacity (CEC), and clay soil low in organic matter and with a low CEC were analysed. The influence of these different soil matrices on HS-SPME analysis was evaluated by spiking of samples. In general, the recoveries for the two spiked soils exceeded 80%. The repeatability of the method was better than 10%. The limits of detection (LODs) and limits of quantification (LOQs) were in the ng S ng(-1) range. The technique may be reliably applied for the determination of butyltins and monophenyltin in soils, while it shows some limitations for the analysis of di- and triphenyltin (TPhT).     

Determination of cyclic and linear siloxanes in soil samples by ultrasonic-assisted extraction and gas chromatography-mass spectrometry

A rapid method, based on sonication-assisted extraction in small columns (SAESC) and subsequent quantification and identification by gas chromatography-mass spectrometry (GC-MS), was developed for the determination of cyclic and linear siloxanes in soil. In the experiments with spiked samples (10-50 ng g(-1)), the recovery of cyclic and linear siloxanes ranged from 87.7 to 108.0% and from 84.9 to 107.6%, respectively. The validated method was used to determine the levels of these compounds in various types of soil samples collected from different locations in Spain. The cyclic siloxanes, decamethylcyclopentasiloxane (D5) and dodecamethylcyclohexasiloxane (D6) were detected in all the soil samples analyzed at concentrations from 9.2 to 56.9 ng g(-1) for D5 and from 5.8 to 27.1 ng g(-1) for D6 in agricultural soils and from 22 to 184 ng g(-1) for D5 and from 28 to 483 ng g(-1) for D6 in industrial soils. The total linear siloxanes concentrations (L5-L14) (sum of the 10 congeners) ranged from 191 to 292 ng g(-1) in agricultural soils and from 1411 to 8532 ng g(-1) in industrial soils.     

磁性微孔聚合物富集/表面增强拉曼光谱法测定水与土壤中多环芳烃

建立了磁性聚亚苯基共轭微孔聚合物富集/表面增强拉曼光谱法测定水样和土壤中4种多环芳烃的分析方法。待测物经磁性聚亚苯基共轭微孔聚合物吸附萃取,甲醇洗脱后进行SERS检测。结果表明,蒽、芘、荧蒽和苯[α]芘在0.1~10μg/L范围内与其SERS特征峰峰强呈良好的线性关系,检出限为0.03μg/L,回收率为71.6%~115.8%,相对标准偏差不大于13.7%。该分析方法灵敏度高,能够满足实际水样和土壤中4种多环芳烃同时检测的要求。     

Analysis of DDT residues in soil by ELISA: an international interlaboratory study

An international interlaboratory study was conducted to determine the performance of a group of laboratories from developing and developed countries. The study used a commercial microwell ELISA on unknown samples spiked with different levels of DDT. The study design was based on Youden pairs and balanced replicates. Two soils, differing in particle size distributions, organic matter content, and cation-exchange capacities and thought to be DDT-free, were spiked at 5 DDT levels between 0.025 and 2 mg/kg. Nineteen laboratories in 17 countries took part in the collaborative trial; of these, the majority were modestly equipped laboratories in developing countries. Samples were analyzed without filtration or cleanup and using standards of pure DDT in methanol. Data were analyzed for repeatability and reproducibility, and average recoveries at the spike levels were calculated. Mean real recoveries for both soils were similar (103% for soil A and 100% for soil B), with values between 0.1 and 2 mg/kg DDT. Precision estimates were best in the linear working range of the assay (0.1-0.5 mg/kg DDT), with reproducibility relative standard deviations (RSDR) typically averaging about 38 and 46% near the upper and lower detection limits, respectively. Corresponding repeatability relative standard deviation (RSDr) values were 20-36% and 36-57%. Thus, even though much of the trial was performed under developing country conditions, performance statistics were similar to other reported results obtained with ELISAs on small molecules of agricultural importance, such as mycotoxins and pesticide and antibiotic residues.     

Vacuum-assisted headspace solid phase microextraction of polycyclic aromatic hydrocarbons in solid samples

For the first time, Vacuum Assisted Headspace Solid Phase Microextraction (Vac-HSSPME) is used for the recovery of polycyclic aromatic hydrocarbons (PAHs) from solid matrices. The procedure was investigated both theoretically and experimentally. According to the theory, reducing the total pressure increases the vapor flux of chemicals at the soil surface, and hence improves HSSPME extraction kinetics. Vac-HSSPME sampling could be further enhanced by adding water as a modifier and creating a slurry mixture. For these soil-water mixtures, reduced pressure conditions may increase the volatilization rates of compounds with a low K_H present in the aqueous phase of the slurry mixture and result in a faster HSSPME extraction process. Nevertheless, analyte desorption from soil to water may become a rate-limiting step when significant depletion of the aqueous analyte concentration takes place during Vac-HSSPME. Sand samples spiked with PAHs were used as simple solid matrices and the effect of different experimental parameters was investigated (extraction temperature, modifiers and extraction time). Vac-HSSPME sampling of dry spiked sand samples provided the first experimental evidence of the positive combined effect of reduced pressure and temperature on HSSPME. Although adding 2 mL of water as a modifier improved Vac-HSSPME, humidity decreased the amount of naphthalene extracted at equilibrium as well as impaired extraction of all analytes at elevated sampling temperatures. Within short HSSPME sampling times and under mild sampling temperatures, Vac-HSSPME yielded linear calibration curves in the range of 1–400 ng g⁻¹ and, with the exception of fluorene, regression coefficients were found higher than 0.99. The limits of detection for spiked sand samples ranged from 0.003 to 0.233 ng g⁻¹ and repeatability from 4.3 to 10 %. Finally, the amount of PAHs extracted from spiked soil samples was smaller compared to spiked sand samples, confirming that soil could bind target analytes more strongly and thus decrease the readily available fraction of target analytes.     

A novel headspace solid-phase microextraction method for the exact determination of organochlorine pesticides in environmental soil samples

A novel method of determining organochlorine pesticides (OCPs) is described. It is based on solid-phase microextraction (SPME) and gas chromatography–electron capture detection. During the development of the method, soil samples were prepared, spiked with standard solution, and then aged for some time. Extraction conditions such as the extraction time, the NaCl content, the volume of water, the extraction temperature and the desorption time were investigated and optimized. The limits of detection obtained using the method ranged from 0.10 to 0.51 ng g⁻¹, and relative standard deviations were lower than 10% for most organochlorine pesticides. Real soil samples were successfully analyzed using the proposed method. The results from the method developed here were in good agreement with those obtained using ultrasonic extraction. The result demonstrates that aging soils spiked with standard solution is an important method development step, because the soil samples obtained using this approach are more like real soils than those obtained when aging is not used.      

Determination of nitroaromatic, nitramine, and nitrate ester explosives in soil by gas chromatography and an electron capture detector

Hazardous waste site characterization, forensic investigations, and land mine detection are scenarios where soils may be collected and analyzed for traces of nitroaromatic, nitramine, and nitrate ester explosives. These thermally labile analytes are traditionally determined by high-performance liquid chromatography (HPLC); however, commercially available deactivated injection port liners and wide-bore capillary columns have made routine analysis by gas chromatography (GC) possible. The electron-withdrawing nitro group common to each of these explosives makes the electron capture detector (ECD) suitable for determination of low concentrations of explosives in soil, water, and air. GC-ECD and HPLC-UV concentration estimates of explosives residues in field-contaminated soils from hazardous waste sites were compared, and correlation (r>0.97) was excellent between the two methods of analysis for each of the compounds most frequently detected: 2,4,6-trinitrotoluene (TNT), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), 2,4-dinitrotoluene (2,4-DNT), 1,3-dinitrobenzene (1,3-DNB), 1,3,5-trinitrobenzene (TNB), and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX). The analytes were extracted from soils with acetonitrile by 18 h of sonication in a cooled ultrasonic bath. Two soil-to-solvent ratios were evaluated: 2.00 g:10.00 ml and 25.0 g:50.0 ml. GC-ECD method detection limits were similar for the two soil-to-solvent ratios and were about 1 mug kg(-1) for the di- and trinitroaromatics, about 10 mug kg(-1) for the mono-nitroaromatics, 3 mug kg(-1) for RDX, 25 mug kg(-1) for HMX, and between 10 and 40 mug kg(-1) for the nitrate esters (nitroglycerine [NG] and pentaerythritol tetranitrate [PETN]). Spike recovery studies revealed artifacts introduced by the spiking procedure. Recoveries were low in some soils if the amount of soil spiked was large (25.0 g) compared to the volume of spike solution added (1.00 ml). Recoveries were close to 100% when 2.00-g soil samples were spiked with 1.00 ml of solution. Analytes most frequently found in soils collected near buried land mines were the microbial transformation products of TNT (2-amino-4,6-dinitrotoluene [2-Am-DNT] and 4-amino-2,6-dinitrotoluene [4-Am-DNT]), manufacturing impurities of TNT (2,4-DNT, 2,6-DNT, and 1,3-DNB), and TNT. The microbial reduction products of the isomers of DNT and of 1,3-DNB were also detected, but the ECD response to these compounds is poor.     

Analysis of polycyclic aromatic hydrocarbons in contaminated soil by Curie point pyrolysis coupled to gas chromatography-mass spectrometry, an alternative to conventional methods

Curie point pyrolysis gas chromatography-mass spectrometry (Py-GC-MS) has been compared with classical extraction procedures (Soxhlet, sonication, KOH digestion, microwave-assisted) followed by GC-MS analysis for the determination of polycyclic aromatic hydrocarbons (PAHs) in contaminated soil. In each case, the efficiency of the technique was examined for 16 PAHs included in the US Environmental Protection Agency Priority Pollutant List. The results indicate that the recovery of PAHs is dependent on the extraction technique. The highest recoveries of PAHs were obtained with Curie point pyrolysis and KOH digestion. Py-GC-MS appeared to be interesting alternative method for the determination of PAHs in contaminated soil. The results were validated by certified soil (CRM 104) analysis.