Determination of dioxopromethazine hydrochloride by capillary electrophoresis with electrochemiluminescence detection

The paper presents a rapid method for the determination of dioxopromethazine hydrochloride (DPZ), an antihistamine drug, by the capillary electrophoresis with electrochemiluminescene detection (CE–ECL) using tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) reagent. This CE–ECL detection method has high sensitivity, good selectivity and reproducibility for DPZ analysis. Under the optimized conditions: separation capillary, 38 cm length (25 μm i.d.); sample injection, 10 s at 8 kV; separation voltage, 12.5 kV; running buffer, 20 mmol L⁻¹ sodium phosphate of pH 6.0; detection potential, 1.15 V; 50 mmol L⁻¹ of phosphate buffer (pH 7.14) containing 5 mmol L⁻¹ of Ru(bpy)₃²⁺ in ECL detection cell, the detection limit of DPZ was 0.05 μmol L⁻¹ (S/N = 3). The linear range extended from 5 to 100 μmol L⁻¹. The linear curve obtained was Y = 181.62 + 9.28X with a correlation coefficient of 0.9970. The relative standard deviations of the ECL intensity and the migration time for six continuous injections of 5 μmol L⁻¹ DPZ were 3.7% and 0.92%, respectively. The CE–ECL method was applied to analyze DPZ in real samples including tablets, rat serum and human urine, and satisfactory results were obtained without interference from samples matrix. The CE–ECL technique was proved to be a potential method for the detection of DPZ in clinic analysis.     

Voltammetric determination of glucose based on reduction of copper(II)–glucose complex at lanthanum hydroxide nanowire modified carbon paste electrodes

A novel voltammetric method for the determination of β-d-glucose (GO) is proposed based on the reduction of Cu(II) ion in Cu(II)(NH₃)₄²⁺–GO complex at lanthanum(III) hydroxide nanowires (LNWs) modified carbon paste electrode (LNWs/CPE). In 0.1 mol L⁻¹ NH₃·H₂O–NH₄Cl (pH 9.8) buffer containing 5.0 × 10⁻⁵ mol L⁻¹ Cu(II) ion, the sensitive reduction peak of Cu(II)(NH₃)₄²⁺–GO complex was observed at −0.17 V (versus, SCE), which was mainly ascribed to both the increase of efficient electrode surface and the selective coordination of La(III) in LNW to GO. The increment of peak current obtained by deducting the reduction peak current of the Cu(II) ion from that of the Cu(II)(NH₃)₄²⁺–GO complex was rectilinear with GO concentration in the range of 8.0 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹, with a detection limit of 3.5 × 10⁻⁷ mol L⁻¹. A 500-fold of sucrose and amylam, 100-fold of ascorbic acid, 120-fold of uric acid as well as gluconic acid did not interfere with 1.0 × 10⁻⁵ mol L⁻¹ GO determination.     

Manipulation of separation selectivity of inorganic anions in electrostatic ion chromatography by the use of mixed cationic–zwitterionic micelles as the column coating solution

This paper describes an electrostatic ion chromatographic system in which the separation selectivity for inorganic anions, especially for sulfate and phosphate, could be manipulated by altering the molar ratio of the zwitterionic and cationic surfactants in the column coating solution used to prepare the stationary phase. The zwitterionic surfactant used for this study was 3-(N,N-dimethyltetradecylammonio)propanesulfonate (Zwittergent-3-14) and the cationic surfactant was tetradecyltrimethylammonium (TTA). Using a reversed-phase C₁₈ column (250×4.6 mm I.D.) coated with 10/10 (mM/mM) of TTA/Zwittergent-3-14 mixed micelles as the stationary phase and either NaHCO₃ or Na₂CO₃ aqueous solution as the eluent, together with suppressed conductivity detection, baseline separation of seven model inorganic anions was obtained. The elution order for those anions was found to be F⁻4²⁻−4²⁻2⁻−3⁻. Under the same conditions but using 1/10 (mM/mM) of TTA/Zwittergent-3-14 mixed micelles as the column coating solution, the elution order for these model ions was F⁻4²⁻4²⁻−2⁻−3⁻. The early elution of phosphate and sulfate is a unique attribute of this system. Detection limits for F⁻, HPO₄²⁻, Cl⁻, SO₄²⁻, NO₂⁻, Br⁻ and NO₃⁻ (S/N=3, sample injection volume 100 μl) were 0.11, 0.12, 0.12, 0.18, 0.49, 0.49, 0.52 μM, respectively.     

Flow injection determination of selenium by successive retention of Se(IV) and tetrahydroborate(III) on an anion-exchange resin and hydride generation electrothermal atomization atomic absorption spectrometry with in-atomizer trapping: Part 1. Method development and investigation of interferences

A sample solution was passed at 20 ml min⁻¹ through a column (150×4 mm²) of Amberlite IRA-410Stron anion-exchange resin for 60 s. After washing, a solution of 0.1% sodium borohydride was passed through the column for 60 s at 5.1 ml min⁻¹. Following a second wash, a solution of 8 mol l⁻¹ hydrochloric acid was passed at 5.1 ml min⁻¹ for 45 s. The hydrogen selenide was stripped from the eluent solution by the addition of an argon flow at 150 ml min⁻¹ and the bulk phases were separated by a glass gas–liquid separator containing glass beads. The gas stream was dried by passing through a Nafion® dryer and fed, via a quartz capillary tube, into the dosing hole of a transversely heated graphite cuvette containing an integrated L’vov platform which had been pretreated with 120 μg of iridium as trapping agent. The furnace was held at a temperature of 250°C during this trapping stage and then stepped to 2000°C for atomization. The calibration was performed with aqueous standards solution of selenium (selenite, SeO₃²⁻) with quantification by peak area. A number of experimental parameters, including reagent flow rates and composition., nature of the gas–liquid separator, nature of the anion-exchange resin, column dimensions, argon flow rate and sample pH, were optimized. The effects of a number of possible interferents, both anionic and cationic were studies for a solution of 500 ng 1⁻¹ of selenium. The most severe depressions were caused by iron (III) and mercury (II) for which concentrations of 20 and 10 mg  1⁻¹ caused a 5% depression on the selenium signal. For the other cations (cadmium, cobalt, copper, lead,. magnesium, and nickel) concentrations of 50–70 mg 1⁻¹ could be tolerated. Arsenate interfered at a concentration of 3 mg⁻¹, whereas concentrations of chloride, bromide, iodide, perchlorate, and sulfate of 500–900 mg l⁻¹ could be tolerated. A linear response was obtained between the detection limit of 4 ng 1⁻¹, with a characteristic mass of 130 pg. The RSDs for solutions containing 100 and 200 ng 1⁻¹ selenium were 2.3% and 1.5%, respectively.     

PVC membrane based potentiometric sensors for uranium determination

Two novel uranyl PVC matrix membrane sensors responsive to uranyl ion are described. The first sensor incorporates tris(2-ethylhexyl)phosphate (TEHP) as both electroactive material and plasticizer and sodium tetraphenylborate (NaTPB) as an ion discriminator. The sensor displays a rapid and linear response for UO₂²⁺ ions over the concentration range 1×10⁻¹–2×10⁻⁵ mol l⁻¹ UO₂²⁺ with a cationic slope of 25.0±0.2 mV decade⁻¹. The working pH range is 2.8–3.6 and the life span is 4 weeks. The second sensor contains O-(1,2-dihydro-2-oxo-1-pyridyl)-N,N,N′,N′-bis(tetra-methylene)uronium hexafluorophosphate (TPTU) as a sensing material, sodium tetraphenylborate as an ion discriminator and dioctyl phenylphosphonate (DOPP) as a plasticizer. Linear and stable response for 1×10⁻¹–5×10⁻⁵ mol l⁻¹ UO₂²⁺ with near-Nernstian slope of 27.5±0.2 mV decade⁻¹ are obtained. The working pH range is 2.5–3.5 and the life span of the sensor is 6 weeks. Interference from many inorganic cations is negligible for both sensors. However, interference caused by some ions (e.g. Th⁴⁺, Cu²⁺, Fe³⁺) is eliminated by a prior ion exchange or solvent extraction step. Direct potentiometric determination of as little as 5 μg ml⁻¹ uranium in aqueous solutions shows an average recovery of 97.2±1.3%. Application for the determination of uranium at levels of 0.01–1 wt.% in naturally occurring and certified ores gives results with good correlation with data obtained by X-ray fluorescence.     

Enhancement of the chemiluminescence of penicillamine and ephedrine after derivatization with aldehydes using tris(bipyridyl)ruthenium(II) peroxydisulfate system and its analytical application

A novel sequential injection (SI) method was developed for the determination of penicillamine (PA) and ephedrine (EP) based on the reaction of these drugs with tris(bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) and peroxydisulfate (S₂O₈²⁻) in the presence of light. Derivatization of PA and EP with aldehydes has resulted in a significant enhancement of the chemiluminescence emission signal by at least 25 times for PA and 12 times for EP, leading to better sensitivities and lower detection limits for both drugs. The instrumental setup utilized a syringe pump and a multiposition valve to aspirate the reagents, (Ru(bpy)₃²⁺ and S₂O₈²⁻), and a peristaltic pump to propel the sample. The experimental conditions affecting the derivatization reaction and the chemiluminescence reaction were systematically optimized using the univariate approach. Under the optimum conditions linear calibration curves between 0.2–24 μg mL⁻¹ for PA and 0.2–20 μg mL⁻¹ for EP were obtained. The detection limits were 0.1 μg mL⁻¹ for PA and 0.03 μg mL⁻¹ for EP. The procedure was applied to the analysis of PA and EP in pharmaceutical products and was found to be free from interferences from concomitants usually present in these preparations.     

Capillary electrophoresis for measuring major and trace anions in thermal water and condensed-steam samples from hydrothermal springs and fumaroles

A new application of capillary electrophoresis for measuring major and trace anions in thermal water and condensed-steam samples is presented. Ten fluid samples were collected from hydrothermal springs and fumaroles located in a volcanic zone of Deception Island, Antarctica. Anion separation was achieved in less than 6 min using indirect UV detection at 254 nm with a negative power supply (−15 kV). The electrolyte consisted of 4.7 mM sodium chromate, 4.0 mM electroosmotic flow modifier (OFM) hydroxide, 10 mM 2-(N-cyclohexylamino)ethanesulfonic acid and 0.1 mM calcium gluconate (pH 9.1). Major anions (Cl⁻, SO₄², PO₄H²⁻, and CO₃H⁻) were measured using hydrostatic injection (10 cm for 30 s) at 25°C. Trace amounts of anions (F⁻, Br⁻, and NO₃⁻) were better determined by electromigration injection (4 kV, 10 s) at 15°C. Good reproducibility of the migration times (<0.72% RSD), a satisfactory linear response and accuracy as well as acceptable detection limits were successfully obtained.     

Sequential injection sample introduction microfluidic-chip based capillary electrophoresis system

A sequential injection micro-sample introduction system was coupled to a microfluidic-chip based capillary electrophoresis system through a split–flow sampling interface integrated on the micro-chip. The microfluidic system measured 20×70×3 mm in dimension, and was produced using a non-lithographic approach with components readily available in the analytical laboratory. In the H-configuration channel design the horizontal separation channel was a 75 μm I.D.×60 mm quartz capillary, with two vertical side arms produced from plastic tubing. The conduits were embedded in silicon elastomer with a planar glass base. Sequential introduction of a series of samples with about 2.5% carryover was achieved at 48 h⁻¹ throughput with samples containing a mixture of fluorescein isothiocyanate (FITC)-labeled amino acids using SI sample volumes of 3.3 μl and carrier flow-rate of 2.0 ml min⁻¹. Baseline separation was achieved for FITC-labeled arginine, phenylalanine, glycine and FITC (laser induced fluorescence detection) in sodium tetraborate buffer (pH 9.2) within 8–80 s, at separation lengths of 25–35 mm and electrical field strengths of 250–1500 V cm⁻¹, with plate heights in the 0.7–3 μm range.     

Ligand deprotonation significance in the formation of the molybdate ion-malic acid complexes

Using the temperature jump technique, the study of the kinetics of the complexing of oxomolybdate anion with malic acid has been carried out in aqueous solutions of pH 7.15–8.5 at ionic strength 0.1 M (KNO₃) and 25°'C. A reaction scheme for the formation of 1 : 1 complexes is proposed which accounts for the observed relaxation rates.

The significance of the ligand deprotonation on the complexation reaction of MoO₄²⁻ by a single protonated ligand, i.e. MoO₄²⁻+LH^nk→MoO₃(OH)Lⁿ⁻², (where n = 1 -, 2 -, etc), is analysed on the basis of a simple model. A linear correlation between the log k and the pK of the monoprotonated ligand (LH) is found for this reaction when the global process is controlled by the proton transfer from the ligand to an oxogroup, i.e. log k = a - 0.5xpK. It is found that this correlation is satisfied by MoO₄²⁻ and WO₄²⁻. The experimental slopes for these oxyanions are −0.503 and −0.543 respectively, in agreement with the predictions.     

On the conformational stability and dimerization of phosphotransferase enzyme I from Escherichia coli

The activity of enzyme I (EI), the first protein in the bacterial PEP:sugar phosphotransferase system, is regulated by a monomer–dimer equilibrium where a Mg²⁺-dependent autophosphorylation by PEP requires the homodimer. Using inactive EI(H189A), in which alanine is substituted for the active-site His189, substrate binding effects can be separated from those of phosphorylation. Whereas 1 mM PEP (with 2 mM Mg²⁺) strongly promotes dimerization of EI(H189A) at pH 7.5 and 20 °C, 5 mM pyruvate (with 2 mM Mg²⁺) has the opposite effect. A correlation between the coupling of N- and C-terminal domain unfolding, measured by differential scanning calorimetry, and the dimerization constant for EI, determined by sedimentation equilibrium, is observed. That is, when the coupling between N- and C-terminal domain unfolding produced by 0.2 or 1.0 mM PEP and 2 mM Mg²⁺ is inhibited by 5 mM pyruvate, the dimerization constant for EI(H189A) decreases from >10⁸ to <5 × 10⁵ or 3 × 10⁷ M⁻¹, respectively. With 2 mM Mg²⁺ at 15–25 °C and pH 7.5, PEP has been found to bind to one site/monomer of EI(H189A) with K_A′10⁶ M⁻¹ (ΔG′=−33.7±0.2 kJ mol⁻¹ and ΔH=+16.3 kJ mol⁻¹ at 20 °C with ΔC_p=−1.4 kJ K⁻¹ mol⁻¹). The binding of PEP to EI(H189A) is synergistic with that of Mg²⁺. Thus, physiological concentrations of PEP and Mg²⁺ increase, whereas pyruvate and Mg²⁺ decrease the amount of dimeric, active, dephospho-enzyme I.     

Sequential injection analysis (SIA)-chemiluminescence determination of indomethacin using tris[(2,2'-bipyridyl)]ruthenium(III) as reagent and its application to semisolid pharmaceutical dosage forms

Automated sequential injection (SIA) method for chemiluminescence (CL) determination of nonsteroidal anti-inflammatory drug indomethacin (I) was devised. The CL radiation was emitted in the reaction of I (dissolved in aqueous 50% v/v ethanol) with intermediate reagent tris(2,2′-bipyridyl)ruthenium(III) (Ru(bipy)₃³⁺) in the presence of acetate. The Ru(bipy)₃³⁺ was generated on-line in the SIA system by the oxidation of 0.5 mM tris(2,2′-bipyridyl)ruthenium(II) (Ru(bipy)₃²⁺) with Ce(IV) ammonium sulphate in diluted sulphuric acid. The optimum sequence, concentrations, and aspirated volumes of reactant zones were: 15 mM Ce(IV) in 50 mM sulphuric acid 41 μL, 0.5 mM Ru(bipy)₃²⁺ 30 μL, 0.4 M Na acetate 16 μL and I sample 15 μL; the flow rates were 60 μL s⁻¹ for the aspiration into the holding coil and 100 μL s⁻¹ for detection. Calibration curve relating the intensity of CL (peak height of the transient CL signal) to concentration of I was curvilinear (second order polynomial) for 0.1–50 μM I (r = 0.9997; n = 9) with rectilinear section in the range 0.1–10 μM I (r = 0.9995; n = 5). The limit of detection (3σ) was 0.05 μM I. Repeatability of peak heights (R.S.D., n = 10) ranged between 2.4% (0.5 μM I) and 2.0% (7 μM I). Sample throughput was 180 h⁻¹. The method was applied to determination of 1 to 5% of I in semisolid dosage forms (gels and ointments). The results compared well with those of UV spectrophotometric method.     

Peroxidase immobilized on Amberlite IRA-743 resin for on-line spectrophotometric detection of hydrogen peroxide in rainwater

The importance of atmospheric hydrogen peroxide (H₂O₂) in the oxidation of SO₂ and other compounds has been well established. A spectrophotometric method for the determination of hydrogen peroxide in rainwater is proposed. This method is based on selective oxidation of hydrogen peroxide using an on-line tubular reactor containing peroxidase immobilized on Amberlite IRA-743 resin. The hydrogen peroxide in the presence of phenol, 4-aminoantipyrine and peroxidase, produces a red compound (λ = 505 nm). Beer's law is obeyed in a concentration range of 1–100 μmol l⁻¹ hydrogen peroxide with an excellent correlation coefficient (r = 0.9991), at pH 7.0, with a relative standard deviation (R.S.D.) <2%. The detection limit of the method is 0.7 μmol l⁻¹ (4.8 ng of H₂O₂ in a 200 μl sample). Measurements of hydrogen peroxide in rain samples were carried out over the period from November 2003 to January 2005, in the central area of the Juiz de Fora city, Brazil. The concentration of H₂O₂ varied from values lower than the detection limit to 92.5 μmol l⁻¹. The effects of the presence of nonseasalt (NSS) SO₄²⁻, NO₃⁻ and H⁺ in the concentration of hydrogen peroxide in the rainwater had been evaluated. The average concentrations of H₂O₂, NO₃⁻, NSS SO₄²⁻ and SO₄²⁻ are 23.4, 18.9, 7.9 and 10.3 μmol l⁻¹, respectively. The pH values for 82% of the collected samples are greater than 5.0. The spectrophotometeric method developed in this work that uses enzyme immobilized on the resin ion-exchange compared with the amperometric method did not present any significant difference in the results.     

A new immune resonance scattering spectral assay for trace fibrinogen with gold nanoparticle label

An on-line stacking method based on moving reaction boundary (MRB) was developed for the sensitive determination of barbital and phenobarbital in human urine via capillary electrophoresis (CE). The optimized conditions for the method are: 60 mmol L⁻¹ pH 11.0 Gly–NaOH as the background electrolyte, 10 mmol L⁻¹ pH 5.5 Gly–HCl as sample buffer, secobarbital as the internal standard (IS), 12.5 kV, 1.4 psi 10 s sample injection, 75 μm ID 60.2 cm total length (50 cm effective length) capillary and 214 nm detect wavelength. Under the optimized conditions, the method can well stack and separate barbital and phenobarbital in urine samples and result in 20.5-fold and 22.6-fold improvement in concentration sensitivity for barbital and phenobarbital, respectively. Furthermore, the method holds: (1) good linear calibration functions for the two target compounds (correlation coefficients r > 0.999), (2) low limits of detection (0.27 μg mL⁻¹ for barbital and 0.26 μg mL⁻¹ for phenobarbital), (3) low limits of quantification (0.92 μg mL⁻¹ for barbital and 0.87 μg mL⁻¹ for phenobarbital), (4) good precision (R.S.D. of intra-day and inter-day less than 5.38% for barbital and 1.67% for phenobarbital, respectively) and (5) high recoveries at three concentration levels (90.27–106.36% for barbital and 93.05–113.60% for phenobarbital in urine). The method is simple, sensitive and efficient, and can fit to the need of clinical and forensic toxicology.     

The direct synthesis of dimethyl ether from syngas over hybrid catalysts with sulfate-modified γ-alumina as methanol dehydration components

A series of γ-Al₂O₃ samples modified with various contents of sulfate (0–15 wt.%) and calcined at different temperatures (350–750 °C) were prepared by an impregnation method and physically admixed with CuO–ZnO–Al₂O₃ methanol synthesis catalyst to form hybrid catalysts. The direct synthesis of dimethyl ether (DME) from syngas was carried out over the prepared hybrid catalysts under pressurized fixed-bed continuous flow conditions. The results revealed that the catalytic activity of SO₄²⁻/γ-Al₂O₃ for methanol dehydration increased significantly when the content of sulfate increased to 10 wt.%, resulting in the increase in both DME selectivity and CO conversion. However, when the content of sulfate of SO₄²⁻/γ-Al₂O₃ was further increased to 15 wt.%, the activity for methanol dehydration was increased, and the selectivity for DME decreased slightly as reflected in the increased formation of byproducts like hydrocarbons and CO₂. On the other hand, when the calcination temperature of SO₄²⁻/γ-Al₂O₃ increased from 350 °C to 550 °C, both the CO conversion and the DME selectivity increased gradually, accompanied with the decreased formation of CO₂. Nevertheless, a further increase in calcination temperature to 750 °C remarkably decreased the catalytic activity of SO₄²⁻/γ-Al₂O₃ for methanol dehydration, resulting in the significant decline in both DME selectivity and CO conversion. The hybrid catalyst containing the SO₄²⁻/γ-Al₂O₃ with 10 wt.% sulfate and calcined at 550 °C exhibited the highest selectivity and yield for the synthesis of DME.     

Electrochemiluminescence sensor using tris(2,2′-bipyridyl)ruthenium(II) immobilized in Eastman-AQ55D–silica composite thin-films

An electrochemiluminescence (ECL) sensor with good long-term stability and fast response time has been developed. The sensor was based on the immobilization of tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) into the Eastman-AQ55D–silica composite thin films on a glassy carbon electrode. The ECL and electrochemistry of Ru(bpy)₃²⁺ immobilized in the composite thin films have been investigated, and the modified electrode was used for the ECL detection of oxalate, tripropylamine (TPA) and chlorpromazine (CPZ) in a flow injection analysis system and showed high sensitivity. Because of the strong electrostatic interaction and low hydrophobicity of Eastman-AQ55D, the sensor showed no loss of response over 2 months of dry storage. In use, the electrode showed only a 5% decrease in response over 100 potential cycles. The detection limit was 1 μmol l⁻¹ for oxalate and 0.1 μmol l⁻¹ for both TPA and CPZ (S/N=3), respectively. The linear range extended from 50 μmol l⁻¹ to 5 mmol l⁻¹ for oxalate, from 20 μmol l⁻¹ to 1 mmol l⁻¹ for TPA, and from 1 μmol l⁻¹ to 200 μmol l⁻¹ for CPZ.     

Ion-exchange properties of hypercrosslinked polystyrene impregnated with methyl orange

A novel bipolar stationary phase (HCPS–MO) was prepared by impregnation of hypercrosslinked polystyrene (HCPS) with methyl orange (MO; 4-dimethylamino-4′-sulfoazobenzene) and its ion-exchange properties were studied. Simultaneous separation of cations and anions on HCPS–MO is possible, although it behaves preferentially as a cation-exchanger. Unusual selectivity of HCPS-MO for alkali and alkaline-earth metal cations: Na⁺+K⁺+4⁺+ and Mg²⁺2+2+2+ was observed. The effect of temperature on retention of alkali and alkaline-earth metal cations was studied. Separation of Na⁺, K⁺, Rb⁺, NH₄⁺, Cs⁺, Mg²⁺ and Ca²⁺ on HCPS–MO with diluted cerium(III) nitrate solution as an eluent in single run is presented.     

Phosphate-selective electrodes containing immobilised ionophores

Phosphate selective electrodes have been produced based upon rubbery membranes containing heterocylic macrocycles as sensors covalently bound to a cross-linked polystyrene-block–polybutadiene-block–polystyrene (SBS) polymer. The membranes were robust and the best HPO₄²⁻-selective membrane fabricated was composed of 7.1% (m/m) dicumyl peroxide, 28.3% (m/m) 2-nitrophenyloctylether, 9.8% (m/m) 3-(10-undecenyl)-1,5,8-triazacyclodecane-2,4-dione, 31.0% (m/m) SBS and 23.8% (m/m) PoleStar™ 200R (clay-based filler). The characteristics of this electrode were a linear Nernstian range of 3.9×10⁻³ to 1×10⁻⁶ mol dm⁻³ HPO₄²⁻ with a limit of detection of 1.0×10⁻⁶ mol dm⁻³ HPO₄²⁻, a slope of −29.7±0.9 mV per activity decade and a pH range from 6 to 8. Selectivity coefficients for phosphate against various interfering anions (chloride, sulfate and nitrate) were determined. Response times were 2 min or under, stability of response and electrode lifetime in continuous use were also very satisfactory. The response behavior of HPO₄²⁻-ISEs based upon mobile and bound ionophores was comparable and suggests that mobility of the ionophore is not necessary to obtain a working ISE and that covalent binding of ionophores can be used to produce ISEs of increased stability and robustness.     

Electrochemiluminescent behavior of allopurinol in the presence of Ru(bpy)(3)(2+)

The electrochemiluminescent (ECL) response of allopurinol was studied in aqueous media over a wide pH range (pH 2–13) using flow injection (FI) analysis. It was revealed that allopurinol itself had no ECL activity, but could greatly enhance the ECL of Ru(bpy)₃²⁺ in alkaline media giving rise to a sensitive FI-ECL response. The effects of experimental conditions including the mode of applied voltage signal, the potential of working electrode, pH value, the flow rate of carrier solution, and the concentration of Ru(bpy)₃²⁺ and allopurinol on the ECL intensity were investigated in detail. The most sensitive FI-ECL response of allopurinol was found at pH 12.0, where the FIA-ECL intensity showed a linear relationship with concentration of allopurinol in the range 1 × 10⁻⁸ mol L⁻¹ to 5 × 10⁻⁷ mol L⁻¹, and the detection limit was 5 × 10⁻⁹ mol L⁻¹.     

A Gaussian-2 ab initio study of [C2H5S] ions: III. H2 and CH4 eliminations from CH3CHSH and CH3SCH2

Gaussian-2 ab initio calculations were performed to examine the six modes of unimolecular dissociation of cis-CH₃CHSH⁺ (1⁺), trans-CH₃CHSH⁺ (2⁺), and CH₃SCH₂⁺ (3⁺): 1⁺→CH₃⁺+trans-HCSH (1); 1⁺→CH₃+trans-HCSH⁺ (2); 1⁺→CH₄+HCS⁺ (3); 1⁺→H₂+c-CH₂CHS⁺ (4); 2⁺→H₂+CH₃CS⁺ (5); and 3⁺→H₂+c-CH₂CHS⁺ (6). Reactions (1) and (2) have endothermicities of 584 and 496 kJ mol⁻¹, respectively. Loss of CH₄ from 1⁺ (reaction (3)) proceeds through proton transfer from the S atom to the methyl group, followed by cleavage of the C–C bond. The reaction pathway has an energy barrier of 292 kJ mol⁻¹ and a transition state with a wide spectrum of nonclassical structures. Reaction (4) has a critical energy of 296 kJ mol⁻¹ and it also proceeds through the same proton transfer step as reaction (3), followed by elimination of H_2. Formation of CH₃CS⁺ from 2⁺ (reaction (5)) by loss of H₂ proceeds through protonation of the methine (CH) group, followed by dissociation of the H₂ moiety. Its energy barrier is 276 kJ mol⁻¹. On both the MP2/6-31G* and QCISD/6-31G* potential-energy surfaces, the H₂ 1,1-elimination from 3⁺ (reaction (6)) proceeds via a nonclassical intermediate resembling c-CH₃SCH₂⁺ and has a critical energy of 269 kJ mol⁻¹.     

Role of axial ligand on the electronic structures of active intermediates in cytochrome P-450, peroxidase and catalase

DFT method (B3LYP) with 6-31G^* basis set was utilized in the computation of a fully optimized structure, net atomic charges and spin densities of the intermediate of cytochrome P-450-oxoiron(IV) porphyrin cation radical, compound I – in the presence of axial ligand such as thiolate (SMe⁻) imidazole (IM), phenoxide (OPh⁻), methoxide (OMe⁻) and chloride (Cl⁻). The results show doublet states in compound I are about 2–4 kcal/mol more stable than quartet states for all aforementioned ligands, and the doublet state is the ground state in all cases. However, electron donor ability of the ligands are in the order of SMe⁻ > IM > OMe⁻ > OPh⁻ > Cl⁻. Also the active oxidant intermediate of cytochrome P-450 between different mesomeric structures select sulfur oxygen radical type structure and can be viewed as (RS^↓)Fe^↑(IV)(O^↑)(Por). In horseraddish peroxidase (HRP) and peroxidase with histidine axial ligand π cation radical character of porphyrin ring is preferred (Im)Fe^↑(IV)(O^↑)(Por^↓). For the ligands such as OMe⁻, OPh⁻ and Cl⁻ oxidation mainly took place on the iron and the active intermediate can be viewed as (L)Fe^↑(V)(O)(Por) with one unpaired electron localized on the iron.