Exploration of high‐resolution ultrasonic spectroscopy as an analytical tool to study demixing and remixing in poly(N‐isopropyl acrylamide)/water solutions

The ultrasonic properties of poly(N‐isopropyl acrylamide) (PNIPAM)/water solutions, determined with high‐resolution ultrasonic spectroscopy (HR‐US), change during demixing and remixing. All HR‐US measurements are discussed with respect to modulated temperature differential scanning calorimetry results. The lower critical solution temperature type of phase behavior, in combination with the glass‐transition/composition curve of PNIPAM/water, determines the evolution of the ultrasonic signals. Three different temperature regions can be distinguished: a homogeneous region and a heterogeneous region, the latter subdivided into zones without and with interference of partial vitrification of the PNIPAM‐rich phase. During phase separation, the ultrasonic velocity decreases because of a change in the hydration structure around the polymer chains, whereas the ultrasonic attenuation increases as aggregation sets in. Isothermal measurements clearly show time dependence for both the velocity and the attenuation. The observed timescales are different and can be related to a changing polymer/water interphase and aggregate formation, respectively. Partial vitrification of the PNIPAM‐rich phase slows the demixing kinetics and especially the remixing kinetics. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1283–1295, 2005     

Interfacial interaction in EVA‐carbon nanotube and EVA‐clay nanocomposites

Proper filler‐matrix compatibility is a key factor in view of obtaining nanocomposites with well‐dispersed nanofillers displaying enhanced properties. In this respect, polymer‐filler interaction can be improved by a proper combination of matrix and nanofiller polarities. This is explored for matrices ranging from nonpolar high density poly(ethylene) to ethylene‐vinyl acetate (EVA) copolymers with varying vinyl acetate contents, in combination with several types of organoclay or carbon nanotubes. A novel in situ characterization methodology using modulated temperature differential scanning calorimetry is presented to evaluate the matrix‐filler interaction. During quasi‐isothermal crystallization of the matrix, an “excess” contribution is observed in the recorded heat capacity signal because of reversible melting and crystallization. Its magnitude considerably decreases upon addition of nanofiller in case of strong interfacial interaction, whereas the influence is moderate in case of a less interacting matrix‐filler combination. It is suggested that the “excess heat capacity” can be used to quantify the segmental mobility of polymer chains in the vicinity of the nanofiller. Hence it provides valuable information on the strength of interaction, governed by the physical and chemical nature of matrix and filler. Heating experiments subsequent to quasi‐isothermal crystallization point at a certain degree of molecular ordering, responsible for crystal nucleation in EVA copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1291–1302, 2007     

Reversible and irreversible heat capacity of poly[carbonyl(ethylene‐co‐propylene)] by temperature‐modulated calorimetry

The heat capacity of poly[carbonyl(ethylene‐co‐propylene)] with 95 mol % C₂H₄? CO? (Carilon EP®) was measured with standard differential scanning calorimetry (DSC) and temperature‐modulated DSC (TMDSC). The integral functions of enthalpy, entropy, and free enthalpy were derived. With quasi‐isothermal TMDSC, the apparent reversing heat capacity was determined from 220 to 570 K, including the glass‐ and melting‐transition regions. The vibrational heat capacity of the solid and the heat capacity of the liquid served as baselines for the quantitative analysis. A small amount of apparent reversing latent heat was found in the melting range, just as for other polymers similarly analyzed. With an analysis of the heat‐flow rates in the time domain, information was collected about latent heat contributions due to annealing, melting, and crystallization. The latent heat decreased with time to an even smaller but truly reversible latent heat contribution. The main melting was fully irreversible. All contributions are discussed in the framework of a suggested scheme of six physical contributions to the apparent heat capacity. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1565–1577, 2001     

Reversible melting and crystallization of high‐molar‐mass poly(oxyethylene)

The heat capacity of poly(oxyethylene) (POE) with a molar mass of 900,000 Da has been analyzed with differential scanning calorimetry and quasi‐isothermal, temperature‐modulated differential scanning calorimetry. The crystal structure, lattice parameters, and coherently scattering domain sizes have been measured with wide‐angle X‐ray diffraction as a function of temperature. The high‐molar‐mass POE crystals are in a folded‐chain macroconformation and show some locally reversible melting starting already at about 250 K. At 335 K, the thermodynamic heat capacity reaches the level of the melt. The reversible crystallinity depends on the modulation amplitude and has been varied in the melting range from ±0.2 to ±3.0 K. Before melting, there is neither a change in the crystal structure nor a change in the domain size, but the expansivity of the crystals increases at about 320 K. These observations support the interpretation that the monoclinic POE crystals possess a glass transition temperature with a midpoint at about 324 K, whereas the maximum melting temperature is 341 K. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 475–489, 2007     

Reversible and irreversible heat capacity of poly(trimethylene terephthalate) analyzed by temperature‐modulated differential scanning calorimetry

The heat capacity of poly(trimethylene terephthalate) (PTT) has been analyzed using temperature‐modulated differential scanning calorimetry (TMDSC) and compared with results obtained earlier from adiabatic calorimetry and standard differential scanning calorimetry (DSC). Using quasi‐isothermal TMDSC, the apparent reversing and nonreversing heat capacities were determined from 220 to 540 K, including glass and melting transitions. Truly reversible and time‐dependent irreversible heat effects were separated. The extrapolated vibrational heat capacity of the solid and the total heat capacity of the liquid served as baselines for the analysis. As one approaches the melting region from lower temperature, semicrystalline PTT shows a reversing heat capacity, which is larger than that of the liquid, an observation that is common also for other polymers. This higher heat capacity is interpreted as a reversible surface or bulk melting and crystallization, which does not need to undergo molecular nucleation. Additional time‐dependent, reversing contributions, dominating at temperatures even closer to the melting peak, are linked to reorganization and recrystallization (annealing), while the major melting is fully irreversible (nonreversing contribution). © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 622–631, 2000     

Annealing behavior of gel‐spun polyethylene fibers at temperatures lower than needed for significant shrinkage

The annealing at 373 K of ultrastrong, gel‐spun polyethylene (PE) has been studied. At this temperature, the fibers show no significant shrinkage. Still, a significant decrease in the mechanical properties is observed. The fibers have been analyzed with differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), atomic force microscopy (AFM), and small‐angle X‐ray scattering (SAXS). During the annealing, the glass transition of the intermediate phase is exceeded, as shown by DSC. When split for structure analysis by AFM, the annealed fibers undergo plastic deformation around the base fibrils instead of brittle fracture. The quasi‐isothermal TMDSC experiments are compared to the minor structural changes seen with SAXS and AFM. The loss of performance of the PE fibers at 373 K is suggested to be caused by the oriented intermediate phase, and not by major changes in the structure or morphology. The overall metastable, semicrystalline structure is shown by TMDSC to posses local regions that can melt reversibly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 403–417, 2003     

Recent developments in thermal analysis of polymers: Calorimetry in the limit of slow and fast heating rates

This review focuses on new insights into the crystal melting transition and the amorphous glass transition of polymers that have been gained through recent advances in thermoanalytical methods. The specific heat capacity can now be studied under two extreme limits, that is, under quasi‐isothermal conditions (limit of zero heating rate) and, at the other end of the scale, under rapid heating conditions (heating rates on the order of thousands of degrees per second), made possible through nanocalorimetry. The reversible melting, and multiple reversible melting, of semicrystalline polymers is explored using quasi‐isothermal temperature modulated differential scanning calorimetry, TMDSC. The excess reversing heat capacity, above the baseline, measured under nearly isothermal conditions is attributed to locally reversible surface melting and crystallization processes that do not require molecular nucleation. Observations of double reversible melting endotherms in isotactic polystyrene suggest existence of two distinct populations of crystals, each showing locally reversible surface melting. The second subject of the review, nanocalorimetry, is utilized to study samples of small mass under conditions of very fast heating and cooling. The glass transition properties of thin amorphous polymer films are observed under adiabatic conditions. The glass transition temperature appears to be independent of film thickness, and is observed even in ultra‐thin films. Recrystallization and reorganization during rapid heating are studied by nanocalorimetry of semicrystalline polymers. The uppermost endotherm seen under normal DSC scanning of poly(ethylene terephthalate) is caused by reorganization, and vanishes under the rapid heating conditions (3000K/s) provided by nanocalorimetry. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 629–636, 2005     

Temperature Dependence of Sol‐Gel Conversion Kinetics in Gelatin‐Water System

The conversion kinetics of an aqueous gelatin solution to gel was studied by temperature modulated and regular DSC under isothermal and continuous cooling conditions. Isothermal runs revealed a decrease in the quasi‐static heat capacity primarily associated with syneresis (phase separation) of the gel. Above 19 °C the isothermal process demonstrated negative effective activation energy that turned positive below 14 °C. Continuous cooling runs detected a reversing heat flow apparently related to the continuing formation and melting of new gel structures. Isoconversional kinetic analysis of continuous cooling measurements yielded negative activation energy for the whole range of conversions and temperatures suggesting that nucleation remained a rate controlling step throughout the whole gelation process.

     

Thermal memory of poly(3‐hydroxybutyrate) using temperature‐modulated differential scanning calorimetry

The influence of thermal history on morphology, melting, and crystallization behavior of bacterial poly(3‐hydroxybutyrate) (PHB) has been investigated using temperature‐modulated DSC (TMDSC), wide‐angle X‐ray diffraction (WAXRD) and polarized optical microscopy (POM). Various thermal histories were imparted by crystallization with continuous and different modulated cooling programs that involved isoscan and cool–heat segments. The subsequent melting behavior revealed that PHB experienced secondary crystallization during heating and the extent of secondary crystallization varied with the cooling treatment. PHB crystallized under slow, continuous, and moderate cooling rates were found to exhibit double melting behavior due to melting of TMDSC scan‐induced secondary crystals. PHB underwent considerable secondary crystallization/annealing that took place under modulated cooling conditions. The overall melting behavior was interpreted in terms of recrystallization and/or annealing of crystals. Interestingly, the PHB analyzed by temperature modulation programs showed a broad exotherm before the melting peak in the nonreversing heat capacity curve and a multiple melting reversing curve, verifying that the melting–recrystallization and remelting process was operative. WAXRD and POM studies supported the correlations from DSC and TMDSC results. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 70–78, 2006     

Study on nonlinear phase‐separation for PMMA/α‐MSAN blends by dynamic rheological and small angle light scattering measurements

The phase‐separation behavior of poly(methyl methacrylate)/poly(α‐methyl styrene‐co‐acrylonitrile) (PMMA/α‐MSAN) blends upon heating was studied through dynamic rheological measurements and time‐resolved small angle light scattering, as a function of temperatures and heating rates. The spinodal temperatures could be obtained by an examination of the anomalous critical viscoelastic properties in the vicinity of phase‐separation induced by the enhanced concentration fluctuation on the basis of the mean field theory. It is found that the dependence of the critical temperatures determined by dynamic rheological measurements and small angle light scattering on heating rates both deviates obviously from the linearity, even at the very low heating rates. Furthermore, the cloud‐point curves decrease gradually with the decrease of heating rates and present the trend of approaching T_gs of the blends. The nonlinear dependence is in consistence with that extracted from the isothermal phase‐separation behavior as reported in our previous paper. It is suggested that the equilibrium phase‐separation temperature could be hardly established by the linear extrapolating to zero in the plotting of cloud points versus heating rates. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1547–1555, 2006     

Miscibility of polysulfone blends with poly(1‐vinylpyrrolidone‐co‐styrene) copolymers and their interaction energies

The miscibility of polysulfone (PSf) with various hydrophilic copolymers was explored. Among these blends, PSf gave homogeneous mixtures with poly(1‐vinylpyrrolidone‐co‐styrene) [P(VP–S)] copolymers when these copolymers contained 68–88 wt % 1‐vinylpyrrolidone (VP). Miscible PSf blends with P(VP–S) copolymers underwent phase separation on heating caused by lower critical solution temperature (LCST)‐type phase behavior. The phase behavior depended on the copolymer composition. Changes in the VP content of P(VP–S) copolymers from 65 to 68 wt % shifted the phase behavior from immiscibility to miscibility and the LCST behavior. The phase‐separation temperatures of the miscible blends first increased gradually with the VP content, then went through a broad maximum centered at about 80 wt % VP, and finally decreased just before the limiting content of VP for miscibility with PSf. The interaction energies of binary pairs involved in PSf/P(VP–S) blends were evaluated from the phase‐separation temperatures of PSf/P(VP–S) blends with lattice‐fluid theory combined with a binary interaction model. The decrease in the contact angle between water and the membrane surface with increasing VP content in P(VP–S) copolymers indicated that the hydrophobic properties of PSf could be improved via blending with hydrophilic P(VP–S) copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1401–1411, 2003     

Reversibility of the low‐temperature transitions of polytetrafluoroethylene as revealed by temperature‐modulated differential scanning calorimetry

Temperature‐modulated differential scanning calorimetry reveals distinct differences in the kinetics of the low‐temperature phase transitions of polytetrafluoroethylene. The triclinic to trigonal transition at 292 K is partially reversible as long it is not complete. As soon as the total sample is converted, supercooling is required to nucleate the reversal of the helical untwisting involved in the transition. The trigonal phase can be annealed in the early stages after transformation with a relaxtion time of about 5 minutes. The dependence of the reversing heat capacity on the modulation amplitude, after a metastable equilibrium has been reached, is explained by a non‐linear, time‐independent increase of the heat‐flow rate, perhaps caused by an increased true heat capacity. The order‐disorder‐transition at 303 K from the trigonal to a hexagonal condis phase is completely reversible and time‐independent. It extends to temperatures as low as the transition at 292 K or even lower. Qualitatively, the thermal history and crystallization conditions of polytetrafluoroethylene do not affect the transition kinetics, that is, melt‐crystallized film and as‐polymerized powders show similar transition behaviors, despite largely different crystallinities. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 750–756, 2001     

Segmental‐ and normal‐mode dielectric relaxation of poly(propylene glycol) under pressure

Dielectric measurements were obtained on poly(propylene glycol) (molecular weight: 4000 Da) at pressures in excess of 1.2 GPa. The segmental (α process) and normal‐mode (α′ process) relaxations exhibited different pressure sensitivities of their relaxation strengths, as well as their relaxation times. Such results are contrary to previous reports, and (at least for the dielectric strength) can be ascribed to the capacity for intermolecular hydrogen‐bond formation in this material. With equation‐of‐state measurements, the relative contributions of volume and thermal energy to the α‐relaxation times were quantified. Similar to other H‐bonded liquids, temperature is the more dominant control variable, although the effect of volume is not negligible. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3047–3052, 2003     

Evidence for coupling and decoupling of parts of macromolecules by temperature‐modulated calorimetry

Equilibrium crystals of linear macromolecules have an extended‐chain macroconformation. They can melt at the equilibrium melting temperature, whereas crystallization needs considerable supercooling, even in the presence of crystal nuclei, making the overall phase transition irreversible. The same molecules with a metastable, chain‐folded macroconformation may have a large amount of specific reversibility, that is, a fraction of the same polymer molecule that melts irreversibly may also show decoupled, reversible melting. The overall metastable, nanophase structure of such semicrystalline polymers may thus support local equilibria. The tool for the quantitative analysis is quasi‐isothermal temperature‐modulated calorimetry that can separate reversible from irreversible processes. A major review of the study of crystals of more than 20 polymers has been published. On the basis of this extensive body of information, a first discussion of decoupling of parts of macromolecules is attempted and linked to previous studies of phase equilibria. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1275–1288, 2004     

Phase separation in dilute polymer solutions at high‐rate extension

In this article the demixing instability and phase segregation in unentangled polymer solutions of semiflexible chains at high‐rate uniaxial extension above the coil to stretched coil transition was studied. Orientation of the stretched chains was described in terms of an effective potential field. Based on the free energy analysis it was shown that the flow‐induced orientation of polymer segments could drastically reduce the energy of their steric repulsion. As a result attraction between the chains gain more importance, and this effect lead to the demixing process and eventual segregation of polymer from the solvent if the strain rate exceeds some critical value. A mean‐field theory was developed to study this flow‐induced phase separation effect. The phase diagrams of the system showing the spinodal and binodal transitions at different extension rates were calculated and discussed. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1066–1073     

Enthalpy relaxation of an epoxy–anhydride resin by temperature‐modulated differential scanning calorimetry

The enthalpy relaxation of an epoxy–anhydride resin was studied by physical aging and frequency‐dependence experiments with alternating differential scanning calorimetry (ADSC), which is a temperature‐modulated differential scanning calorimetry technique. The samples were aged at 80 °C, about 26 K below the glass‐transition temperature, for periods up to 3800 h and then scanned under the following modulation conditions: underlying heating rate of 1 K min⁻¹, amplitude of 0.5 K, and period of 1 min. The enthalpy loss was calculated by the total heat‐flow signal, and its variation with the log (aging time) gives a relaxation rate (per decade), this value being in good agreement with that calculated by conventional DSC. The enthalpy loss was also analyzed in terms of the nonreversing heat flow, revealing that this property is not suitable for calculating enthalpy loss. The effect of aging on the modulus of the complex heat capacity, |Cp*|, is shown by a sharper variation on the low side of the glass transition and an increase in the inflexional slope of |Cp*|. Likewise, the phase angle also becomes sharper in the low‐temperature side of the relaxation. The area under the corrected out‐phase heat capacity remains fairly constant with aging. The dependence of the dynamic glass transition, measured at the midpoint of the variation of |Cp*|, on ln(frequency) allows one to determine an apparent activation energy, Δh*, which gives information about the temperature dependence of the relaxation times in equilibrium over a range close to the glass transition. The values of Δh*, determined from ADSC experiments in a range of frequencies between 4.2 and 33 mHz and at an amplitude of 0.5 K, and an underlying heating rate of 1 K min⁻¹, were analyzed and compared with that obtained by conventional DSC from the dependence of the fictive temperature on the cooling rate. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2272–2284, 2000     

Phase separation and polymer crystallization in a poly(4‐methyl‐1‐pentene)–dioctylsebacate–dimethylphthalate system via thermally induced phase separation

The effects of the polymer concentration and quenching temperature on the phase separation, the membrane morphology and polymer crystallization behavior in a poly(4‐methyl‐1‐pentene) (TPX)‐dioctylsebacate (DOS)‐dimethylphthalate (DMP) system via thermally induced phase separation were studied with a pseudobinary phase diagram, with the weight ratio of DOS:DMP = 1:1. SEM was used to observe the membrane morphology and structure, whereas the TPX crystallization behavior was studied with DSC and WAXD. Liquid‐liquid phase separation occurred, although quenching under the crystallization temperature. As the quenching temperature decreased, the pore size decreased, with better connected pore structure formed. The membranes quenched at 333 and 363 K showed good cellular structures, with an average pore size of about 2.3μm, whereas the pores of the membranes quenched at 393 and 423 K were not well formed, with some lamellar crystals on the inner side. The diluent assisted the mobility of the polymer chain, which improved the polymer crystallization. Dual‐melting‐peak behavior occurred for all the samples studied here. As the quenching temperature increased, the first peak of the melting trace moved to a higher temperature, whereas the second one stayed almost the same. The flexibility of the TPX main chain was restricted by the side groups, which allowed liquid‐liquid phase separation to occur first when quenched below the equilibrium crystallization temperature. This allowed primary and secondary crystallization, which was responsible for the dual‐melting‐peak behavior. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 153–161, 2007     

Isotactic polypropylene reversible crystallization investigated by modulated temperature and quasi‐isothermal FTIR

Modulated temperature techniques allow to separate the reversing and non‐reversing contributions of material transitions. To investigate reversible crystallization and melting of isotactic polypropylene (iPP) at microstructural level, in this research, modulated temperature Fourier transform infrared (MTFTIR) and quasi‐isothermal FTIR (QIFTIR) analyses are used. By following the intensity variation of iPP regularity bands, associated with 3₁ helix structures of different lengths (n repeating units), MTFTIR evidences that, independently from helix length, a reversing coil–helix transition takes place few degrees below the non‐reversing crystallization onset. By comparing spectroscopic and differential scanning calorimetry experiments performed in quasi‐isothermal conditions, the reversing transition was found to be associated with the reversible melting‐crystallization phenomenon. Moreover, QIFTIR evidences that helices of different lengths contribute differently to the reversible transition: the helices composed of n = 10 and n = 12 are active into all the explored temperature range (30–130 °C) whereas the shortest (n = 6) and the longest (n > 15) helices contribute to reversibility at T > 100 °C. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 922–931     

Effect of crystallization and liquid–liquid phase separation on phase‐separation kinetics in poly(ethylene‐co‐vinyl alcohol)/glycerol solution

Liquid–liquid thermally induced phase separation of the polymer‐diluent system of poly(ethylene‐co‐vinyl alcohol) (EVOH)‐glycerol was examined under light scattering. For EVOH with an ethylene content of 38 mol % (EVOH38), maxima of the scattered light intensity were observed that indicated that phase separation occurred by the spinodal decomposition (SD). The growth of the structures formed by the general liquid–liquid phase separation obeyed a power‐law scaling relationship in SD. For EVOH with an ethylene content of 32 mol % (EVOH32), the liquid–liquid phase separation resulted from the polymer crystallization. In this case, the structure growth showed the characteristic behavior in which the crystalline particles were initially formed, and then the droplets formed by the liquid–liquid phase separation induced by the crystallization grew rapidly. Furthermore, the growth of the droplet by the phase separation was followed by an optical microscope measurement at a constant cooling rate. The phase‐separated structure formed after the crystallization can grow faster than that formed by the normal liquid–liquid phase separation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 194–201, 2003