XPS and ToF‐SIMS characterization of a Finemet surface: effect of cooling

The surface composition of amorphous Finemet, Fe₇₃Si_15.8B_7.2Cu₁Nb₃, was studied by X‐ray photoelectron spectroscopy (XPS) and time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS). The as‐received sample in the original state and after Ar⁺ sputter‐cleaning was analyzed at room temperature as well as after cooling to ? 155 °C. In the cooled state, the surface oxide layer composed of oxides of the alloy constituents was found to become enriched with elemental iron and depleted of elemental silicon, boron, oxygen and carbon as compared to the state at room temperature. Interaction of residual water vapor and hydrogen with the complex oxide layer occurring at low temperatures is believed to be responsible for the enhanced formation of surface hydroxides of the alloy constituents. The processes resulting in the observed redistribution of the elements on the surface of Finemet at low temperatures are discussed. Copyright © 2006 John Wiley & Sons, Ltd.     

Surface studies of halloysite nanotubes by XPS and ToF‐SIMS

This report provides detailed experimental results of thermal and surface characterization on untreated and surface‐treated halloysite nanotubes (HNTs) obtained from two geographic areas. Surface characterization techniques, including XPS and time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) were used. ToF‐SIMS surface analysis experiments were performed with both atomic and cluster ion beams. Higher ion yields and more high‐mass ions were obtained with the cluster ion beams. Static ToF‐SIMS spectra were analyzed with principal component analysis (PCA). Morphological diversities were observed in the samples although they mainly contained tubular structures. Thermogravimetric data indicated that aqueous hydrogen peroxide solution could remove inorganic salt impurities, such as alkali metal salts. The amount of grafting of benzalkonium chloride of HNT surface was determined by thermogravimetic analysis. PCA of ToF‐SIMS spectra could distinguish the samples mined from different geographical locations as well as among surface‐treated and untreated samples. Copyright © 2010 John Wiley & Sons, Ltd.     

Quantitative analysis of styrene‐pentafluorostyrene random copolymers by ToF‐SIMS and XPS

Poly(styrene) (PS), poly(2,3,4,5,6‐pentafluorostyrene) (5FPS) and their random copolymers were prepared by bulk radical polymerization. The spin‐cast polymer films of these polymers were analyzed using X‐ray photoelectron spectroscopy (XPS) and time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS). The surface and bulk compositions of these copolymers were found to be same, implying that surface segregation did not occur. The detailed analysis of ToF‐SIMS spectra indicated that the ion fragmentation mechanism is similar for both PS and 5FPS. ToF‐SIMS quantitative analysis using absolute peak intensity showed that the SIMS intensities of positive styrene fragments, particularly C₇H₇⁺, in the copolymers are higher than the intensities expected from a linear combination of PS and 5FPS, while the SIMS intensities of positive pentafluorostyrene fragments are smaller than expected. These results indicated the presence of matrix effects in ion formation process. However, the quantitative approach using relative peak intensity showed that ion intensity ratios are linearly proportional to the copolymer mole ratio when the characteristic ions of PS and 5FPS are selected. This suggests that quantitative analysis is still possible in this copolymer system. Copyright © 2005 John Wiley & Sons, Ltd.     

XPS and ToF‐SIMS characterization of a Finemet surface: effect of heating

X‐ray photoelectron spectroscopy (XPS) and time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) were used to study the surface composition and electronic structure of Finemet, Fe₇₃Si_15.8B_7.2Cu₁Nb₃, in the original amorphous state and after gradual heating in vacuum to a temperature of 400 °C and cooling back to room temperature. It was found that relaxation processes occurring during heat treatment well below the crystallization onset caused the physico‐chemical state of Finemet surface to change irreversibly. In the relaxed alloy, the surface originally covered with the native air‐formed oxide was significantly enriched with elemental iron and depleted of other alloy constituents compared with the original state. Yet in the as‐quenched state, clustering of copper atoms on the Finemet surface was detected which was enhanced by heating. The thermal treatment resulted in the selective reduction of iron oxides and caused noticeable changes in the valence band structure and the Fe L₃VV Auger spectrum associated with atomic redistribution. Copyright © 2009 John Wiley & Sons, Ltd.     

ToF‐SIMS and XPS surface characterization of novel perfluoropolyether–urethane ionomers from aqueous dispersions

In this work a new class of ionomeric block perfluropolyether (PFPE) polyurethanes are presented; these polymers are obtained in the form of aqueous dispersions due to the presence of hydrophilic sites (ionomeric groups such as acetates or trialkylammonium salts) along the macromolecular chain, offering the chance to combine PFPEs in a variety of possible structures for coating or surface treatments with an environmentally friendly use. X‐ray photoelectron spectroscopy analysis at two different sampling depths, as well as time‐of‐flight secondary ion mass spectrometry analysis modelled by the use of principal component analysis (PCA), were used to investigate the first nanometres of the surface samples. It resulted in a clear surface enrichment in fluorine, and the different extent of the fluorine stratification will be discussed in relation to the ionic character, film‐forming from water and cross‐linking. Copyright © 2003 John Wiley & Sons, Ltd.     

Examination of the interface of a model adhesive joint by surface analysis: a study by XPS and ToF‐SIMS

Model samples of the interface of an adhesive joint containing small levels of aminopropyl triethoxysilane (APS) have been prepared in order to examine the interface formed with an aluminium substrate. X‐ray photoelectron spectroscopy (XPS) and time of flight secondary ion mass spectrometry (ToF‐SIMS) have been used to analyse and image the interface region in between the aluminium and an epoxy adhesive in order to ascertain the reactions by the organosilane which is present as a minor component within the system. It was found that APS was present at the interface between the adhesive and the substrate and that it had reacted with the substrate forming a covalent bond and was also crosslinked within the adhesive. Evidence of near to full hydrolysis of APS is also present within the spectra. Copyright © 2009 John Wiley & Sons, Ltd.     

ToF‐SIMS studies of the oxidation of Fe by D2O vapour: comparison with XPS

The oxidation of iron (Fe) by water (D₂O) vapour at low pressures and room temperature was investigated using time‐of‐flight (ToF) SIMS. The results supported those found previously using XPS and the QUASES^? program in that a duplex oxide structure was found containing a thin outer surface hydroxide (Fe(OD)₂) layer over an inner oxide (FeO) layer. The extraordinary depth resolution of the ToF‐SIMS profiles assisted in identifying the two phases; this resolution was achieved by compensation for surface roughness. A substantial concentration of deuterium was found in the subsurface oxide layer. This observation confirmed previous assessments that the formation of FeO was from the reaction of Fe(OD)₂ with outward‐diffusing Fe, leaving deuterium as a reaction product. Copyright © 2005 John Wiley & Sons, Ltd.     

Repair of defects created by Ar+ sputtering on graphite surface by annealing as confirmed using ToF‐SIMS and XPS

Defects were created on the surface of highly oriented pyrolytic graphite (HOPG) by sputtering with an Ar⁺ ion beam, then characterized using X‐ray photoelectron spectroscopy (XPS) and time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) at 500°C. In the XPS C1s spectrum of the sputtered HOPG, a sp³ carbon peak appeared at 285.3 eV, representing surface defects. In addition, 2 sets of peaks, the C_x⁻ and C_xH⁻ ion series (where x = 1, 2, 3...), were identified in the ToF‐SIMS negative ion spectrum. In the positive ion spectrum, a series of C_xH₂^+• ions indicating defects was observed. Annealing of the sputtered samples under Ar was conducted at different temperatures. The XPS and ToF‐SIMS spectra of the sputtered HOPG after 800°C annealing were observed to be similar to the spectra of the fresh HOPG. The sp³ carbon peak had disappeared from the C1s spectrum, and the normalized intensities of the C_xH⁻ and C_xH₂^+• ions had decreased. These results indicate that defects created by sputtering on the surface of HOPG can be repaired by high‐temperature annealing.     

Data and device protection: A ToF‐SIMS,wetting, and XPS study of an Apple iPod nano

An important aspect of the robustness of an electronic device is its ability to resist water, fingerprints, dirt, and smudges that may compromise its ability to function and/or the information within it. Here, we report a chemical analysis by ToF‐SIMS, wetting, and XPS of the surfaces in a commercially available Apple iPod nano (8GB, MC525LL/A), which showed good resistance to its environment. This analysis reveals that the front panel (touchscreen) of the device is coated with a low free energy fluorinated polymer that may consist of short segments of a fluorinated hydrocarbon connected through ether linkages. No other part of the device appears to have this hydrophobic coating. A plasma treatment of the device leads to a deterioration of its performance. This work demonstrates how different analytical techniques can complement each other and contribute to a better understanding of a surface or a material. Copyright © 2013 John Wiley & Sons, Ltd.     

Subsurface investigation of the surface modification of polydimethylsiloxane by 172‐nm vacuum ultraviolet irradiation using ToF‐SIMS and VUV spectrometry

We investigate the mechanism of polydimethylsiloxane (PDMS) surface modification by 172‐nm vacuum ultraviolet (VUV) light. Time‐of‐flight secondary ion mass spectrometry and optical spectrometry are used to measure the chemical composition and VUV transmittance of the PDMS before and after surface modification, respectively. For modified samples of bulk PDMS, the VUV transmittance and the depth of the modified region increased with increasing VUV dose. This can be explained by the following self‐reinforcing cycle of (1) modification of PDMS by VUV light to a more silica‐like composition, (2) improvement of the VUV light transparency, and (3) deeper modification. For thin‐film samples of PDMS formed on sapphire substrates, the transmittance at 172 nm also increased with increasing VUV dose and exceeded that of sapphire in the region from 172 to 300 nm. Finally, thin‐film samples of PDMS formed on silicon substrates, which function as a VUV reflector, were also investigated. For these samples, the secondary ion depth profiles for several chemical species in the PDMS were oscillatory, probably due to the interference of the incident and reflected VUV light. These results strongly suggest that the photon energy of the VUV light plays an important role in modifying PDMS.     

Investigation of Asian lacquer films using ToF‐SIMS and complementary analytical techniques

Lacquer has been used in Asian countries for thousands of years as a natural coating material owing to its durable, adhesive, decorative, and protective properties. Protection and restoration of lacquer‐coated cultural remains has become an important subject, and identification of the lacquer types in old lacquer‐wares has also become very important for conservation and restoration research. This paper provides identification of several molecular species of vegetal‐source Asian lacquers with the aim of providing a methodology for application in the field of cultural heritage. Several chemical markers of the vegetal species in Asian lacquers were identified using a methodology consistent with the sampling restrictions required for cultural‐heritage objects. Surface analytical methods such as time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS), X‐ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy were used to characterize Korean, Chinese, and Vietnamese lacquers; avoiding time‐consuming and destructive extraction processes. These ToF‐SIMS results provided the structural characterization of a series of catechol derivatives. The ToF‐SIMS spectra of Rhus vernicifera from Korea and China, and Rhus succedanea from Vietnam indicated a series of urushiol and laccol repeat units, respectively, in the mass range of m/z 0–1800. Because of its sensitivity, specificity, and speed of analysis, the ToF‐SIMS technique can be used to investigate cultural lacquer‐coated treasures as well as to discriminate among different Asian lacquer coatings or binding mediums for the conservation or restoration of lacquer‐ware. Copyright © 2016 John Wiley & Sons, Ltd.     

Extracting information on the surface monomer unit distribution of PLGA by ToF‐SIMS

The surface chemistry of a range of random poly l‐lactide‐co‐glycolide (PLGA) materials has been investigated using XPS, static secondary ion mass spectrometry (SSIMS) and gentle secondary ion mass spectrometry (G‐SIMS). The estimated mole fraction of lactide units provided by SSIMS was in good agreement with bulk composition and appeared not to have been affected by contamination. Conversely, XPS assessment of lactide compositions was unreliable due to hydrocarbon contamination contributions. In this study, we propose a novel model to demonstrate that by using SSIMS it is possible to infer the degree of trans‐esterification for PLGA co‐polymers synthesised from a mixture of lactide and glycolide homo‐dimers. This was determined by introducing two independent parameters, the ratio of trans‐esterified bonds to the total number of ester bonds, P_T, and the lactide composition. The model has indicated that, for this set of polymers, P_T was approximately 0.25. Furthermore, we have demonstrated that G‐SIMS successfully identified the structurally important key fragments leading to direct identification. Analysis by G‐SIMS showed that the glycolic acid units from all PLGA compositions are emitted in a lower energy‐fragmentation process than lactic acid units. Copyright © 2008 John Wiley & Sons, Ltd.     

Peak‐fitting of high resolution ToF‐SIMS spectra: a preliminary study

Peak‐fitting has been performed on a series of peaks obtained by time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) analysis in order to assess whether information may be obtained from this procedure on the samples' characteristics. A variety of samples were examined including a range of treatments for aluminium leading to different surface roughnesses, polymer films with a range of polydispersities, molecular weight (MW) and thicknesses as well as aluminium samples with adsorbed adhesion promoters on the surface. Variation of peak‐fitting was assessed by varying the peak intensity, full width at half maximum (FWHM) and peak asymmetry. Although further studies are needed it is possible to say that the peak width increases with roughness whereas peak asymmetry seems to be related to oxide thickness. Polymer characteristics do not seem to influence the width whereas the peak asymmetry increases either versus MW or polydispersity. A possible assumption is that the peak asymmetry relates to the ion formation processes. Additional work with varying polymer films thickness indicates that both FWHM and peak asymmetry may be related to sample charging and this could be used for assessment of film thicknesses. Finally, peak‐fitting was used to obtain a more reliable peak area when peaks are too close in mass to use current methods. Copyright © 2009 John Wiley & Sons, Ltd.     

ToF‐SIMS characterization of glyoxal surface oxidation products by hydrogen peroxide: A comparison between dry and liquid samples

As one of the simplest volatile organic compounds, glyoxal and its oxidation products were considered to be important precursors to aqueous secondary organic aerosol formation. Herein, we analyzed products from glyoxal oxidation by hydrogen peroxide in dry and liquid samples using time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS). ToF‐SIMS spectra and spectral principal component analysis (PCA) were used to investigate surface oxidation products. Dry samples were prepared on clean silicon wafers. Liquid samples consisting of glyoxal and hydrogen peroxide (H₂O₂) were introduced to a vacuum compatible microfluidic reactor prior to UV illumination or dark aging followed by in situ liquid SIMS analysis. A number of reaction products were observed in both dry and liquid samples; different oligomers and carboxylic acids could be formed depending on reaction conditions. In addition, hydrolyzed products were observed in the liquid samples, but not in the dry samples. Although dry samples reveal some products of the aqueous process, they are not fully representative as results from those of the aqueous samples. Our findings suggest that the ability to characterize the liquid surface reaction products provides more realistic information of the reaction products associated with aqueous secondary organic aerosol formation in the atmosphere. Meanwhile, the high mass resolution spectra from the dry sample SIMS measurement are helpful to identify oxidation products in the liquid samples.     

Characterization of size‐segregated aerosols using ToF‐SIMS imaging and depth profiling

Size‐segregated particles were collected with a ten‐stage micro‐orifice uniform deposit impactor from a busy walkway in a downtown area of Hong Kong. The surface chemical compositions of aerosol samples from each stage were analyzed using time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) operated in the static mode. The ToF‐SIMS spectra of particles from stage 2 (5.6–10 µm), stage 6 (0.56–1 µm), and stage 10 (0.056–0.1 µm) were compared, and the positive ion spectra from stage 2 to stage 10 were analyzed with principal component analysis (PCA). Both spectral analysis and PCA results show that the coarse‐mode particles were associated with inorganic ions, while the fine particles were associated with organic ions. PCA results further show that the particle surface compositions were size dependent. Particles from the same mode exhibited more similar surface features. Particles from stage 2 (5.6–10 µm), stage 6 (0.56–1 µm), and stage 10 (0.056–0.1 µm) were further selected as representatives of the three modes, and the chemical compositions of these modes of particles were examined using ToF‐SIMS imaging and depth profiling. The results reveal a non‐uniform chemical distribution from the outer to the inner layer of the particles. The coarse‐mode particles were shown to contain inorganic salts beneath the organics surface. The accumulation‐mode particles contained sulfate, nitrate, ammonium salts, and silicate in the regions below a thick surface layer of organic species. The nucleation‐mode particles consisted mainly of soot particles with a surface coated with sulfate, hydrocarbons, and, possibly, fullerenic carbon. The study demonstrated the capability of ToF‐SIMS depth profiling and imaging in characterizing both the surface and the region beneath the surface of aerosol particles. It also revealed the complex heterogeneity of chemical composition in size and depth distributions of atmospheric particles. Copyright © 2014 John Wiley & Sons, Ltd.     

Investigating the chain conformations of spin‐coated polymer thin films by ToF‐SIMS depth profiling

Thin films of bromine‐terminated poly(bisphenol A octane ether) (BA‐C10) were prepared using 1,2‐dichlorobenzene (ODCB) as the solvent. The organization of the chains in these amorphous polymer films was evaluated using time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) depth profiling. For the thin films, the bifunctional polymer chains were folded and anchored to the substrate via their two Br end groups and a polymer brush of chain loops was formed on the substrate. As the film thickness increased, polymer chains in a random coil conformation were found to reside on the top of the polymer brush. Depth profiling revealed that the polymer chains were densely packed at the interface. Moreover, the polymer films showed thermal stability, implying strong interactions between the end groups and the substrate. Copyright © 2015 John Wiley & Sons, Ltd.     

ToF‐SIMS observation of PTFE surfaces modified by α‐particle irradiation

The surface structure of polytetrafluoroethylene (PTFE) upon α‐particle irradiation has been investigated at doses in the range of 1 × 10⁷ to 1 × 10¹¹ Rad and compared with the surface structure of the unirradiated polymer. Both neat and 25% fiberglass content PTFE were studied. The samples, maintained at nominal room temperature, were irradiated in vacuum by 5.5 MeV ⁴He²⁺ ions generated in a tandem accelerator beam line. Static time‐of‐flight SIMS (ToF‐SIMS) was employed to probe chemical changes at the surface as a function of the irradiation level. In general, the data are indicative of increased cross‐linking at α‐doses less than 1 × 10⁹ Rad, followed by increased fragmentation and unsaturation at α‐doses greater than 1 × 10⁹ Rad. Throughout the irradiation regime, scission is a constant factor promoting cross‐linking, branching, and unsaturation. However, at α‐doses greater than 1 × 10¹⁰ Rad, extreme structural degradation of the polymer becomes evident and is accompanied by conversion to oxygen‐functionalized and aliphatic compounds. Thus, for PTFE in an α‐particle field, an upper exposure limit of ～10¹⁰ Rad is essential for nominal retention of molecular structure. Finally, a quantitative relationship between α‐dose and characteristic fragment ion intensity is developed. Copyright © 2005 John Wiley & Sons, Ltd.     

Fluorine plasma treatment of bare and nitrilotris(methylene)triphosphonic acid (NP) protected aluminum: an XPS and ToF‐SIMS study

Nitrilotris(methylene)triphosphonic acid (NP) is a technologically important molecule that has been used for years as a corrosion inhibitor and/or adhesion promoter on aluminum and other metal surfaces. However, to the best of our knowledge, the detailed surface characterization of NP adsorbed on aluminum, or on any other surface, has not been reported. Herein, we report an X‐ray photoelectron spectroscopy and time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) analysis of a series of untreated and NP‐coated aluminum substrates that were exposed to the downstream products of a fluoroalkane + oxygen plasma for different amounts of time (from 0 to 20 s). As indicated by P 2p, N 1s, Al 2p, O 1s, and F 1s narrow scans, even a 4‐s plasma treatment significantly damages the NP protective layer and converts the native aluminum oxide into aluminum oxyfluoride. Heat treatment of the fluorine plasma‐treated samples in the air substantially converts the aluminum oxyfluoride back to aluminum oxide, while similar heating under vacuum results in little change to the materials. A slow loss of fluorine from the samples occurs over the course of weeks when they are stored in the air. A ToF‐SIMS analysis reveals sets of signals that are consistent with no surface treatment, NP treatment, or fluorine plasma treatment. A principal component analysis of the negative ion ToF‐SIMS spectra from the samples shows the expected differentiation of the samples. Copyright © 2014 John Wiley & Sons, Ltd.     

Multivariate statistical analysis of non‐mass‐selected ToF‐SIMS data

Cluster LMIGs are now regarded as the standard primary ion guns on time‐of‐flight secondary ion mass spectrometers (ToF‐SIMS). The ToF‐SIMS analyst typically selects a bombarding species (cluster size and charge) to be used for material analysis. Using standard data collection protocols where the analyst uses only a single primary bombarding species, only a fraction of the ion‐beam current generated by the LMIG is used. In this work, we demonstrate for the first time that it is possible to perform ToF‐SIMS analysis when all of the primary ion intensity (clusters) are used; we refer to this new data analysis mode as non‐mass‐selected (NMS) analysis. Since each of the bombarding species has a different mass‐to‐charge ratio, they strike the sample at different times, and as a result, each of the bombarding species generates a spectrum. The resulting NMS ToF‐SIMS spectrum contains contributions from each of the bombarding species that are shifted in time. NMS spectra are incredibly complicated and would be difficult, if not impossible, to analyze using univariate methodology. We will demonstrate that automated multivariate statistical analysis (MVSA) tools are capable of rapidly converting the complicated NMS data sets into a handful of chemical components (represented by both spectra and images) that are easier to interpret since each component spectrum represents a unique and simpler chemistry. Copyright © 2008 John Wiley & Sons, Ltd.     

Effects of Ar‐ and Ar/O2‐plasma‐treated amorphous and crystalline polymer surfaces revealed by ToF‐SIMS and principal component analysis

The effects of argon (Ar) and a mixture of Ar and oxgyen(Ar/O₂) plasmas on amorphous and semi‐crystalline poly(bisphenol A hexane ether) thin films were investigated by time‐of‐flight secondary ion mass spectroscopy (ToF‐SIMS) and principal component analysis (PCA). PCA results of the ToF‐SIMS spectra indicate that an Ar/O₂ plasma produced less physical sputtering and had a higher chemical reactivity than did an Ar plasma, regardless of whether an amorphous or a crystalline surface was involved. However, the chemical differences between the Ar‐ and Ar/O₂‐plasma‐treated semi‐crystalline films were much smaller. The observed results can be explained by the higher resistance of the polymer crystalline regions to physical sputtering and chemical etching. Copyright © 2013 John Wiley & Sons, Ltd.