Barrier and Mechanical Properties of Poly(caprolactone)/organoclay Nanocomposites

In this study, biodegradable poly(caprolactone) (PCL) hybrids with two types of organoclays: Cloisite 30B (30B) and Cloisite 93A (93A) have been prepared by melt mixing and their barrier performance to air permeation and mechanical properties were investigated. The hybrids of PCL/30B were found to be nanocomposites resulted from the strong interaction between organic modifier of 30B and PCL and those of PCL/93A were microcomposites. The barrier performance of PCL/30B nanocomposite film to air permeation was much more improved than pure PCL and PCL/93A microcomposites at low organoclay concentration. With the increase of organoclay content the permeability coefficient was also increased that could attributed to the extra tortuous pathway for gas permeation caused by organoclay exfoliation. The barrier behaviour of PCL/30B nanocomposites could be approximately described by a theoretical model developed for composites. The mechanical properties measurements showed that the reinforcement of organoclay 30B in nanocomposites is more significant than 93A in microcomposites. Both tensile modulus and tensile strength were increased in PCL/30B nanocomposites even at at low amount of organoclay without much loss of strain at break as compared to pure PCL. The significant improvements in both barrier and mechanical properties in PCL nanocomposites could be attributed to the fine dispersion state of organoclay 30B platelets in PCL matrix and the strong interaction between organic modifier of 30B and matrix molecules.     

Solidlike transition of melt‐intercalated biodegradable polymer/clay nanocomposites

Synthetic biodegradable aliphatic polyester (BAP) intercalated into organoclay was prepared by melt compounding, and its solidlike characteristics were investigated via several rheological test modes: steady shear rotation, oscillation, and creep testing. Structural investigations with X‐ray diffraction and transmission electron spectroscopy were also performed for a better understanding of the characteristic rheological behaviors. The creep, recovery, and stress modulus exhibited a solidlike transition of BAP/clay nanocomposites that depended on the clay content. An increase in the zero shear rate viscosity and a shifting of the crossover point (storage modulus vs loss modulus) to a lower frequency were also observed with increasing clay contents. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2052–2061, 2003     

Poly(lactic acid)/organoclay nanocomposites: Thermal,rheological properties and foam processing

In this study, polymer nanocomposites based on poly(lactic acid) (PLA) and organically modified layered silicates (organoclay) were prepared by melt mixing in an internal mixer. The exfoliation of organoclay could be attributed to the interaction between the organoclay and PLA molecules and shearing force during mixing. The exfoliated organoclay layers acted as nucleating agents at low content and as the organoclay content increased they became physical hindrance to the chain mobility of PLA. The thermal dynamic mechanical moduli of nanocomposites were also improved by the exfoliation of organoclay; however, the improvement was reduced at high organoclay content. The dynamic rheological studies show that the nanocomposites have higher viscosity and more pronounced elastic properties than pure PLA. Both storage and loss moduli increased with silicate loading at all frequencies and showed nonterminal behavior at low frequencies. The nanocomposites and PLA were then foamed by using the mixture of CO₂ and N₂ as blowing agent in a batch foaming process. Compared with PLA foam, the nanocomposite foams exhibited reduced cell size and increased cell density at very low organoclay content. With the increase of organoclay content, the cell size was decreased and both cell density and foam density were increased. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 689–698, 2005     

Shear‐induced clay dispersion in HDPE/PEgMA/organoclay composites as studied via real‐time rheological method

In current study, a real‐time rheological method was used to investigate the intercalation and exfoliation process of clay in high‐density polyethylene/organoclay (HDPE/OMMT) nanocomposites using maleic anhydride grafted polyethylene (PEgMA) as compatibilizer. To do this, a steady shear was applied to the original nonintercalated or slightly intercalated composites prepared via simple mixing. The moduli of the composites were recorded as a function of time. The effect of matrix molecular weight and the content of compatibilizer on the modulus were studied. The role of the compatibilizer is to enhance the interaction between OMMT and polymer matrix, which facilitates the dispersion, intercalation, and exfoliation of OMMT. The matrix molecular weight determines the melt viscosity and affects the shear stress applied to OMMT platelets. Based on the experimental results, different exfoliation processes of OMMT in composites with different matrix molecular weight were demonstrated. The slippage of OMMT layers is suggested in low‐molecular weight matrix, whereas a gradual intercalation process under shear is suggested in high‐molecular weight matrix. Current study demonstrates that real‐time rheological measurement is an effective way to investigate the dispersion, intercalation, and exfoliation of OMMT as well as the structural change of the matrix. Moreover, it also provides a deep understanding for the role of polymer matrix and compatibilizer in the clay intercalation process. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 302–312, 2010     

Preparation and characterization of melt‐compounded polyethylene/vermiculite nanocomposites

Polyethylene (PE)‐layered vermiculite (VMT) nanocomposites were fabricated via direct melt compounding in a twin‐screw extruder followed by injection molding. Exfoliated PE/VMT nanocomposites were readily prepared via in situ melt mixing of maleic anhydride modified VMT with PE. Maleic anhydride acts as either the intercalation agent for VMT or as a compatibilizer for the PE and VMT phases. X‐ray diffraction and transmission electron microscopic observations revealed the formation of exfoliated PE/VMT nanocomposites. The experimental results showed that the storage modulus and strength of nanocomposites tend to increase with an increasing VMT content. Nearly 25.35% increment in the tensile strength and 50% increment in the storage modulus were achieved by incorporating 4 wt % VMT into PE. The thermal properties of the nanocomposites were investigated by dynamic mechanical analysis and differential scanning calorimetry. The glass‐transition temperature of PE/VMT nanocomposites appeared to increase upon the introduction of VMT into the PE matrix. The effects of maleic anhydride addition on the formation of the PE/VMT nanocomposites are discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1476–1484, 2003     

A new thermoplastic vulcanizate (TPV)/organoclay nanocomposite: Preparation,characterization, and properties

The preparation, characterization, and properties of the new thermoplastic vulcanizate (TPV)/organoclay nanocomposites are reported in this article. The nanocomposites were prepared by the melt intercalation method. The organoclay was first treated with glycidyl methacrylate, which acts as a swelling agent for organoclays, as well as a grafting agent for TPV (in the presence of dicumyl peroxide) during the melt mixing. The nanocomposite was intercalated, as evidenced by X‐ray diffraction. The tensile modulus of the 5% TPV/organoclay nanocomposite was higher than that of the 20% talc‐filled microcomposite. The storage modulus of the nanocomposite was higher than that of the pristine TPV. The most important observation is obtained from dynamic mechanical analysis, which reveals that the glass‐transition temperature of the polypropylene phase of the nanocomposite increases (as compared to virgin TPV), whereas the ethylene–propylene–diene monomer phase remains almost the same. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2900–2908, 2004     

Review of melt‐processed nanocomposites based on EVOH/organoclay

EVOH nanocomposites containing organically treated clays are unique systems in which the clay is strongly attracted to EVOH, thus affecting the morphology and the resultant thermal and mechanical properties. A strong effect of the processing conditions on morphology, thermal, and mechanical properties was observed. In highly interacting systems, under dynamic mixing conditions, in addition to a fracturing process of the clay particles, an onion‐like delamination process is suggested. EVA‐g‐MA and LLDPE‐g‐MA, having polar groups, were studied as compatibilizers to further induce clay intercalation and exfoliation. The compatibilizers affected both the thermal and mechanical properties of the composites at different levels. Thermal analysis showed that with increasing compatibilizer content lower crystallinity levels result, until at a certain content no crystallization has taken place. A Ny‐6 (nylon‐6)/EVOH blend is an interesting host matrix for incorporation of low organoclay contents. The Ny‐6/EVOH blend is a unique system that tends to hydrogen bond and also to in situ chemically react during melt mixing. The addition of clay seems to interrupt the chemical reaction between the two host polymers at certain compositions, leading to lower melt blending torque levels when clay is present. A competition between Ny‐6 and EVOH regarding the intercalation process takes place. However, Ny‐6 seems to lead to exfoliated structures, whereas EVOH forms intercalated structures, as revealed from combined XRD and TEM experiments, owing to thermodynamic considerations and preferential localization of the clay in Ny‐6. Of special interest is the increased storage modulus seen by the presence of only 1 wt % clay, which was achieved by extrusion under high shear forces, leading to a completely exfoliated structure. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1931–1943, 2005     

Synthesis,rheology, and morphology of nylon‐11/layered silicate nanocomposite

Exfoliated nylon‐11/layered silicate nanocomposites were prepared via in situ polymerization by dispersing organoclay in 11‐aminoundecanoic acid monomer. The original clay was modified by a novel method with 11‐aminoundecanoic acid. In situ Fourier transform infrared spectroscopy results show that stronger hydrogen bonds exist between nylon‐11 and organoclay than that of between nylon‐11 and original clay. The linear dynamic viscoelasticity of organoclay nanocomposites was investigated. Before taking rheological measurements, the exfoliated and intercalating structures and the thermal properties were characterized using X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry, and thermogravimetric analysis. The results show that the clay was uniformly distributed in nylon‐11 matrix during in situ polymerization of clay with 4 wt % or less. The presence of clay in nylon‐11 matrix increased the crystallization temperature and the thermal stability of nanocomposites prepared. Rheological properties such as storage modulus, loss modulus, and relative viscosity have close relationship with the dispersion favorably compatible with the organically modified clay. Comparing with neat nylon‐11, the nanocomposites show much higher dynamic modulus and stronger shear thinning behavior. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2161–2172, 2006     

Mechanical properties of polymer‐blend nanocomposites with organoclays: Polystyrene/ABS and high impact polystyrene/ABS

Thirty‐three polystyrene (PS)/acrylonitrile‐butadiene‐styrene (ABS) and high impact PS/ABS polymer blends with organoclay and copolymer additives were prepared by melt processing using different mixing sequences in order to test the putative capability of clay to perform a compatibilizing role in polymer blends. In general, the addition of clay increased the tensile modulus and had little effect on tensile strength. For the blends studied in this work, the addition of organoclays caused a catastrophic reduction in impact strength, a critical property for commercial viability. The polymer‐blend nanocomposites adopted a structure similar to that for ABS/clay nanocomposites as determined by X‐ray diffraction and transmission electron microscopy. It is suggested that clay reinforcement inhibits energy absorption by craze formation and shear yielding at high strain rates. Simultaneous mixing of the three components provided nanocomposites with superior elongation and energy to failure compared to sequential mixing. The clay pre‐treated with a benzyl‐containing surfactant gave the best overall properties among the various organoclays tested and of the two clay contents studied 4 wt % was preferred over 8 wt % addition. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

An observation of accelerated exfoliation in iPP/organoclay nanocomposite as induced by repeated shear during melt solidification

A well‐exfoliated morphology is usually observed for polar polymer/clay nanocomposites via dynamic melt processing techniques, whereas only an intercalated or a partially intercalated/partially exfoliated morphology is often obtained for nonpolar polymer/clay nanocomposites, even though some polar compatibilzer is used. In this study, an accelerated exfoliation effect was observed for the first time in iPP/organoclay nanocomposites prepared through so‐called dynamic packing injection molding, in which the specimen is forced to move repeatedly in a chamber by two pistons that move reversibly with the same frequency as the solidification progressively occurs from the mold wall to the molding core part. The disordered level and exfoliated degree of clay was found to dramatically increase from the skin to the core of the prepared samples and eventually the WAXD reflections of interlayer d‐spacing diminished in the core. The changed degree of exfoliation was also proved directly by TEM observation. The prolongation of processing time, the gradual growth of solidification front, the increased melts viscosity, and the shear amplification effect were considered to explain the higher degree of exfoliation in the center zone of mold chamber. Our result suggests that a critical shear force may be needed to break down clay into exfoliated structure. This can be also well used to explain at least partially the intercalated morphology, which is commonly observed for nonpolar polymer/clay nanocomposites via conventional processing. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2005–2012, 2005     

Rheology of nanocomposites

In this study, a methodology is developed for the quantitative characterisation of the nanofiller network in polymer nanocomposites via dynamic rheometry. Nanoclay-reinforced poly(ε-caprolactone) (PCL) nanocomposites were prepared by melt mixing. Frequency sweep experiments in the melt state display at low frequencies a solid-like elastic response that can be attributed to the formation of a physical nanofiller network. Combining a semi empirical model and the time–temperature superposition principle permits a reliable determination of the zero shear modulus that characterises the solid-like response of nanocomposites at low frequency, and which is related to the nanofiller dispersion.     

Combined effects of clay modifications and compatibilizers on the formation and physical properties of melt‐mixed polypropylene/clay nanocomposites

The melt mixing technique was used to prepare various polypropylene (PP)‐based (nano)composites. Two commercial organoclays (denoted 20A and 30B) served as the fillers for the PP matrix, and two different maleated (so‐called) compatibilizers (denoted PP‐MA and SMA) were employed as the third component. The results from X‐ray diffraction (XRD) and transmission electron microscope (TEM) experiments revealed that 190 °C was an adequate temperature for preparing the nanocomposites. Nanocomposites were achieved only if specific pairs of organoclay and compatibilizer were simultaneously incorporated in the PP matrix. For example, PP/20A(5 wt %)/PP‐MA(10 wt %) and PP/30B(5 wt %)/SMA(5 wt %) composites exhibited nanoscaled dispersion of 20A or 30B in the PP matrix. Differential scanning calorimetry (DSC) results indicated that the organoclays served as nucleation agents for the PP matrix. Generally, their nucleation effectiveness increased with the addition of compatibilizers. The thermal stability enhancement of PP after adding 20A was confirmed with thermogravimetric analysis (TGA). The enhancement became more evident as a suitable compatibilizer was further added. However, for the 30B‐included composites, thermal stability enhancement was not evident. The dynamic mechanical properties (i.e., storage modulus and loss modulus) of PP increased as the nanocomposites were formed; the properties increment corresponded to the organoclay dispersion status in the matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4139–4150, 2004     

Effect of a silicate filler on the crystal morphology of poly(trimethylene terephthalate)/clay nanocomposites

A series of intercalated poly(trimethylene terephthalate) (PTT)/clay nanocomposites were prepared in a twin‐screw extruder by the melt mixing of PTT with either quaternary or ternary ammonium salt‐modified clays. The morphology and structure, along with the crystallization and melting behavior, and the dynamic mechanical behavior of the composites were characterized by X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry, and dynamic mechanical thermal analysis. The results showed that the PTT chains could undergo center‐mass transport from the polymer melt into the silicate galleries successfully during the blending and extrusion process. More coherent stacking of the silicate layers was reserved at higher clay concentrations and shorter blend times. Compared with conventionally compounded composites, the nanoscale‐dispersed organophilic clays were more effective as crystal nucleation agents. The influence of the nanosilicates on the crystallization and melting behavior of PTT became distinct when the concentration of clay was around 3 wt %. The changes in the crystallization behavior of the polymer/clay nanocomposites depended not only on the size of the silicates but also on the intrinsic crystallization characteristics of the polymers. The resulting nanocomposites showed an increase in the dynamic modulus of PTT and a decrease in the relaxation intensity (both in loss modulus and loss tangent magnitude). © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2275–2289, 2003     

The influence of reactive organoclay on a biorenewable castor oil‐based polyurethane prepolymers toughened polylactide nanocomposites

Polylactide (PLA) is the most extensively reviewed and utilized biodegradable and renewable thermoplastic polyester, with potential to replace conventional petroleum‐based polymeric materials. To improve the toughness of PLA, castor oil‐based polyurethane prepolymer (COPUP) toughened PLA nanocomposites were prepared via the melt mixing process and investigated for its mechanical, thermal and morphological properties. X‐ray diffraction and transmission electron microscopy studies revealed the formation of polymer blend nanocomposites. Mechanical tests revealed optimum performance characteristics at PLA/COPUP ratio of 70:30. Further, loading of the organoclay showed higher tensile strength and modulus of the blend nanocomposites as compared to optimized blend. The morphological results indicated that the surface roughness increases as a function of the organoclay incorporation. Thermogravimetric measurements reveal that the thermal stability of the blend increases with the incorporation of organoclay. The improved mechanical properties along with its biodegradability might lead to new industrial and biomedical applications. Copyright © 2016 John Wiley & Sons, Ltd.     

Effect of silver nanoparticles on the dynamic crystallization behavior of nylon‐6

The effect of introducing silver nanoparticles on the rheological properties and dynamic crystallization behavior of nylon‐6 was investigated. The nanocomposites showed slightly higher viscosity than pure nylon‐6 in the low‐frequency range even at an extremely low loading level of the silver particles (0.5–1.0 wt %). The nanoparticles had a more noticeable effect on the storage modulus than on the loss modulus of a nylon‐6 melt and reduced its loss tangent. They increased the crystallization temperature of nylon‐6 by about 14 °C and produced a sharper crystalline peak. The silver nanoparticles promoted the crystallization of nylon‐6, and their effect on the dynamic crystallization of nylon‐6 at 200 °C was more notable at a lower shear rate and at 190 °C at a higher frequency. Nylon‐6 produced large spherulitic crystals, but the nanocomposites showed a grainy structure. In addition, the silver nanoparticles reduced the fraction of the α‐form crystal but increased that of the γ‐form crystal. The nanocomposites crystallized at 190 °C showed a lower melting temperature than nylon‐6 by about 3 °C, whereas the nanocomposites crystallized at 200 °C showed almost the same melting temperature. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 790–799, 2004     

Distributive mixing of carbon nanotubes in poly(caprolactone) via solution and melt processing: Viscoelasticity and crystallization behavior versus mixing indices

Different mixing processes give rise to significant differences in the agglomeration and deagglomeration of nanoparticles and how they are mixed and distributed within a polymeric matrix. Here poly(caprolactone), PCL, was compounded with carbon nanotubes, CNTs, at a weight fraction of 0.5% (volume fraction, Φ = 0.0027), using both solution and melt processing methods. Microscopy, image analysis, and thermogravimetric analysis, TGA, were used to define and characterize the distributions of the CNT‐rich domain sizes and to obtain quantitative mixing indices at different scales of examination. The presence of the CNTs led to the shear‐induced crystallization of PCL under conditions at which pure PCL would not crystallize and the microstructures obtained upon shear‐induced crystallization were documented via X‐ray diffraction, differential scanning calorimetry, and rheological characterization. Shear‐induced crystallization occurred at a faster rate (smaller induction times) when the nanocomposites exhibited greater mixing index values. The shear‐induced crystallization behavior was found to be a more sensitive indicator of the distributive mixing states of the CNTs in comparison with the widely used linear viscoelastic rheological material functions. The demonstrated methodologies can be used as complementary tools for processing and development of nanocomposites to achieve consistent and reproducible microstructures at various scales of examination and functional properties. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2254–2268.     

Effect of different matrices and nanofillers on the rheological behavior of polymer‐clay nanocomposites

In this work, a comprehensive study of the rheological behavior under shear and isothermal and nonisothermal elongational flow of low density polyethylene (LDPE) and ethylene‐vinyl acetate copolymer (EVA) based nanocomposites was reported to evaluate their “filmability”, that is, the ability of these material to be processed for film forming applications. The influence of two different kinds of organoclay – namely Cloisite 15A and Cloisite 30B – and their concentration was evaluated. The presence of filler clearly affects the rheological behavior in oscillatory state of polyolefin‐based nanocomposites but the increase of complex viscosity and the shear thinning are not dramatic. A larger strain‐hardening effect in isothermal elongational flow is shown by the nanocomposites compared to that of the pure matrix, particularly for EVA based nanocomposites. The melt strength measured under nonisothermal elongational flow increases in the presence of the nanofiller, while the drawability is only slightly lower than that measured for the neat matrix. Moreover, the rheological behavior under nonisothermal elongational flow of EVA‐based nanocomposites is similar for both nanoclays used. Differently, LDPE‐based nanocomposites show a strong dependence on the type of organoclay. Finally, the mechanical properties of the materials were measured by tensile tests. They revealed that the presence of the filler provokes, in all the cases, an increase of the rigidity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 344–355, 2010     

Thermal and mechanical properties of syndiotactic polystyrene/organoclay nanocomposites with different microstructures

The fabrication of syndiotactic polystyrene (sPS)/organoclay nanocomposite was conducted via a stepwise mixing process with poly(styrene‐co‐vinyloxazolin) (OPS), that is, melt intercalation of OPS into organoclay followed by blending with sPS. The microstructure of nanocomposite mainly depended on the arrangement type of the organic modifier in clay gallery. When organoclays that have a lateral bilayer arrangement were used, an exfoliated structure was obtained, whereas an intercalated structure was obtained when organoclay with a paraffinic monolayer arrangement were used. The thermal and mechanical properties of sPS nanocomposites were investigated in relation to their microstructures. From the thermograms of nonisothermal crystallization and melting, nanocomposites exhibited an enhanced overall crystallization rate but had less reduced crystallinity than a matrix polymer. Clay layers dispersed in a matrix polymer may serve as a nucleating agent and hinder the crystal growth of polymer chains. As a comparison of the two nanocomposites with different microstructures, because of the high degree of dispersion of its clay layer the exfoliated nanocomposite exhibited a faster crystallization rate and a lower degree of crystallinity than the intercalated one. Nanocomposites exhibited higher mechanical properties, such as strength and stiffness, than the matrix polymer as observed in the dynamic mechanical analysis and tensile tests. Exfoliated nanocomposites showed more enhanced mechanical properties than intercalated ones because of the uniformly dispersed clay layers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1685–1693, 2004     

Organo-modified montmorillonite/poly(?-caprolactone) nanocomposites prepared by melt intercalation in a twin-screw extruder

Nanocomposites based on biodegradable poly(?-caprolactone) organo-modified clay have been prepared by melt intercalation using a twin-screw extruder. The screw configuration developed allowed us to obtain an intercalated/exfoliated nanocomposite structure using a modified montmorillonite containing no polar groups, in contrast to previous work using mainly alkyl ammonium containing hydroxyl polar groups in poly(?-caprolactone). Montmorillonite nanocomposites were prepared using a specific extrusion profile from a 30 wt% masterbatch of organo-modified clay, which was then diluted at 1, 3 and 5%. Intercalated and/or exfoliated nanocomposites structures were assessed using rheological procedures and confirmed by transmission electron microscopy analysis. Mechanical and thermal properties were found to be strongly dependent on morphology and clay percentage. Crystallinity was only slightly affected by the clay addition. Effect of exfoliation on Young's modulus and thermal stability was investigated. Young's modulus increased significantly and onset degradation temperature measured by TGA was significantly reduced for an exfoliated nanocomposite composition containing 5 wt% organoclay.     

Rheological properties and crystallization behavior of multi‐walled carbon nanotube/poly(ε‐caprolactone) composites

Multi‐walled carbon nanotube/poly(ε‐caprolactone) composites (PCLCNs) were prepared by melt compounding. The rheology, nonisothermal crystallization behavior, and thermal stability of PCLCNs were, respectively, investigated by the parallel‐plate rheometer, differential scanning calorimeter, and TGA. Cole–Cole plots were employed successfully to detect the rheological percolation of PCLCNs under small amplitude oscillatory shear. PCLCNs present a low percolation threshold of about 2–3 wt % in contrast to that of clay‐based nanocomposites. The percolated nanotube network is very sensitive to the steady shear deformation, and is also to the temperature, which makes the principle of time‐temperature superposition be invalid on those percolated PCLCNs. Small addition of nanotube cannot improve the thermal stability of PCL but can increase crystallization temperature remarkably due to the nucleating effect. As the nanotube is much enough to be percolated, however, the impeding effect becomes the dominant role on the crystallization, and the thermal stability increases to some extent. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3137–3147, 2007