Novel cellulose derivatives. V. Synthesis and thermal properties of esters with trifluoroethoxy acetic acid

Esters of cellulose with trifluoroethoxy acetic acid (TFAA) were prepared in homogeneous phase using a mixed anhydride with p‐toluenesulfonic acid. Esters with low degree of substitution (DS), and with DS rising from 0 to 3, had hydrophobic character that prevented the usual association with moisture, which is otherwise typical of cellulose esters with low DS. Cellulose trifluoroethoxy acetate (CT) had T_g's declining by about 40 °C per DS‐unit (from 160 to 41 °C) as DS rose from 1 to 3. Mixed esters, cellulose derivatives with acetate and trifluoroethoxy acetate substituents (CAT), exhibited glass‐to‐rubber and melting transitions by DSC. A linear relationship between both T_g and T_m with respect to DS was recorded with the T_g and T_m separated by 30° to 40 °C. This is consistent with cellulose esters described elsewhere. Surprisingly, the T_g's of CT and CAT were found to be identical when the DS was equivalent to the DS of the fluoro substituents (DS_F). © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 486–494, 2000     

An Efficient Method for Determination of the Degree of Substitution of Cellulose Esters of Long Chain Aliphatic Acids

The determination of the degree of substitution (DS) of fatty acid cellulose esters, representing a broad range of substituents (C₆, C₁₂, C₁₈ and C₂₂), was performed by alkaline hydrolysis of the ester groups and the quantification of fatty acids by gas chromatography-mass spectrometry (GC-MS) as their trimethylsilyl derivatives. The method was optimized and compared with established techniques for the DS determination (elemental analysis and alkaline hydrolysis/titrimetry). The results demonstrated that alkaline hydrolysis/GC-MS is a rapid, reliable and powerful method for analysis of fatty acid cellulose esters, particularly when different acyl substituents are present.     

Ethylene polymerization by bis(salicylaldiminate)nickel(II)/aluminoxane catalysts

The homopolymerization of ethylene by using different catalytic systems based on dinitro‐substituted bis(salicylaldiminate)nickel(II) precursors such as bis[3,5‐dinitro‐N(2,6‐diisopropylphenyl)]nickel(II) and bis[3,5‐dinitro‐N(phenyl)]nickel(II) in combination with organoaluminum compounds was investigated. In particular, the catalytic performances were studied as a function of the main reaction parameters, such as temperature, pressure, Al/Ni molar ratio, and duration. Methylaluminoxane resulted in the best co‐catalyst. Activities up to 200 kg polyethylene/(mol Ni × h) to give a linear high‐molecular‐weight polymer were achieved. The influence of the bulkiness of the substituents on the N‐aryl group of the aldimine ligand was also checked; it resulted in a determinant for catalytic activity rather than for polymer characteristics. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2534–2542, 2004     

Self‐association of cellulose ethers with random and regioselective distribution of substitution

2 to 4% aqueous solutions of regioselectively substituted 3‐mono‐O‐ethyl‐ ( 3‐EC ) and randomly substituted ethyl‐ ( EC ) cellulose show association and gelation above 50–60 and 20–30 °C, respectively. In contrast, almost no association or gelation was seen with regioselectively substituted 3‐mono‐O‐methoxyethyl cellulose ( 3‐MEC ). This could be assessed by eye and measured using the techniques of ¹H high‐resolution nuclear magnetic resonance, oscillatory rheology, and micro‐differential scanning calorimetry (DSC). Several processes are thought to occur during association and gelation of EC and 3‐EC . These were separated with respect to temperature, to varying degrees, on cooling and have been modeled using DSC data. In accordance with other work in the literature, they are thought to be, on heating, the disassociation of structures in solution followed first by the formation of water cages and then by the association of hydrophobic moieties into a precipitate or gel. Contrasting with previous work (Haque and Morris, Carbohydr Polym 1993, 22, 161–173), the rheological measurements do not show “two distinct waves of structure formation” at the present concentrations and the DSC measurements show, on cooling, an extremely wide separation in temperature of the processes for the regioselectively substituted cellulose derivative 3‐EC . © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1743–1752, 2009     

Ethene homopolymerization and copolymerization with 1‐hexene for all methyl‐substituted (RnC5H5−n)2ZrCL2/MAO catalytic systems: Effects of split methyl substitution

Ethene homopolymerization and copolymerization with 1‐hexene were catalyzed by methyl‐substituted cyclopentadienyl (Cp) zirconium dichlorides, (R_n C₅H_5−n)₂ZrCl₂ (R_n = H, Me, 1,2‐Me₂, 1,3‐Me₂, 1,2,3‐Me₃, 1,2,4‐Me₃, Me₄, or Me₅), and methylaluminoxane. The polymers were characterized with Fourier transform infrared, nuclear magnetic resonance, gel permeation chromatography, and differential scanning calorimetry techniques. Generally, an increasing number of methyl substituents on the Cp ligand results in lower 1‐hexene incorporation in the copolymer. The two catalysts with split methyl substitution (R_n = 1,3‐Me₂ and R_n = 1,2,4‐Me₃) show a higher comonomer response than their disubstituted and trisubstituted counterparts (R_n = 1,2‐Me₂ and R_n = 1,2,3‐Me₃). They even incorporate more 1‐hexene than R_n = H and R_n = Me. These findings are qualitatively in agreement with the results of a theoretical study based on density functional calculations. The presence of comonomer does not influence the termination reactions after the insertion of ethene. There is more frequent termination after each hexene insertion with increasing comonomer incorporation except for the two catalysts with split methyl substituents. The termination probability per inserted comonomer is highest for the less substituted catalysts. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3161–3172, 2000     

Control of thermal,mechanical, and optical properties of three‐component maleimide copolymers by steric bulkiness and hydrogen bonding

N‐substituted maleimides polymerize in the presence of a radical initiator to give polymers with excellent thermal stabilities and transparency. In this study, we synthesized various maleimide copolymers with styrenes and acrylic monomers to control their thermal and mechanical properties by the introduction of bulky substituents and intermolecular hydrogen bonding. Three‐component copolymers of N‐(2‐ethylhexyl)maleimide in combination with styrene, α‐methylstyrene (MSt), or 1‐methylenebenzocyclopentane (BC5) as the styrene derivatives, and n‐butyl acrylate, 2‐hydroxyethyl acrylate, 4‐hydroxybutyl acrylate, or acrylic acid as the acrylic monomers were prepared by radical copolymerization. These copolymers were revealed to exhibit excellent heat resistance by thermogravimetric analysis. Glass transition temperatures increased by the introduction of bulky MSt and BC5 repeating units. The mechanical properties of the copolymer films were improved by the introduction of intermolecular hydrogen bonding. Optical properties, such as transmittance, refractive index, Abbe number, and birefringence, were determined for the copolymers. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1569–1579     

Substituent effect on azobenzene‐based liquid‐crystalline organophosphorus polymers

An Erratum has been published for this article in Journal of Polymer Science Part A: Polymer Chemistry (2003) 41(23) 3862 A new series of combined‐type, azobenzene‐based organophosphorus liquid‐crystalline polymers were synthesized, and their photoisomerization properties were studied. The prepared polymers contained azobenzene units as both the main‐chain and side‐chain mesogens. Various groups were substituted in the terminal of the side‐chain azobenzene mesogen, and the effects of the substituents were investigated. All the polymers were prepared at the ambient temperature by solution polycondensation with various 4‐substituted phenylazo‐4′‐phenyloxyhexylphosphorodichloridates and 4,4′‐bis(6‐hydroxyhexyloxy) azobenzene. The polymers were characterized with gel permeation chromatography, Fourier transform infrared, and ¹H, ¹³C, and ³¹P NMR spectroscopy. Thermogravimetric analysis revealed that all the polymers had high char yields. The liquid‐crystalline behavior of the polymers was examined with hot‐stage optical polarizing microscopy, and all the polymers showed liquid‐crystalline properties. The formation of a mesophase was confirmed by differential scanning calorimetry (DSC). The DSC data suggested that mesophase stability was better for electron‐withdrawing substituents than for halogens and unsubstituted ones. Ultraviolet irradiation studies indicated that the time taken for the completion of photoisomerization depended on the dipolar moment, size, and donor–acceptor characteristics of the terminal substituents. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3188–3196, 2003     

Isotactic polypropylene reversible crystallization investigated by modulated temperature and quasi‐isothermal FTIR

Modulated temperature techniques allow to separate the reversing and non‐reversing contributions of material transitions. To investigate reversible crystallization and melting of isotactic polypropylene (iPP) at microstructural level, in this research, modulated temperature Fourier transform infrared (MTFTIR) and quasi‐isothermal FTIR (QIFTIR) analyses are used. By following the intensity variation of iPP regularity bands, associated with 3₁ helix structures of different lengths (n repeating units), MTFTIR evidences that, independently from helix length, a reversing coil–helix transition takes place few degrees below the non‐reversing crystallization onset. By comparing spectroscopic and differential scanning calorimetry experiments performed in quasi‐isothermal conditions, the reversing transition was found to be associated with the reversible melting‐crystallization phenomenon. Moreover, QIFTIR evidences that helices of different lengths contribute differently to the reversible transition: the helices composed of n = 10 and n = 12 are active into all the explored temperature range (30–130 °C) whereas the shortest (n = 6) and the longest (n > 15) helices contribute to reversibility at T > 100 °C. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 922–931     

Dynamic mechanical behavior of fluorinated aromatic poly(ethers)

The relaxation behavior of six fluorinated aromatic poly(ethers) was investigated using dynamic mechanical analysis. The glass transition temperature was found to increase as the size and rigidity of linking groups increased and varied between 168°C for a dimethyl linking group and 300°C for a bicyclic benzoate ether-linking group. For the α-relaxation the steepness of time/temperature plots and broadness of the loss curves could be qualitatively correlated with chemical structure in a manner predicted by the coupling model of relaxation. Well-separated sub-T_g transitions were also observed, as a shoulder on the low temperature side of the α-peak, and as a broad, low loss transition around −100°C. The higher temperature process was similar to the structural relaxation often found in quenched glassy polymers, while the position, intensity, and breadth of the subambient process was sensitive to chemical structure. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 1963–1971, 1997     

Influence of alkoxy tail length and unbalanced mesogenic core on phase behavior of mesogen‐jacketed liquid crystalline polymers

When the flexible terminal substituent changes from butoxy to hexyloxy or longer, smectic C (S_C) liquid crystalline phase was firstly reported to develop from a kind of mesogen‐jacketed liquid crystalline polymer (MJLCP) whose mesogenic side groups are unbalancedly bonded to the main chain without spacers. A series of MJLCPs, poly[4,4′‐bis(4‐alkoxyphenyl)‐2‐vinylbiphenyl(carboxide)] (nC2Vp, n is the number of the carbons in the alkoxy groups, n = 2, 4, 6, 8, 10, and 12) were designed and synthesized successfully via free radical polymerization. The molecular weights of the polymers were characterized with gel permeation chromatography, and the liquid crystalline properties were investigated by differential scanning calorimetry, polarized light microscopy experiments, and 1D, 2D wide‐angle X‐ray diffraction. Comparing with the butoxy analog, the polymer with unbalanced mesogenic core and shorter flexible substituents (n = 2, 4) keeps the same smectic A (S_A) phase, but other polymers with longer terminal flexible substituents (n = 6, 8, 10, and 12) can develop into a well‐defined S_C phase instead of S_A phase. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 505–514, 2009     

Effects of Chain Ends on Thermal and Mechanical Properties and Recyclability of Poly(γ-butyrolactone)

This work investigates effects of poly(γ-butyrolactone) (PγBL) with different initiation and termination chain ends on five types of materials properties, including thermal stability, thermal transitions, thermal recyclability, hydrolytic degradation, and dynamic mechanical behavior. Four different chain-end-capped polymers with similar molecular weights, BnO-[C(=O)(CH₂)₃O]_n-R, R = C(=O)Me, C(=O)CH=CH₂, C(=O)Ph, and SiMe₂CMe₃, along with a series of uncapped polymers R′O-[C(=O)(CH₂)₃O]_n-H (R′ = Bn, Ph₂CHCH₂) with M_n ranging from low (4.95 kg mol⁻¹) to high (83.2 kg mol⁻¹), have been synthesized. The termination chain end R showed a large effect on polymer decomposition temperature and hydrolytic degradation, relative to H. Overall, for those properties sensitive to the chain ends, chain-end capping renders R-protected linear PγBL behaving much like cyclic PγBL. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2271–2279     

Olefin metathesis applied to cellulose derivatives—Synthesis,analysis, and properties of new crosslinked cellulose plastic films

New crosslinked cellulose‐based plastic films were synthesized with olefin metathesis as a crosslinking reaction. Microcrystalline cellulose was first dissolved in a lithium chloride/N,N‐dimethylacetamide solvent system and acylated by ω‐undecenoyl chloride under microwave irradiation with N,N‐dimethyl‐4‐aminopyridine as the catalyst. Cellulose unsaturated fatty acyl esters with a degree of substitution (DS) ranging from 1.4 to 2.0 were then crosslinked by olefin metathesis with a first generation Grubbs catalyst. Crosslinking ratios (T) ranging from 20 to 90% were obtained for low catalyst amounts (<1.2%), but gels appeared when T was too high. To avoid this gel formation, cellulose was acylated with a mixture of lauroyl and ω‐undecenoyl chlorides. This internal dilution allowed us to obtain films of every case and various T (varying from 10 to 80% for a catalyst amount below 3.5%). Plastics were characterized by Fourier transform infrared (FTIR) spectroscopy, and the fatty acid mixture resulting from the hydrolysis of cellulose esters were analyzed by gas chromatography (GC) and NMR spectroscopy. Mechanical properties showed that the elastic modulus and tensile failure stress was higher when the plastic films were crosslinked. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 407–418, 2005     

Synthesis,thermal characterization,and tensile properties of alipharomatic polyesters derived from 1,3‐propanediol and terephthalic,isophthalic, and 2,6‐naphthalenedicarboxylic acid

In this work, three alipharomatic polyesters—poly(propylene terephthalate) (PPT), poly(propylene isophthalate) (PPI), and poly(propylene naphthalate) (PPN)—were prepared and studied with the aliphatic diol 1,3‐propanediol and the corresponding aromatic diacids. Their synthesis was performed by the two‐stage melt polycondensation method in a glass batch reactor. The thermal characterization of these polyesters was carried out with different thermal techniques such as simultaneous thermogravimetry/differential thermal analysis, thermomechanical analysis (TMA), and dynamic thermomechanical analysis. From the recorded values for the glass‐transition temperature (T_g) and melting temperature with all the aforementioned techniques, it could be said that they were in good agreement. According to the thermogravimetric results, PPT and PPI showed about the same thermal stability, whereas PPN seemed to be somewhere more thermostable. Remarkably, a transition existed immediately after T_g that was realized by the first derivative of TMA, and it was characterized as a midrange transition. For all polyesters, the average coefficient of linear thermal expansion was calculated with TMA. The secondary relaxations T_β and T_γ, recorded with dynamic mechanical thermal analysis, were mainly affected by the kinds of monomers. Concerning the mechanical properties, PPN had the highest tensile strength at break, whereas PPT had the highest elongation at break. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3998–4011, 2005     

Degradable cellulose‐based polymer brushes with controlled grafting densities

Cellulose‐based polymer brushes with variable grafting densities and low dispersity were synthesized by grafting poly(n‐butyl acrylate) (PBA) side chains from cellulose‐derived backbones via ATRP. Esterification of commercially available cellulose acetate with 2‐bromoisobutyryl bromide (2‐BiBB) in NMP provided cellulose‐based macroinitiators averaging one initiation site per double glucose unit. ATRP macroinitiators averaging up to 6 initiation sites per repeating double glucose unit were prepared by acylation of microcrystalline cellulose (MCC) in LiCl/DMAc solvent system with 2‐BiBB. A series of linear macroinitiators with narrow MWD were obtained by fractional precipitation process. The content of initiating sites was determined by elemental analysis. (Meth)acrylate side chains were then grafted from the cellulose‐based macroinitiators. The prepared cellulose‐based polymer brushes showed tunable degradation rates dependent on grafting density of the brush, following two different degradation pathways, either cleavage of the main chain or detachment of the side chains. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2426–2435     

Preparation and characterization of cellulose β-ketoesters prepared by homogeneous reaction with alkylketene dimers: comparison with cellulose/fatty acid esters

Cellulose was dissolved in lithium chloride/1,3-dimethyl-2-imidazolidinone (LiCl/DMI), and reacted with alkylketene dimers (AKDs) under non-aqueous and homogeneous conditions to prepare cellulose/AKD β-ketoesters with high degrees of substitution (DS). Six AKDs synthesized from octanoic, decanoic, dodecanoic, tetradecanoic, hexadecanoic and octadecanoic acids via their fatty acid chlorides were used in this study. The cellulose/AKD β-ketoesters obtained were gummy solid at room temperature, and had DS values ranging from 1.9 to 2.9. Cellulose/fatty acid esters with DS 2.5–2.9 were also prepared as references. ¹³C-NMR spectra of the cellulose/AKD β-ketoesters showed that cellulose carbons and substituent carbons close to cellulose chains were restricted in motion and behaved like solid in solutions. In contrast, the cellulose/fatty acid esters did not demonstrate such anomalous ¹³C-NMR spectra. The unique ¹³C-NMR patterns are characteristic for the cellulose/AKD β-ketoesters, which have long and branched alkyl substituents in each anhydroglucose unit. Size-exclusion chromatography furnished with multi-angle laser light scattering (SEC-MALLS) revealed, on the other hand, that all cellulose/AKD β-ketoesters and cellulose/fatty acid esters prepared had flexible or random-coil conformations in tetrahydrofuran (THF). There were no clear differences in conformation or stiffness of cellulose chains between cellulose/AKD β-ketoesters and cellulose/fatty acid esters.     

Molecular mobility of substituted poly(p-phenylenes) characterized by a range of polymer relaxation techniques

The free volume and related mobility properties of substituted poly(p-phenylene) polymers are examined. The techniques used range from positron annihilation, dielectric relaxation, and dynamic mechanical spectroscopy to thermally stimulated currents. Fractional free volume is determined for the samples with different substituted side groups and related to the glass transition temperature. Bulkier groups lead to a greater fractional free volume and lower glass transition temperatures. Comparison of molecular relaxation times using the different characterization techniques demonstrates that there is strong coupling between motion of the main chain and the side groups, on which the dipoles reside. Intermolecular coupling between the main chains at the primary relaxation is shown in this work to be related to the nature of the side chains and resultant free volume, as are the temperature locations of local, secondary relaxations. A qualitative model describing the effect of regiochemistry on the motions and packing of these materials is also proposed. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1465–1481, 1998     

Preparation and thermal properties of asymmetrically substituted poly(silylenemethylene)s

Poly(silylenemethylene)s of the types [SiMeRCH₂]_n and [SiHRCH₂]_n were prepared by the ring-opening polymerization (ROP) of 1,3-disilacyclobutanes (DSCBs) containing n-alkyl substituents, such as C₂H₅, n-C₃H₇, n-C₄H₉, n-C₅H₁₁, and n-C₆H₁₃, or a phenyl group on the Si. These new polymers include a monosilicon analog of poly(styrene), [SiHPhCH₂]_n. Improved synthesis routes to the DSCB monomers were developed which proceed through Grignard ring closure reactions on alkoxy-substituted chlorocarbosilanes. All of these asymmetrically substituted polymers were obtained in high molecular weight form, except for [SiHPhCH₂]_n. The configurations of all of the polymers were found to be atactic. The aryl-substituted polymers have higher glass transition temperatures (T_gs) and thermal stability than those of the alkyl-substituted poly(silylenemethylene)s. Unlike the polyolefins of the type [C(H)(R)CH₂]_n, where T_g drops continuously from R = Me to n-Hex, the T_gs of the n-C_nH_2n+1 (n = 2–6)-substituted [SiMeRCH₂]_n PSM's appear to reach a maximum (at −61°C) for the R = n-Pr-substituted polymer. Moreover, where it was possible to make direct comparisons among similarly substituted atactic polymers, all of the poly(silylenemethylene)s were found to have lower T_gs than their all-carbon analogs. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3193–3205, 1997     

Propylene polymerization by C1‐symmetric {ONNO′}‐type salan zirconium complexes

The activities of C₁‐symmetric dibenzyl zirconium complexes of Salan ligands that bear a halo‐substituted phenolate ring and an alkyl‐substituted phenolate ring in propylene polymerization with methylaluminoxane as cocatalyst were studied. These {ONNO′}ZrBn₂‐type catalysts exhibited moderate‐to‐high activities and yielded polypropylene of low molecular weight. The degree of tacticity was found to depend on the steric bulk of the substituents on both phenolate rings and ranged from practically atactic to substantially isotactic (74–78% [mmmm] for polymerizations at room temperature by Lig⁵ZrBn₂). Hemi‐isotactic polypropylene was not obtained, despite the diastereotopicity of the two positions. The pattern of stereo errors was consistent with the enantiomorphic site control of propylene insertion typically observed for C₂‐symmetric catalysts and implied a facile site‐averaging mechanism. A regular 1,2‐insertion and a β‐H transfer to an incoming monomer correspond to the main propagation and termination processes, respectively. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and fluorescent properties of model compounds for conjugated polymer containing maleimide units at the main chain

2,3‐Diaryl substituted maleimides as model compounds of conjugated maleimide polymers [poly(RMI‐alt‐Ar) and poly(RMI‐co‐Ar)] were synthesized from 2,3‐dibromo‐N‐substituted maleimide (DBrRMI) [R= cyclohexyl (DBrCHMI) and n‐hexyl (DBrHMI)] and aryl boronic acid using palladium catalysts. To clarify structures of conjugated polymer containing maleimide units at the main chain, ¹³C NMR spectra of 2‐aryl or 2,3‐diaryl substituted maleimides were compared with those of N‐substituted maleimide polymers. Copolymers obtained with DBrRMI via Suzuki‐Miyaura cross‐coupling polymerizations or Yamamoto coupling polymerizations were dehalogenated structures at the terminal end. This dehalogenation may contribute to the low polymerizability of DBrRMIs. On the other hand, the π‐conjugated compounds showed high solubility in common organic solvents. The N‐substituents of maleimide cannot significantly affect the photoluminescence spectra of 2,3‐diaryl substituted maleimides derivatives. The fluorescence spectra of poly(RMI‐alt‐Ar) and poly(RMI‐co‐Ar) varied with N‐substituents of the maleimide ring. When exposed to ultraviolet light of wavelength 352 nm, a series of 1,4‐phenylene‐ and/or 2,5‐thienylene‐based copolymers containing N‐substituted maleimide derivatives fluoresced in a yellow to blue color. It was found that photoluminescence emissions and electronic state of π‐conjugated maleimide derivatives were controlled by aryl‐ and N‐substituents, and maleimide sequences of copolymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

NMR investigation of effect of dissolved salts on the thermoresponsive behavior of oligo(ethylene glycol)‐methacrylate‐based polymers

The synthesis of thermo‐ and ionic‐responsive copolymers based on polyethylene glycol methyl ether methacrylate (OEGMA) and 2,2,2‐trifluoroethyl acrylate (TFEA) via reversible addition‐fragmentation chain transfer polymerization is described. Reactivity ratios for the copolymerization of OEGMA and TFEA are r_OEGMA = 2.46 and r_TFEA = 0.22, indicating that OEGMA is incorporated more rapidly than TFEA monomers. The copolymers are thermosensitive and exhibit volume phase transitions (lower critical solution behavior) at temperature, which depend on copolymer composition and the presence of added salts in the aqueous solutions. It was found that the copolymers exhibited LCST transitions at temperatures below 353 K only in salt solutions. ¹H NMR measurements indicated that motion of the protons located in and near the hydrophobic main chain are more sensitive to temperature than protons in the hydrophilic OEGMA side chains. The hydrophilic side chains remain largely hydrated; however, the presence of two distinct conformations of the terminal groups of the side chains was confirmed. The influence of OEGMA side chain length, copolymer composition, and salt type on aggregation behavior and dynamics was examined in detail. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2375–2385