On the existence of phases with a structure of NaZr2(PO4)3 in series of binary orthophosphates with different alkaline element to zirconium ratios

Complex phosphates M_xZr_2.25–0.25x(PO₄)₃, where M=Li, Na,K, Rb or Cs and x may be an integer or fraction from 0 to 9, have been synthesized, and their structure has been investigated. The concentration and temperature ranges of stability of the phosphate phases NaZr₂(PO₄)₃ have been found. The influence of the method for the synthesis of these phases and of the annealing temperature on their crystal properties is studied. It was found that the structure of NaZr₂(PO₄)₃ [NZP] exists in the above phosphate series when 0≤x≤5 for Na and K, 0≤x≤3 for Rb, and 0≤x≤1 for Cs. N. I. Lobachevskii Nizhnii Novgorod State University. Translated fromZhurnal Strukturnoi Khimii, Vol. 37, No. 6, pp. 1104–1113, November–December, 1996. Translated by L. Smolina     

Synthesis and thermal characterization of NZP compounds Na1?xLixZr2(PO4)3 (x?=?0.00–0.75)

Sodium zirconium phosphate (NZP) composition Na_1−x Li _x Zr₂(PO₄)₃, x = 0.00–0.75 has been synthesized by method of solid state reaction method from Na₂CO₃·H₂O, Li₂CO₃, ZrO₂, and NH₄H₂PO₄, sintering at 1050–1250 °C for 8 h only in other to determine the effect on thermal properties, such as the phase formation of the compound. The materials have been characterized by TGA and DTA thermal analysis methods from room temperature to 1000 °C. It was observed that the increase in lithium content of the samples increased thermal stability of the samples and the DTA peaks shifted towards higher temperatures with increase in lithium content. The thermal stability regions for all the sample was observed to be from 640 °C. The sample with the highest lithium content, x = 0.75, exhibited the greatest thermal stability over the temperature range.     

Synthesis of continuous substitutional solid solutions M1?xNix(H2PO4)2 · 2H2O with M = Mg, Mn, Co, or Zn

New continuous substitutional solid solutions Mg_1−x Ni _x (H₂PO₄)₂ · 2H₂O, Mn_1−x Ni _x (H₂PO₄)₂ · 2H₂O, Co_1−x Ni _x (H₂PO₄)₂ · 2H₂O, and Zn_1−x Ni _x (H₂PO₄)₂ · 2H₂O (0 ≤ x ≤ 1.00) crystallizing in monoclinic space group P2₁/n have been synthesized. Their end-member is Ni(H₂PO₄)₂ · 2H₂O. Ni(H₂PO₄)₂ · 2H₂O is isostructural to magnesium, manganese, iron, cobalt, zinc, and cadmium dihydrogenphosphates. The chemical composition and the unit cell parameters have been determined for the solid solutions. Their IR spectra have been measured. Original Russian Text ? V.N. Viter, P.G. Nagornyi, 2007, published in Zhurnal Neorganicheskoi Khimii, 2007, Vol. 52, No. 1, pp. 19–25.     

Phase Analysis and Crystallographic Properties of the Phosphate Systems MO-ZrO2-P2O5 (M=Mg,Ca, Sr or Ba)

Phase formation in the systems MO-ZrO₂-P₂O₅ (M=Mg, Ca, Sr or Ba) with various ratios of M to Zr cations and within the temperature interval from 20 to 1200°C was investigated by means of DTA, TG, XRD and IR spectroscopy. The orthophosphate phases M_0.5xZr_2.25−0.25x(PO₄)₃ with x=0−1, 3 and 7 were synthesized. Concentration and temperature limits of phase existence were found for phosphates belonging in the NaZr₂(PO₄)₃ structural family. They exist within the regions with M to Zr ratios of 0≤x≤1 (with the exception of the Mg phases) and in the temperature interval from room temperature to 900–1700°C. This revised version was published online in August 2006 with corrections to the Cover Date.     

Hydrothermal alteration of BaxMIVxCe2?2 x (PO4)2 [MIV=Zr, Hf] as hosts for minor actinides

Ba_xM^IV _xCe_2−2x (PO₄)₂ [M^IV=Zr, Hf] monazite-like compounds were succesfully synthesized by solid state reaction for x≤0.2 (M^IV=Zr) and x≤0.1 (M^IV=Hf). The low miscibility of BaM^IV(PO₄)₂ (M^IV=Zr, Hf) compounds in CePO₄ was explained on the basis of the monoclinic-to-trigonal phase transition that occurs at 733 K in BaZr(PO₄)₂ and at 798 K in BaHf(PO₄)₂. The hydrothermal alteration of these compounds was tested using a modified MCC-1 static leaching test in acid (1 mol·dm⁻³ HCl) and basic (1 mol dm⁻³ KOH) solutions at 373 K, 473 K and 573 K; both the experimental fluids and the reacted solid specimens were analyzed by different analytical techniques and the reaction mechanisms were elucidated. All the tested compounds are stable in 1 mol·dm⁻³ HCl until 573 K. The stability of the monazites in 1 mol·dm⁻³ KOH is a function of the temperature.     

Composition and formation kinetics of strontium polyvanadates in vanadium(IV,V) solutions

The phase and chemical compositions of the precipitates forming in the Sr(VO₃)₂-VOCl₂-H₂O system in the V⁴⁺/V⁵⁺ = 0.11–9 range at 80–90°C are reported. At pH 1–3 and V⁴⁺/V⁵⁺ = 0.25−9, the general formula of the precipitated compounds is Sr _x V _y ⁴⁺ V_12−y ⁵⁺O_31−δ·nH₂)(0.37 ≤ x ≤ 1.0, 1.7 ≤ y ≤ 3.0, 0.95 ≤ δ ≤ 2.1). Polyvanadates containing the largest amount of vanadium(IV) are obtained at an initial V⁴⁺/V⁵⁺ ratio of 9 and pH 1.9. Precipitation from solutions at pH 3 takes place only in the presence of the VO²⁺ ion, and the highest precipitation rate is observed at V⁴⁺/V⁵⁺ = 0.11. The process is controlled by a second-order reaction on the polyvanadate surface. Under hydrothermal conditions at 180°C, Sr_0.25V₂O₅·1.5H₂O nanorods are obtained from solutions with a V⁴⁺/V⁵⁺ molar ratio of 0.1 at pH 3. The nanorods, 30–100 nm in diameter and up to 2–3 μm in length, have a layered structure with an interlayer spacing of 10.53 ± 0.08 ?.     

Thermal properties of Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–PbO–P<Subscript>2</Subscript>O<Subscript>5</Subscript> glass system

Thermal behavior of xGa₂O₃–(50 − x)PbO–50P₂O₅ (x = 0, 10, 20, and 30 mol.% Ga₂O₃) and xGa₂O₃–(70 − x)PbO–30P₂O₅ (x = 0, 10, 20, 30, and 40 mol.% Ga₂O₃) glassy materials were studied by thermo-mechanical analysis (TMA) and differential thermal analysis (DTA). Replacement of PbO for Ga₂O₃ is accompanied by increasing glass-transition temperature (263 ≤ T _g/°C ≤ 535), deformation temperature (363 ≤ T _d/°C ≤ 672), crystallization temperature (396 ≤ T _c/°C ≤ 640) and decreasing of coefficient of thermal expansion (5.1 ≤ CTE/ppm K⁻¹ ≤ 16.7). Values of Hruby parameter were determined (0.1 ≤ K _H ≤ 1.3). The thermal stability of prepared glasses increases with increasing of concentration of Ga₂O₃.     

1A1 5T2 Spin transition in the solid phases of FexNi1-x(ATr)3(NO3)2 (ATr = 4- amino- 1,2,4- triazole)

The effect of Fe²⁺ substitution by Ni²⁺ in the complex of iron(II) nitrate with 4- amino- 1,2,4- triazole Fe(ATr)₃(NO₃)₂ on the character of the¹A₁ ⁵T₂ spin transition (ST) is studied by magnetic susceptibility and calorimetry methods. Solid phases of Fe_xNi_{1- x}(ATr)₃(NO₃)₂ (0.1 ≤ x ≤ 0.9) were synthesized. The temperature dependences of the effective magnetic moment were measured in the range of 78– 360 K. Heat capacities were measured in the range of 210– 340 K for 0.1 ≤ x ≤ 0.5 and in the range of 230– 340 K for 0.6 ≤x ≤ 0.9. As x decreases, the transition temperature (T_C), hysteresis (δT_C, and transition enthalpy (δH) decrease and the ST is leveled. The results are compared with the data obtained previously for the solid phases of Fe_xZn_{1- x}(ATr)₃(NO₃)₂ (0.01 ≤ x ≤ 0.8). The dependence Μ_eff(T) is analyzed theoretically in terms of both the domain model and the spin equilibrium model. Translated fromZhumal Strukturnoi Khimii, Vol. 38, No. 4, pp. 696–703, July–August, 1997.     

Synthesis and thermolysis of substitutional solid solutions (Cu1?yMy)2(OH)PO4·xH2O (x = 0.1?0.2; M = Zn, Co, Ni)

Substitutional solid solutions (Cu_1−y Zn _y )₂(OH)PO₄·xH₂O (0 ≤ y ⩽ 0.26, x = 0.1−0.2), (Cu_1−y Co _y )₂(OH)PO₄·xH₂O (0 ≤ y ≤ 0.10, x = 0.1−0.2), and (Cu_1−y Ni _y )₂(OH)PO₄·xH₂O (0 ≤ y ≤ 0.08, x = 0.1−0.2) were synthesized. The unit cell parameters of the resulting phosphates were determined, and their IR absorption spectra were measured. The reactants were H3PO4 and mixtures of hydrous carbonates of the appropriate metals. Thermolysis of the solid solutions was examined with (Cu_1−y Co _y )₂(OH)PO₄·xH₂O (0 ≤ y ≤ 0.10, x = 0.1−0.2) as an example.     

Hydrolytic precipitation of magnesium polyvanadates in vanadium (IV, V) solutions

The phase and chemical composition of precipitates formed in Mg(VO₃)₂-VOSO4-H₂O system at initial pH from 1 to 7 and temperature from 80 to 90°C was studied. Polyvanadates of variable composition Mg _x V _y ⁴⁺V_12-y ⁵⁺¹O_31–δ · nH₂O (0.7 ≤ x ≤ 1.3, 1.2 ≤ y ≤ 2.4, 0.7 ≤ δ = 1.4) were formed at pH from 1 to 4 and V⁴⁺/V⁵⁺ ratio from 0.43 to 9. Compounds with the general formula Mg _x V _y ⁴⁺V_6-y ⁵⁺O_16-δ · nH₂O (0.7 ≤ x ≤ 0.65, y = 1.0, 0.8 ≤ δ ≤ 0.85) were formed at pH from 6.0 to 7.0 and V⁴⁺/V⁵⁺ ratios from 0.11 to 0.25. The maximum V⁴⁺ concentration (y = 2.4) in the precipitates was achieved at the VV⁴⁺/V⁵⁺ solution ratio of 1.0 and pH = 3. The precipitates in solutions with pH 3 were formed only upon addition of VO²⁺ ions with the maximum rate at a V⁴⁺/V⁵⁺ ratio of 0.33. These processes were limited by second-order reactions on the surface of polyvanadates.     

Determination of thermodynamic stability of CdMoO4 by knudsen effusion vapor pressure measurement method

Thermodynamic stability of CdMoO₄ was determined by measuring the vapor pressures of Cd and MoO₃ bearing gaseous species. Th vaporization reaction could be described as CdMoO₄(s)+MoO₂(s) =Cd(g)+2/n(MoO₃)_n (n=3, 4 and 5). The vapor pressures of the cadmium (p _Cd) and trimer (p _(MoO3)3) measured in the temperature range 987≤T/K≤1111 could be expressed, respectively, as ln (p _Cd/Pa) = –32643.9/T+29.46±0.08 and ln(p _(MoO3)3/Pa) = –32289.6/T+29.28±0.08. The standard molar Gibbs free energy of formation of CdMoO₄(s), derived from the vaporization results could be expressed by the equations: °_f G _{CdMoO4 (s)} ⁰= –1002.0+0.267T±14.5 kJ mol^–1 (987≤T/K≤1033) and °_f G _{CdMoO4 (s)} ⁰ = –1101.9+0.363T±14.4 kJ mol^–1 (1044≤T/K≤1111). The standard enthalpy of formation of CdMoO₄(s) was found to be –1015.4±14.5 kJ mol^–1 .     

Phase formation in the ZrO(NO<Subscript>3</Subscript>)<Subscript>2</Subscript>-H<Subscript>3</Subscript>PO<Subscript>4</Subscript>-CsF-H<Subscript>2</Subscript>O system at low concentration of the phosphorus-containing component

The ZrO(NO₃)₂-H₃PO₄-CsF-H₂O system was studied at 20°C along the section at a molar ratio of PO₄³⁻/Zr = 0.5 (which is of the greatest interest in the context of phase formation) at ZrO₂ concentrations in the initial solutions of 2–14 wt % and molar ratios of CsF: Zr = 1−6. The following compounds were isolated for the first time: crystalline fluorophosphates CsZrF₂PO₄ · H₂O, amorphous oxofluorophosphate Cs₂Zr₃O₂F₄(PO₄)₂ · 3H₂O, and amorphous oxofluorophosphate nitrate CsZr₃O_1.25F₄(PO₄)₂(NO₃)_0.5 · 4.5H₂O. The compound Cs₃Zr₃O_1.5F₆(PO₄)₂ · 3H₂O was also isolated, which forms in a crystalline or glassy form, depending on conditions. The formation of the following new compounds was established: Cs₂Zr₃O_1.5F₅(PO₄)₂ · 2H₂O, Cs₂Zr₃F₂(PO₄)₄ · 4.5H₂O, and Zr₃O₄(PO₄)_1.33 · 6H₂O, which crystallize only in a mixture with known phases. All the compounds were studied by X-ray powder diffraction, crystal-optical, thermal, and IR spectroscopic analyses.     

Phosphates having the NaZr2(PO4)3 structure and containing titanium (or zirconium) and elements in oxidation degree 2+ (calcium or zinc)

Complex phosphates Ca_{0.5 + x} Zn _x E_{2 ? x} (PO₄)₃ (E = Ti, Zr) having NaZr₂(PO₄)₃ (NZP) structure have been prepared and characterized by X-ray diffraction, electron probe microanalysis, IR spectroscopy, and differential thermal analysis (DTA). Their phase formation has been studied by X-ray powder diffraction and DTA. The concentration and temperature fields of existence of these NZP phases have been determined: substitution solid solutions exist in the range of compositions where 0 ≤ x ≤ 0.5. The Ca_0.7Zn_0.2Ti_1.8(PO₄)₃ crystal structure has been refined by the Rietveld method (space group \(R\bar 3\) , a = 8.3636(4) Å, c = 21.9831(8) Å, V = 1331.7(1) ų, Z = 6). The framework in the NZP structure is built of octahedra, which are populated by titanium and zinc atoms, and PO₄ tetrahedra. Calcium atoms occupy extraframework positions. Extensive solid solution formation due to the accommodation of cations(2+) in the interstices within the NZP framework (M) and in the framework-forming octahedra (M′) makes it possible to design a plurality of new M_{0.5 + x} M′ _x E_{2 ? x} (PO₄)₃ phosphates with tailored structures.     

Sulfanilamide copper(II) chelates with 2-[(2-hydroxyphenyl-imino)methyl]phenolom and 1-[(2-hydroxyphenylimino)-methyl]naphthalen-2-ol

2-[(2-Hydroxyphenylimino)methyl]phenol (H²L¹) and 1-[(2-hydroxyphenylimino)methyl]naphthalen-2-ol (H²L²) reacted with copper(II) acetate hydrate and sulfanilamide (Sf¹), sulfathiazole (Sf²), sulfaethidole (Sf³), sulfadiazine (Sf⁴), and sulfadimidine (Sf⁵) in ethanol to give mixed-ligand copper chelates with the composition Cu(Sf^1–5)(L^1–2) · n H₂O (n = 1, 2). All these complexes are monomeric. Salicylaldehyde imines (H₂L¹ and H₂L²) behave as doubly deprotonated tridentate O,N,O ligands, whereas sulfanilamides (Sf^1–5) are unidentate ligands. Thermolysis of the synthesized complexes includes dehydration at 70–90°C, followed by complete thermal decomposition (290–380°C). The complexes [Cu(Sf¹)(L¹)] · 2H₂O and [Cu(Sf³)(L¹)] · H₂O at a concentration of 10⁻⁴ M inhibited growth and reproduction of 100% of human myeloid leukemia cells (HL-60). The inhibitory effect was 90 and 75%, respectively, at a concentration of 10⁻⁵ M, whereas no antitumor activity was observed at a concentration of 10⁻⁶ M.     

Catalytic dehydrogenation of propanol-2 on Na-Zr phosphates containing Cu,Co, and Ni

The dehydrogenation of propanol-2 on sodium-zirconium phosphates (NZP) with the composition Na_{1 − 2x} M _x Zr₂(PO₄)₃ (x = 0.125 and 0.25) in which Na⁺ ions were replaced by M²⁺ = Co²⁺, Ni²⁺, and Cu²⁺ ions was studied. The experimental reaction activation energy E _a decreased while transition through the T* = 310−340°C temperature; above this temperature, the electrophysical and crystallographic properties of the material changed. These changes were explained by the reversible transfer of Me²⁺ ions from position M1 to M2 in the NZP lattice. Me²⁺ centers with different alcohol adsorption forms at T < T* (one-point) and T > T* (two-point) participated in the dehydrogenation reaction. For the first form, E _a and the logarithm of the preexponential factor linearly correlated with the ionic radius of M²⁺. The activity of M-NZP catalysts altered in repeated experiments and in cases when the direction of temperature variations changed.     

Infrared spectroscopy and the structure of La0.33Zr2(Po4)3-Yb0.33Zr2(PO4)3 solid solutions

Solid solutions of double orthophosphates of zirconium and rare earth lanthanum and ytterbium (La_0.33Zr₂(PO₄)₃-Yb_0.33Zr₂(PO₄)₃) that belong to the NASICON (NZP) structural type are synthesized and studied by IR spectroscopy. The factor-group analysis of P-O vibrations in phosphates with P3 (La_0.33Zr₂(PO₄)3) and P3c (Yb_0.33Zr₂(PO₄)₃) space groups allows us to assign the intermediate representatives of this series to two different space groups by their IR spectra, which is difficult to perform based on powder X-ray diffraction results. A morphotropic transition P3 → P3 c is found to occur near the La_1/18Yb_5/18Zr₂(PO₄)₃ composition.     

Computer-assisted structure simulation, synthesis, and phase formation of molybdophosphates A1−x Zr2(PO4 3−x (MoO4)x (A is an alkali metal)

Structure simulation is performed for molybdophates of variable composition A_1?x Zr₂(PO₄)_3?x (MoO₄)_x, where A is Na (0≤x≤0.6), K (0≤x≤0.6), K (0≤x≤0.3), Rb (0≤x≤0.2), or Cs (0≤x≤0.1), using the minimization of the interatomic interaction energy; these molybdophosphates crystallize in the NaZr₂(PO₄)₃ (NZP) structure type. The results of the computer-assisted structure simulation are verified by the synthesis of the molybdophosphates and their characterization by X-ray powder diffraction and IR spectroscopy. The crystallization field of the NZP molybdophosphate shrinks as the alkali cation size increases. The key factors that govern the stability of the NZP structure in alkali zirconium molybdophosphates are determined.     

Modified Pechini synthesis of Na3Ce(PO4)2 and thermochemistry of its phase transition

Effect of the synthesis conditions of Pechini technique on crystallinity and purity of Na₃Ce(PO₄)₂ compound was investigated. Nano-sized cerium-sodium phosphate obtained when EDTA was used as an additional chelating agent for Ln³⁺. The total enthalpy change of Na₃Ce(PO₄)₂ phase transition was determined as 14.2±0.7 kJ mol⁻¹ for sample synthesized by conventional solid-solid reaction. The phase transition process was confirmed to occur at 1060°C or in temperature range 920–1060°C depending on thermal treatment of powders.     

Phase formation in the ZrO(NO3)2-H3PO4-RbF-H2O system: the PO 43? /Zr = 0.5 section

We studied phase formation in the ZrO(NO₃)₂-H₃PO₄-RbF-H₂O system along PO₄³⁻/Zr = 0.5 (mol/mol) and RbF/Zr = 1–5 (mol/mol) sections with 2–10 wt % ZrO₂ in the starting solution. We recovered amorphous rubidium oxofluorophosphatozirconate Rb₂Zr₃OF₆(PO₄)₂ · 2H₂O and the following fluorophosphatonitratozirconates: Rb₂ZrF₄(PO₄)_0.33NO₃, which forms large cubic system crystals; weakly crystallized RbZr₃OF₃(PO₄)₂(NO₃)₂ · 5H₂O; and amorphous Zr₃OF₃(PO₄)₂NO₃ · (7–8) H₂O. A shown by its IR spectrum, Rb₂ZrF₄(PO₄)_0.33NO₃ contains NO₃- and PO₄ groups that are not coordinated to zirconium, meaning that this is a triple salt ZrF₄ · Rb(PO₄)_0.33 · RbNO₃. The formula units of the RbZr₃OF₃(PO₄)₂(NO₃)₂ · 5H₂O and Zr₃OF₃(PO₄)₂NO₃ · (7–8)H₂O phases are only conventional. All compounds have been recovered for the first time.     

Phase transitions and ion transport in NASICON materials of composition Li1 + xZr2 ? xInx(PO4)3(x = 0–1)

NASICON materials of composition Li_{1 + x} Zr_{2 − x} In _x (PO₄)₃(x = 0–1) were synthesized. The phase constitution, particle size, and conductivity of these materials were studied as s function of synthesis temperature. High-temperature X-ray powder diffraction was used to study phase transitions in the materials synthesized. Low levels (x ≤ 0.1) partial substitution of indium for zirconium considerably increase the lithium ion conductivity and reduce the activation energy for conduction compared to the parent compound.