Correlation between Li+ adsorption capacity and the preparation conditions of spinel lithium manganese precursor

Spinel lithium manganese oxides can be used as Li⁺ adsorbent with topotactical extraction of lithium. In this paper, the solid state methods were introduced to prepare spinel lithium manganese precursors with Li₂CO₃ and LiOH·H₂O as different Li sources. The Li⁺ uptake was studied to clarify the correction between Li⁺ adsorption capacity and the preparation conditions of precursors, including different Li sources, Li/Mn mole ratios and heating time. The results indicated that the Li⁺-extracted materials prepared with LiOH·H₂O and MnCO₃ usually have higher Li⁺ adsorption capacity than Li₂CO₃ and MnCO₃, and an ascending trend was found in Li⁺ uptake with increasing Li/Mn mole ratio in the preparation of the precursor, but it is not proportional. The Mn₂O₃ impurities could be the primary reason for decreasing Li⁺ adsorption capacity. Furthermore, it is concluded that the Li⁺-extracted materials obtained from spinel manganese oxides synthesized with Li/Mn = 1.0 can serve as selective Li⁺ absorbents due to its high selectivity and large adsorption capacity.     

Characterization of Cu1.4Mn1.6O4/PPy composite electrodes

In this work, we have studied the multilayered polypyrrole(PPy)/oxide composite electrode on glassy carbon (GC) having the structure GC/PPy/PPy(Cu_1.4Mn_1.6O₄)/PPy using X-ray Photoelectron Spectroscopy and Mn K-edge and Cu K-edge XANES and EXAFS. The mixed oxide particles have been incorporated into the PPy matrix simultaneously to the electropolymerization of Py from a solution containing 0.1 M Py + 0.15 M KCl + Cu_1.4Mn_1.6O₄. The XPS data have shown that, prior to the incorporation of the oxide into the PPy matrix, it contains Cu⁺, Cu²⁺, Mn³⁺ and Mn⁴⁺. The XPS, XANES and EXAFS results have shown that when the oxide is incorporated into the PPy matrix, the Cu⁺ present in the original oxide suffers dismutation to give Cu²⁺ and metallic Cu. The metallic Cu is segregated out of the spinel structure. The Mn K-edge XANES and EXAFS data show that, after the incorporation into the PPy matrix, Mn is present as Mn³⁺ and Mn⁴⁺ occupying octahedral sites in a spinel-related structure while the Cu K-edge XANES and EXAFS data indicate that copper occupies tetrahedral sites predominantly in that structure but having a large degree of disorder in the second and higher coordination shells.     

Hydrothermal phase formation of orthorhombic LiMnO2 and its derivatives as lithium intercalation compounds

Different from a conventional solid state reaction, a hydrothermal reaction mechanism is very difficult to illuminate and sometimes it remains undisclosed. Making an attempt to understand the hydrothermal phase formation process of o-LiMnO₂ obtained between the reaction of spinel type Mn₃O₄ precursor and LiOH aqueous solution, the possible reaction route was postulated and experimentally testified. Firstly, the selective dissolution of Mn²⁺ from the tetrahedral site of [Mn^II]^tet_4a[Mn^III₂]^oct_8dO₄, which is considered as to be an ionic exchange reaction with Li⁺, and an additional Li⁺ intercalation into the host structure of precursor would give rise to the formation of meta-stable Li₂Mn₂O₄ ([Li^I]^tet_4a[Li^I]^oct_8c[Mn^III₂]^oct_8dO₄). Secondly, the phase would be simultaneously transformed to thermodynamically stable o-LiMnO₂ phase under hydrothermal state during hydrothermal reaction. Through the above reaction process, the solid solution range of o-LiCo_xMn_1−xO₂ was as large as x ≤ 0.14, and that of o-LiFe_xMn_1−xO₂ was x ≤ 0.05. Co doped o-LiMnO₂ has higher capacity and good cyclability upon cycling, being substantially more stable to cycle than the unsubstituted and Fe doped materials.     

Conductivities of electrolytes based on PEI-b-PEO-b-PEI triblock copolymers with lithium and copper TFSI salts

Tri block-copolymer poly(iminoethylene)-b-poly(oxyethylene)-b-poly(iminoethylene) with a poly(oxyethylene) central block (PEI-b-PEO-b-PEI) were used as a “dual” matrix for polymer electrolytes having selectivity for hard cations (Li⁺/PEO) in one phase and for soft cations (Cu²⁺/PEI) in the other. Conductivity measurements were recorded for 20:1, 12:1 and 8:1 coordinating atom (O or/and N) to cation (Li⁺, Cu²⁺) ratios, for each of the three complexes studied: PEI-b-PEO-LiTFSI-b-PEI, PEI-Cu(TFSI)₂-b-PEO-b-PEI-Cu(TFSI)₂ and PEI-Cu(TFSI)₂-b-PEO-LiTFSI-b-PEI-Cu(TFSI)₂. For either low (20 °C) or high temperature (80 °C) the highest conductivity was given by the polymer electrolyte based on Cu(TFSI)₂ with N/Cu²⁺ = 20:1 (10^− 6, respectively 2 × 10^− 4 S cm^− 1). In the present paper, the conductivity evolution is discussed in relation with the polymer structure, the type and the concentration of the salt and the thermal behavior of our systems.     

White-light generation through Ce3+/Mn2+-codoped and Eu2+-doped Ba1.2Ca0.8SiO4 T-phase phosphors

Hexagonal Ba_1.20Ca_0.8?2x?ySiO₄:xCe³⁺,xLi⁺,yMn²⁺ phosphors exhibit two emission bands peaking near 400 and 600 nm from the allowed f–d transition of Ce³⁺ ions and the forbidden ⁴T₁–⁶A₁ transition of Mn²⁺ ions, respectively. The strong interaction between Ce³⁺/Mn²⁺ ions is investigated in terms of energy transfer, crystal field effect, and microstructure by varying their concentrations. They show a higher quenching temperature of 250 °C than that of a commercially used (Ba,Sr)₂SiO₄:Eu²⁺ phosphor (150 °C). Finally, mixtures of these phosphors with green-emissive Ba_1.20Ca_0.70SiO₄:0.10Eu²⁺ are tested and yielded correlated color temperatures from 3500 to 7000 K, and color rendering indices up to 95%.     

7Li and 51V NMR study on Li+ ionic diffusion in lithium intercalated LixV2O5

Li_xV₂O₅ (0.4 < x < 1.4) prepared by solid-state reaction were studied by ⁷Li and ⁵¹V NMR spectroscopy. ⁷Li NMR spectra showed a narrowing of the line width in relation to Li⁺ionic diffusion. Analysis of Li_xV₂O₅ using a Debye-type relaxation model showed a low activation energy ∼0.07 eV in the sample of x = 0.4 below room temperature, and revealed a Li⁺ionic diffusion with larger activation energy ∼0.5 eV above 450 K in lithium-rich samples. The latter is ascribed to the existence of a multi-phase system comprising stable ɛ- and γ-phases, resulting from complicated phase transitions at high temperature. These shapes and shifts enable the classification of the β-, ɛ-, δ-, and γ-phases. The ionic diffusion of Li⁺ ions is discussed in relation to the complicated phase transitions.     

Investigation of the structural and dynamical properties of the (0 0 1) surface of LiCu2O2

We report on studies of the structure and dynamics of the (0 0 1) surface of single crystal LiCu₂O₂, investigated by He beam scattering at room temperature, and with lattice-dynamical models. The best fit surface corrugation to measured diffraction patterns shows that the surface termination is exclusively a Li¹⁺Cu²⁺O^2? plane. Lattice dynamics fits to inelastic He scattering spectra reveal the presence of two low-lying surface phonon modes, identified with the motion of Cu²⁺, Li¹⁺ surface ions normal to the surface.     

Effect of composition change of metals in transition metal sites on electrochemical behavior of layered Li[Co1 −2x(Li1 / 3Mn2 / 3)x(Ni1 / 2Mn1 / 2)x]O2 solid solutions

Five compositions of Li[Co_1 −2x(Li_1 / 3Mn_2 / 3)_x(Ni_1 / 2Mn_1 / 2)_x]O₂ solid solutions ( x = 0.1, 0.2, 0.3, 0.4, and 0.5) were synthesized using a sol–gel method with three end members of LiCoO₂, Li₂MnO₃(Li[Li_1 / 3Mn_2 / 3]O₂), and Li[Ni_0.5Mn_0.5]O₂. The compositions of metals in transition metal sites were changed to see the effect of them on electrochemical behavior of the solid solutions. All the samples were nano-sized semi-spherical shaped particles with a layered structure. The reduction of cobalt content (the increase of other metals) in the sites increases the lattice parameters, a and c, resulting in the shift of Raman and XRD peak positions. The discharge capacity fading turned serious at higher Co contents, but it was significantly diminished with the decrease of Co content. At lower Co contents, the capacity increased with cycle numbers. The most stable voltage profile was obtained from the composition of Li[Li_1 / 15Co_3 / 5Ni_1 / 10Mn_7 / 30]O₂ (x = 0.2).     

A single-crystal study of the electrochemically Li-ion intercalated spinel-type Li4Ti5O12

Single crystals of Li_4 + xTi₅O₁₂ were prepared by means of electrochemical Li-ion intercalation technique using parent Li₄Ti₅O₁₂ single crystals. The obtained Li_4 + xTi₅O₁₂ (x = 1.35) crystallizes in the cubic spinel-related type structure, space group Fd3?m, and lattice parameters of a = 8.346(2) Å and V = 581.3(5) Å³ and Z = 8. The Li-ion intercalated sites were successfully determined to be both the 8a and 16c sites by using the difference Fourier synthesis map. The structure was determined by single-crystal X-ray structure analysis and refined to the conventional value of R = 3.7% for 132 independent observed reflections. The chemical composition has been determined to be Li_5.35Ti₅O₁₂ from the result of site-population refinements. In addition, theoretical electron density distributions and total energy were calculated for three postulated compounds of “Li_4.5Ti_4.5O₁₂” and “Li_4.5 + xTi_4.5O₁₂” with x = 1.5 and 3.0.     

Luminescent properties of Eu3+ and Sm3+ activated M2SiO4 (M=Ba,Sr and Ca) red-emitting phosphors for WLEDs

Eu³⁺ and Sm³⁺ activated M₂SiO₄ (M=Ba, Sr and Ca) red-emitting phosphors were synthesized by a solid state reaction. The results of XRD and SEM measurements show that the samples are single phase and have irregular shape. The excitation and emission spectra indicate that these phosphors were effectively excited by ultraviolet (395 nm) and blue (466 nm) light and exhibited red performance. The charge compensator R⁺ (R⁺=Li⁺, Na⁺ and K⁺) injecting into the host efficiently enhanced the luminescence intensity of the M₂SiO₄: Eu³⁺ and M₂SiO₄: Sm³⁺ phosphors. The emission intensity of M₂SiO₄: Eu³⁺ and Sm³⁺ doping Li⁺ were higher than that of Na⁺ or K⁺.     

Preparation of carbon nanoparticles from electrolysis of molten carbonates and use as anode materials in lithium-ion batteries

The electrochemical reduction of molten Li–Na–K carbonates at 450 °C provides “quasi-spherical” carbon nanoparticles with size comprised between 40 and 80 nm (deduced from AFM measurements). XRD analyses performed after washing and heat-treatment at various temperatures have revealed the presence of graphitised and amorphous phases. The d₀₀₂ values were close to the ideal one obtained for pure graphite. Raman spectroscopy has pointed out surface disordering which increases with increasing temperature of the heat-treatment. The presence of Na and Li on the surface of the carbon powder has been evidenced by SIMS. The maximum Na and Li contents were observed for carbon samples heat-treated at 400 °C. Their electrochemical performances vs. the insertion/deinsertion of lithium cations were studied in 1 M LiPF₆–EC : DEC : DMC (2 : 1 : 2). The first charge–discharge cycle is characterised by a high irreversible capacity as in the case of hard-disordered carbon materials. However, the potential profile in galvanostatic mode is intermediate between that usually observed for graphite and amorphous carbon: rather continuous charge–discharge curves sloping between 1.5 and 0.3 V vs. Li / Li⁺, and successive phase transformations between 0.3 and 0.02 V vs. Li / Li⁺. The best electrochemical performances were obtained with carbon powders heat-treated at 400 °C which exhibits a reversible capacity value of 1080 mAh g^− 1 (composition of Li_2.9C₆). This sample has also both the lowest surface disordering (deduced from Raman spectroscopy), and the highest Na and Li surface contents (deduced from SIMS).     

The studies on structural and thermal properties of delithiated LixNi1/3Co1/3Mn1/3O2 (0 < x ≤ 1) as a cathode material in lithium ion batteries

The structural and thermal properties of the delithiated Li_xNi_1/3Co_1/3Mn_1/3O₂ (0 < x ≤ 1) material have been investigated by using diffraction and thermoanalytical techniques such as XRD and TG-DSC methods. XRD result shows that the delithiated materials maintain the O3-type structure with defined stoichiometric number at the range of 0.24 < x ≤ 1, exhibiting good crystal structural stability. The cobalt and nickel ions in the delithiated materials change their valence state (i.e. Co³⁺ to Co⁴⁺ and Ni³⁺ to Ni⁴⁺) when x < 0.49; the irreversible changes of the transformation may affect the first cycle of charge–discharge efficiency of the materials. A comparison of the results of TG-DSC with TPD-MS shows that the irreversible change of oxygen species during the delithiation process of Li_xNi_1/3Co_1/3Mn_1/3O₂ have great influence on the structural and thermal stability and reversibility of the materials.     

Photo-luminescence properties of Cu and Ag doped Li2B4O7 single crystals at low temperatures

UV excited photo luminescence from Li₂B₄O₇:Cu and Li₂B₄O₇:Cu, Ag single crystals has been investigated in the temperature range from 77 K to 300 K. An excitation band having a doublet structure at 240 nm and 262 nm was observed for the emission at 370 nm that corresponds to ¹A_1g→¹E_g and ¹A_1g→¹T_2g crystal field components of the 3d¹⁰→3d⁹4s¹ transition of Cu⁺. The relative intensity of these components and their temperature dependence provide a measure of the off-center displacement of the Cu⁺ ground state in the crystal lattice site. The co-doped Ag plays a role of a sensitizer when doped with Cu and increases the overall emission as the emission between Ag states lies in the excitation region of Cu states. The 370 nm emission in both the crystals slightly decreases with temperature; however a sudden increase in the intensity around 264 K was observed.     

Influence of simultaneous doping of Sb and Pb on phase formation,superconducting and microstructural characteristics of HgBa2Ca2Cu3O8+δ

We report systematic studies of structural, microstructural and transport properties of (Hg_0.80Sb_0.2−xPb_x)Ba₂Ca₂Cu₃O_8+δ (where x = 0.0, 0.05, 0.1, 0.15, 0.2) compounds. Bulk polycrystalline samples have been prepared by two-step solid-state reaction route at ambient pressure. It has been observed that simultaneous substitution of Sb and Pb at Hg site in oxygen deficient HgO_δ layer of HgBa₂Ca₂Cu₃O_8+δ cuprate high-T_c superconductor leads to the formation of Hg-1223 as the dominant phase. Microstructural investigations of the as grown samples employing scanning electron microscopy reveal single crystal like large grains embodying spiral like features. Superconducting properties particularly transport current density (J_ct) have been found to be sensitive to these microstructural features. As for example (Hg_0.80Sb_0.05Pb_0.15)Ba₂Ca₂Cu₃O_8+δ compound which exhibits single crystal like large grains (∼50 μm) and appears to result through spiral growth mechanism, shows highest J_ct (∼1.85 × 10³ A/cm²) at 77 K. A possible mechanism for the generation of spiral like features and correlation between microstructural features and superconducting properties have been put forward.     

7Li NMR study on Li+ ionic diffusion and phase transition in LixCoO2

The temperature dependence of the spin-lattice relaxation time, T₁ and the line width of the ⁷Li nucleus were measured in delithiated Li_xCoO₂ (x = 0.6, 0.8, 1.0). Two different relaxation behaviors were observed in the temperature dependence of T₁^− 1 in a x = 0.8 sample. These would have arisen from inequivalent Li sites in two coexisting phases; an original hexagonal (HEX-I) and a modified hexagonal (HEX-II) phase in the x = 0.8 sample. We analyzed using a phenomenological non Debye-type relaxation model. Motional narrowing in the line width was observed in each sample, the result revealing that Li⁺ ions begin to move at low temperature in samples with less Li content. It was found that the activation energy associating with Li⁺ ion hopping in the HEX-II phase is smaller than that in the HEX-I phase. These results show that the HEX-II phase produced in the Li deintercalation process would be suitable for Li⁺ ionic diffusion in multi-phase Li_xCoO₂, and it is expected that this would enable fast ionic diffusion. Li⁺ ionic diffusion related to phase transition is discussed from ⁷Li NMR results.     

Structural and electrochemical study of Cr-substituted layered manganese oxide cathode materials

A lithiated layered Mn–Cr compound, Li[Cr_0.29Li_0.24Mn_0.47]O₂ was synthesized by a solution method with subsequent quenching. The crystal structure was investigated by X-ray diffraction (Rietveld refinement) and Electron diffraction showing co-existence of rhombohedral and monoclinic structures. According to the co-indexed electron diffraction patterns and HRTEM images, Li[Cr_0.29Li_0.24Mn_0.47]O₂ electrode was composed of nano-scale domains indexed in monoclinic and hexagonal structures, simultaneously. The nano-composite cathode successfully prevents spinel-like structural transformation during cycling and delivered a good reversible capacity of about 195 mAh/g between 2.4 and 4.7 V.     

Formation and its mechanism of copper metal layers at surface by annealing in reduced atmosphere in CuO–Li2O–Nb2O5–SiO2 glass

A trace amount (0.5 mol%) of CuO-doped 40Li₂O–32Nb₂O₅–28SiO₂ glass (mol%) exhibits the formation of copper metal layers at the glass surface by annealing at temperatures (530 °C) below the glass transition temperature (544 °C) in the reduced atmosphere of 7% H₂–93%Ar. The coordination state of copper ions is examined from optical absorption and Fourier transform infrared (FT-IR) spectrum measurements, indicating the formation of Si–OH and Si–H bonds due to the diffusion of hydrogen into the inside of the glass and the reduction of Cu⁺ and Cu²⁺ ions. The mechanism of the formation of copper metals at the surface is proposed, in which the key points are the reduction of Cu²⁺ to Cu⁺ ions due to the hydrogen and the migration of Cu⁺ ions in the interior of the glass to the surface. The first finding on copper metal layers at the glass surface might have a potential for practical applications such as electrodes in glass.     

Antiferromagnetic phase transition in garnet-type AgCa2Mn2V3O12 and NaPb2Mn2V3O12

Ferrimagnetism has been extensively studied in garnets, whereas it is rare to find the antiferromagnet. Present work will demonstrate antiferromagnetism in the two Mn–V-garnets. Antiferromagnetic phase transition in AgCa₂Mn₂V₃O₁₂ and NaPb₂Mn₂V₃O₁₂ has been found, where the magnetic Mn²⁺ ions locate only on octahedral A site. The heat capacity shows sharp peak due to antiferromagnetic order with the Néel temperature T_N=23.8 K for AgCa₂Mn₂V₃O₁₂ and T_N=14.2 K for NaPb₂Mn₂V₃O₁₂. The magnetic entropy change over a temperature range 0–50 K is 13.9 J K^?1 mol-Mn²⁺-ions^?1 for AgCa₂Mn₂V₃O₁₂ and 13.6 J K^?1 mol-Mn²⁺-ions^?1 for NaPb₂Mn₂V₃O₁₂, which are in good agreement with calculated value of Mn²⁺ ion with spin S=5/2. The magnetic susceptibility shows the Curie–Weiss behavior over the range 29–350 K. The effective magnetic moment μ_eff and the Weiss constant θ are μ_eff=6.20 μ_B Mn²⁺-ion^?1 and θ=?34.1 K (antiferromagnetic sign) for AgCa₂Mn₂V₃O₁₂ and μ_eff=6.02 μ_B Mn²⁺-ion^?1 and θ=?20.8 K for NaPb₂Mn₂V₃O₁₂.     

Synthesis and crystallographic studies of garnet-related lithium-ion conductors Li6CaLa2Ta2O12 and Li6BaLa2Ta2O12

High-purity specimens of Li₆CaLa₂Ta₂O₁₂ and Li₆BaLa₂Ta₂O₁₂ have been successfully synthesized by solid-state reactions. The analytical chemical compositions of these samples were in good agreement with the nominal compositions of Li₆CaLa₂Ta₂O₁₂ and Li₆BaLa₂Ta₂O₁₂. The Rietveld refinements verified that these compounds have the garnet-type framework structure with the lattice constants of a = 12.725(2) Å for Li₆CaLa₂Ta₂O₁₂ and a = 13.001(4) Å for Li₆BaLa₂Ta₂O₁₂. All of the diffraction peaks of X-ray powder diffraction patterns were well indexed on the basis of cubic symmetry with space group Ia-3d. To make a search for Li sites, the electron density distributions were precisely examined by using the maximum entropy method. Li⁺ ions occupy partially two types of crystallographic site in these compounds: (i) tetrahedral 24d sites, and (ii) distorted octahedral 96h sites, the latter of which are the vacant sites of the ideal garnet-type structure. The present Li₆CaLa₂Ta₂O₁₂ and Li₆BaLa₂Ta₂O₁₂ samples exhibit the conductivity σ = 2.2 × 10^? 6 S cm^? 1 at 27 °C (E_a = 0.50 eV) and σ = 1.3 × 10^? 5 S cm^? 1 at 25 °C (E_a = 0.44 eV), respectively.