Zirconia-based planar NO2 sensor using ultrathin NiO or laminated NiO–Au sensing electrode

The nanostructured thin NiO films with the thicknesses of 30–180 nm were examined as a sensing electrode (SE) for the planar mixed-potential-type yttria-stabilized zirconia (YSZ)-based NO₂ sensor. The sensing characteristics were examined in the temperature range of 600–800 °C under the wet condition (5 vol.% water vapor). Among the NiO-SEs tested, the 60 nm-thick NiO-SE sintered at 1,000 °C was found to give the highest NO₂ sensitivity in the NO₂ concentration range of 50–400 ppm accompanying with fast response/recovery at the operating temperatures of 600–700 °C. The high NO₂ sensitivity was attributed to the high catalytic activity for both electrochemical reactions of O₂ and NO₂ at the interface of NiO-SE/YSZ. The ultrathin gold layer with the thickness of about 60 nm was additionally formed on the 60 nm-thick NiO-SE to fabricate the laminated-type (60 nm NiO/60 nm Au)-SE. It was demonstrated that the use of this laminated (NiO–Au)-SE improved both the sensitivity and the selectivity to NO₂.     

NO2 sensing properties of YSZ-based sensor using NiO and Cr-doped NiO sensing electrodes at high temperature

Nickel oxide and chromium-doped nickel oxide (Ni_0.95Cr_0.03O_1−δ ) were prepared by thermal decomposition of nitrates. The obtained NiO and Ni_0.95Cr_0.03O_1−δ samples were utilized as sensing electrodes (SEs) in yttria-stabilized zirconia (YSZ)-based sensors for detection of NO₂ at 800 °C under wet condition (5 vol.% H₂O). While the mixed-potential-type planar sensor attached with NiO-SE gave rather large NO₂ sensitivity, the sensor attached with Ni_0.95Cr_0.03O_1−δ -SE exhibited fast recovery rate with an acceptable sensitivity. The Δemf (electromotive force) of the sensors varied linearly with NO₂ concentration in the examined range of 50–400 ppm on a logarithmic scale. Based on the results of measurements for polarization, complex impedance and gas phase catalysis, the fast recovery was attributable to the high rate for the anodic reaction of O₂ at the Ni_0.95Cr_0.03O_1−δ /YSZ interface, and the lower NO₂ sensitivity was caused by both the high rate for the anodic reaction of O₂ and the high degree for the gas phase conversion of NO₂ to NO.     

Dependence of NO2 sensitivity on thickness of oxide-sensing electrodes for mixed-potential-type sensor using stabilized zirconia

The effect of thickness of oxide-sensing electrode (SE) on NO₂ sensitivity of the planar sensor based on yttria-stabilized zirconia (YSZ) was examined at high temperatures. The sensitivity of the sensor increased with decreasing thickness of SE, and the highest sensitivity was obtained by using the thinnest layer of Cr₂O₃–SE (2.7 μm) at 700 °C. In the case of NiO–SE, the highest sensitivity was observed for the sensor using the 4-μm-thick SE even at a high temperature of 850 °C. Based on the results of the measurements for the complex impedances, the polarization curves, and the gas-phase NO₂ decomposition catalysis, it was confirmed that the catalytic activity to the gas-phase NO₂ decomposition on the oxide–SE matrix played an important role in determining the NO₂ sensitivity of the present sensors.     

NO<Subscript>2</Subscript>-sensing properties of La<Subscript>0.65</Subscript>Sr<Subscript>0.35</Subscript>MnO<Subscript>3</Subscript> synthesized by self-propagating combustion

Ultrafine-structure La_0.65Sr_0.35MnO₃ (LSM) powders synthesized by self-propagating combustion method have been used to fabricate sensing electrodes (SEs) for NO₂ mixed-potential sensors based on yttria-stabilized zirconia (YSZ). This type of sensor was found to provide better NO₂ sensitivity at 500 °C than sensors with LSM powders synthesized by traditional solid-state methods. The response values of the sensor have good linear relationship (sensitivity 36.6 mV/decade and linear fit 0.99) with the logarithm of NO₂ concentration varying from 30 to 500 ppm. The influence of sintering temperature (1000, 1100, 1200, and 1300 °C) on sensor response was also examined and was found to have a significant effect on the morphology of LSM-SEs. Moreover, in the presence of NO, CO₂, CO, and NO₂, the sensor exhibited good NO₂ selectivity.     

Mixed-potential-type NOx sensor based on YSZ and zinc oxide sensing electrode

Electrochemical sensors using tubular yttria-stabilized zirconia (YSZ) and oxide sensing electrode (SE) were fabricated and examined for NO_x detection at high temperatures. The mixed-potential-type NO_x sensor using ZnO-SE gave the highest sensitivity to NO_x among other single-type oxides tested as SEs in the temperature range of 600–700 °C. The response of the ZnO-attached device was a linear for the logarithm of NO₂ (NO) concentrations from 40 to 450 ppm. The sensing mechanism of the sensor was discussed on the basis of the gas adsorption-desorption behavior, the catalytic activity data, and electrochemical behavior for oxides examined.     

Dependence of NO<Subscript>2</Subscript> sensitivity on thickness of oxide-sensing electrodes for mixed-potential-type sensor using stabilized zirconia

The effect of thickness of oxide-sensing electrode (SE) on NO₂ sensitivity of the planar sensor based on yttria-stabilized zirconia (YSZ) was examined at high temperatures. The sensitivity of the sensor increased with decreasing thickness of SE, and the highest sensitivity was obtained by using the thinnest layer of Cr₂O₃–SE (2.7 μm) at 700 °C. In the case of NiO–SE, the highest sensitivity was observed for the sensor using the 4 μm-thick SE even at high temperature of 850 °C. Based on the results of the measurements for the complex impedances, the polarization curves, and the gas-phase NO₂ decomposition catalysis, it was confirmed that the catalytic activity to the gas-phase NO₂ decomposition on the oxide–SE matrix played an important role in determining the NO₂ sensitivity of the present sensors. This artice was accidentally published twice. This is the second publication, please cite only the authoritative first one which is available at . An additional erratum is available at . An erratum to this article can be found at     

Fabrication and electrochemical performance of La<Subscript>0.5</Subscript>Sr<Subscript>0.5</Subscript>CoO<Subscript>3</Subscript> impregnated porous YSZ cathode

La_0.5Sr_0.5CoO₃-yttria-stabilized zirconia (LSCO-YSZ) composite cathode for solid oxide fuel cell (SOFC) has been fabricated by wet impregnation method. Nitrate precursors of La, Sr, and Co have been impregnated into the pre-sintered porous YSZ matrix, which is converted into LSCO phase after calcination at 850 °C in the presence of glycine as confirmed from X-ray diffraction. LSCO of 5, 7, and 10 wt% impregnated porous YSZ have been electrochemically characterized using 2-probe AC conductivity method. Maximum ionic conductivity of 0.27 S/cm at 800 °C and activation energy of 0.15 eV between 600 and 800 °C have been observed for 10 wt% LSCO-YSZ cathode. Area-specific resistance of 1.01 Ω cm² at 800 °C is estimated for the electrolyte-supported half-cell (10 wt% LSCO-YSZ/YSZ). After testing the LSCO-YSZ cathode matrix, the electrolyte-supported full cell (10 wt% LSCO-YSZ/YSZ/NiO-YSZ) has been tested and produced maximum power density 51.12 mW/cm² (109.38 mA/cm²) at 800 °C. The electrolyte-supported full cell exhibited 6 Ω cm² electrode polarization at 800 °C in H₂, which is in higher side leading to low performance. LSCO-YSZ/YSZ/NiO-YSZ SOFC found to give stable performance up to 2 h and scanning electron microscopy analysis has been carried out before and after cell testing to assess the morphological changes.     

Structural and electrical properties of ZnO-doped 8 mol% yttria-stabilized zirconia

8 mol% Yttria-stabilized zirconia (8YSZ) powder was prepared by coprecipitation. ZnO (0.5, 1.0, 2.0, 5.0, 10.0 wt.%) was added to the YSZ powder through a mechanical mixing method. The densification , microstructure and electrical properties of the YSZ ceramics sintered at 1300 °C for 2 h, were investigated. It was found that the small addition of ZnO was effective in reducing the sintering temperature and promoting the densification rate of the ceramics. The 5.0 wt.% ZnO-doped YSZ has ∼ 96% relative density, as compared to ∼ 89% relative density for the undoped sample. The total conductivity of 8YSZ was evidently increased by doping small amount of ZnO. For the 0.5 wt.% doped sample, the total conductivity of 2.89 × 10^− 2 Ω^− 1 cm^− 1 and an increase of 120% in conductivity were observed at 800 °C, as compared to that of the undoped one. We also found that the grain boundary (GB) conductivity could be improved by small addition of ZnO. At intermediate temperature (∼ 300 °C), the maximum enhancement of GB conductivity was observed with 5.0 wt% ZnO dopant. Finally, the volume percentage of GB in the ceramics was estimated by the brick layer model. The possible mechanism related to the improved GB conduction of the YSZ due to the ZnO additions was discussed.     

Synthesis of nanostructured lean-NO x catalysts by direct laser deposition of monometallic Pt-, Rh- and bimetallic PtRh-nanoparticles on SiO2 support

Monometallic Pt and Rh and bimetallic PtRh catalysts with a highly dispersed noble metal weight loading of ca. 1 wt% were produced via the direct deposition of nanoparticles on different SiO₂ supports by means of pulsed ultra-violet (248 nm) excimer laser ablation of Pt, Rh bulk metal and PtRh alloy targets. Backscattered electron microscopy (BSE), energy dispersive X-ray spectroscopy (EDX), and transmission electron microscopy (TEM) were employed to characterize the deposited nanoparticles, which were found to exhibit narrow size distribution centred around 2.5 nm. The catalytic activities for lean NO _x reduction of the monometallic and bimetallic catalyst samples were investigated in a flow reactor setup in the temperature range 100–400°C using a test gas mixture representative of oxygen rich diesel engine exhaust gas. For comparison a Rh/SiO₂ reference catalyst prepared by a conventional impregnation method was also tested. Further experiments were performed in which PtRh nanoparticles were deposited on a Rh/SiO₂ reference catalyst sample to study the possibility for controlled modification of its activity. The catalytic activity measurements revealed that among the samples solely prepared by laser deposition the PtRh–SiO₂ nanoparticle catalyst showed the highest activity for NO _x reduction at low temperatures 100–300°C. In addition, it could be demonstrated that the initially low NO _x reduction activity and the N₂ selectivity of the Rh/SiO₂ reference catalyst sample for temperatures below 250°C can be enhanced by post laser deposition of PtRh nanoparticles.     

Composite (La,Sr)MnO3–YSZ cathode for SOFC

(La, Sr)MnO₃ (LSM)–Y doped ZrO₂ (YSZ) composite was prepared using YSZ colloidal suspension (initial YSZ particle size ∼100 nm), YSZ and LSM polymer precursors on dense substrates at 800 °C annealing temperature. The results of a symmetrical LSM–YSZ composite cell test showed the area specific resistance for overpotential of 0.14 Ω cm² at 800 °C, which indicated that the LSM–YSZ composite could be a potential candidate for cathode in SOFCs. The performance of the cell with the LSM–YSZ composite cathode and Ni-YSZ anode was investigated and the power density of about 0.26 W cm^− 2 was obtained at 850 °C using hydrogen fuel.     

Polypyrrole–NiO hybrid nanocomposite films: highly selective,sensitive, and reproducible NO2 sensors

Polypyrrole–nickel oxide (PPy–NiO) hybrid nanocomposite thin-film sensor was prepared by spin-coating method on glass substrate. The PPy–NiO hybrid nanocomposite thin film sensors were used to study room temperature gas-sensing properties for oxidizing (NO₂, Cl₂) as well as reducing (NO₂, H₂S, C₂H₅OH, NH₃, and Cl₂) gases. It was revealed that PPy–NiO (50 %) hybrid nanocomposite thin-film sensor could detect NO₂ at low concentration (100 ppm) with very high selectivity (47 % compared with Cl₂) and high sensitivity (47 %), with better stability (90 %) and reproducibility. The response and recovery times were changed significantly with NO₂ concentration.     

In situ controlled promotion of catalyst surfaces via solid electrolytes: Ethylene oxidation on Rh and propylene oxidation on Pt

The kinetics of C₂H₄ oxidation on Rh and C₃H₆ oxidation on Pt were investigated on polycrystalline metal films interfaced with ZrO₂(8mol%Y₂O₃) solid electrolyte in galvanic cells of the type:

CeO<Subscript>2</Subscript> and Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> modified Ni-YSZ anode for solid oxide fuel cell

Ni sintering at high temperature (～ 800 °C) operation drastically degrades the performance of Ni-yttria-stabilized zirconia (YSZ) anode in solid oxide fuel cell (SOFC). Mixed ionic and electronic conductive oxides such as CeO₂ and Nb₂O₅ enhance the dispersion of Ni, CeO₂ enhances the redox behavior and promotes charge transfer reactions, and Nb₂O₅ increases the triple phase boundary. In the present work, anode-supported SOFC is fabricated and tested in H₂ fuel at 800 °C. YSZ and lanthanum strontium manganite (LSM)-YSZ are used as the electrolyte and composite cathode with NiO-YSZ, CeO₂-NiO-YSZ, and Nb₂O₅-NiO-YSZ as an anode. The peak power density obtained for the cell with 10% CeO₂–30% NiO-YSZ anode at the 5 and 25 h of operation is 330 and 290 mW cm^?2 which is higher than that for 40% NiO-YSZ anode (275 mW cm^?2 at 5 h). The peak power density obtained for the cell with 10% Nb₂O₅–30% NiO-YSZ anode at the 5 and 25 h of operation is 301 and 285 mW cm^?2 which is higher than that for 40% NiO-YSZ anode (275 mW cm^?2 at 5 h). Physical characterization has been carried to study morphology, elemental analysis, particle size, and phase formation of the fabricated anode before and after cell operation to correlate the cell performance.     

Electrode materials for potentiometric hydrogen sensors

Due to their relatively high sensitivity, improved long-term stability, possibilities for miniaturization and low cost products, mixed potential solid electrolyte sensors can be competitive for the in situ measurement of hydrogen trace concentrations in oxygen containing gases. Their response behavior in non-equilibrated oxygen containing gas mixtures is mainly determined by the catalytic activity of the measuring electrode and depends strongly on preparation and measuring conditions. In this work the sensitivity of electrodes made of composites (Au/MeO) has been investigated in hydrogen containing gases in the concentration range φ(H₂) = 0…800 vol.-ppm using a two-chamber setup with Pt-air reference. Electrodes made of Au/Nb₂O₅ composites show the highest sensitivities of up to 20 mV/vol.-ppm at φ(H₂) = 10 vol.-ppm and the lowest catalytic activity for hydrogen oxidation. Selected composite materials were tested additionally in self-heated solid electrolyte sensors with both electrodes exposed to the same atmosphere (gas-symmetrical sensor).     

Temperature dependence of NO2 sensitivity of YSZ-based mixed potential type sensor attached with NiO sensing electrode

A mixed potential type yttria-stabilized zirconia-based sensor using NiO sensing electrode and Pt reference electrode was fabricated, and its NO₂ sensing characteristics were examined at various operating temperatures in the range of 700–950 °C. It was observed that the sensitivity to NO₂ strongly depends on the operating temperature of the sensor; the sensitivity decreases with increasing operating temperature, while the response/recovery rates increase. To rationalize this temperature dependence of NO₂ response, polarization curves and complex impedances of the sensor were measured in the base gas and in the sample gas (400 ppm NO₂?+?base gas) at various operating temperatures. It turned out that the operating temperature had a strong influence on the rate of anodic reaction of oxygen; the increased rate of anodic reaction leads to lower NO₂ sensitivity and quicker response/recovery at higher operating temperature.     

Facile synthesis of nanostructured CuO for low temperature NO2 sensing

Detection of environmental pollutant and health hazardous, nitrogen dioxide (NO₂) is reported using nanostructured CuO particulates (NPs). Powder X-ray diffraction and field emission scanning electron microscopy were used to probe crystalline phase and morphological details, respectively. Small crystallites of ∼10–12 nm and a strain of 4% were found in the leafy structure of CuO. Raman studies further supported the presence of nanosized CuO phase. This is the first instance of utilizing CuO NPs to detect 5 ppm of NO₂ even at a low operating temperature of 50 °C. The highest sensitivity for NO₂ was observed at 150 °C, for the first time, in CuO NPs. A low activation energy of 0.18 eV was found for sensing process. The CuO NPs sensor responded to NO₂ within a few seconds and recovered totally under a minute. The kinetics of the NO₂ gas adsorption on the CuO film surface was described following the Elovich model.     

(La0.75Sr0.25)(Cr0.5Mn0.5)O3/YSZ composite anodes for methane oxidation reaction in solid oxide fuel cells

The synthesis and performance of (La_0.75Sr_0.25)(Cr_0.5Mn_0.5)O₃/Y₂O₃–ZrO₂ (LSCM/YSZ) composites are investigated as alternative anodes for the direct utilization of methane (i.e., natural gas) in solid oxide fuel cells. Addition of YSZ phase greatly improves the adhesion and reduces the electrode polarization resistance of the LSCM/YSZ composite anodes. LSCM/YSZ composite anodes show reasonably good performance for the methane oxidation reaction in wet CH₄ and the best electrode performance was achieved for the composite with LSCM contents of 50–60 wt.% with polarization resistances of 2–3 Ω cm² in 97% CH₄/3% H₂O at 850 °C. The electrode impedance for the methane oxidation in wet CH₄ on the LSCM/YSZ composite anodes was characterized by three separable arcs and the electrode behavior could be explained based on the ALS model for the reaction on the MIEC electrode. The results indicate that electrocatalytic activity of the LSCM/YSZ composite anodes for the methane oxidation is likely limited by the oxygen vacancy diffusion in the substituted lanthanum chromite-based materials.     

Enhanced NO2 gas sensing properties of WO3 nanorods encapsulated with ZnO

The influence of the encapsulation of WO₃ nanorods with ZnO on the NO₂ gas sensing properties was examined. WO₃-core/ZnO-shell nanorods were fabricated by a two-step process comprising the catalyst-free thermal evaporation of a mixture of WO₃ and graphite powders in an oxidizing atmosphere and atomic layer deposition of ZnO. Multiple networked WO₃-core/ZnO-shell nanorod sensors showed the response of 281?% at 5 ppm NO₂ at 300?°C. This response value was approximately 9 times larger than that of bare WO₃ nanorod sensors at 5 ppm NO₂. The response values obtained from the WO₃-core/ZnO-shell nanorods in this study were more than 5 times higher than those obtained previously from the SnO₂-core/ZnO-shell nanofibers at the same NO₂ concentration range. The significant enhancement in the response of WO₃ nanorods to NO₂ gas by encapsulating them with ZnO can be accounted for based on the space-charge model.     

Cavity ring down spectroscopy: detection of trace amounts of substance

We describe several applications of cavity ring-down spectroscopy (CRDS) for trace matter detection. NO₂ sensor was constructed in our team using this technique and blue-violet lasers (395–440 nm). Its sensitivity is better than single ppb. CRDS at 627 nm was used for detection of NO₃. Successful monitoring of N₂O in air requires high precision mid-infrared spectroscopy. These sensors might be used for atmospheric purity monitoring as well as for explosives detection. Here, the spectroscopy on sharp vibronic molecular resonances is performed. Therefore the single mode lasers which can be tuned to selected molecular lines are used. Similarly, the spectroscopy at 936 nm was used for sensitive water vapour detection. The opportunity of construction of H₂O sensor reaching the sensitivity about 10 ppb is also discussed.     

Sodium Borohydride as a Protective Agent for the Alkaline Treatment of Sisal Fibers for Polymer Composites

The vegetable fibers used for polymer matrix composites are usually treated to improve their adhesion with the matrix. The chemical treatment with sodium hydroxide (NaOH), although widely used, may damage the fiber surface structure, reducing its strength. The possibility of protecting vegetable fibers against alkaline chemical aggression by using hydride ions (H^–) was investigated in this work. Sisal fibers were modified by immersion in a NaOH aqueous solution (2, 5 and 10% wt/vol), with or without the addition of sodium borohydride (NaBH₄) (1% wt/vol), under variable conditions (immersion time and temperature). The effect of using NaBH₄ was investigated using fiber tensile and pull-out tests, critical length calculation, along with a Weibull statistical analysis. This agent was found to minimize sisal degradation under highly concentrated alkaline conditions in comparison with sisal treated with the pure NaOH solution. The results suggest the 5% wt/vol treatment for 60 min under room temperature in the presence of the hydride ions as the most suitable for sisal. This result may be extended to other vegetable fibers of similar composition and may promote their use in polymer composites.