The growth and spectroscopic characteristics of Ca3Y2(BO3)4:Er laser crystal

The Ca₃Y₂(BO₃)₄:Er³⁺ crystal with a size up to 20 mm×30 mm was grown by the Czochralski method. The absorption spectrum was measured and its absorption peaks were assigned to the corresponding transitions between the Er³⁺ energy levels. A broad emission spectrum from 1429.4 to 1662.8 nm was exhibited from 530 nm wavelength pumping. This crystal is promising as a tunable infrared laser crystal.     

Growth and shape control of orthorhombic Fe5(PO4)4(OH)3·2H2O single crystalline dendrites

Orthorhombic Fe₅(PO₄)₄(OH)₃·2H₂O single crystalline dendritic nanostructures have been synthesized by a facile and reproducible hydrothermal method without the aid of any surfactants. The influences of synthetic parameters, such as reaction time, temperature, the amount of H₂O₂ solution, pH values, and types of iron precursors, on the crystal structures and morphologies of the resulting products have been investigated. The formation process of Fe₅(PO₄)₄(OH)₃·2H₂O dendritic nanostructures is time dependent: amorphous FePO₄·nH₂O nanoparticles are formed firstly, and then Fe₅(PO₄)₄(OH)₃·2H₂O dendrites are assembled via a crystallization-orientation attachment process, accompanying a color change from yellow to green. The shapes and sizes of Fe₅(PO₄)₄(OH)₃·2H₂O products can be controlled by adjusting the amount of H₂O₂ solution, pH values, and types of iron precursors in the reaction system.     

High-resolution electron microscopy of microstructure of SrTiO3/BaZrO3 bilayer thin films on MgO substrates

SrTiO₃/BaZrO₃ heterofilms as buffer layers are deposited on (0 0 1) MgO substrates by an RF-sputtering technique. The atomic structure and the defect configuration at the interfaces are investigated by means of aberration-corrected high-resolution transmission electron microscopy. At the BaZrO₃/MgO interface, two types of interfacial structures, MgO/ZrO₂-type and MgO/BaO-type, are observed. Antiphase boundaries and dislocations are found at the BaZrO₃/MgO interface. The formation of these lattice defects is discussed in terms of film growth and structural imperfections of the substrate surface. At the SrTiO₃/BaZrO₃ interface, a high density of misfit dislocations is observed with different configurations. The formation of these dislocations contributes both to the relaxation of the large misfit strain and to stopping of the further propagation of lattice defects which are formed in the BaZrO₃ layer into the SrTiO₃ layer.     

Mechanochemical metathesis synthesis and characterization of nano-structured MnV2O6·xH2O (x=2, 4)

A solid-state metathesis approach for the synthesis of hydrated MnV₂O₆·xH₂O (x=2, 4) materials driven by mechanochemical activation energy has been demonstrated. The metathesis pathway of forming the desired product is confirmed by the presence of high lattice energy by-product such as NaCl. The structural, optical, and chemical properties of the synthesized materials are examined by powder X-ray diffraction, X-ray photoelectron spectroscopy, thermo gravimetric analysis, scanning electron microscopy, transmission electron microscopy, and diffused reflectance measurements in the UV–vis range. The valence state of Mn and V was determined to be +2 and +5, respectively, for the title compounds and the bandgap values determined showed these materials are likely to be semiconductors.     

Thermal-induced phase transition and assembly of hexagonal metastable In2O3 nanocrystals: A new approach to In2O3 functional materials

This paper reports on the thermal-induced performance of hexagonal metastable In₂O₃ nanocrystals involving in phase transition and assembly, with particular emphasis on the assembly for the preparation of functional materials. For In₂O₃ nanocrystals, the metastable phase was found to be thermally unstable and transform to cubic phase when temperature was higher than 600 °C, accompanied by assembly as well as evolution of optical properties, but the two polymorphs coexisted at the temperature ranging from 600 to 900 °C, during which the content of product phase and crystal size gradually increased upon increasing temperature. The assembly of In₂O₃ nanocrystals can be developed to fabricate In₂O₃ functional materials, such as various ceramic materials, or even desired nano- or micro-structures, by using metastable In₂O₃ nanocrystals as precursors or building blocks. The electrical resistivity of In₂O₃ conductive film fabricated by a hot-pressing route was as low as 3.72×10⁻³ Ω cm, close to that of In₂O₃ single crystal, which is important for In₂O₃ that is always used as conductive materials. The findings should be of importance for both the wide applications of In₂O₃ in optical and electronic devices and theoretical investigations on crystal structures.     

Dynamic process of crystallization of Sb2Se3 from Sb50Se50 amorphous film

Dynamics of crystallization of amorphous antimony-selenium film deposited on carbon substrate have been studied by the high-resolution transmission electron microscopy. The amorphous film was suddenly crystallized at 200°C by heating in vacuum. By the electron beam irradiation crystallization occurred at the focused electron beam region in the amorphous film. The growth process of crystallization by electron beam irradiation was recorded on a video image at the atomic resolution mode. The growth front of crystallization showed nano-concave and -convex shapes. The recrystallization with the different orientation at the first grown crystal have been found, and discussed as the influence of remaining antimony crystallites at the first crystallized film region.     

Growth and scintillation properties of the Na2W2O7 crystal

The growth and scintillation properties of the Na₂W₂O₇ crystal are reported. The solid reaction between Na₂CO₃ and WO₃ is used to synthesise the Na₂W₂O₇ material. The Na₂W₂O₇ single crystal has been grown by the Bridgman method. And the Na₂W₂O₇ single crystal with sizes 14×7×6 mm³ has been achieved. The transmission spectra, the Ultraviolet fluorescence spectra and the X-ray excited luminescence spectra of the Na₂W₂O₇ crystal are measured. The measurement results show that the Na₂W₂O₇ crystal is a promising intrinsic scintillator.     

Densities of Li2O–B2O3 melts

The densities have been systematically measured in xLi₂O–(1−x)B₂O₃ melts of different compositions with Li₂O content varying from x=0 to 0.68 from their respective melting points up to about 1450 K with a modified Archimedean method. The density decreased with increasing temperature for all the melts measured in this work. When x<0.15, the plot of temperature versus density could be well fitted by a quadratic polynomial function, and when x0.15, density decreased linearly with increasing temperature. At a fixed temperature, the density of the melts increased rapidly with Li₂O content, went through a maximum at about x=0.333 (Li₂O–2B₂O₃), and then decreased slowly as Li₂O content was further increased. In addition, the volume expansion coefficient (β) was calculated based on the densities measured in this work, and it was found that a maximum value appeared in the dependence of β on the molar ratio of Li₂O at about x=0.333.     

Nano-crystallization in LaF3–Na2O–Al2O3–SiO2 glass

Aiming at tailoring optical properties, the precipitation of LaF₃ nano-crystals in LaF₃–Na₂O–Al₂O₃–SiO₂ glass-ceramics is studied thoroughly on the nano-scale using advanced transmission electron microscopic techniques. Nano-sized phase-separation droplets enriched in lanthanum and silicon are formed already in the base glass. Within these less than 20 nm large droplets, LaF₃ crystallizes upon heat treatment. The nano-crystallization mechanism revealed is self-limited since growth is restricted by the size of the droplets. An average crystallite size of around 12 nm is achieved with a narrow size distribution since the phase-separation droplets also contain silicon not incorporated into the growing crystal. Instead, excess silicon relocated to the periphery of the pre-existing phase-separation droplets forms a diffusion barrier around the LaF₃ nano-crystals preventing further crystal growth and/or ripening.     

Cs2LiGdCl6 (Ce): New scintillation material

We investigated the scintillation properties of Cs₂LiGdCl₆:Ce³⁺ as a function of the Ce concentration. X-ray excited luminescence spectra of the scintillation material showed broad emission bands between 360 and 460 nm, with two overlapping peaks, due to the d→f transitions on Ce³⁺ ions. The samples provide good scintillation results. The energy resolution was found to be 5.0% (FWHM) at 662 keV for 10% Ce sample. Under γ-ray excitation, Cs₂LiGdCl₆:Ce³⁺ showed three exponential decay time components of about 130–200 ns decay time constant. The light output of the investigated samples was 20,000 photons/MeV for a 10% Ce concentration. The light output deviation from the linear response is within 7% between the energy range of 31 and 1333 keV. Overall, the scintillation properties confirm that Cs₂LiGdCl₆:Ce³⁺ single crystal is a promising candidate for medical imaging and radiation detection.     

Solvothermal synthesis of K2V3O8 nanorods

A solvothermal route has been developed to synthesize K₂V₃O₈ nanorods via the reduction of V₂O₅ using ethanol as the reducing agent as well as the solvent at 200°C. X-ray diffraction and selected area electron diffraction analysis revealed that the as-synthesized products are of tetragonal structure K₂V₃O₈. Transmission electron spectroscopy image showed that the obtained K₂V₃O₈ comprises rod-like nanocrystallites. The formation mechanism of K₂V₃O₈ was studied.     

Flux growth of PbMg1/3Ta2/3O3 single crystals

Single crystals of PbMg_1/3Ta_2/3O₃ (PMT) were grown by the flux method. The PbO–Pb₃O₄–B₂O₃ system was used as a solvent. Transparent and light yellow PMT single crystals of rectangular shape and dimensions up to 10×6×4 mm³ were obtained. For the applied growth conditions only, the crystals of the perovskite structure were grown. X-ray diffraction tests showed that at room temperature PMT exhibits cubic symmetry with lattice parameter a=4.042(1) Å. Dielectric studies pointed to relaxor properties of PMT. The characteristic broad and frequency-dependent maximum of dielectric permittivity was observed at 179.7 K (1 kHz).     

Three-dimensional Bi2Se3 nanopattern films self-assembled with ultrathin nanosheets on the surface of Se nanotubes

Regular three-dimensional (3D) rose-like Bi₂Se₃ nanopattern film is fabricated through a simple chemical route. This nanopattern film is self-assembled with ultrathin Bi₂Se₃ nanosheets having thicknesses of less than 8 nm. The Bi₂Se₃ nanosheets were formed on the surface of Se nanotubes, and the Se nanotubes were used as both the Se resource and the substrate to support the growth of the Bi₂Se₃ nanopattern film. Since several length scales are involved in this confined 3D structure, which are developed at different time, during the formation of the micro-structure, a careful control of these length scales is expected to provide new opportunities for engineering the boundary scattering of phonons of different wavelengths and developing new thermoelectric materials with novel properties.     

Hydrothermal growth of single-crystal CaV6O16·3H2O nanoribbons

CaV₆O₁₆·3H₂O nanoribbons have been prepared by the hydrothermal method in the presence of sodium dodecyl sulfate (SDS) at 160°C for 10 h. X-ray diffraction pattern indicates that the sample is monoclinic phase of CaV₆O₁₆·3H₂O with the lattice contents a=12.18 Å, b=3.598 Å, c=18.39 Å, β=118.03°. Field emission scanning electron microscopy shows that the nanoribbons have widths in the range of 150–500 nm, thicknesses of 30–60 nm and lengths of 500 mm X-ray photoelectron spectrum measurements further confirm the formation of the CaV₆O₁₆·3H₂O phase. The formation of CaV₆O₁₆·3H₂O nanoribbons is a self-assembling process, in which surfactant SDS plays the role of soft template.     

Synthesis of superparamagnetic Mn3O4 nanocrystallites by ultrasonic irradiation

Nanocrystalline Mn₃O₄ has been synthesized by ultrasonic irradiation of Mn acetate solution in water. Analysis of its X-ray diffraction data shows formation of a phase-pure compound with an average particle size of about 15 nm. DC magnetization measurements as a function of temperature and field show a reduced ferrimagnetic transition temperature as compared to those reported for the bulk , and a subsequent observation of superparamagnetic behavior at 40 K. The observed magnetic properties are suggestive of formation of a single domain magnetically ordered Mn₃O₄ nanoparticles below their ferrimagnetic transition temperature.     

High-velocity banding structure in the laser-resolidified hypoperitectic Ti47Al53 alloy

Stability analysis of a growing solid/liquid interface is the fundamental concept of modern solidification theory. Here, serial laser rapid solidification experiments were performed on a hypoperitectic Ti₄₇Al₅₃ alloy to explore the dendritic growth behavior near the limit of high-velocity absolute stability. SEM and TEM techniques were carried out to investigate the microstructure and identify the phase composition. By adopting an improved sampling method of TEM, the growth morphology evolution of the laser-resolidified layer was observed directly and high-velocity banding structure was firstly detected in Ti–Al peritectic alloys. The high-velocity banding structures are parallel to the solid/liquid interface (normal to the growth direction) and made of the oscillation structures grown alternatively in modes of cell and plane morphologies. In light bands with cellular growth mode, all dislocation assembles are parallel to the growth direction and forms the cell boundaries, while all dislocation distributes randomly in dark bands. The determined growth velocity range for the appearance of high-velocity banding structures is about 0.51.1 m s⁻¹ according to the rapid solidification experiments, and the origin of the banding agrees well with the prediction of the CGZK phenomenological model (Acta Metal. Mater. 40 (1992) 983).     

Growth and characterization of nanostructured Al2O3/YAG/ZrO2 hypereutectics with large surfaces under laser rapid solidification

The preparation of large bulk oxide eutectics with homogeneous and dense structure in nano-scale by melt growth method is a difficult challenge. Fully dense, homogeneous and crack-free ternary nanostructured Al₂O₃/YAG/ZrO₂ hypereutectic plate with large surface is successfully obtained by laser remelting. The hypereutectic in selected composition presents an ultra-fine eutectic-like microstructure consisting of alternating interpenetrating Al₂O₃, YAG and ZrO₂ lamellae with mean interphase spacing of about 150 nm, which is much smaller than the ternary eutectic composition grown at the same growth conditions. With the increase of laser scanning rate, the lamellar spacing is rapidly decreased. The minimum value obtained is 50 nm. The analysis indicates that the strong faceted growth behavior and cooperative branching of the component phases related with high entropies of fusion and large kinetic undercooling during laser rapid solidification are the primary formation reasons for the irregular eutectic growth morphology. Furthermore, the unique cellular microstructure with complex structure is also observed at high growth rate, and their formation mechanism and effect of the composition on the microstructure are discussed.     

Synthesis of Y2O3:Eu phosphors by bicontinuous cubic phase process

A novel approach for preparation of red-emitting europium-doped yttrium oxide phosphor (Y₂O₃:Eu) by using the bicontinuous cubic phase (BCP) process was reported in this paper. The BCP system was composed of anionic surfactant sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and aqueous yttrium nitrate/europium nitrate solution. Energy dispersive spectrometer analysis revealed the homogeneous precipitation occurred in the BCP structure. Thermogravimetric analysis measurements indicated the precursor powder was europium-doped yttrium hydroxide, Y_1−xEu_x(OH)₃. Scanning electron microscopy micrographs showed the precursor powder had a primary size about 30 nm and narrow size distribution. After heat treatment in furnace above 700 °C for 4 h, high crystallinity Y₂O₃:Eu phosphors was obtained. However, the primary size of particles grew to 50–200 nm and the dense agglomerates with a size below 1 μm were formed. X-ray diffraction patterns indicated the crystal structure of precursor powders and Y₂O₃:Eu phosphors were amorphous and body-centered cubic structure, respectively. The photoluminescence analysis showed that the obtained Y₂O₃:Eu phosphor had a strong red emitting at 612 nm and the quenching started at a Eu concentration of 10 mol%. This study indicated that the BCP process could be used to prepare the highly efficient oxide-based phosphors.     

Sn3O4 single crystal nanobelts grown by carbothermal reduction process

This article reports on the growth of single crystal Sn₃O₄ nanobelts and SnO by a carbothermal reduction process in two different regions of a furnace tube. Even though intermediate tin oxide compounds (Sn₃O₄) have been observed experimentally, the study of structures based on them is a challenging task. Characterization data allowed us to propose that Sn₃O₄ nanobelts grew by vapor–solid mechanism while SnO grew by self-catalyst vapor–liquid–solid mechanism. Electrical measurements of a single Sn₃O₄ nanobelt were performed at different temperatures, revealing undoped semiconductor characteristics.     

Crystallization behavior and hydrophilic performances of V2O5–TiO2 films prepared by sol–gel dip-coating

Homogeneous and transparent V₂O₅–TiO₂ composite nanometer thin films were prepared on glass substrates by sol–gel processing and dip-coating technique. The films as well as the dried powder of bulk gel were characterized by different techniques like X-ray diffraction (XRD), high-resolution scanning electron microscopy (HRSEM), atomic force microscope (AFM) and thermogravimetry–differential thermal analysis (TG–DTA). The hydrophilicity of the films was determined by measuring the water contact angles on the films. The results showed that the dopant of V₂O₅ on TiO₂ thin films could produce a visible-light response to the films, and the introduction of V₂O₅ could suppress the structural phase transition and crystal growth of TiO₂ crystal. Finally, the relationship between crystalline size and hydrophilicity under sunlight was investigated in this article.