Study of complex impedance spectroscopic properties of the KFeP2O7 compound

The KFeP₂O₇ compound was prepared by the conventional solid-state reaction. The sample was characterized by X-ray powder diffraction. The AC electrical conductivity and the dielectric relaxation properties of this compound have been investigated by means of impedance spectroscopy measurements over a wide range of frequencies and temperatures, 200 Hz–5 MHz and 553–699 K, respectively. Both impedance and modulus analysis exhibit the grain and grain boundary contribution to the electrical response of the sample. The temperature dependence of the bulk and grain boundary conductivity were found to obey the Arrhenius law with activation energies Eg?=?0.94 (3)?eV and Egb?=?0.89 (1)?eV. The grain-and-grain boundary conductivities at 573 K are 1.07?×?10^?4 and 1.16?×?10^?5 (Ω^?1 cm^?1). The scaling behavior of the imaginary part of the complex impedance suggests that the relaxation describes the same mechanism at various temperatures. The near value of the activation energies obtained from the equivalent circuit, conductivity data, and analysis of M″ confirms that the transport is through ion hopping mechanism.     

Ionic conductivity in tysonite-type solid solutions La1−xBaxF3−x

The ionic conductivity of single crystals of tysonite-type solid solutions La_1?xBa_xF_3?x(0?x?0.095) has been studied parallel and perpendicular to the crystallographic c axis in the temperature range 293–1300 K. Three regions can be discerned in the compositional dependence of the ionic conductivity: (i) the “pure” crystal, in which at room temperature no exchange occurs between different types of anion sites in the tysonite structure; (ii) an intermediate region(0 < x < 7 × 10^-2) which reveals changes in both the conductivity activation enthalpy and the magnitude of the conductivity; (iii) a concentrated solid-solution region (x > 7 × 10^-2), where fluoride ions interchange easily among the different anion sublattices. Diffusion coefficients calculated from ionic conductivity results, are in good agreement with those calculated from ¹⁹F NMR measurements. Using the present data, along with ¹⁹F NMR data, dielectric relaxation data and structural considerations, mechanisms governing the ionic conductivity are proposed.     

Electrical properties and conduction mechanism in the sodium nickel diphosphate

The Na_3.6Ni_2.2(P₂O₇)₂ compound was obtained by the conventional solid-state reaction. The sample was characterized by X-ray powder diffraction and vibrational and impedance spectroscopy. The AC electrical conductivity and the dielectric relaxation properties of this compound have been investigated by means of impedance spectroscopy measurements over a wide range of frequencies and temperatures, 209 kHz–1 MHz and 564–729 K, respectively. Dielectric data were analyzed using complex electrical modulus M* at various temperatures. The peak positions ω _m of M″ spectra shift toward higher frequencies with increase in temperature. The AC conductivity data fulfill the power law. Application of the correlated barrier hopping model revealed that the ionic conduction takes place by single-polaron and bipolaron hopping processes.     

Li<Superscript>+</Superscript> ion conductivity and transport properties of LiYP<Subscript>2</Subscript>O<Subscript>7</Subscript> compound

A lithium yttrium diphosphate LiYP₂O₇ was prepared by a solid-state reaction method. Rietveld refinement of the X-ray diffraction pattern suggests the formation of the single phase desired compound with monoclinic structure at room temperature. The infrared and Raman spectrum of this compound was interpreted on the basis of P₂O₇ ^4? vibrations. The AC conductivity was measured in the frequency range from 100 to 10⁶ Hz and temperatures between 473 and 673 K using impedance spectroscopy technique. The obtained results were analyzed by fitting the experimental data to the equivalent circuit model. The Cole–Cole diagram determined complex impedance for different temperatures. The angular frequency dependence of the AC conductivity is found to obey Jonscher’s relation. The temperature dependence of σ _AC could be described in terms of Arrhenius relation with two activation energies, 0.87 eV in region I and 1.36 eV in region II. The study of temperature variation of the exponent(s) reveals two conduction models: the AC conduction dependence upon temperature is governed by the correlated barrier hopping (CBH) model in region I (T < 540 K) and non-overlapping small polaron tunneling (NSPT) model in region II (T > 540 K). The near value of activation energies obtained from the equivalent circuit and DC conductivity confirms that the transport is through ion hopping mechanism dominated by the motion of the Li⁺ ion in the structure of the investigated material.     

Thermodynamic properties and application of CBH model in the ac conductivity of LiNi1.5P2O7 ceramic

The LiNi_1.5P₂O₇ compound was prepared by the solid-state reaction method at 923 K and characterized through XRD and Raman spectroscopy techniques. The impedance spectroscopy measurements were performed in the frequency and the temperature range (300 Hz–5 MHz) and (633–729 K), respectively. The ac conductivity for grain contribution is interpreted using the universal Jonscher’s power low. The exponent n decreases with increasing temperature which reveals that the conduction inside the studied material is insured by the correlated barrier hopping (CBH) model. The parameters of CBH model were determined showing that the ac conduction is realised by single-polaron hopping mechanism. Thermodynamic parameters such as the free energy for dipole relaxation ΔF, the enthalpy ΔH, and the change in entropy ΔS have been calculated.     

Grain size effects on dynamics of Li-ions in Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> glass-ceramic nanocomposites

Li₃V₂(PO₄)₃ glass-ceramic nanocomposites, based on 37.5Li₂O-25V₂O₅-37.5P₂O₅ mol% glass, were successfully prepared via heat treatment (HT) process. The structure and morphology were investigated by X-ray diffraction (XRD) and scanning electron microscope (SEM). XRD patterns exhibit the formation of Li₃V₂(PO₄)₃ NASICON type with monoclinic structure. The grain sizes were found to be in the range 32–56 nm. The effect of grain size on the dynamics of Li⁺ ions in these glass-ceramic nanocomposites has been studied in the frequency range of 20 Hz–1 MHz and in the temperature range of 333–373 K and analyzed by using both the conductivity and modulus formalisms. The frequency exponent obtained from the power law decreases with the increase of temperature, suggesting a weaker correlation among the Li⁺ ions. Scaling of the conductivity spectra has also been performed in order to obtain insight into the relaxation mechanisms. The imaginary modulus spectra are broader than the Debye peak-width, but are asymmetric and distorted toward the high frequency region of the maxima. The electric modulus data have been fitted to the non-exponential Kohlrausch–Williams–Watts (KWW) function and the value of the stretched exponent β is fairly low, suggesting a higher ionic conductivity in the glass and its glass-ceramic nanocomposites. The advantages of these glass-ceramic nanocomposites as cathode materials in Li-ion batteries are shortened diffusion paths for Li⁺ ions/electrons and higher surface area of contact between cathode and electrolyte.     

On the effect of SHI irradiation on dielectric properties of Y3+xFe5−xO12 (x=0.0–0.6) system

The present work aims to investigate the pre- and post-effect of 50 MeV Li³⁺ ion irradiation at a fluence of 5×10¹³ ions/cm² on the dielectric properties of Y_3+xFe_5?xO₁₂, x=0.0, 0.2, 0.4 and 0.6, garnet system over broad temperature, 300–673 K, and frequency, 100 Hz–13 MHz, ranges. Thermal variation of ac resistivity measurements suggests that the mechanism responsible for conduction in the system is polaron hopping. The observed modifications in dielectric properties after swift heavy ion irradiation are mainly due to the modifications of the metal–insulator contacts due to radiation damage-induced disorder and irradiation-induced point/cluster of defects in the material and also compressive strain generated in the lattice structure. The electric modulus presentation and the complex impedance spectral analysis have been employed to study the relaxation process. The YFeO₃ phase is found to be irradiation hard phase as compared with the garnet phase.     

Phase transition and electrical investigation in lithium copper pyrophosphate compound Li<Subscript>2</Subscript>CuP<Subscript>2</Subscript>O<Subscript>7</Subscript> using impedance spectroscopy

Lithium pyrophosphate compound Li₂CuP₂O₇ has been synthesized through solid state reaction method. FTIR and XRD results, realized at room temperature, indicate respectively the dominant feature of pyrophosphate anion (P₂O₇)^4? and a pure monoclinic phase with I2/a space group. Electrical and dielectric properties have been studied using impedance spectroscopy complex over a wide temperature (576–710 K) and frequency (209 Hz–1 MHz) range. From the direct and alternative conductivities (DC and AC), electrical conduction is found to be thermally activated process. The frequency-dependent AC conductivity obeys Jonscher’s universal power law σ_AC~Aω^s. The differential scanning calorimetry spectrum discloses phase transition at 622 K.     

Lithium-ionic diffusion and electrical conduction in the Li7La3Ta2O13 compounds

The electrical properties and the mechanism of lithium ionic diffusion in the Li₇La₃Ta₂O₁₃ compounds were investigated. The bulk and total conductivity at 300 K of the Li₇La₃Ta₂O₁₃ compound are about 3.3 × 10^? 6 S/cm and 2.6 × 10^? 6 S/cm, respectively. The activation energy of bulk and total conductivity is in the range of 0.38–0.4 eV. A prominent internal friction peak in Li₇La₃Ta₂O₁₃ compounds was observed around 280 K at 0.5 Hz, which is actually composed of two subpeaks (P₁ peak at lower temperature and P₂ peak at higher temperature). From the shift of peak position with frequency, the activation energy of 1.0 eV and the pre-exponential factor of relaxation time in the order of 10^? 18–10^? 21 s were obtained if one assumes Debye relaxation processes. These values of relaxation parameters strongly suggest the existence of interaction between the relaxation species (here lithium ions or vacancies). Based on the coupling model, the relaxation activation energies are deduced as 0.45 eV and the pre-exponential factor of relaxation time as 10^? 15 s. Judging from these relaxation parameters and the similarity of structure between Li₇La₃Ta₂O₁₃ and Li₅La₃Ta₂O₁₂ compounds, the P₁ and P₂ peaks are suggested to be related with the lithium ionic diffusion between 48g?48g and 24d?48g.     

Synthesis,refinement of the structure,and AC conductivity behavior of sodium lithium orthonavadates

The Na _x Li_1-x CdVO₄ (x = 0.5, 1) orthovanadates were prepared using a solid-state reaction method. The x-ray diffraction patterns (XRDP) of both materials reveal the formation of the Na₂CrO₄ structure. Vibrational study confirms the existence of [VO₄]^3? group. Electrical measurements of our compounds have been investigated using complex impedance spectroscopy (CIS) in the frequency and temperature range 209 Hz–1 MHz and 589–703 K, respectively. Nyquist plots reveal the presence of tow contributions, an equivalent circuit was proposed. DC conductivity shows electrical conduction in the material as a thermally activated process. The AC conductivity is explained using the non-overlapping small polaron tunneling (NSPT) conduction mechanism. A relationship between crystal structure and ionic conductivity was established and discussed.     

Bi<Subscript>13-x</Subscript>Me<Subscript>x</Subscript>Mo<Subscript>5</Subscript>O<Subscript>34±δ</Subscript> (Me = Mg,Ca, Sr,Ba) solid solutions: synthesis and properties

A series of complex oxides Bi_13-xMe_xMo₅O_34±δ, Me = Mg, Ca, Sr, Ba were synthesized and studied. The solid solutions ranges and polymorphic modifications limits were determined. High temperature X-ray powder diffraction measurements showed the deviation of unit cell parameters dependence versus temperature from the linear function. Processes of forming of ceramic samples based on the synthesized powders were analyzed, and dense ceramic samples were obtained. Impedance spectroscopy displayed the changes of slope of Arrhenius plots which correspond with the HT-XPRD measurements. The presence of two different forms of monoclinic modification was supposed. The studied materials are promising ionic conductors, with the highest conductivity values about 6?×?10^?3 S cm^?1 at 973 K and 1.4?×?10^?4 S cm^?1 at 623 K.     

50 MeV Li3+ ion irradiation effect on structural, electrical, and dielectric properties of PVA-based nanocomposite polymer electrolytes

Nanocomposite polymer electrolyte thin films of polyvinyl alcohol (PVA)-orthophosphoric acid (H₃PO₄)-Al₂O₃ have been prepared by solution cast technique. Films are irradiated with 50 MeV Li³⁺ ions having four different fluences viz. 5?×?10¹⁰, 1?×?10¹¹, 5?×?10¹¹, and 1?×?10¹² ions/cm². The effect of irradiation on polymeric samples has been studied and characterized. X-ray diffraction spectra reveal that percent degree of crystallinity of samples decrease with ion fluences. Glass transition and melting temperatures have been also decreased as observed in differential scanning calorimetry. A possible complexation/interaction has been shown by Fourier transform infrared spectroscopy. Temperature-dependent ionic conductivity shows an Arrhenius behavior before and after glass transition temperature. It is observed that ionic conductivity increases with ion fluences and after a critical fluence, it starts to decrease. Maximum ionic conductivity of ～2.3?×?10^?5 S/cm owing to minimum activation energy of ～0.012 eV has been observed for irradiated electrolyte sample at fluence of 5?×?10¹¹ ions/cm². The dielectric constant and dielectric loss also increase with ion fluences while they decrease with frequency. Transference number of ions shows that the samples are of purely ionic in nature before and after ion irradiation.     

AC conductivity and mechanism of conduction study of lithium barium pyrophosphate Li<Subscript>2</Subscript>BaP<Subscript>2</Subscript>O<Subscript>7</Subscript> using impedance spectroscopy

The Li₂BaP₂O₇ compound has been obtained by the conventional solid-state reaction and characterized by X-ray powder diffraction. The title material crystallizes in the monoclinic system with C2/c space group. Electrical properties of the compound have been studied using complex impedance spectroscopy in the frequency range 200 Hz–5 MHz and temperature range 589–724 K. Temperature dependence of the DC conductivity and modulus was found to obey the Arrhenius law. The obtained values of activation energy are different which confirms that transport in the titled compound is not due to a simple hopping mechanism. AC conductivity measured follows the power-law dependence σ _AC?～?ω ^s typical for charge transport. Therefore, the experimental results are analyzed with various theoretical models. Temperature dependence of the power law exponent s strongly suggests that tunneling of large polarons is the dominant transport process.     

Electrical transport characteristics of ZnO–Bi2O3–B2O3 glasses

Optically clear glasses in the ZnO–Bi₂O₃–B₂O₃ (ZBBO) system were fabricated via the conventional melt-quenching technique. Dielectric constant and loss measurements carried out on ZBBO glasses unraveled nearly frequency (1 kHz–10 MHz)-independent dielectric characteristics associated with significantly low loss (D?=?0.004). However, weak temperature response was found with temperature coefficient of dielectric constant 18?±?4 ppm °C^?1 in the 35–250 °C temperature range. The conduction and relaxation phenomena were rationalized using universal AC conductivity power law and modulus formalism respectively. The activation energy for relaxation determined using imaginary parts of modulus peaks was 2.54 eV which was close to that of the DC conduction implying the involvement of similar energy barriers in both the processes. Stretched and power exponents were temperature dependent. The relaxation and conduction in these glasses were attributed to the hoping and migration of Bi³⁺ cations in their own and different local environment.     

Structure,thermal behavior,and dielectric properties of new cesium hydrogen sulfate arsenate: Cs<Subscript>2</Subscript>(HSO<Subscript>4</Subscript>)(H<Subscript>2</Subscript>AsO<Subscript>4</Subscript>)

Synthesis and structural characterization by single-crystal X-ray diffraction method, thermal behavior, and electrical proprieties are given for a new compound with a superprotonic phase transition Cs₂(HSO₄)(H₂AsO₄). The title compound crystallizes in the monoclinic system with the P2₁/n space group. The structure contains zigzag chains of hydrogen-bonded anion tetrahedra that extend in the [010] direction. Each tetrahedron is additionally linked to a tetrahedron neighboring chain to give a planar structure with hydrogen-bonded sheets lying parallel to (10ī). The existence of O–H and (S/As)–O bonds in the structure at room temperature has been confirmed by IR and Raman spectroscopy in the frequency ranges 4000–400 cm^?1and 1200–50 cm^?1, respectively. Differential scanning calorimetry analysis of the superprotonic transition in Cs₂(HSO₄)(H₂AsO₄) showed that the transformation to high temperature phase occurs at 417 K by one-step process. Thermal decomposition of the product takes place at much higher temperatures, with an onset of approximately 534 K. The superprotonic transition was also studied by impedance and modulus spectroscopy techniques. The conductivity in the high temperature phase at 423 K is 1.58 × 10^?4 Ω^?1 cm^?1, and the activation energy for the proton transport is 0.28 eV. The conductivity relaxation parameters associated with the high disorder protonic conduction have been examined from analysis of the M”/M”_max spectrum measured in a wide temperature range. Transport properties of this material appear to be due to the proton hopping mechanism.     

Low-temperature sintering effects on NASICON-structured LiSn<Subscript>2</Subscript>P<Subscript>3</Subscript>O<Subscript>12</Subscript> solid electrolytes prepared via citric acid-assisted sol-gel method

LiSn₂P₃O₁₂ with sodium (Na) super ionic conductor (NASICON)-type rhombohedral structure was successfully obtained at low sintering temperature, 600 °C via citric acid-assisted sol-gel method. However, when the sintering temperature increased to 650 °C, triclinic structure coexisted with the rhombohedral structure as confirmed by X-ray diffraction analysis. Conductivity–temperature dependence of all samples were studied using impedance spectroscopy in the temperature range 30 to 500 °C, and bulk, grain boundary and total conductivity increased as the temperature increased. The highest bulk conductivity found was 3.64?×?10^?5 S/cm at 500 °C for LiSn₂P₃O₁₂ sample sintered at 650 °C, and the lowest bulk activation energy at low temperature was 0.008 eV, showing that sintering temperature affect the conductivity value. The voltage stability window for LiSn₂P₃O₁₂ sample sintered at 600 °C at ambient temperature was up to 4.4 V. These results indicated the suitability of the LiSn₂P₃O₁₂ to be exploiting further for potential applications as solid electrolytes in electrochemical devices.     

Conductivity behavior of the new pyrophosphate NaNi<Subscript>1.5</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>

NaNi_1.5P₂O₇ compound was obtained by the classic ceramic method at high temperature and was characterized by XRD. It was found to crystallize in the triclinic symmetry with the P-1 space group. The electrical conductivity and modulus characteristics of the system have been investigated in the temperature and the frequency range 586–723 K and 200 Hz–1 MHz, respectively, by means of impedance spectroscopy. The ac conductivity for grain contribution was interpreted using the universal Jonscher’s power law. The exponent s decreased with increasing temperature revealing that the conduction inside the studied material is insured by the correlated barrier hopping (CBH) model. The conduction mechanism was explained with the help of Elliot’s theory, and the Elliot’s parameters were determined. Thermodynamic parameters such as the free energy for dipole relaxation ΔG, the enthalpy ΔH, and the change in entropy ΔS have been calculated.     

Enhancement in electrochemical properties of ionic liquid-based nanocomposite polymer electrolytes by 100 MeV Si9+ swift heavy ion irradiation

Swift heavy ion (SHI) irradiation has been used as a tool to enhance the electrochemical properties of ionic liquid-based nanocomposite polymer electrolytes dispersed with dedoped polyaniline (PAni) nanorods; 100 MeV Si⁹⁺ ions with four different fluences of 5?×?10¹⁰, 1?×?10¹¹, 5?×?10¹¹, and 1?×?10¹² ions cm^?2 have been used as SHI. XRD results depict that with increasing ion fluence, crystallinity decreases due to chain scission up to fluence of 5?×?10¹¹ ions cm^?2, and at higher fluence, crystallinity increases due to cross-linking of polymer chains. Ionic conductivity, electrochemical stability, and dielectric properties are enhanced with increasing ion fluence attaining maximum value at the fluence of 5?×?10¹¹ ions cm^?2 and subsequently decrease. Optimum ionic conductivity of 1.5?×?10^?2 S cm^?1 and electrochemical stability up to 6.3 V have been obtained at the fluence of 5?×?10¹¹ ions cm^?2. Ac conductivity studies show that ion conduction takes place through hopping of ions from one coordination site to the other. On SHI irradiation, amorphicity of the polymer matrix increases resulting in increased segmental motion which facilitates ion hopping leading to an increase in ionic conductivity. Thermogravimetric analysis (TGA) measurements show that SHI-irradiated nanocomposite polymer electrolytes are thermally stable up to 240–260 °C.     

XRD,XPS, SEM/EDX and broadband impedance spectroscopy study of pyrophosphate (LiFeP2O7 and Li0.9Fe0.9Ti0.1P2O7) ceramics

LiFeP₂O₇ and Li_0.9Fe_0.9Ti_0.1P₂O₇ were synthesised by solid-state reaction and ceramics were sintered. The structure of compounds was studied in the temperature range 300–700 K by X-ray diffraction. Ceramics’ surfaces were investigated by scanning electron microscope. Binding energies of Fe 2p, P 2p and O 1s core levels at ceramics’ surfaces have been determined by X-ray photoelectron spectroscopy and different valence states of Fe and P were detected. Elemental compositions of the compounds were studied by energy dispersive X-ray spectrometer. Impedance spectroscopy was performed in the frequency range 10 Hz–3 GHz and in the temperature interval 400–700 K. The changes of the activation energy of ionic conductivity at 528 and 550 K for LiFeP₂O₇ and Li_0.9Fe_0.9Ti_0.1P₂O₇, respectively, were found. The phenomena can be related to disordering in the unit cells of the compounds.     

Synthesis of Al2TiO5 and its effect on the properties of chitosan–NH4SCN polymer electrolytes

In this paper, Al₂TiO₅ ceramic material has been synthesised and used as filler in polymer electrolyte system to enhance the conductivity. The precursor sintered at 1,050 °C and contained 0.08 mole of aluminium nitrate gives the best and complete formation of Al₂TiO₅. Composite polymer electrolytes of chitosan–NH₄SCN containing different amount of home-made Al₂TiO₅ were prepared by solution casting. The addition of filler has enhanced the conductivity of polymer electrolyte. The sample 57 wt% chitosan–38 wt% NH₄SCN–5 wt% Al₂TiO₅ exhibited the highest electrical conductivity of 2.10?×?10^?4 S cm^?1 at room temperature. The presence of the Al₂TiO₅ creates favourable pathways for ionic conduction through Lewis acid–base type interactions between ionic species and O/OH surface groups on alumina filler grains. In addition, the space charge region created by the presence of Al³⁺ could attract SCN^?1 ions, thus immobilise it and increase the transport number of the cation. Degree of crystallinity is calculated from the deconvoluted X-ray diffraction patterns and it shows that the lowest degree of crystallinity is achieved when 5 wt% of filler is added. In Fourier transform infrared study, the carboxamide band of the polymer is observed to shift to higher wave number from 1,629 to 1,634 cm^?1, confirming the formation of chitosan–NH₄SCN–Al₂TiO₅ complexes. The morphology of composite polymer electrolyte has been studied using scanning electron microscopy at room temperature.