Continuous-flow extraction of organophosphorus pesticides coupled on-line with high-performance liquid chromatography

A continuous-flow extraction system coupled on-line with a high-performance liquid chromatograph with an ultraviolet detector is used to study the extraction of three organophosphorus pesticides (fenthion, azinphos methyl and diazinon) from aqueous samples with n-heptane as the organic solvent. Diazinon was not extracted significantly. The influence on the extraction of different parameters (coil length, flow rate and phase volume ratio) were studied. The calibration graphs are linear for 0.5–7 mg l^?1 and 8–20 mg l^?1 foor azinphos methyl where the percentage extraction (E%) is 90% and 70%, respectively, and up to 4 mg l^?1 for fenthion, where the E% is 33%. The detection limits and the relative standard deviations are 0.04 and 0.09 mg l^?1, and 3.4 and 5.3%, for azinphos methyl fenthion, respectively. Other pesticides and related compounds were found not to interfere. The sample throughput of this method was 15 h^?1.     

Low density miniaturized homogeneous liquid-liquid extraction: a new high throughput sample preparation technique for the determination of polar pesticides in cow milk

The application of miniaturized homogeneous liquid-liquid extraction (MHLLE) technique as a simple, inexpensive, quick and efficiency clean up method has been evaluated for determination of diazinon, alachlor, chlorpyrifos and butachlor in cow milk samples. Methanol was used as extraction solvent for the extraction of analytes from cow milk samples and then, methanol phase was extracted and cleaned up by MHLLE method. In this method, butyl acetate was added to methanol phase and after addition of water, butyl acetate was separated from methanol phase and injected to the GC/TSD instrument. The concentration ranges were from 1.0–1000.0 ng/mL for diazinon and chlorpyrifos and from 5.0–1000.0 ng/mL for alachlor and butachlor. The limits of detection were 0.4, 1.6, 0.3 and 1.4 ng/mL for diazinon, alachlor, chlorpyrifos and butachlor, respectively. Finally, the extraction method was successfully applied to the analysis of raw cow milk samples.     

Analysis of pesticides in surface water in remote areas in Vietnam: Coping with matrix effects and test of long-term storage stability

During the last years, the increased use of pesticides and growing awareness of associated environmental and health problems have led to the implementation of various monitoring programmes in South-East Asia. The introduction of numerous new active ingredients and commercial pesticide formulations in connection with reports on pesticide-related health problems strongly indicate that the analytical procedures should be tested and evaluated for currently used pesticides. Coping with matrix effects and ensuring pesticide stability when samples are taken in remote areas are paramount. In the present study, we tested an analytical method that targets nine currently used pesticides in surface water in northern Vietnam. The method consists of solid phase extraction, storage at ?18°C in the adsorbed state, and capillary gas chromatography with nitrogen-phosphorus-detection of five insecticides (dichlorvos, fenobucarb, dimethoate, fenitrothion, and chlorpyrifos), three fungicides (chlorothalonil, metalaxyl, and edifenphos) and one herbicide (atrazine). We evaluated the potential analytical bias caused by matrix effect and investigated its possible causes. We also tested the long-term stability (up to 9 months) of pesticides adsorbed to Carbopack SPE cartridges when stored at temperatures below ?18°C. Adopting a matrix-matched calibration technique considerably improved the recovery values of seven of the nine tested pesticides. At spiking levels of 0.1?µg?L^?1 and 1?µg?L^?1 and after storage of 119 days at ?18°C, recovery values of these pesticides ranged from 67% to 107% and from 67% to 155%, respectively. For the remaining two pesticides recovered at 53–55% at both spiking levels – dichlorvos and chlorothalonil – the method could still be useful for semi-quantitative analysis or as a screening tool. Even though the general recommendation is to minimise storage time to reduce pesticides degradation, our results showed that storage times up to nine months can be adopted for atrazine, metalaxyl, fenitrothion, and chlorpyrifos.     

Headspace single-drop microextraction of common pesticide contaminants in honey–method development and comparison with other extraction methods

In the present study the main factors that may influence the headspace single-drop microextraction (HS-SDME) of common pesticide contaminants (diazinon, lindane, chlorpyrifos ethyl, p,p′-DDE, and endosulfan) that may occur in honey were determined and an analytical protocol was further developed by the use of a multivariate optimization. The HS-SDME analytical method developed and two more analytical protocols for the determination of pesticides in honey: (i) by direct SDME (D-SDME), and (ii) by liquid–liquid extraction (LLE), were further validated for the determination of target analytes. The three methods were also applied in the same real honey samples and results were further discussed. By D-SDME, LODs ranged from 0.04?µg?kg^?1 for β-endosulfan to 2.40?µg?kg^?1 for diazinon and repeatability expressed as %RSD from 3 for lindane to 15 for diazinon and chlorpyrifos methyl; by HS-SDME, LODs ranged from 0.07?µg?kg^?1 for p,p′-DDE to 12.54?µg?kg^?1 for chlorpyrifos methyl and repeatability expressed as %RSD from 11 for chlorpyrifos methyl to 19 for p,p′-DDE; by LLE, LODs ranged from 0.09?µg?kg^?1 for β-endosulfan to 19.31?µg?kg^?1 for diazinon and repeatability expressed as %RSD from 6 for p,p′-DDE to 11 for lindane. For all target pesticides but p,p′-DDE that could not be recovered by D-SDME method tested. The proposed HS-SDME optimized in this study was shown to be the method of choice for the determination of diazinon in honey whereas the most favourable analytical characteristics from the comparative study performed were achieved by D-SDME.     

Determination of Atrazine,Simazine, Alachlor,and Metolachlor in Surface Water Using Dispersive Pipette Extraction and Gas Chromatography–Mass Spectrometry

Four commonly found pesticides (alachlor, atrazine, metolachlor, and simazine) in surface water were determined using dispersive pipette extraction followed by gas chromatography–mass spectrometry. The rapid mixing and equilibrium between the dispersive pipette extraction adsorbent and water sample resulted in fast and efficient extraction. Using only 5?mL of water sample, the estimated time consumption for extraction of each sample was less than 5?min. Method validation was performed to evaluate accuracy, precision, linearity, the limits of detection, and the limits of quantitation. Average recovery of above 90% was obtained with relative standard deviations below 10%, which indicated good accuracy and precision of the dispersive pipette extraction method. Coefficients of determination were all above 0.9901 and showed good linearity. For the four pesticides studied using the current method, the limits of detection ranged from 7 to 40?ng?L^?1, and limits of quantitation were from 20 to 130?ng?L^?1. Method validation results supported the application of the current method for drinking water safety monitoring per National Primary Drinking Water Regulations established by the US Environmental Protection Agency. Water samples from Lake Lanier and Stone Mountain Lake (Georgia, USS) were analyzed with this method as a preliminary work for a larger scale drinking water quality study in the future. Trace amounts of simazine and atrazine were found in lake water samples, but both were below the regulation levels of the US Environmental Protection Agency.     

Application of the molecularly imprinted solid-phase extraction to the organophosphate residues determination in strawberries

This study describe an analytical method employing gas chromatography (GC) using flame photometric detection that has been developed for the simultaneous determination of organophosphate pesticides (diazinon, disulfoton, parathion, chlorpyrifos and malathion) in strawberry samples. For this purpose, molecularly imprinted solid-phase extraction was applied as a sample preparation technique. The method was linear in the ranges from 0.10 to 1.00?μg?g^?1, for diazinon, disulfoton, parathion and chlorpyrifos, and 0.10 to 2.00?μg?g^?1 for malathion with r?>?0.99. The detection limits (LD) ranged from 0.02 to 0.05?μg?g^?1. Recovery studies yielded average recoveries in the range of 65.25 to 87.70?%. These results showed the potential of this technique for organophosphate residue monitoring in strawberry samples.     

Residues of some organophosphorus pesticides on and in fruits and vegetables available in Poland,an assessment based on the European union regulations and health assessment for human populations

Abstract

The use of organophosphorus pesticides is undeniably beneficial in agriculture and veterinary medicine, but their excessive use can pollute the environment, as well as contaminate foodstuffs. The objective of this study was to assess contamination of vegetables and fruits available in Poland by organophosphate pesticides (ethoprophos, diazinon, chlorpyrifos, chlorpyrifos-methyl, parathion-methyl, fenchlorphos, merfos,, as well as to assess a potential health risk posed to consumers. The pesticide content was determined by gas chromatography-mass spectrometry (GC-MS). The pesticides were detected in the peel and pulp of vegetables and fruits from Polish crops, as well as imported ones. Pesticide levels in most products were higher in the peel than in the pulp. Neither chlorpyrifos-methyl nor fenchlorphos were found in the material under study. Chlorpyrifos was the pesticide occurring in the highest levels in the peel of both vegetables (31?ng?·?g^?1 w.w.) and fruit (9.3?ng?·?g^?1 w.w.). The Maximum Residue Level (MRL) for parathion-methyl was exceeded in some samples of zucchini pulp of Spanish origin and in the peel of potato from Poland. But levels of other pesticides in the studied vegetables and fruits were significantly lower than the current MRLs. The assessment of consumer health risk showed a significantly lower Lifetime Average Daily Dose (LADD) of pesticides under this study comparing to the Acceptable Daily Intake (ADI). Moreover, the Hazard Quotient (HQ) was low with a maximum of 3.93?×?10^?2 for vegetables and 4.26?×?10^?3 for fruits. These estimated HQs were within the safe acceptable limits, indicating low risk to human populations from exposure to organophosphorus pesticides in the study area.     

Assay of diazinon pesticides in cucumber juice and in the deep brain cells of a live carp

An electrochemical assay for diazinon pesticides was developed using cyclic voltammetry and square-wave anodic and cathodic stripping voltammetry. The method has a linear working range from 6 to 62 ng L^?1. The detection limit is 0.5 ng L^?1 (1.64 pM), and the relative standard deviation at a diazinon concentration of 6.0 mg L^?1 was 0.06% (n?=?15) in an 0.1 M ammonium phosphate electrolyte solution. The results of the application of the sensor were compared with those of other common spectrometric and electrochemical methods. The method was also applied to cucumber juice and the deep brain cells of a live carp in real conditions.     

Validated dispersive liquid-liquid microextraction for analysis of organophosphorous pesticides in water

Dispersive liquid-liquid microextraction (DLLME) combined with gas chromatography and mass spectrometry (GC-MS) was applied to the determination of six organophosphorous pesticides (OPPs) in water samples. The analytes included in this study were prophos, diazinon, chlorpyrifos methyl, methyl parathion, fenchlorphos and chlorpyrifos. Several extraction and dispersion solvents were tested for dispersive liquid-liquid microextraction of these analytes and the best results were obtained using chloroform as extraction solvent and 2-propanol as dispersion solvent. Calibration curves of the analytes in water samples were constructed in the concentration range from 100 to 1100 ng/L for prophos, diazinon and methyl parathion and in the range from 100 to 1000 ng/L for chlorpyrifos methyl, fenchlorphos and chlorpyrifos. Limits of detection (LODs) were in the range of 1.5-9.1 ng/L and limits of quantification (LOQs) were in the range of 5.1-30.3 ng/L, below the maximum admissible level for drinking water. Relative standard deviations (RSDs) were between 6.5 and 10.1% in the concentration range of 100-1000 ng/L. The relative recoveries (%RRs) of tap, well and irrigation water samples fortified at 800 ng/L were in the range of 46.1-129.4%, with a larger matrix effect being detected in tap water.     

Simultaneous Filtration and Solid-Phase Extraction Combined with Large-Volume Injection in GC/MS for Ultra-Trace Analysis of Polar Pesticides in Surface Water

A method combining simultaneous filtration and solid-phase extraction (SPE) with large-volume injection (LVI) in gas chromatography/mass spectrometry (GC/MS) was developed to determine 13 polar pesticides in surface water. The selected pesticides - 4 organophosphorus, 7 organonitrogens and 2 triazine degradation products - were extracted from 0.5-L samples of filtered and raw water using cartridges filled with a silica-bonded material (1 g of ISOLUTE triazine, C-18) and a depth filter. No obstruction was observed during the extraction of raw water drawn from the St. Lawrence River (concentration of suspended particulate matter (SPM) ranging from 2 to 58 mg L^?1). Overall percent recoveries were satisfactory for all the target pesticides (>60%) except desisopropyl-atrazine (more polar), which varied from 29 to 46% according to sample pH. The coefficient of variation was below 10% for the majority of the target pesticides and detection limits ranged from 0.1 to 0.8 ng L^?1. Applied to real samples drawn from the St. Lawrence River, this method allowed for the detection of atrazine, cyanazine, desethyl-atrazine (DEA), desisopropyl-atrazine (DIA), metolachlor and simazine, at concentrations of 6 to 91 ng L^?1. Using atrazine and metolachlor as examples, the correlation between filtered and raw water samples was more significant for the former (r = 0.87) than for the latter (r = 0.67). Temporal variations in atrazine and metolachlor in filtered water drawn from the St. Lawrence River, for example, were similar whether using the established method, based on liquid-liquid large-volume extraction (LVE) combined with GC/NPD analysis, or the one proposed herein. The latter method, however, systematically found atrazine concentrations 62% higher than those obtained by the older one, applied to the same field samples. Thus, the switch to the new analytical method will require the application of a correction factor to the atrazine concentration time series acquired with the previously used method.     

Evaluation and validation of commercially available enzyme-linked immunosorbent assays (ELISAs) specific for atrazine, chlorpyrifos, and diazinon in aqueous phase

The performance of commercially available microtiter plate enzyme-linked immunosorbent assays (ELISA) kits specific for the determination of triazines (atrazine), chlorpyrifos, and diazinon was evaluated for sensitivity, intra-assay repeatability, and accuracy using samples of known concentration in aqueous solution. Mean percent recovery values were not significantly different among concentrations for diazinon (One-way parametric ANOVA, P=0.46, n=72). However, mean percent recovery values were significantly different among concentrations for both atrazine and chlorpyrifos analyses (One-way parametric ANOVA, P<0.0001, n=36 for both analyses), and were highly dependent on concentrations for chlorpyrifos (% recovery=−0.155 (concentration)+238.448, r²=0.91, P<0.0001, n=36). All methods demonstrated a high degree of statistical separation between readings at various concentrations (One-way parametric ANOVA followed by Student-Neuman-Keuls (SNK) multiple range test, P<0.0001 for all analyses) and a close correlation between known concentrations and concentrations derived from ELISA for all three analytes (diazinon, r=0.985, P<0.0001, n=72; atrazine r=0.967, P<0.0001, n=36; chlorpyrifos r=0.947, P<0.0001, n=36). Statistical comparisons between known concentrations and concentrations derived from ELISAs showed that diazinon values were significantly (P<0.01, n=12 per concentration level) overestimated for all concentration levels. Chlorpyrifos concentrations were significantly (P<0.01, n=6 per concentration level) overestimated at lower concentrations and significantly (P<0.01, n=6 per concentration level) underestimated at higher concentrations. ELISA-derived atrazine concentrations were statistically similar to known concentrations for most concentration levels (P>0.05, n=6 per concentration level). Results indicate that ELISA kits are excellent for screening purposes, although consistent overestimation of ELISA for diazinon at all concentration levels and chlorpyrifos at lower concentrations levels must be resolved before the kits can be used routinely for regulatory compliance monitoring.     

Selection of sampling adsorbents and optimisation and validation of a GC-MS/MS method for airborne pesticides

A methodology for the sampling and determination of airborne pesticides has been developed. The trapping efficiency of three adsorbents, namely XAD-2,XAD-4 and a sandwich sorbent (PUF-XAD2-PUF), was tested for 34 pesticides and the latter was selected because it presented the highest retention capacity without breakthrough. Pesticides were determined by gas chromatography coupled to an ion trap mass spectrometer in tandem. The method showed recoveries ranging from 70% to 120% with limits of quantification in the range of 16.1–322.6 pg m^?3 when 155 m³ were sampled. This analytical strategy was applied to 10 indoor air samples collected in dwellings from the Valencian Region. Six pesticides, namely diphenylamine, pyrimethanil, bifenthrin, lambda-cyhalothrin, permethrin and cypermethrin were detected in indoor samples with concentrations ranging from 1.46 to 22.02 ng m^?3.     

Development of ultrasound-assisted emulsification microextraction for the determination of triazine herbicides in environmental water samples by high-performance liquid chromatography

A simple, rapid, efficient, and environmentally friendly method for the determination of some triazine herbicides (simazine, atrazine, prometone, ametryn and prometryne) in water samples was developed by ultrasound-assisted emulsification microextraction (USAEME) coupled with high-performance liquid chromatography-diode array detection (HPLC-DAD). The main parameters that affect the extraction efficiencies, such as the kind and volume of the extraction solvent, ultrasound emulsification time and salt addition, were investigated and optimized. Under the optimum conditions, the method was sensitive and showed a good linearity within a range of 0.5 to 200?ngm?L^?1 for simazine, atrazine, prometone, ametryn and prometryne, with the correlation coefficients (r) varying from 0.9993 to 0.9998. High enrichment factors were obtained ranging from 148 to 225. The limits of detection (LODs) were in the range between 0.06 and 0.1?ngm?L^?1 and the limits of quantification (LOQs) were in the range between 0.2 and 0.3?ngm?L^?1. The recoveries of the analytes from water samples at spiking levels of 5.0 and 50.0?ngm?L^?1 were ranged from 82.4% to 107.0%. The relative standard deviations (RSDs) varied from 3.0% to 4.6%. The results demonstrated that the USAEME-HPLC-DAD method was an ef?cient pretreatment and enrichment procedure for the determination of triazine pesticides in real water samples.     

Multiresidue Analysis of Pesticides in Water from Rice Cultures by On-line Solid Phase Extraction Followed by LC-DAD

Abstract

An automated on-line solid phase extraction procedure followed by liquid chromatography with diode array detection was investigated for the determination of different classes of pesticides in water samples containing varied amount of humic substances. The different pesticides used were: carbendazin, carbofuran, atrazine, diuron, propanil, molinate, alachlor, parathion-ethyl, diazinon, trifluralin and the degradation products deisopropylatrazine and deethylatrazine. Humic substances extracted from a Brazilian sediment were used from 5 to 80 mg/l and their influence on recoveries was evaluated in neutral and acidic media. Recoveries higher than 70% were obtained for all the pesticides, from the preconcentration of 75 ml of aqueous sample fortified at 2 ng/ml using precolumns packed with PLRP-S. Good recoveries were obtained at neutral pH for most of the analytes up to 40 mg/l of humic acid. Only at 80 mg/l the recoveries were significantly affected, both at acidic and neutral pH. The method was applied to the determination of pesticides in river water spiked at 0.1 to 1 ng/ml. Detection limits obtained for water containing 10 mg/l of humic acid were between 0.05 and 0.3 ng/ml.     

Amperometric Immunoassay of Azinphos‐Methyl in Water and Honeybees Based on Indirect Competitive ELISA

Abstract

An electrochemical immunosensor based on indirect competitive ELISA technique has been developed and tested for the detection of azinphos‐methyl in aqueous solutions and spiked honeybee extracts. The detection of the pesticide was based on competition for binding to monoclonal antibodies with an ovalbumin (OVA) conjugate, followed by the incubation with anti‐mouse IgG labeled with horseradish peroxidase, whose activity was measured amperometrically with hydroquinone as the substrate. The sensitivity of the azinphos‐methyl assay, estimated as the IC₅₀ value, was found to be 1.2 nmol L^?1 (60 min incubation), with a linear range of 0.6–500 nmol L^?1 in optimal conditions. The matrix effect on the detection of azinphos‐methyl in honeybee extract was found negligible, with the recovery values in the range 92–105%.     

QuEChERS Technique for the Gas Chromatographic Determination of Organophosphate Residues in Strawberries

This study describes the validation of an analytical method employing gas chromatography with flame photometric detection for the determination of organophosphate pesticides (diazinon, disulfoton, parathion, chlorpyrifos, and malathion) in strawberries. The method employed a QuEChERS dispersive solid phase extraction for the sample preparation. QuEchERS is inexpensive, fast, and easy for the separation of the analytes from the matrix. In addition, the method provided linear calibration curves, ranging from 0.10–1.00 µg g^?1, for diazinon, disulfoton, parathion, and chlorpyrifos, and 0.10–2.00 µg g^?1 for malathion. Recovery studies yielded values in the range from 81.64 to 100.00%. These results demonstrated the potential of the technique for the determination of organophosphate residues in strawberries.     

Simultaneous Determination of Atrazine and Chlorpyrifos in Pesticide Formulations,in Soils and Waters by Derivative Spectrophotometry and Ratio Spectra Derivative

Abstract

A new method is described to analyse a binary mixture of atrazine and chlorpyrifos, using first-derivative spectrophotometry for atrazine and first derivative of the ratio spectra for chlorpyrifos. The procedure does not require any separation step. Calibration graphs were linear up to 15 μg.mL^?1 of atrazine and to 10 μg.mL^?1 of chlorpyrifos. The method has been applied to determine both compounds in pesticide formulations, in soils and waters.     

Multi-determination of organic pollutants in water by gas chromatography coupled to triple quadrupole mass spectrometry

A multi-determination method has been developed for the determination and confirmation of 68 organic pollutants in water samples by gas chromatography coupled to triple quadrupole mass spectrometry (GC-MS/MS). The following chemical families were determined in a chromatographic run of less than 26?min: polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), polybrominated diphenylethers (PBDEs), and pesticides (organochlorine, organophosphorus, triazine and others). The sample preparation involved a liquid-liquid extraction (LLE) procedure, obtaining recoveries ranging from 70 to 130% when dichloromethane was used as the extracting solvent. The detection limits of the proposed method were between 0.75 and 19.8?ng?L^?1. Samples from the Maipo River in central Chile were taken from 29 different points. Seven pesticides and two PAHs were detected in field collected samples with concentrations ranging from 10 to 95?ngL^?1. Concentrations of benzo[a]pyrene in environmental samples ranged from 25 to 33?ngL^?1 and were near the maximum levels established by the European Union Directives (50?ng?L^?1).     

A modified quick,easy, cheap,effective, rugged,and safe method for determination of by-products originating from ozonation of chlorpyrifos and diazinon spiked in cherry tomato and perilla leaf

In this study, sample pretreatment methods have been developed for the determination of chlorpyrifos, diazinon, and their by-products present in cherry tomato and perilla leaf using liquid chromatography-tandem mass spectrometry. To optimize a quick, easy, cheap, effective, rugged, and safe method, the recoveries at each step were evaluated. The steps improved the recoveries of chlorpyrifos, chlorpyrifos oxon, diazinon, diazoxon, and 2-isopropyl-6-methyl-4-pyrimidinol up to 80% or more by removing interferents, but diethyl phosphate was almost lost during the partition procedure, and the 3,5,6-trichloro-2-pyridinol recovery was below 65%. Therefore, the compounds were evaluated using different solvent compositions based on a quick polar pesticides method; note that 100% methanol showed acceptable extraction results. The optimized method provided method detection limits ranging from 0.03 to 1.22 ng/g and good linearities (R² > 0.996). The recovery values were between 82.1 and 113.3%. The intra- and interday reproducibility was evaluated to be within 8.6 and 9.9%, respectively. The method was applied to determine the degradation efficiency of chlorpyrifos and diazinon and their by-products formed during plasma treatment.     

Validation of a highly sensitive method for the determination of neonicotinoid insecticides residues in honeybees by liquid chromatography with electrospray tandem mass spectrometry

The validation of a multi-residue method for the determination of five neonicotinoid insecticides (imidacloprid, clothianidin, acetamiprid, thiacloprid and thiamethoxam) in honeybees is described. The method involves the extraction of pesticides using acetonitrile and liquid partitioning with n-hexane. One clean-up is then performed on a florisil cartridge (1?g, 6?mL) and the extract is analysed by liquid chromatography-electrospray ionisation-tandem mass spectrometry (LC-ESI-MS/MS). The recovery data were obtained by spiking honeybees samples free of pesticides at two concentration levels of the various neonicotinoids. The recoveries were in the range between 93.3 and 104.0% with relative standard deviation (RSD) less than 20%. The limit of quantification (LOQ) was 0.5?ng?g^?1 (corresponding to 0.05?ng?bee^?1) for all pesticides except for acetamiprid which was 1?ng?g^?1 (corresponding to 0.1?ng?bee^?1).