Spectrophotometric Determination of Uranium(VI) with Chlorophosphonazo-mN by Flow Injection Analysis

Abstract

A sensitive and selective spectrophotometric flow injection analysis (FIA) method with chlorophosphonazo-mN has been developed for the determination of uranium(VI) in standard ore samples. Most of interfering ions are effectively eliminated by the masking reagent of diethylenetriaminepentaacetic acid (DTPA). In the U(VI)-chlorophosphonazo-mN system, the maximum absorption wavelength is at 680 nm and Beer's law is obeyed in the range of 1 to 15 μg ml^?1. The correlation coefficient of the calibration curve is 0.9998, the sampling frenquency is 60 h^?1, and the detection limit for uranium(VI) is 0.5 μg ml^?1. The composition of the U(VI)-chlorophosphonazo-nN complex was established to be 1:2 by flow-through spectrophotometric and conventional molar ratios methods.     

Spectrophotometric determination of uranium in natural waters

A method for the spectrophotometric determination of uranium in samples of natural water is described. Ion exchange with Amberlite IR-120 (H⁺) to concentrate the metal was used. The absorption properties of the complex formed between uranium and the chromogenic reagent Arsenazo III, its stability over several hours, the effect of the pH on the ability of the resin to retain uranium, the reproducibility of the method and the effects of ionic interferences were considered. The sensitivity was 0.67 and 0.05 μg l^?1 of uranium for the direct and the addition methods, respectively. Uranium concentrations for the samples analysed were between 0.10 and 0.50 μg l^?1.     

Spectrophotometric determination of trace uranium in geological samples by flow injection analysis with on-line levextrel resin separation and preconcentration

A flow-injection system with on-line separation and preconcentration is described for the spectrophotometric determination of trace uranium in geological samples. Uranium is selctively adsorbed from 0.7 mol l^?1 nitric acid on a microcolumn (40 mm long, 4.4 mm i.d.) containing levextrel CL-5209 resin (120–200 mesh) and separated from the sample matrix and most of the co-existing ions; 10-fold concentration is obtained. Eluted uranium is determined spectrophotometrically with arsenazo-III. The detection limit is μg l^?1 uranium and calibration is linear up to 0.3 mg l^?1 uranium With dual columns operated alternately for adsorption and elution, 30 samples can be analyzed per hour. Masking agents are added to eliminate interferences from thorium and iron. The method is sensitive and highly selective, easy to operate and suitable for routine analysis of geological samples for uranium.     

Determination of Traces of Vanadium with 5-Bomosalicylhydroxamic Acid by Solid-Phase Spectrophotometry

Abstract

A microdetermination method at μg 1^?1 levels for vanadium by solid-phase spectrophotometry has been developed. 5-Bromosalicylhydroxamic acid was used as chromogenic reagent to form a 1:2 violet complex which is easily sorbed and concentrated on a dextran-type anion-exchange resin. The resin-phase absorbances at 560 and 850 nm were measured directly. Vanadium can be determined in the 5 - 60 μg 1^?1 range with a RSD of 4.3%. The method is applied to the determination of vanadium in pet roleiim crudes and natural water, samples.     

Integrated Retention/Spectrophotometric Detection Method for the Determination of Formaldehyde

Abstract

An integrated-sensor method for the determination of formaldehyde based on retention of the reaction product of the analyte with p-rosaniline and sulfite in a flow-cell packed with Dowex 1-X-8 anion exchange resin was developed. The method has a good selectivity with a detection limit of 0.3 μg ml^?1 (1 ml sample) or 75 ng ml^?1 (2 ml sample), and a linear range between 1–30 μg ml^?1. The relative standard deviations (n = 11) were 2.8 and 1.3% for 2 and 20 μg ml^?1 formaldehyde, respectively. Depending on the working conditions, the sampling frenquency ranged between 10 and 18 h^?1. The method was applied to the determination of formaldehyde in well water.     

Application of High Performance Liquid Chromatography to the Analysis of Nuclear Materials

Abstract

A small-particle (13 μm) styrene-divinylbenzene cation-exchange resin has been used for the separation and determination of trace metals in nuclear materials such as steels, Ni-Cr-Fe alloys, zirconium, and uranium. The eluted metal ions, which included Mn, Fe, Co, Ni, Cu, Zn and Pb, were monitored with a variable wavelength detector after a post-column reaction with 4-(2-pyridylazo)-resorcinol. The metal ions were determined at 10^?4 to 1% (w/w) levels by direct injection of solutions of the materials. Interference from uranium, due to the reaction between uranium and the reagent used for detection, was removed either with a masking agent or by a coupled-column technique.     

Simultaneous Plutonium and Uranium Isotopic Analysis from a Single Resin Bead - A Simplified Chemical Technique for Assaying Spent Reactor Fuels

Abstract

The method uses basic anion resin to adsorb plutonium and uranium from 7–8 M HNO₃ solutions containing dissolved spent reactor fuels. After equilibrating the resin with the solution, a single bead is used to determine the isotopic composition of plutonium and uranium on sample sizes as small as 10^?9 to 10^?10 g of each element per bead. Isotopic measurements are essentially free of isobaric interferences and fission product contamination in the mass spectrometer is eliminated. A very small aliquot of dissolver solution containing 10^?6 g of U and 10^?8 g of Pu is sufficient sample for chemically preparing several resin beads. A single prepared bead is loaded onto a rhenium filament and analyzed in a two-stage mass spectrometer using pulse counting for ion detection to obtain the high sensitivity required. Total quantity of the elements, in addition to isotopic abundances, can be determined by isotope dilution. Other areas where the method may be useful are: in plutonium production, isotope separations, and for trace detection of contamination on reactor parts.     

Synthesis and Application of New Resin Functionalized by Brilliant Green for Spectrophotometric Determination of Mercury in Environmental Samples

Abstract

A new chelating resin was prepared by coupling Amberlite XAD-4 with brilliant green through an azo spacer, and it has been used for preconcentration and separation of mercury(II) in environmental samples prior to its determination by spectrophotometry. The sorption capacity of functionalized resin is 4.12 mg g^?1. Spectrophotometric determination of Hg(II), free from the interference of almost all cations and anions found in the environmental water samples, is a notable advantage of the method. The determination of Hg(II) in wastewater and seawater was carried out by the present method and cold vapor atomic absorption spectrometry (CVAAS).     

Development of method for determination and preconcentration of uranium in water samples using XAD-4 resin loaded with Br-PADAP

In the present work, a minicolumn of XAD-4 loaded with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (Br-PADAP) is proposed as a preconcentration system for uranium determination in well, tap and mineral water samples by spectrophotometer using arsenazo III as the chromogenic reagent. Initially, a two-level (2³) full factorial design was used for the preliminary evaluation of three factors, involving the following variables: sampling flow rate, elution flow rate, and pH. This design has revealed that, for the studied levels, buffer concentration and pH were significant factors. When the experimental conditions established in the optimization step were pH = 8.6, and an elution flow rate of 8.6 mL min^?1 using 0.5% m/v ascorbic acid, this system has allowed for the determination of uranium with a detection limit (LOD) (3σ/S) of 0.05 μg L^?1 and a quantification limit (LOQ) (10σ/S) of 0.16 μg L^?1. The precision expressed as the relative standard deviation (R.S.D.) of 0.8% and 1.9% at 10.0 and 1.0 μg L^?1, respectively- and a preconcentration factor of 184.5 for a sample volume of 50.0 mL. Accuracy was confirmed by uranium determination in the standard reference material, NIST SRM 1566b trace element units in Oyster Tissue samples, and spike tests with recuperations ranging from 93.2 to 105%; the procedure were applied for uranium determination in tap water, well water, and drinking water samples collected from Caetité and Cruz das Almas Cities, Bahia, Brazil. Five water samples were analyzed the uranium concentrations varied from 0.50 to 2.07 μg L^?1     

A method for dating small amounts of uranium

In this study we describe a method for uranium dating (i.e. determination of the date of the last chemical purification undergone by the material) by measurement of the ²³⁰Th/²³⁴U ratio, applicable to sub-microgram quantities. The chosen protocol (AG1x8 resin in hydrochloric acid medium) has been tested on separation microcolumns (100 μl). This ‘microchemistry’ technique considerably limits the risks of contamination by reagents or the environment. Thorium extraction efficiencies were greater than 90 % and reproducible. The quantities of ²³⁰Th introduced by the chemical purification procedure were negligible. Using an ultra-sensitive inductively coupled plasma mass spectrometry measurement technique, detection limits of the order of femtograms (10^?15 g) of ²³⁰Th were obtained. The complete procedure, chemical separation and isotope measurement, was successfully tested and validated on a few micrograms of uranium.     

Determination of uranium in process stream solutions from uranium extraction plant employing energy dispersive X-ray fluorescence spectrometry

Energy dispersive X-Ray fluorescence (EDXRFS) method is developed and standardized for the determination of uranium on routine basis in various process stream solutions, covering a vide range of concentrations from 0.1 to 400?g?L^?1, from an Uranium Extraction Plant at Nuclear Fuel Complex. The method has been applied to aqueous stream samples. Except for dilution, no much sample preparation was involved in the analysis and accordingly the experimental parameters were optimized. The calibration curve in the range of 0.1?C10?g?L^?1 of U was drawn manually using synthetic standard solutions prepared from U₃O₈ powder and L?? (13.61?keV) line of uranium was used for the measurements. The results from EDXRFS method are compared with other methods and are found to be in good agreement. The EDXRFS measurements carried over a range of 0.1?C350?g?L^?1 of uranium have shown a RSD of ±1?C5%. Also, the limitations of reported methods in literature and the advantages of present method are highlighted in the paper.     

Extraction-photometric determination of uranium(IV) with chlorophosphonazo-III

A sensitive spectrophotometric method has been developed for the determination of uranium. The uranium(IV)-chlorophosphonazo-III complex is extracted into 3-methyl-1-butanol from 1.5–3.0 M hydrochloric acid solution. Maximal absorbance occurs at 673 nm and Beer's law is obeyed over the range of 0–15 μg per 10 ml of the organic phase. The molar absorptivity is 12.1·10⁴ 1 mole^?1 cm^?1. Uranium can be determined in the presence of fluoride. sulfate and phosphate. Nitrate ion and elements (chromium, copper, iron) which affect the reduction of uranium(VI) or stability of uranium(IV) interfere.     

Flow-injection chemiluminescence determinations for human blood lead using controlled reagent release technology

A flow-through CL method for the determination of lead combined with controlled-reagent-release technology has been developed. Chemiluminescence (CL) reagents luminol and potassium permanganate were immobilized on anion exchange resin by electrostatic interaction. Lead ion was determined by its enhancing effect on the CL reaction between luminol and potassium permanganate. Both luminol and potassium permanganate were eluted from the anion exchange resin column by sodium phosphate solution. The linear range of the system was 10 μg mL^?1, and the detection limit was 5?×?10^–9 g mL^?1 lead (3σ). A complete analysis could be performed in 1 min with a relative SD 3.2% (1.0?×?10^–7 g mL^?1, n?=?9). The column shows remarkable stability and can be reused over 350 times and 21 days. The method has been applied to determine lead in human blood samples.     

A New Spectrophotometric Method for the Determination of Maneb in Commercial Formulations

Abstract

A new rapid, selective and sensitive method has been developed for the determination of maneb using pyrocatechol-violet(PV) as chelating reagent in the pH range of 7.5–11.0 in the presence of CTAB producing a complex which shows maximum absorption at 640 nm. Working range of the method is 0.2–3.0 μg ml^?1 maneb (manganese ethylenebisdithiocarbamate). The molar absorptivity of the color system is 79600 1 mol^?1 cm^?1 and Sandell's sensitivity is 0.0033 μg cm^?2. The reproducibility of the method has been checked by the 10 replicate analysis of 15 μg of maneb in 10 ml of solution. The method is quite sensitive and has been applied for the determination of maneb in various commercial samples, crops, grains and synthetic samples.     

Spectrophotometric Determination of Iron In Wines,Vegetables, Pharmaceutical Compounds and Minerals With Mandelohydroxamic Acid (Mha)

Abstract

A new reagent, mandelohydroxamic acid (MHA), which has an easy synthesis and an high water solubility (64.48 gL^?1) is proposed for a simple, rapid, selective and sensitive method for the spectrophotometric determination of iron based upon the formation of the MHA-Fe(III) complex and its extraction into n-butanol under optimum operating conditions. A yellow color is formed when the complex is extracted from acidic aqueous medium (Vw/Vo[dbnd]5) in the organic solvent (apparent molar absortivity 1.15 10⁴ L mol^?1 cm^?1 at a wavenlength of 430 nm). the relative error is 0.5% (2 ppm of iron) and the detection limit is 0.05 g mL^?1 of Fe(III). the method has been applied to the determination of iron in wines, vegetables, pharmaceutical compounds and minerals.     

Direct and Second Order Analogue Derivative Extraction-Spectrophotometric Determination of Iron with 2 (4, 5-Dimethyl-2-Thiazolylazo)-4, 6-Dimethylphenol

Abstract

An extraction-spectrophotometric method for the determination of trace amounts of iron based on its extraction into chloroform with 2-(4, 5-dimethyl-2-thiazolylazo)-4, 6-dimethylphenol has been developed, which allows the determination of 5–28 μg Fe (?₇₇₃ = 1.38×10⁴ 1. mol^?1. cm^?1). The use of second order analogue derivative spectrophotometry allows the determination of down to 0.2–5 μg, Fe. The methods are quite selective and have been applied to the determination of iron in mineral waters.     

An Improved Solid Phase Spectrophotometry Method for the Determination of Aromatic Esters

Abstract

A method based on Solid Phase Spectrophotometry was developed for the determination of methyl benzoate. Hydroxamic acid formed by the reaction between the above and hydroxylamine, reacts with V(V) and oxalate yielding a violet compound, which is sorbed on an anion-exchange resin. The absorbance of the resin phase at 546 and 750 nm is measured directly. The calibration graph is linear for the 4.8–23 μM concentration range. RSD is shown as 3.7%, with a detection limit of 0.09 mg. 1^?1. This method has been applied to the determination of aromatic esters in brandies.     

Amberlite XAD-4 functionalized with succinic acid for the solid phase extractive preconcentration and separation of uranium(VI)

Amberlite XAD-4 resin has been functionalized with succinic acid by coupling it with dibromosuccinic acid after acetylation. The resulting resin has been characterized by FT-IR, elemental analysis and TGA and has been used for preconcentrative separation of uranium(VI) from host of other inorganic species prior to its determination by spectrophotometry. The optimum pH value for quantitative sorption of uranium(VI) in both batch and column modes is 4.5-8.0 and desorption can be achieved by using 5.0 ml of 1.0 mol l⁻¹ HCl. The sorption capacity of functionalized resin is 12.3 mg g⁻¹. Calibration graphs were rectilinear over the uranium(VI) concentrations in the range 5-200 μg l⁻¹. Five replicate determinations of 50 μg of uranium(VI) present in 1000 ml of solution gave a mean absorbance of 0.10 with a relative standard deviation of 2.56%. The detection limit corresponding to three times the standard deviation of the blank was found to be 2 μg l⁻¹. Various cationic and anionic species at 200-fold amounts do not interfere during the preconcentration of 5.0 μg of uranium(VI) present in 1000 ml (batch) or 100 ml (column) of sample solution. Further, adsorption kinetic and isotherm studies were also carried out by a batch method to understand the nature of sorption of uranium(VI) with the succinic acid functionalized resin. The accuracy of the developed solid phase extractive preconcentration method in conjunction with Arsenazo III procedure was tested by analyzing marine sediment (MESS-3) and soil (IAEA soil-7) reference material. Further, the above procedure has been successfully employed for the analysis of soil and sediment samples.     

The Determination of Manganese by Means of Tetrazolium Violet

Abstract

The optimum conditions for extraction of manganese (VII) as an ion-association complex with Tetrazolium Violet (TV) has been determined. The ratio MnO₄ ^?: TV⁺ is 1:1. Beer's law is obeyed in the range of 0.05 - 0.6 μg ml^?1 manganese (VII). The molar absorptivity of the ion-pair is (6.67 ± 0.05) × 10⁴ L mol^?1cm^?1, extraction constant K_ex = 3.1 × 10⁴, distribution constant K_D = 56.5 and association constant β = 5.59 × 10². A sensitive and selective method for determination of microquantities of manganese (VII) in soils has been developed.     

Preconcentration of cobalt using Amberlyst 36 as a solid-phase extractor and its determination in various environmental samples by flame atomic absorption spectrometry

A new and simple column-solid-phase extraction method has been developed to separate and preconcentrate trace cobalt in water and soil prior to its determination by flame atomic absorption spectrometry (FAAS). Different factors such as pH of sample solution, sample volume, amount of resin, flow rate of aqueous solution, volume and concentration of eluent, and matrix effects for preconcentration were optimized. Under optimized experimentally established conditions, an analytical detection limit of 0.44?µg?L^?1, precision (RSD) of 1.9%, enrichment factor of 200, and capacity of resin of 82?mg?g^?1 were obtained. The method was applied for cobalt determination by FAAS in tap water, natural drinking water, soil, and roadside dust samples. The accuracy of the method is confirmed by analysing standard reference material (Montana Soil, SRM 2711).