Dynamic Mechanical Analysis and Molecular Mobility of the R-BAPB Type Polyimide

Summary: Dynamic mechanical experiments are performed to study molecular mobility of the R-BAPB type polyimide based on 1,3-bis-(3,3′,4,4′-dicarboxyphenoxy)benzene (R) and 4,4′-bis-(4-aminophenoxy)biphenyl (BAPB) with a molecular weight M_w ∼ 80 000 g/mol. Frequency dependences of the storage and the loss tensile moduli are measured within the temperature domain 199°C ≤ T ≤ 211°C that includes the glass transition temperature of the compound, T_g = 206°C. It is shown that the time-temperature superposition principle holds for the R-BAPB type polyimide. A theoretical analysis of the master curves constructed at T_ref = 204°C is performed on the basis of the piecewise-power-type distribution function of the relaxation times. Relaxation times for typical scales of motion inside polyimide macromolecules are calculated and the molecular weights of the characteristic kinetic units (the Kuhn segment and the chain fragment between entanglements) are estimated.     

Dynamic light scattering studies of atactic and syndiotactic poly(methyl methacrylate)s in dilute theta solution

The present article considers the coil‐to‐globule transition behavior of atactic and syndiotactic poly(methyl methacrylates), (PMMA) in their theta solvent, n‐butyl chloride (nBuCl). Changes in Rh in these polymers with temperature in dilute theta solutions were investigated by dynamic light scattering. The hydrodynamic size of atactic PMMA (a‐PMMA‐1) in nBuCl (M_w: 2.55 × 10⁶ g/mol) decreases to 61% of that in the unperturbed state at 13.0°C. Atactic PMMA (a‐PMMA‐2) with higher molecular weight (M_w: 3.3 × 10⁶ g/mol) shows higher contraction in the same theta solvent (α_η = R_h(T)/R_h (θ) = 0.44) at a lower temperature, 7.25°C. Although syndiotactic PMMA (s‐PMMA) has lower molecular weight than that of atactic samples (M_w: 1.2 × 10⁶), a comparable chain collapse was observed (α_η = 0.63) at 9.0°C. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2253–2260, 1999     

Self-bonding in an amorphous polymer below the glass transition: A T-peel test investigation

Films of amorphous polystyrene (PS) with a weight-average molecular weight (M_w) of 225 × 10³ g/mol were bonded in a T-peel test geometry, and the fracture energy (G) of a PS/PS interface was measured at the ambient temperature as a function of the healing time (t_h) and healing temperature (T_h). G was found to develop with (t_h)^1/2 at T_h = T_g-bulk − 33 °C (where T_g-bulk is the glass-transition temperature of the bulk sample), and log G was found to develop with 1/T_h at T_g-bulk − 43 °C ≤ T_h ≤ T_g-bulk − 23 °C. The smallest measured value of G = 1.4 J/m² was at least one order of magnitude larger than the work of adhesion required to reversibly separate the PS surfaces. These three observations indicated that the development of G at the PS/PS interface in the temperature range investigated (<T_g-bulk) was controlled by the diffusion of chain segments feasible above the glass-transition temperature of the interfacial layer, in agreement with our previous findings for fracture stress development at several polymer/polymer interfaces well below T_g-bulk. Close values of G = 8–9 J/m² were measured for the symmetric interfaces of polydisperse PS [M_w = 225 × 10³, weight-average molecular weight/number-average molecular weight (M_w/M_n) = 3] and monodisperse PS (M_w = 200 × 10³, M_w/M_n = 1.04) after healing at T_h = T_g-bulk − 33 °C for 24 h. This implies that the self-bonding of high-molecular-weight PS at such relatively low temperatures is not governed by polydispersity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1861–1867, 2004     

Synthesis of poly(p‐phenylene) macromonomers and multiblock copolymers

Rigid‐rod poly(4′‐methyl‐2,5‐benzophenone) macromonomers were synthesized by Ni(0) catalytic coupling of 2,5‐dichloro‐4′‐methylbenzophenone and end‐capping agent 4‐chloro‐4′‐fluorobenzophenone. The macromonomers produced were labile to nucleophilic aromatic substitution. The molecular weight of poly(4′‐methyl‐2,5‐benzophenone) was controlled by varying the amount of the end‐capping agent in the reaction mixture. Glass‐transition temperatures of the macromonomers increased with increasing molecular weight and ranged from 117 to 213 °C. Substitution of the macromonomer end groups was determined to be nearly quantitative by ¹H NMR and gel permeation chromatography. The polymerization of a poly(4′‐methyl‐2,5‐benzophenone) macromonomer [number‐average molecular weight (M_n) = 1.90 × 10³ g/mol; polydispersity (M_w)/M_n = 2.04] with hydroxy end‐capped bisphenol A polyaryletherketone (M_n = 4.50 × 10³ g/mol; M_w/M_n = 1.92) afforded an alternating multiblock copolymer (M_n = 1.95 × 10⁴ g/mol; M_w/M_n = 6.02) that formed flexible, transparent films that could be creased without cracking. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3505–3512, 2001     

Synthesis of star‐shaped polystyrenes via nitroxide‐mediated stable free‐radical polymerization

High molecular weight star‐shaped polystyrenes were prepared via the coupling of 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO) terminated polystyrene oligomers with divinylbenzene (DVB) in m‐xylene at 138 °C. The optimum ratio of the coupling solvent (m‐xylene) to divinylbenzene was determined to be 9 to 1 based on volume. Linear polystyrene oligomers (M_n = 19,300 g/mol, M_w/M_n = 1.10) were prepared in bulk styrene using benzoyl peroxide in the presence of TEMPO at approximately 130 °C under an inert atmosphere. Coupling of the TEMPO‐terminated oligomers under optimum conditions resulted in a product with a number average molecular weight exceeding 300,000 g/mol (M_w/M_n = 3.03) after 24 h, suggesting the formation of relatively well‐defined star‐shaped polymers. Additionally, the intrinsic viscosities of the star‐shaped products were lower than calculated values for linear analogs of equivalent molecular weight, which further supported the formation of a star‐shaped architecture. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 216–223, 2001     

Controlled/living polymerization of methacrylamide in aqueous media via the RAFT process

The polymerization of methacrylamide (MAM) was performed in aqueous media via reversible addition fragmentation chain transfer (RAFT) polymerization with the dithiobenzoate chain‐transfer agent (CTA) 4‐cyanopentanoic acid dithiobenzoate (CTP) and 4,4′‐azobis(4‐cyanopentanoic acid) (V‐501) as initiator. The polymerization in unbuffered water at 70 °C with a CTP/V‐501 ratio of 1.5 was controlled for the first 3 h, after which the molecular weight distribution broadened and a substantial deviation of the experimental from the theoretical molecular weight occurred, presumably because of a loss of CTA functionality at longer polymerization times. Conducting the polymerization in an acidic buffer afforded a well‐defined homopolymer (M_n = 23,800 g/mol, M_w/M_n = 1.08). To demonstrate the controlled/living nature of the system, a block copolymer of MAM and acrylamide was successfully prepared (M_n = 33,800 g/mol, M_w/M_n = 1.25) from a polymethacrylamide macro‐CTA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3141–3152, 2005     

Synthesis and characterization of crystallizable aliphatic thermoplastic poly(ester urethane) elastomers through a non-isocyanate route

A simple non-isocyanate route is developed for synthesizing crystallizable aliphatic thermoplastic poly(ester urethane) elastomers(TPEURs) with good thermal and mechanical properties. Three prepolymers of1,6-bis(hydroxyethyloxycarbonylamino) hexane(BHCH), i.e. Pre PBHCHs, were prepared through the self-transurethane polycondensation of BHCH. A poly(butylene adipate) prepolymer(Pre PBA) with terminal HO― groups was prepared and used as a polyester glycol. A series of TPEURs were prepared by the co-polycondensation of the Pre PBHCHs with Pre PBA at 170 ℃ under a reduced pressure of 399 Pa. The TPEURs were characterized by gel permeation chromatography, FTIR,1H-NMR, differential scanning calorimetry, thermogravimetric analysis, wide-angle X-ray diffraction, atomic force microscopy, and tensile test. The TPEURs exhibited M_n up to 23300 g/mol, M_w up to 51100 g/mol, Tg ranging from-33.8 ℃ to-3.1 ℃, T_m from 94.3 ℃ to 111.9 ℃, initial decomposition temperature over 274.7 ℃, tensile strength up to18.8 MPa with a strain at break of 450.0%, and resilience up to 77.5%. TPU elastomers with good crystallization and mechanical properties were obtained through a non-isocyanate route.     

Phase separation induced by shear quenching in polymer blends with a diblock copolymer

The effects of adding A–B diblock copolymer to a polymer blend (A/B) on phase‐separation kinetics and morphology have been investigated in a fixed shallow‐quench condition (ΔT = 1.5 °C) by in situ time‐resolved light scattering and phase‐contrast optical microscopy. A shear‐quench technique was used in this study instead of a conventional temperature‐quench method. Mixtures of nearly monodisperse low relative‐molecular masses of polybutadiene (M_w = 2.8 kg/mol), polystyrene (M_w = 2.6 kg/mol), and a near‐symmetric butadiene–styrene diblock copolymer (M_w = 6.3 kg/mol) as an interfacial modifier were studied. We observed that the addition of the diblock copolymer could either retard or accelerate the phase‐separation kinetics depending on the concentration of the diblock copolymer in the homopolymer blends. In contrast to the conventional temperature quench, we observed complex phase‐separation kinetics in the intermediate and late stages of phase separation by the shear‐quench technique. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 819–830, 2001     

Living anionic ring-opening polymerization of 1,1-dipropylsilacyclobutane

Synthesis and living anionic ring-opening polymerization of 1,1-dipropylsilacyclobutane are reported. High molecular weight poly(dipropylsilylenepropylene) up to M _n = 83900 g/mol (SEC/PS standards) with low polydispersity (M _w/M _n = 1.11 to 1.22) was obtained at −20°C. End functionalization of poly-(dipropylsilylenepropylene) with chlorodimethylvinylsilane and synthesis of block copolymers with styrene was achieved. The polymers were characterized with NMR, SEC, MALDI-TOF and DSC.     

Surface mobility and diffusion at interfaces of polystyrene in the vicinity of the glass transition

Symmetric polydisperse (M_w = 23 × 10⁴, M_w/M_n = 2.84) and monodisperse (M_w = 21 × 10⁴, M_w/M_n < 1.05) polystyrene (PS), and asymmetric polydisperse PS/poly(2,6-dimethyl 1,4-phenylene oxide) (PPO) interfaces have been bonded in the vicinity of the glass transition temperature (T_g) of PS. In a lap-shear joint geometry, strength develops in all cases with time to the fourth power, which indicates that it is diffusion controlled. Strength developing at short times at the polydisperse PS/PS interface, at 90°C, is higher than that at the monodisperse interface, at 92°C (at T_g − 13°C in both cases), presumably due to the contribution of the low molecular weight species. The decrease of strength at the PS/PPO interface when the bonding temperature decreases from 113 to 70°C, i.e., from T_g + 10°C to T_g − 33°C of the bulk PS, indicates a high molecular mobility at the surface as compared to that in the bulk, and can be expressed by a classical diffusion equation, which is valid above T_g (of the surface layer). © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 567–572, 1998     

Liquid-liquid phase equilibria for some polystyrene-methylcyclohexane mixtures

Liquid-liquid cloud point diagrams of solutions of nearly monodisperse samples of polystyrene (PS), and binary mixtures of nearly monodisperse PS’s, both in methylcyclohexane (MCH), were determined for several polymer molecular weights (M_w) at 0.1 MPa. The bimodal mixtures (PS[M_w(1),ρ(1)] + PS[M_w(2),ρ(2)], M_w(1)=90×10³ g/mol, M_w(2)=13×10³ g/mol, 5.78 × 10³ g/mol, and 2.2 × 10³ g/mol, ρ=1.06) were prepared constraining 〈M_w〉=38.6×10³ g/mol, ρ=M_w/M_n is the polydispersity index. In each case the cloud point curves (CPC’s) for the bimodal mixtures are strongly skewed, lying well above CPC for 〈M_w〉 when φ<φ_CRITICAL, and below CPC for 〈M_w〉 when φ>φ_CRITICAL; φ is volume fraction polymer in the polymer/solvent mixture. The experimental results are discussed in the context of empirical and mean-field representations.     

New insights into the effects of molecular weight and end group on the temperature-induced phase transition of poly(N-isopropylacrylamide) in water

In an attempt to clarify issues related to the molecular weight dependence of the phase transition of poly(N-isopropylacrylamide) (PNIPAM) in water,we prepared a library of PNIPAM samples of well-controlled molecular weight (7000 to 45000 g/mol) bearing identical groups on each chain end.The polymers were synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization of N-isopropylacrylamide (NIPAM) with a bifunctional chain tranfer agent and further end group modification.The effects of the end group chemical structure,hydroxyethyl (HE),propargyl (Pr),chloroethyl (CE),n-butyl (nBu),n-hexyl (nHe),and isobutylsulfanylthiosulfanyl (IBS) on the phase transition temperature of aqueous PNIPAM solutions were investigated by high-sensitivity differential scanning calorimetry (HS-DSC),yielding the enthalpy ΔH and the endotherm maximum temperature (T M),and turbidimetry,providing the cloud point (T CP) of each solution.The T CP and T M of the PNIPAM sample of lowest molar mass (M n 7,000 g/mol,0.5 g/L) ranged,respectively,from 38.8 to 22.5 °C and 42.2 to 26.0 °C,depending on the structure of the end-group,whereas H showed no strong end-group dependence.The phase transition of all polymers,except,-di(n-butyl-PNIPAM),exhibited a marked dependence on the polymer molar mass.     

Melt‐processable thermosetting polyimide: Synthesis,characterization, fusibility,and property

To obtain a melt‐processable thermosetting polyimide having a high glass‐transition temperature (T_g) and good solvent resistance, the effect of introducing a crosslinkable agent into the polymer chain ends of the melt‐processable polyimide on its physical properties was studied. The polyimide (calculated number‐average molecular weight (M_n) = 11,600 g/mol) capped with the crosslinkable agent exhibited poor melt flowability because its crosslinkable agent reacted at the processing temperature of 360 °C. To reduce the rate of crosslink reaction, two methods were investigated. One was lowering the processing temperature, and the other was decreasing the amount of crosslinkable agent. The low‐molecular‐weight oligomer (calculated M_n = 6300 g/mol) capped with the crosslinkable agent exhibited good melt flowability at the lower processing temperature of 340 °C where the crosslinkable agent did not react. However, the obtained molded part of this oligomer was too brittle to maintain its shape. However, the polyimide (calculated M_n = 11,600 g/mol) partially capped with the crosslinkable agent demonstrated good melt flowability at the processing temperature of 360 °C. Furthermore, the molded part of this resin was strong and tough. In addition, the cured part exhibited high T_g and good solvent resistance. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2395–2404, 2004     

Evaluation of Enhanced Thermostability and Operational Stability of Carbonic Anhydrase from Micrococcus Species

Carbonic anhydrase (CA) was purified from Micrococcus lylae and Micrococcus luteus with 49.90 and 53.8 % yield, respectively, isolated from calcium carbonate kilns. CA from M. lylae retained 80 % stability in the pH and temperature range of 6.0–8.0 and 35–45 °C, respectively. However, CA from M. luteus was stable in the pH and temperature range of 7.5–10.0 and 35–55 °C, respectively. Cross-linked enzyme aggregates (CLEAs) raised the transition temperature of M. lylae and M. luteus CA up to 67.5 and 74.0 °C, while the operational stability (T _1/2) of CA at 55 °C was calculated to be 7.7 and 12.0 h, respectively. CA from both the strains was found to be monomeric in nature with subunit molecular weight and molecular mass of 29 kDa. Ethoxozolamide was identified as the most potent inhibitor based on both IC₅₀ values and inhibitory constant measurement (K _i). The K _m and V _max for M. lylae CA (2.31 mM; 769.23 μmol/mg/min) and M. luteus CA (2.0 mM; 1,000 μmol/mg/min) were calculated from Lineweaver–Burk plots in terms of esterase activity. Enhanced thermostability of CLEAs alleviates its role in operational stability for application at an on-site scrubber. The characteristic profile of purified CA from Micrococcus spp. advocates its effective application in biomimetic CO₂ sequestration.     

Effect of temperature and water as additive on the MW and thermal properties of copoly(p-phenylene/biphenylene sulfide)s

Copoly(p-phenylene/biphenylene sulfide)s, PPBS were prepared from sodium sulfide trihydate(Na₂S·3H₂O), p-dichlorobenzene (DCB), and 4,4′-dibromobiphenyl (DBB) comonomers in N-methyl-2-pyrrolidinone (NMP) solvent using an autoclave. The molecular weights of PPBS copolymers were determined by high temperature (210°C) GPC in 1-chloronaphthalene solvent. The reaction temperature had little effect on the molecular weights of PPBS copolymers with water as additive at the level of 3 mol H₂O per 1 mol Na₂S. PPBS copolymer, however, showed maximum molecular weight of M_w = 24.1 × 10³ with the total water content of 9 mol H₂O per 1 mol Na₂S at an optimum polymerization temperature of 270°C. The resulting PPBS copolymer sample showed higher T_g (by 30°C) and lower T_m (by 10°C) than PPS homopolymer prepared under similar conditions. © 1996 John Wiley & Sons, Inc.     

Diffusion and phase behavior of a hydroxypropylcellulose-poly(ethylene glycol) system

The solubility and interdiffusion between hydroxypropylcellulose samples of various molecular masses (M _w = 8 × 10⁴, 14 × 10⁴, 37 × 10⁴, 85 × 10⁴, and 115 × 10⁴) and poly(ethylene glycol) (M _w = 400 and 1500) in the range 18–210°C have been studied by optical interferometry and polarization microscopy methods. Oligomeric poly(ethylene glycols) have been considered as solvents for hydroxypropylcellulose. Phase diagrams have been constructed, and Flory-Huggins thermodynamic interaction parameters have been calculated. For the hydroxypropylcellulose-poly(ethylene glycol) 400 system, an LC and crystalline equilibria have been realized. An increase in the M _w of hydroxypropylcellulose to 1500 leads to the appearance of a wide region of amorphous phase segregation with a UCST, whereas the liquidus line is conserved at high concentrations of hydroxypropylcellulose. Such a superposition of two kinds of phase equilibrium that is achieved only with a change in M _w of the oligomeric solvent has been observed for the first time. For all the systems under examination, the kinetics of diffusion mixing has been estimated and the activation energies of the process have been calculated. The concentration dependences of diffusion coefficients demonstrate jumps in the mesomorphic-transition region.     

Microwave‐improved polymerization of ϵ‐caprolactone initiated by carboxylic acids

The ring‐opening polymerization of ε‐caprolactone (ε‐CL), initiated by carboxylic acids such as benzoic acid and chlorinated acetic acids under microwave irradiation, was investigated; with this method, no metal catalyst was necessary. The product was characterized as poly(ε‐caprolactone) (PCL) by ¹H NMR spectroscopy, Fourier transform infrared spectroscopy, ultraviolet spectroscopy, and gel permeation chromatography. The polymerization was significantly improved under microwave irradiation. The weight‐average molecular weight (M_w) of PCL reached 44,800 g/mol, with a polydispersity index [weight‐average molecular weight/number‐average molecular weight (M_w/M_n)] of 1.6, when a mixture of ε‐CL and benzoic acid (25/1 molar ratio) was irradiated at 680 W for 240 min, whereas PCL with M_w = 12,100 and M_w/M_n = 4.2 was obtained from the same mixture by a conventional heating method at 210 °C for 240 min. A degradation of the resultant PCL was observed during microwave polymerization with chlorinated acetic acids as initiators, and this induced a decrease in M_w of PCL. However, the degradation was hindered by benzoic acid at low concentrations. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 13–21, 2003     

Polymer grafting onto polyurethane backbone via Diels–Alder reaction

The aliphatic polyurethane with pendant anthracene moieties (PU‐anthracene) was prepared from polycondensation of anthracen‐9‐yl methyl 3‐hydroxy‐2‐(hydroxymethyl)‐2‐methylpropanoate (anthracene diol), 1 with hexamethylenediisocyanate in the presence of dibutyltindilaurate in CH₂Cl₂ at room temperature for 10 days. Thereafter, the PU‐anthracene (M_n,GPC = 12,900 g/mol, M_w/M_n = 1.87, relative to PS standards) was clicked with a linear α‐furan protected‐maleimide terminated‐poly(methyl methacrylate) (PMMA‐MI) (M_n,GPC = 2500 g/mol, M_w/M_n = 1.33), or ‐poly(ethylene glycol) (PEG‐MI) (M_n,GPC = 550 g/mol, M_w/M_n = 1.09), to result in well‐defined PU‐graft copolymers, PU‐g‐PMMA (M_n,GPC = 23800 g/mol, M_w/M_n = 1.65, relative to PS standards) or PU‐g‐PEG (M_n,GPC = 11,600 g/mol, M_w/M_n = 1.45, relative to PS standards) using Diels–Alder reaction in dioxane/toluene at 105 °C. The Diels–Alder grafting efficiencies were found to be over 93–99% using UV spectroscopy. Moreover, the structural analyses and the thermal transitions of all copolymers were determined via ¹H NMR and DSC, respectively. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 521–527     

Highly stereospecific polymerization of isoprene with homogeneous binary Ziegler-Natta catalysts based on NCN-pincer neodymium precursor

The aryldiimine NCN-pincer stabilized neodymium dichloride combined with aluminum alkyls established a new type of homogeneous binary neutral Ziegler-Natta catalyst system. This system exhibited high activity and high cis-1,4 selectivity for the polymerization of isoprene (T _p = 20 °C, 98.2%; T _p = ?20 °C, > 99%). Such catalytic performances remained under a broad range of polymerization temperatures and monomer-to-neodymium ratios (from 500 to 8000), reaching high number-average molecular weight (M _n = 1582 kg/mol) and relatively narrow molecular weight distribution (PDI = 1.68), which was, however, influenced by the amount and bulkiness of aluminum alkyls. Dynamic investigation of the polymerization was performed, which showed the number-average molecular weight of the resultant polyisoprene had an almost linear correlation with the conversion, suggesting, in some degree, the polymerization with this catalytic system was controllable.     

Synthesis of arborescent polystyrene by “click” grafting

A method was developed for the synthesis of arborescent polystyrene by “click” coupling. Acetylene functionalities were introduced on linear polystyrene (M_n = 5300 g/mol, M_w/M_n = 1.05) by acetylation and reaction with potassium hydroxide, 18‐crown‐6 and propargyl bromide in toluene. Polymerization of styrene with 6‐tert‐butyldimethylsiloxyhexyllithium yielded polystyrene (M_n = 5200 g/mol, M_w/M_n = 1.09) with a protected hydroxyl chain end. Deprotection, followed by conversions to tosyl and azide functionalities, provided the side chain material. Coupling with CuBr and N,N,N′,N″,N″‐pentamethyldiethylenetriamine proceeded in up to 94% yield. Repetition of the grafting cycles led to well‐defined (M_w/M_n ≤ 1.1) polymers of generations G1 and G2 in 84% and 60% yield, respectively, with M_n and branching functionalities reaching 2.8 × 10⁶ g/mol and 460, respectively, for the G2 polymer. Coupling longer (M_n = 45,000 g/mol) side chains with acetylene‐functionalized substrates was also examined. For a linear substrate, a G0 polymer with M_n = 4.6 × 10⁵ g/mol and M_w/M_n = 1.10 was obtained in 87% yield; coupling with the G0 (M_n = 52,000 g/mol) substrate produced a G1 polymer (M_n = 1.4×10⁶ g/mol, M_w/M_n = 1.38) in 28% yield. The complementary approach using azide‐functionalized substrates and acetylene‐terminated side chains was also investigated, but proceeded in lower yield. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1730–1740