Room temperature ionic liquid as a novel medium for liquid/liquid extraction of metal ions

Room temperature ionic liquids (RTILs) have been used as novel solvents to replace traditional volatile organic solvents in organic synthesis, solvent extraction, and electrochemistry. The hydrophobic character and water immiscibility of certain ionic liquids allow their use in solvent extraction of hydrophobic compounds. In this work, a typical room temperature ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate [C₄mim][PF₆], was used as an alternative solvent to study liquid/liquid extraction of heavy metal ions. Dithizone was employed as a metal chelator to form neutral metal-dithizone complexes with heavy metal ions to extract metal ions from aqueous solution into [C₄mim][PF₆]. This extraction is possible due to the high distribution ratios of the metal complexes between [C₄mim][PF₆] and aqueous phase. Since the distribution ratios of metal dithiozonates between [C₄mim][PF₆] and aqueous phase are strongly pH dependent, the extraction efficiencies of metal complexes can be manipulated by tailoring the pH value of the extraction system. Hence, the extraction, separation, and preconcentraction of heavy metal ions with the biphasic system of [C₄mim][PF₆] and aqueous phase can be achieved by controlling the pH value of the extraction system. Preliminary results indicate that the use of [C₄mim][PF₆] as an alternate solvent to replace traditional organic solvents in liquid/liquid extraction of heavy metal ions is very promising.     

Deep eutectic solvents as green media for efficient extraction of terpene trilactones from Ginkgo biloba leaves

Deep eutectic solvents (DESs)-based ultrasonic extraction of terpene trilactones (TTLs) from Ginkgo biloba leaves was efficiently developed. Sixteen DESs were prepared, and DESs composed of choline chloride-urea (ChCl-U) and betaine-ethylene glycol (BE-EG) gave higher TTL extraction yields than the present, most efficient solvent 70% ethanol. The extraction conditions were further optimized, and the optimum conditions were as follows: taking BE-EG containing 40% (w/w) water as the extraction solvent, 1:10 of G. biloba leaves powder-to-solvent ratio, and ultrasonic treatment at 45°C and 100?W for 20?min. A total extraction yield of 1.94?±?0.03?mg/g was obtained under the optimum conditions, which indicated that 99.37% of TTLs could be extracted from the G. biloba leaves powder by a single extraction. Moreover, the polyamide resin was used to recover the TTLs in DES extracting solution, and recovery yield of 95.1% was attained. Therefore, BE-EG containing 40% (w/w) water was a potential alternative solvent for TTLs extraction from G. biloba leaves.     

Limonene as an agro-chemical building block for the synthesis and extraction of bioactive compounds

The objective of this study was to transform limonene as an agro-chemical platform for the production of a wide range of added-value compounds for pharmaceutical, cosmetic and food ingredients. This molecule was also evaluated as an alternative solvent for the extraction of several bioactive compounds compared to n-hexane. Limonene was extracted from the essential oils of orange peels through a solvent-free microwave extraction technique. Limonene was successfully transformed into products with industrial interest by catalytic oxidation using three different iron catalysts. The ability of limonene to be used as an alternative solvent was performed using two simulation tools, Hansen solubility parameters (HSPs) and the Conductor-like Screening Model for Real Solvents (COSMO-RS), and via experimentation. The results indicated that limonene could be a promising green solvent and synthon for petroleum substitution in the extraction or synthesis of bioactive compounds.     

Studies on Liquid/liquid Extraction of Copper Ion with Room Temperature Ionic Liquid

Room temperature ionic liquids are regarded as “Green solvents” for their nonvolatile and thermally stable properties. They are employed to replace traditional volatile organic solvents in organic synthesis, solvent extraction, and electrochemistry. In this work, a water immiscible room temperature ionic liquid, 1‐butyl‐3‐methylimidazolium hexafluorophosphate [C₄mim][PF₆], was used as an alternative solvent for liquid/liquid extraction of copper ions. Metal chelators, including dithizone, 8‐hydroxyquinoline, and 1‐(2‐pyridylazo)‐2‐naphthol, were employed to form neutral metal‐chelate complexes with copper ions so that copper ions were extracted from aqueous solution into [C₄mim][PF₆]. The parameters that affect the extraction of copper ions with this biphasic system were investigated. The extraction behavior in this novel biphasic system is shown to be consistent with that of traditional solvents. For example, the extraction with this biphasic system is strongly pH dependent. So, the extraction efficiency of coppers ion from an aqueous phase can be manipulated by tailoring the pH value of the extraction system. Hence, the extraction, separation and preconcentraction of copper ions can be accomplished by controlling the pH value of the extraction system. It appears that the use of ionic liquid as an alternate solvent system in liquid/liquid extraction of copper ions is very promising.     

Effect of Ionic Liquid Anion Type in the Performance of Solid Polymer Electrolytes Based on Poly(Vinylidene fluoride‐trifluoroethylene)

The effect of different anions within the ionic liquid in the characteristics of solid polymer electrolytes (SPEs) based on P(VDF‐TrFE) has been investigated. 1‐ethyl‐3‐methylimidazolium acetate, [C₂mim][OAc], 1‐ethyl‐3‐methylimidazolium triflate, [C₂mim][(CF₃SO₃)], 1‐ethyl‐3‐methylimidazolium lactate, [C₂mim][Lactate], 1‐ethyl‐3‐methylimidazolium thiocyanate, [C₂mim][SNC] and 1‐ethyl‐3‐methylimidazolium hydrogen sulfate [C₂mim][HSO₄] have been used in SPE prepared by solvent casting. The polymer phase, thermal and electrochemical properties of the SPE have been determined. The thermal and electrical properties of the SPEs strongly depend on the selected IL, as determined by their different interactions with the polymer matrix. The room temperature ionic conductivity increases in the following way for the different anions: [SNC]>[CF₃SO₃)]>[HSO₄]>[Lactate]>[OAc], which is mainly dependent on the viscosity of the ionic liquid.     

Green and Efficient Processing of Cinnamomum cassia Bark by Using Ionic Liquids: Extraction of Essential Oil and Construction of UV‐Resistant Composite Films from Residual Biomass

There is significant interest in the development of a sustainable and integrated process for the extraction of essential oils and separation of biopolymers by using novel and efficient solvent systems. Herein, cassia essential oil enriched in coumarin is extracted from Cinnamomum cassia bark by using a protic ionic liquid (IL), ethylammonium nitrate (EAN), through dissolution and the creation of a biphasic system with the help of diethyl ether. The process has been perfected, in terms of higher biomass dissolution ability and essential oil yield through the addition of aprotic ILs (based on the 1‐butyl‐3‐methylimidazolium (C₄mim) cation and chloride or acetate anions) to EAN. After extraction of oil, cellulose‐rich material and free lignin were regenerated from biomass–IL solutions by using a 1:1 mixture of acetone–water. The purity of the extracted essential oil and biopolymers were ascertained by means of FTIR spectroscopy, NMR spectroscopy, and GC‐MS techniques. Because lignin contains UV‐blocking chromophores, the oil‐free residual lignocellulosic material has been directly utilized to construct UV‐light‐resistant composite materials in conjunction with the biopolymer chitosan. Composite material thus obtained was processed to form biodegradable films, which were characterized for mechanical and optical properties. The films showed excellent UV‐light resistance and mechanical properties, thereby making it a material suitable for packaging and light‐sensitive applications.     

Influence of ionic liquids on actinides extraction by diphenyl(dibutyl)carbamoylmethylphosphine oxide in different solvents from nitric acid solution

Influence of ionic liquids (ILs) addition (1?C50 wt%) on extraction efficiency of actinides by diphenyl(dibutyl)carbamoylmethylphosphine oxide (Ph₂Bu₂) from 3 M HNO₃ has been studied. Am(III) distribution ratios in two-phase systems 0.1 M Ph₂Bu₂ in either DCE or CHCl₃?C3 M HNO₃ depending on the nature of additional ionic liquids: imidazolium-based ILs: [C₄mim][PF₆], [C₄mim][BF₄] and phosphonium-based ILs: PPF₆, PBF₄ and PCl were determined. The highest value of Am(III) extraction ratio change (1040) was found on addition of PPF₆ to Ph₂Bu₂ in CHCl₃. Extraction of Pu(IV) and U(VI) by 0.001 M Ph₂Bu₂ in the presence of [C₄mim][PF₆] in DCE, CHCl₃ or meta-nitrobenzotrifluoride (NBTF) have been investigated. The greatest enhancement of extraction efficiency was observed using CHCl₃, the least polar studied solvent. Using a mixture of conventional solvent and ionic liquid as a solvent for extractant enables one to increase distribution ratios and reduce viscosity of organic phase as compared with ionic liquid viscosity. The marked increase of Am(III), Pu(IV) and U(VI) extraction extent by Ph₂Bu₂ on addition of ionic liquids to the extent of 10 wt% permit one essentially to diminish amounts considerably more expensive carbamoylmethylphosphine oxide(the general name is CMPO) used in TRUEX process.     

PVT properties of imidazolium-, phosphonium-, pyridinium- and pyrrolidinium-based ionic liquids using critical point constants

Song and Mason equation of state (EOS) with a simple modification has been extended to modelling PVT properties of ionic liquids (ILs). The considered ILs are [C₁mim][MeSO4], [C₁mim][CH₃OC₂H₅SO₄], [C₁mim][(CH₃)₂PO₄], [C₂mim][MeSO4], [C₂mim][BF₄], [C₂mim][SCN], [C₂eim][NTf₂], [C₄mim][C(CN)₃], [C₄mim][CF₃SO₃], [C₄mim][SCN], [C₅mim][NTf₂], [C₈mim][NTf₂], [(C₆H₁₃)₃P(C₁₄H₂₉)][Cl], [(C₆H₁₃)₃P(C₁₄H₂₉)][NTf₂], [(C₆H₁₃)₃P(C₁₄H₂₉)][Ac], [C₃mpyr][NTf₂], [C₄mpyr][NTf₂] and [Py][C₂H₅OC₂H₄SO₄]. Three temperature-dependent parameters in the proposed EOS have been scaled as functions of reduced temperature with the use of the law of corresponding states. It is shown that the knowledge of just critical temperature and critical density is sufficient to predict the PVT properties of these ILs. The overall average absolute deviation of calculated densities from literature values for 1347 data points of 18 ILs was found to be 0.58%. The predicted density of ILs from proposed EOS has been compared with those obtained by other literature work. Moreover, we indicate that the Zeno line regularity can well be predicted by proposed model for ILs.     

Lippia origanoides chemotype differentiation based on essential oil GC‐MS and principal component analysis

Chromatographic (GC/flame ionization detection, GC/MS) and statistical analyses were applied to the study of essential oils and extracts obtained from flowers, leaves, and stems of Lippia origanoides plants, growing wild in different Colombian regions. Retention indices, mass spectra, and standard substances were used in the identification of 139 substances detected in these essential oils and extracts. Principal component analysis allowed L. origanoides classification into three chemotypes, characterized according to their essential oil major components. α‐ and β‐phellandrenes, p‐cymene, and limonene distinguished chemotype A; carvacrol and thymol were the distinctive major components of chemotypes B and C, respectively. Pinocembrin (5,7‐dihydroxyflavanone) was found in L. origanoides chemotype A supercritical fluid (CO₂) extract at a concentration of 0.83±0.03 mg/g of dry plant material, which makes this plant an interesting source of an important bioactive flavanone with diverse potential applications in cosmetic, food, and pharmaceutical products.     

Investigations on the Physicochemical and Radiolytic Degradation Properties of Tri-<Emphasis Type="Italic">n</Emphasis>-butylphosphate–Ionic Liquid in the Presence of Nitric Acid

Tri-n-butylphosphate (TBP) in an ionic liquid (IL) has been proposed as a suitable alternative for the solvent extraction of actinides from nitric acid solutions. This paper reports the detailed investigations on the physicochemical and hydrodynamic properties of the solvent system containing TBP in 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([C₄mim][NTf₂]) IL. The properties such as density, viscosity, phase separation time (PST), etc., were measured for irradiated and unirradiated solvent phases composed of TBP, [C₄mim][NTf₂] and 1.1 mol·L^–1 TBP in [C₄mim][NTf₂]. The results are compared with the values obtained in acid-equilibrated IL phases. ATR–FTIR spectroscopy and dynamic light scattering measurement of the IL phase were employed to characterize the interactions among the IL, TBP and nitric acid medium, and the aggregate size of the adduct formed in the IL phase.     

Investigation of Uranium(VI) Extraction Mechanisms from Phosphoric and Sulfuric Media by 31P-NMR

Uranium extraction using DEHCNPB (butyl-1-[N,N-bis(2-ethylhexyl)carbamoyl]nonyl phosphonic acid, a bifunctional cationic extractant) has been studied to better understand mechanism differences depending on the original acidic solution (phosphoric or sulfuric). Solvent extraction batch experiments were carried out and the organic phases were probed using ³¹P-NMR. This technique enabled to demonstrate that phosphoric acid is poorly extracted by DEHCNPB ([H₃PO₄]_org < 2mM), using direct quantification in the organic phase by ³¹P-NMR spectra integration. Moreover, in the presence of uranium in the initial phosphoric acid solution, uranyl extraction by DEHCNPB competes with H₃PO₄ extraction.Average stoichiometries of U(VI)-DEHCNPB complexes in organic phases were also determined using slope analysis on uranium distribution data. Uranium seems to be extracted from a phosphoric medium by two extractant molecules, whereas more than three DEHCNPB on average would be necessary to extract uranium from a sulfuric medium. Thus, uranium is extracted according to different mechanisms depending on the nature of the initial solution.     

Extraction and high performance liquid chromatographic determination of 3-indole butyric acid in pea plants by using imidazolium-based ionic liquids as extractant

In this paper, imidazolium-based ionic liquids [C₄mim][PF₆], [C₆mim][PF₆], [C₈mim][PF₆], [C₆mim][BF₄] and [C₈mim][BF₄] were tested as extracting solvents for removal of 3-indole butyric acid (IBA) from aqueous media with subsequent determination using HPLC. Percent extraction of IBA was strongly affected by pH of aqueous phases and the chemical structures of ionic liquids (ILs). Extraction of IBA was quantitative in the pH values lower than pK_a of IBA. Considering both extraction and stripping efficiencies of IBA, [C₄mim][PF₆] was found to act more efficient than other studied ILs. Capacity of [C₄mim][PF₆] was 17.6 × 10⁻⁴ mmol IBA per 1.0 mL of IL. Ionic strength of aqueous phase and temperature had shown no serious effects on extraction efficiency of IBA. A preconcentration factor of 100 and a relative standard deviation of 1.16% were obtained. It was found that ionic liquid phase was reusable almost five times for extraction/stripping purposes. 3-Indole acetic acid showed interferential effect in the extraction step. In order to assess the applicability of the method, extraction and stripping of IBA from pea plants and some other samples were studied.     

Chemical constituents and antioxidant activity of essential oil and organic extract from the peel and kernel parts of Citrus japonica Thunb. (kumquat) from Iran

The constituents of essential oils and organic extracts from peel and kernels of Citrus japonica were analysed by GC and GC/MS. The content of essential oil in peel and kernel was 1.1 and 0.8% based on dry weight. The essential oil of C. japonica peel and kernel was characterised by a higher amount of limonene (51.0 and 47.1%) and germacrene D (12.1 and 6.3%), and the hexane extracts of its peel and kernel were characterised by a higher amount of dodecanol-1(12.9 and 20.8%) and linolenic acid (13.1 and 16.3%), respectively. The antioxidant activities of oils were evaluated by 1,1-diphenyl-2-picrylhydrazyl (DPPH) method. The results indicate that both oils from different parts of C. japonica possess considerable antioxidant activity. The fruit peel and kernel essential oil could thus be useful in the industries, chiefly in the food and pharmaceutical industries.     

Deep Eutectic Solvent-Based HS-SME Coupled with GC for the Analysis of Bioactive Terpenoids in Chamaecyparis obtusa Leaves

Headspace-solvent microextraction (HS-SME) was developed as a solvent-minimized extraction technique, but few studies have examined the applications of deep eutectic solvents (DESs) to the HS-SME of bioactive compounds. In this study, HS-SME was developed for the extraction of bioactive compounds using DESs as extraction solvents. DESs, which were prepared by mixing choline chloride (ChCl) with ethylene glycol (EG) at different ratios, were applied to the extraction of three terpenoids from Chamaecyparis obtusa leaves by HS-SME. The ChCl/EG ratio in the DESs, HS-SME conditions, such as the extraction temperature and extraction time, and sample/DES ratio were optimized. All extracts were analyzed by GC. Under optimized conditions, the limits of detection were 2.006 ng mL^?1 for linalool, 3.150 ng mL^?1 for α-terpineol and 2.129 ng mL^?1 for terpinyl acetate. The relative standard deviations were in the range of 2.1–6.8 %. The recoveries of the three terpenoids were in the range of 79.4–103 %. HS-SME is simple and rapid compared to heat reflux extraction and ultrasonic extraction. Moreover, DESs can be used in HS-SME for the extraction of a range of bioactive and volatile compounds.     

Use of headspace mulberry paper bag micro solid phase extraction for characterization of volatile aromas of essential oils from Bulgarian rose and Provence lavender

In this study, a new sampling method called headspace mulberry paper bag micro solid phase extraction (HS-MPB-μ-SPE) combined to gas chromatography-mass spectrometry has been applied for the analysis of volatile aromas of liquid essential oils from Bulgarian rose and Provence lavender. The technique uses an adsorbent (Tenax TA) contained in a mulberry paper bag, minimal amount of organic solvent. Linearities for the six-points calibration curves were excellent. LOD values were in the rage from 0.38 ng mL⁻¹ to 0.77 ng mL⁻¹. Overall, precision and recovery were generally good. Phenethyl alcohol and citronellol were the main components in the essential oil from Bulgarian rose. Linalyl acetate and linalool were the most abundant components in the essential oils from true lavender or lavandin. Additionally, the relative extraction efficiencies of proposed method have been compared with HS-SPME. The overall extraction efficiency was evaluated by the relative concentration factors (CF) of the several characteristic components. CF values by HS-MPB-μ-SPE were lower than those by headspace solid phase microextraction (HS-SPME). The HS-MPB-μ-SPE method is very simple to use, inexpensive, rapid, requires small sample amounts and solvent consumption. In addition, this method allowed combining of extraction, enrichment, and clean-up in a single step. HS-MPB-μ-SPE and GC/MS is a promising technique for the characterization of volatile aroma compounds from liquid essential oils.     

Thermophysical properties of 1-methyl-3-methylimidazolium dimethylphosphate and 1-ethyl-3-methylimidazolium diethylphosphate

The density and surface tension of 1-methyl-3-methylimidazolium dimethylphosphate, [C₁mim](CH₃O)₂PO₂ and 1-ethyl-3-methylimidazolium diethylphosphate, [C₂mim](CH₃CH₂O)₂PO₂ ionic liquids have been measured over the temperature range from (283.15 to 338.15) K. The coefficients of thermal expansion were calculated from the experimental density results using an empirical correlation for T = (283.15 to 338.15) K. Molecular volume and standard entropies of these ILs were calculated from the experimental density values. The surface properties of ILs were investigated. The critical temperature and enthalpy of vapourization were also discussed.     

Extraction and Analysis of Six Effective Components in Glycyrrhiza uralensis Fisch by Deep Eutectic Solvents (DES) Combined with Quantitative Analysis of Multi-Components by Single Marker (QAMS) Method

Deep eutectic solvents (DESs) are green organic solvents that have broad prospects in the extraction of effective components of traditional Chinese medicine. This work employed the quantitative analysis of multi-components by a single marker (QAMS) method to quantitatively determine the six effective components of glycyrrhizic acid, liquiritin, isoliquiritin apioside, liquiritigenin, isoliquiritin, and glycyrrhetinic acid in Glycyrrhiza uralensis, which was used for comprehensive evaluation of the optimal extraction process by DESs. First, Choline Chloride: Lactic Acid (ChCl-LA, molar ratio 1:1) was selected as the most suitable DES by comparing the extraction yields of different DESs. Second, the extraction protocol was investigated by extraction time, extraction temperature, liquid-to-material ratio, molar ratio, and ultrasonic power. The Box–Behnken design (BBD) combined with response surface methodology (RSM) was used to investigate the optimal DES conditions. The result showed that the best DES system was 1.3-butanediol/choline chloride (ChCl) with the molar ratio of 4:1. The optimal extraction process of licorice was 20 mL/g, the water content was 30%, and the extraction time was 41 min. The comprehensive impact factor (z) was 0.92. At the same time, it was found that the microstructure of the residue extracted by the eutectic solvent was more severely damaged than the residue after the traditional solvent extraction through observation under an electron microscope. The DES has the characteristics of high efficiency and rapidity as an extraction solution.     

Phenolic and flavonoid compounds extraction from Calophyllum inophyllum leaves

Calophyllum inophyllum has been known as a part of the mangrove forest area. This species is distributed primarily in the coastal regions of Indonesia and Africa. It is rich in bioactive compounds and has been used as a traditional medication. This work employed a single replicate of the one-factor-at-a-time experiment method to investigate optimum conditions, which resulted in the highest TPC. The three factors studied were organic solvent type (acetone, ethanol, and methanol), organic solvent concentration in water (50–100%, v/v), and extraction temperature (30–60 °C). The extraction was conducted with the percolation method. The result shows that organic solvent type, organic solvent concentration in water, and extraction temperature significantly affect the TPC, TFC, and the yield of crude extract obtained. The highest TPC (289.12 mg GAE/g of the residue of C. inophyllum leaves) was achieved with 80% methanol in water at 30 °C for 48 h. Under this condition, TFC value of 410.4 mg QE/g of the residue of C. inophyllum leaves, the yield of 2.41%, and IC₅₀ value of 0.054 µg/mL were achieved. Moreover, bis (2-ethylhexyl) phthalate was firstly detected in the extract.     

Air‐assisted liquid–liquid extraction coupled with dispersive liquid–liquid microextraction and a drying step for extraction and preconcentration of some phthalate esters from edible oils prior to their determination by GC

In this work, a new, cheap, simple, fast, and low organic solvent consuming procedure is proposed for isolation, enrichment, and gas chromatographic determination of some phthalate esters in edible oils. The method is based on a combination of air‐assisted liquid–liquid extraction and dispersive liquid–liquid microextraction followed by a drying step under N₂ gas. Several experimental parameters affecting both extraction and preconcentration steps were investigated and optimized. Under the optimum conditions for the proposed method, wide linear ranges (0.05–800 μg/L) and low detection limits (0.007–0.023 μg/L) were observed. The ranges of enrichment factors and extraction recoveries were 68–340 and 14–68%, respectively. Eventually, the target analytes were successfully determined in different edible oils using the proposed method.     

柠檬烯和柠檬烯氧化物与硫酸的非均相反应动力学

主要对天然挥发性有机物柠檬烯和柠檬烯氧化物在30%-80% (w)硫酸表面的非均相吸收反应进行了研究, 借以评估天然挥发性有机物与大气环境中的酸性气溶胶的反应活性. 采用自行搭建的配以单光子激光电离飞行时间质谱的湿壁流动反应管的设备对柠檬烯及其氧化物在硫酸表面的非均相吸收动力学进行了测定,计算了稳态摄取系数(γ). 实验结果表明, 柠檬烯氧化物在硫酸表面比只含有双键的柠檬烯的反应活性高, 室温下柠檬烯氧化物在30%-50% (w)硫酸上对应的稳态摄取系数是(7.100±0.023)×10^-5-(8.150±0.162)×10^-3. 此外, 还利用气相色谱-质谱(GC-MS)联用和电喷雾电离质谱(ESI-MS)对柠檬烯氧化物与硫酸的体相反应产物进行了研究, 产物包括单萜烯、松油醇、水合萜二醇和水合萜二醇二硫酸酯. 其中, 水合萜二醇二硫酸酯作为有机硫酸酯的一种, 能够改变气溶胶的吸湿性, 增强云凝结核的活性, 对于大气中灰霾的形成可能有明显的促进作用.