Effect of processing temperature on the superconducting properties of acetone doped MgB2 tapes

Correlation of phase formation, critical transition temperature T_c, microstructure, and critical current density J_c with sintering temperature has been studied for acetone doped MgB₂/Fe tapes. Sintering was performed at 600–850 °C for 1 h in a flowing Ar atmosphere. High boron substitution by carbon was obtained with increasing the sintering temperature; however, the acetone doped samples synthesized at 800 °C contain large size MgB₂ grains and more MgO impurities. Incomplete reaction for the acetone doped samples heated at 600 °C result in bad intergrain connectivity. At 4.2 K, the best J_c value was achieved in the acetone doped sample sintered at 700 °C, which reached 24,000 A/cm² at 10 T and 10,000 A/cm² at 12 T, respectively. Our results indicate that the small grain size and less impurity were also important for the improvement of J_c–B properties besides the substitutions of B by C.     

Anatase TiO2 nanocrystals prepared by mechanochemical synthesis and their photochemical activity studied by EPR spectroscopy

Anatase TiO₂ has been prepared by mechanochemical synthesis using TiOSO₄·xH₂O and Na₂CO₃ as starting reactants. The reaction was performed in high-energy ball mill using steel and corundum jars, respectively. The final products were obtained by annealing the milled powder in the temperature range of 300–700 °C and subsequently by washing out the water-soluble byproduct Na₂SO₄·xH₂O. When steel jars were used, the annealing in the range of 300–600 °C led to anatase. For products milled in corundum, the stability of anatase increased up to 700 °C. Transition electron microscopy (TEM) showed that crystallites with a size in the range of 20–50 nm with equiaxed morphology were obtained after milling in corundum and annealing at 600 and 700 °C. The process of photoinduced reactive hydroxyl radical generation in aerated aqueous titania suspensions was studied by EPR spectroscopy using spin trapping technique. The presence of iron impurities in the samples milled in steel substantially decreases the radical formation. The rate of radical formation is substantially affected by particle size development of TiO₂ nanopowders. The product milled in corundum and annealed at 700 °C outperforms more than twice the photochemical activity of TiO₂ Degussa P25 standard.     

Nanostructured Cu-CGO anodes fabricated using a microwave-assisted glycine–nitrate process

This work reports a study of nanostructured copper-doped gadolinium cermet (Cu-CGO) composite anodes prepared via conventional synthesis (CS) and microwave-synthesis (MS) involving the glycine–nitrate process (GNP). A detailed investigation on the mechanical properties, electrical conductivity and electrochemical performance of prepared Cu_0.5(Ce_0.9Gd_0.1)_0.5O_2−δ anodes is included. The prepared samples were characterized by techniques, such as XRD, EDX, SEM and electrical characterizations. After reduction in 10% H₂ and 90% N₂, the DC conductivities of the Cu-CGO anodes prepared via CS-GNP and MS-GNP are found to be 5.43×10³ and 1.09×10⁴ S cm⁻¹ at 700 °C, respectively. The electrochemical performances of the spin-coated anode symmetrical cells sintered at 700 °C are evaluated at cell operating temperatures of 600, 700 and 800 °C. The lowest area specific resistance (ASR) values for the Cu-CGO/CGO/Cu-CGO symmetrical cells prepared via the MS-GNP route at operating temperatures of 600, 700 and 800 °C are found to be 0.34, 0.71 and 1.10 Ω cm², respectively. The as-prepared (via MS-GNP) Cu-CGO anode exhibits excellent electrical and electrochemical performance consistent with the uniform nanostructured morphology compared with the anode prepared via CS-GNP.     

Microstructure refinement and significant improvements of magnetic properties in Pr2Fe14B/α-Fe nanocomposites

Exchange coupled (Pr,Tb)₂(Fe,Nb,Zr)₁₄B/α-Fe nanocomposites have been produced by melt spinning. A trend for perpendicular and planar c-axis orientation of the 2:14:1 phase was observed in the free surface of ribbons spun at speeds below 10 m/s and at optimal speeds, respectively. Higher wheel speeds led to the formation of an amorphous phase that transformed to 2:14:1 phase around 680°C. Optimum magnetic properties were found in samples spun at 14–17 m/s and annealed at 700°C for 20 min. The loop squareness was also found to depend mainly on the microstructure that is very sensitive to the sample composition. A few percentage of Nb and Zr suppressed the grain growth, resulting in a drastic improvement of magnetic properties, with approximate 50% enhancement in the intrinsic coercivity and an increase in maximum energy product from 5.6 kOe and 14.7 MGOe for the (Nb,Zr)-free sample to 8.2 kOe and 20.3 MGOe for the (Nb,Zr)-substituted samples, respectively. The significant improvement in magnetic properties originated from a much finer and homogeneous nanocomposite microstructure with an average grain size of 20 nm, leading to a high remanence of 0.73 M_s. Henkel plots indicate the enhancement of exchange coupling between hard and soft magnetic phases.     

Effect of calcination temperature on phase transformation,structural and optical properties of sol–gel derived ZrO2 nanostructures

Zirconia (ZrO₂) nanostructures of various sizes have been synthesized using sol–gel method followed by calcination of the samples from 500 to 700 °C. The calcined ZrO₂ powder samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier-transform infra-red spectroscopy (FT-IR), UV–visible spectroscopy (UV–vis.), Raman spectroscopy (RS) and thermogravimetric analysis (TGA). The phase transformation from tetragonal (t) to monoclinic (m) was observed. The average diameter of the ZrO₂ nanostructures calcined at 500, 600 and 700 °C was calculated to be 8, 17 and 10 nm, respectively. The ZrO₂ sample calcined at 500 °C with tetragonal phase shows a direct optical band gap of 5.1 eV. The value of optical band gap is decreased to 4.3 eV for the ZrO₂ calcined at 600 °C, which contains both tetragonal (73%) and monoclinic (27%) phases. On further calcination at 700 °C, where the ZrO₂ nanostructures have 36% tetragonal and 64% monoclinic phases, the optical band gap is calculated to be 4.8 eV. The enhancement in optical band gap for ZrO₂ calcined at 700 °C may be due to the rod like shape of ZrO₂ nanostructures. The tetragonal to monoclinic phase transformation was also confirmed by analyzing Raman spectroscopic data. The TG analysis revealed that the ZrO₂ nanostructure with dominance of monoclinic phase is found to be more stable over the tetragonal phase. In order to confirm the phase stability of the two phases of ZrO₂, single point energy is calculated corresponding to its monoclinic and tetragonal structures using density functional theory (DFT) calculations. The results obtained by theoretical calculations are in good agreement with the experimental findings.     

The unusual variations of photoluminescence and afterglow properties in monoclinic ZrO2 by annealing

The raw ZrO₂ is annealed at 600–1550 °C for 6 h. It is found that the emission at 492 nm increases greatly when the annealing temperature is higher than 1200 °C and its afterglow shows a small improvement at 1200–1450 °C and a large enhancement after annealing at 1550 °C. The results that are obtained indicate that the impurity Ti⁴⁺ in ZrO₂ is efficiently reduced to Ti³⁺ when the temperature is higher than 1200 °C, and the increase of Ti³⁺ centers contributes to the large improvement of emission at 492 nm. The thermoluminescence shows that at least two types of traps with different depths (0.65 eV and 1.46 eV) corresponding to oxygen vacancies exist in monoclinic ZrO₂. After annealing at 1200–1450 °C, some new trap clusters related to oxygen vacancies and Ti³⁺ form and causes the small improvement of afterglow at 1200–1450 °C. The large improvement of afterglow after annealing at 1550 °C originates from the sharp increase of proper shallow traps (0.65 eV) in ZrO₂. Accordingly, we present the feasible interpretations and luminescence mechanisms of monoclinic ZrO₂ for our observations.     

Mechanical properties of La0.58Sr0.4Co0.2Fe0.8O3-δ membranes

In this paper, we report on the mechanical properties of a La_0.58Sr_0.4Co_0.2Fe_0.8O_3-δ perovskite material. We use ring-on-ring bending tests with disk-shaped samples and depth-sensitive micro-indentation. In particular, the temperature dependency of fracture stress and elastic behavior are addressed. The fracture load is measured to be ～ 40% higher at room temperature (RT) than at 800 °C, which is due to the ferro-elasticity of material at RT. The stiffness shows an increase of about 50% above 600 °C and 700 °C in vacuum and air, respectively. The effect is attributed to a rhombohedral to cubic phase transition, which is not fully reversible upon cooling. The changes in phase composition with temperature are also confirmed by in-situ high temperature XRD. The transition appears to be associated with a change of heat capacity.     

Magnetic properties of nanocrystalline Fe86.7Zr3.3B4Ag6 thin film

The changes of magnetic properties with annealing temperature were studied in the amorphous Fe_86.7Zr_3.3B₄Ag₆ thin film. The thin films were deposited by a DC magnetron sputtering method, annealed at 300–700°C for 1 h in vacuum under a field of 1.5 kOe parallel to the film plane, and then furnace-cooled. As a result, it has been found that the Ag addition to Fe–Zr–B amorphous thin films resulted in the decrease of crystallization temperature to 400°C due to promoted crystallization ability. Also, it gave rise to formation of fine BCC α-Fe crystalline precipitates with a grain size smaller than 10 nm in the amorphous matrix near 400°C, and led to prominent enhancement in the magnetic properties of the Fe_86.7Zr_3.3B₄Ag₆ thin films. Significantly, excellent magnetic properties such as a saturation magnetization of 1.7 T, a coercive force of 1 Oe and a permeability of 7800 at 50 MHz were obtained in the amorphous Fe_86.7Zr_3.3B₄Ag₆ thin film containing 7.2 nm-size BCC α-Fe, which was annealed at 400°C. Also, core loss of 1.4 W cm⁻³ (B_m=0.1 T) at 1 MHz in the thin film was obtained, and it is a much lower value than had been obtained in any existing soft magnetic materials. Such excellent properties are inferred to originate from the uniform dispersion of nano-size BCC α-Fe in the amorphous matrix.     

Application of indium tin oxide (ITO) thin film as a low emissivity film on Ni-based alloy at high temperature

Indium tin oxide (ITO) films as the low emissivity coatings of Ni-based alloy at high temperature were studies. ITO films were deposited on the polished surface of alloy K424 by direct current magnetron sputtering. These ITO-coated samples were heat-treated in air at 600–900 °C for 150 h to explore the effect of high temperature environment on the emissivity. The samples were analyzed by X-ray diffraction (XRD), SEM and EDS. The results show that the surface of sample is integrity after heat processing at 700 °C and below it. A small amount of fine crack is observed on the surface of sample heated at 800 °C and Ti oxide appears. There are lots of fine cracks on the sample annealed at 900 °C and a large number of various oxides are detected. The average infrared emissivities at 3–5 μm and 8–14 μm wavebands were tested by an infrared emissivity measurement instrument. The results show the emissivity of the sample after annealed at 600 and 700 °C is still kept at a low value as the sample before annealed. The ITO film can be used as a low emissivity coating of super alloy K424 up to 700 °C.     

Preparation of phase pure and well-crystallized Li4Ti5O12 nanoparticles by precision control of starting mixture and calcining at lowest possible temperatures

In an attempt to obtain spinel Li₄Ti₅O₁₂ with smallest possible grain size and highest possible phase purity via a solid state route, we tried to elevate reactivity of the reactant mixture by mechanical activation and appropriate choice of the starting materials. From the stoichiometric mixture comprising Li₂CO₃ and 150 nm anatase, we needed to heat at 950 °C for 1 h to obtain 81–88% phase purity (PhP) of Li₄Ti₅O₁₂ with its average grain size ca 600 nm. After mechanical activation with a multi-ring mill for 30 min, 850 °C was enough to obtain 85–87% pure 500 nm spinel. From a combination of LiNO₃ and 50 nm anatase, 90–91% phase pure product with its grain size 240 nm was obtained at 750 °C due to fusion of the nitrate and shorter diffusion path. By using CH₃COOLi.2H₂O and 50 nm anatase we obtained 130 nm Li₄Ti₅O₁₂ with its PhP ca 90% by milling the mixture preliminarily calcined at 500 °C for 1 h and heating subsequently at 700 for 1 h.     

Cathodoluminescence studies of un-doped and (Cu,Fe, and Co)-doped tin dioxide films deposited by spray pyrolysis

Un-doped and (Cu, Fe, and Co)-doped SnO₂ were studied using films deposited by spray pyrolysis. Room temperature cathodoluminescence (CL) was measured. Differences in CL spectra were observed as a function of deposition parameters (T_sub-350–550 °C), the nature and concentration of dopants (0–16 at.%), and the resulting high annealing temperature (T_an = 700–950 °C). A possible luminescence mechanism has been discussed. It was established that changes taking place in CL spectra were caused by the change of both the grain size and crystallinity (stoichiometry) of the surface layer. It was concluded that radiative recombination occurs through shallow donor levels associated with O-vacancies and trapped centers. It was assumed that in SnO₂ there are apparently three types of defects forming deep levels located at 0.8–0.9, 1.3–1.4, and ∼1.6 eV from the top of the valence band.     

Structure and magnetic properties of 300-nm-thick FePt films with Hf underlayer

Structure, microstructure, magnetic properties of 300-nm-thick FePt films with 10-nm-thick Hf underlayer have been studied. The experimental results showed that the very thin Hf underlayer could promote the ordering at reduced temperatures by facilitating the nucleation of the order phase, leading to refined grain size and magnetic domain size. Therefore, the permanent magnetic properties of FePt films were enhanced. (BH)_max and H_c of FePt films were greatly enhanced from 5.0–21.0 MGOe and 1.4–11.0 kOe for single layer to 10.2–23.6 MGOe and 4.5–13.2 kOe for Hf-underlayered films annealed in T_a region of 400–600 °C, respectively. Nevertheless, the severe interdiffusion between the Hf and FePt layers at T_a=800 °C resulted in the decreased S, coarsened surface morphology, grain and magnetic domain sizes, and therefore the slightly decreased (BH)_max to 18.0 MGOe.     

Sintering kinetics and oxide ion conduction in Sr-doped apatite-type lanthanum silicates,La9Sr1Si6O26.5

These last past years, a major interest has been devoted to decrease the working temperature of solid oxide fuel cells (SOFCs) down to about 700 °C.Apatite materials (La_10 ? xSr_xSi₆O_27?x/2) are attractive candidates for solid electrolytes, with a high ionic conductivity at these intermediate temperatures. An apatite powder (x = 1) with a 0.75 µm mean particle size, produced by solid state reaction, was tape cast to obtain green sheets with a thickness of about 260 µm.On one hand, the densification mechanism of the apatite ceramic during the intermediate solid state sintering has been approached. It appeared from the kinetical tests performed under isothermal conditions between 1250 and 1550 °C, that densification could be controlled by the diffusion at grain boundaries of the rare-earth element, La, with an activation energy of 470 kJ/mol.On the other hand, conductivity measurements were performed on apatite samples sintered at 1400 and 1500 °C. The ionic conductivity was mainly sensitive to the presence of secondary phases at 1400 °C. The ionic conductivity of the apatite sintered at 1500 °C (mean grain size = 3.9 µm) is equal to 1.2 × 10^? 2 S/cm at 700 °C.     

A facile thermal evaporation route for large-area synthesis of tin oxide nanowires: Characterizations and their use for liquid petroleum gas sensor

In this paper, a very simple procedure was presented for the reproducible synthesis of large-area SnO₂ nanowires (NWs) on a silicon substrate by evaporating Sn powders at temperatures of 700, 750, and 800 °C. As-obtained SnO₂ NWs were characterized by field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and Raman spectroscopy. They revealed that the morphology of the NWs is affected by growth temperature and the SnO₂ NWs are single-crystalline tetragonal. The band gap of the NWs is in the range of 4.2–4.3 eV as determined from UV/visible absorption. The NWs show stable photoluminescence with an emission peak centered at around 620 nm at room-temperature. The sensors fabricated from the SnO₂ NWs synthesized at 700 °C exhibited good response to LPG (liquefied petroleum gas) at an operating temperature of 400 °C.     

Growth and characterization of CoSi2 films on Si (1 0 0) substrates

In the present work, a special solid phase epitaxy method has been adapted for the preparation of CoSi₂ film. This method includes an epitaxial growth of Co films on Si (1 0 0) substrate, and in situ annealing of the Co/Si films in vacuum. It has been found that at the substrate temperature of 360°C, fcc cobalt film grows epitaxially on the Si (1 0 0) surface. The crystallographic orientation relations between fcc Co film and Si substrate determined from the electron diffraction result are: (0 0 1) Co//(0 0 1) Si, [1 0 0] Co//[1 1 0]Si. Upon annealing at temperatures range from 500 to 600°C, Co film reacts with Si substrate and transforms into CoSi₂. The CoSi₂ films prepared by this way are characterized by XTEM, XPS and AFM.     

Sensor application-related defect chemistry and electromechanical properties of langasite

The operation of langasite (La₃Ga₅SiO₁₄) resonators as sensors at elevated temperature and controlled atmospheres is examined. This paper focuses on mapping the regimes of gas-insensitive operation of uncoated langasite resonators and the correlation to langasite's defect chemistry for temperatures up to 1000 °C. As a measure of sensitivity, the fundamental resonant mode at 5 MHz is estimated to be determined to within ± 4 Hz by network analysis for resonators operated in air at temperatures below 1000 °C. The calculated frequency shift induced by redox-related reactions in langasite only exceeds the limit of ± 4 Hz below p_O2 ≈ 10^− 17 bar at 1000 °C, below 10^− 24 bar at 800 °C and below 10^− 36 bar at 600 °C. Water vapor is found to shift the resonance frequency at higher oxygen partial pressures. In the hydrogen-containing atmospheres applied here, langasite can be regarded as a stable resonator material above oxygen partial pressures of about 10^− 13 and 10^− 20 bar at 800 and 600 °C, respectively.     

Effects of doping with nanoscale Co3O4 particles on the superconducting properties of powder-in-tube processed MgB2 tapes

Nanoscale Co₃O₄ particles were doped into MgB₂ tapes with the aim of developing superconducting wires with high-current-carrying capacity. Fe-sheathed MgB₂ tapes with a mono-core were prepared using the in situ powder-in-tube (PIT) process with the addition of 0.2–1.0 mol% Co₃O₄. The critical temperature decreased monotonically with an increasing amount of doped Co₃O₄ particles for all heat-treatment temperatures from 600 to 900 °C. However, the transport critical current density (J_c) at 4.2 K varied with the heat-treatment temperatures. The J_c values in magnetic fields ranging from 7 to 12 T decreased monotonically with increasing Co₃O₄ doping level for a heat-treatment temperature of 600 °C. In contrast, some improvements on the J_c values of the Co₃O₄ doped tapes were observed in the magnetic fields below 10 T for 700 and 800 °C. Furthermore, J_c values in all the fields measured increased as the Co₃O₄ doping level increase from 0 to 1 mol% for 900 °C. This heat-treatment temperature dependence of the J_c values could be explained in terms of the heat-treatment temperature dependence of the irreversibility field with Co₃O₄ doping.     

Characterization and organic electric-double-layer-capacitor application of KOH activated coal-tar-pitch-based carbons: Effect of carbonization temperature

The present study reports the influence of pre-carbonization on the properties of KOH-activated coal tar pitch (CTP). The change of crystallinity and pore structure of pre-carbonized CTPs as well as their activated carbons (ACs) as function of pre-carbonization temperature are investigated. The crystallinity of pre-carbonized CTPs increases with increasing the carbonization temperature up to 600 °C, but a disorder occurs during the carbonization around 700 °C and an order happens gradually with increasing the carbonization temperatures in range of 800–1000 °C. The CTPs pre-carbonized at high temperatures are more difficult to be activated with KOH than those pre-carbonized at low temperatures due to the increase of micro-crystalline size and the decrease of surface functional groups. The micro-pores and meso-pores are well developed at around 1.0 nm and 2.4 nm, respectively, as the ACs are pre-carbonized at temperatures of 500–600 °C, exhibiting high specific capacitances as electrode materials for electric double layer capacitor (EDLC). Although the specific surface area (SSA) and pore volume of ACs pre-carbonized at temperatures of 900–1000 °C are extraordinary low (non-porous) as compared to those of AC pre-carbonized at 600 °C, their specific capacitances are comparable to each other. The large specific capacitances with low SSA ACs can be attributed to the structural change resulting from the electrochemical activation during the 1st charge above 2.0 V.     

Understanding of redox behavior of Ni–YSZ cermets

The oxidation of Ni–YSZ cermet as well the reduction of re-oxidized Ni–YSZ cermet was investigated by using temperature-programmed oxidation (TPO), temperature-programmed reduction (TPR) and scanning electron microscope (SEM). The scanning electron microscope (SEM) photographs and temperature-programmed reduction (TPR) profiles indicated that the sintering of smaller nickel oxide crystallites to larger aggregates occurred concurrently with the formation of smaller nickel oxide crystallites from the oxidation of nickel at 800 °C, and the sintering of smaller nickel oxide crystallites at 600 °C was slower than that at 800 °C. The SEM results showed that each Ni particle was separated into a lot of smaller NiO particles during oxidation. The TPO profiles showed that two kinds of nickel particles exist in the anode reduced at 800 and 600 °C, one with high activity towards oxidation for the nickel crystallites directly from reduction, and another one with low activity towards oxidation for the sintered nickel particles. The Ni–YSZ anodes reduced at higher temperature showed higher re-oxidation temperature than the one reduced at lower temperature because of the accelerated passivating and sintering of the smaller nickel particles at higher temperature. The re-oxidation profiles were almost unchanged during redox cycling at 600 °C, whereas the re-oxidation peak temperature decreased during redox cycling at 800 °C, indicating that the primary nickel grains split to smaller ones upon cyclic reduction at higher temperature.     

Synthesis of Y-doped BaCeO3 nanopowders by a modified solid-state process and conductivity of dense fine-grained ceramics

Powders of BaY_xCe_1 ? xO_3 ? δ (x = 0, 0.1 and 0.15) with specific surface area of 6–8 m²g^? 1 (BET equivalent particle size of 130–160 nm) were prepared by a modified solid-state route using nanocrystalline BaCO₃ and CeO₂ raw materials. These powders showed excellent densification at relatively low temperatures. Dense (96–97% relative density) ceramics with submicron grain size (0–4–0.6 µm) were obtained after sintering at 1250–1280 °C. Ceramics sintered at 1450 °C revealed only a moderate grain growth (grain size ≤ 2 µm), uniform microstructure and very high density (≥ 98%). The total conductivity of the submicron ceramics at 600 °C was comparable with the reference values reported in the literature, meaning that the high number of grain boundaries was not a limiting factor. On lowering temperature, the contribution of the blocking grain boundaries becomes progressively more important and the conductivity decreases in comparison to coarse-grained ceramics. Microscopic conductivities of grain interior and grain boundary are the same irrespective of grain size meaning that the different macroscopic behaviour is only determined by a geometric factor (a trivial size effect).