Effect of Li2O Addition on the Preparation of (Y2‐yLiy)Ti2O7‐y

A new series of (Y_2‐yLi_y)Ti₂O_7‐y having an ordered pyrochlore phase was prepared by a solid state reaction method with a solid solution range of 0.05 ≥ y ≥ 0.10. Unit cell parameters obtained by the Rietveld refinement method shows that the a‐axis decreases linearly with increasing the amount of Li ion addition, indicating the successful incorporation of the Li ion into unit cell. The average x‐fractional coordinate of the O(1) site depends on the ionic radius ratio of r(A³+)/r(Ti⁴⁺) in the A₂Ti₂O₇ with a pyrochlore phase. The Ti K‐edge XANES spectra of the (Y_2‐yLi_y)Ti₂O_7‐y show that the valence of the Ti ions is slightly less than 4 so that Ti is in the mixed valence state. Average particle size increases with increasing the amount of extra Li ion addition, which acts as a flux to lower the melting point of the materials.     

Activated Single-Phase Ti4O7 Nanosheets with Efficient Use of Precious Metal for Inspired Oxygen Reduction Reaction

The oxygen reduction reaction (ORR) is central to modern energy storage and conversion technologies for grids such as fuel cells and electrolyzers, but challenges remain due to the lack of reliable, economic, and durable electrocatalysts. Here, we develop single-crystal conductive black titanium (Ti₄O₇) nanosheets (NSs) as a new precious metal carrier based on sacrificial hard templates and ultrasonic-assisted peeling, and deposit Pt clusters on Ti₄O₇ NSs induced by wetness impregnation under the irradiation of visible light (VI; 650 nm). Pt/Ti₄O₇ NSs provide Ti³⁺, Pt²⁺, and Pt⁰⁺ continuous active sites for the ORR multielectron process, achieving synergy among them. The assistance of visible light not only makes a more uniform and smaller distribution of Pt nanoclusters, but also strengthens the charge transfer, thereby constructing a strong metal-support interaction interface. VI−Pt/Ti₄O₇ NSs show superior initial oxidation potential and a mass activity of 1.61 A mg⁻¹_Pt at a E_1/2=0.91 V, which is nine times higher than that of commercial Pt/C. This work provides an effective strategy for achieving high-value applications of titanium sub-oxides and further explores the enhanced interface in metals Ti_nO_2n-1 by light radiation.     

A generic method of visible light sensitization for perovskite-related layered oxides: Substitution effect of lead

Nearly complete substitution of lead into layered perovskites is a generic method of visible light sensitization for these ultraviolet (UV)-active materials. Thus, CaBi₄Ti₄O₁₅ (Aurivillius phase), K_0.5La_0.5Ca_1.5Nb₃O₁₀ (Dion-Jacobson phase), and Sr₃Ti₂O₇ (Ruddlesden-Popper phase) are photocatalysts, all working under UV light, but their analogs containing lead (PbBi₄Ti₄O₁₅, K_0.5La_0.25Bi_0.25Ca_0.75Pb_0.75Nb₃O₁₀, and PbTiO₃) absorb visible light and exhibit photocatalytic activity of decomposition of water under visible light.     

PbS插层K2Ti4O9催化剂：制备及光催化制氢活性

利用高温固相反应、离子交换、层间插入反应和硫化处理制备了PbS插层的K2Ti4O9催化剂。利用XRD、TEM、SEM、XRF、PL和紫外-可见漫反射光谱对催化剂进行了表征,考察了催化剂紫外光和可见光光催化制氢活性。结果表明,制备的PbS插层K2Ti4O9催化剂对可见光的吸收范围较宽,其吸收边界约为710 nm,在紫外光和可见光下3 h累积产氢量可达到115.46 mmol.gcat-1和0.92 mmol.gcat-1,与CdS插层K2Ti4O9催化剂相比具有更高的催化活性。     

Advanced Bi<Subscript>2</Subscript>O<Subscript>2.7</Subscript>/Bi<Subscript>2</Subscript>Ti<Subscript>2</Subscript>O<Subscript>7</Subscript> composite film with enhanced visible-light-driven activity for the degradation of organic dyes

Bi₂O_2.7/Bi₂Ti₂O₇ composite photocatalyst films are synthesized by sol–gel dip-coating. The ratio of adding Bi and Ti precursors can be controlled during the preparation process. The phase structure is confirmed by X-ray diffraction. The UV–visible diffuse reflectance spectrum shows that the composite catalysts present light absorption in the visible region. The obtained Bi₂O_2.7/Bi₂Ti₂O₇ composite films possess superior photocatalytic degradation of rhodamine B, owing to the visible light response of Bi₂O_2.7 and the separation of photogenerated electrons and holes between the two components. As a result, the Bi₂O_2.7/Bi₂Ti₂O₇ (Bi/Ti = 1:1) displays the highest photocatalytic activity under visible light or UV light irradiation for the degradation of different organic dyes, including methyl blue, methyl orange and acid orange 7.     

Two‐Dimensional Perovskite Oxynitride K2LaTa2O6N with an H+/K+ Exchangeability in Aqueous Solution Forming a Stable Photocatalyst for Visible‐Light H2 Evolution

Undoped layered oxynitrides have not been considered as promising H₂‐evolution photocatalysts because of the low chemical stability of oxynitrides in aqueous solution. Here, we demonstrate the synthesis of a new layered perovskite oxynitride, K₂LaTa₂O₆N, as an exceptional example of a water‐tolerant photocatalyst for H₂ evolution under visible light. The material underwent in‐situ H⁺/K⁺ exchange in aqueous solution while keeping its visible‐light‐absorption capability. Protonated K₂LaTa₂O₆N, modified with an Ir cocatalyst, exhibited excellent catalytic activity toward H₂ evolution in the presence of I^? as an electron donor and under visible light; the activity was six times higher than Pt/ZrO₂/TaON, one of the best‐performing oxynitride photocatalysts for H₂ evolution. Overall water splitting was also achieved using the Ir‐loaded, protonated K₂LaTa₂O₆N in combination with Cs‐modified Pt/WO₃ as an O₂ evolution photocatalyst in the presence of an I₃^?/I^? shuttle redox couple.     

Ce掺杂K2La2Ti3O10催化剂的可见光高效催化制氢的研究

采用高温固相法合成了铈掺杂的K₂La₂Ti₃O₁₀催化剂, 利用X射线衍射(XRD)、紫外-可见漫反射(UV-vis DRS)、透射电镜(TEM)和X射线光电子能谱(XPS)对催化剂进行了表征. 考察了催化剂的可见光催化分解甲醇水溶液制氢的活性, 并对可见光催化机理进行了分析. 研究表明, 铈的掺杂没有改变K₂La₂Ti₃O₁₀的微晶结构, 并使催化剂粒径有所减小. 紫外可见漫反射分析表明禁带宽度为2.3 eV左右, 对可见光具有较高吸收. XPS表明La和Ti为＋3和＋4价, 而Ce则是＋3和＋4的混合价态. 担载2 wt% Pt后, 在可见光下光催化活性大大提高, 当铈的掺杂量为0.5 mol%(即Ce取代La的摩尔百分量)时, 光催化活性达到最大, 产氢速率为0.05 mmol/h; 光照5 h后产氢量为0.22 mmol, 而纯K₂La₂Ti₃O₁₀的产氢量只有0.037 mmol.     

A Redox‐Mediator‐Free Solar‐Driven Z‐Scheme Water‐Splitting System Consisting of Modified Ta3N5 as an Oxygen‐Evolution Photocatalyst

Tantalum nitride (Ta₃N₅) modified with various O₂‐evolution cocatalysts was employed as a photocatalyst for water oxidation under visible light (λ>420 nm) in an attempt to construct a redox‐mediator‐free Z‐scheme water‐splitting system. Ta₃N₅ was prepared by nitriding Ta₂O₅ powder under a flow of NH₃ at 1023–1223 K. The activity of Ta₃N₅ for water oxidation from an aqueous AgNO₃ solution as an electron acceptor without cocatalyst was dependent on the generation of a well‐crystallized Ta₃N₅ phase with a low density of anionic defects. Modification of Ta₃N₅ with nanoparticulate metal oxides as cocatalysts for O₂ evolution improved water‐oxidation activity. Of the cocatalysts examined, cobalt oxide (CoO_x) was found to be the most effective, improving the water‐oxidation efficiency of Ta₃N₅ by six to seven times. Further modification of CoO_x/Ta₃N₅ with metallic Ir as an electron sink allowed one to achieve Z‐scheme water splitting under simulated sunlight through interparticle electron transfer without the need for a shuttle redox mediator in combination with Ru‐loaded SrTiO₃ doped with Rh as a H₂‐evolution photocatalyst.     

Visible and infrared luminescence properties of Er-doped Y2Ti2O7 nanocrystals

Er³⁺-doped Y₂Ti₂O₇ nanocrystals were fabricated by the sol-gel method. While the annealing temperature exceeds 757 °C, amorphous pyrochlore phase Er_xY_2−xTi₂O₇ transfers to well-crystallized nanocrystals, and the average crystal size increases from ∼70 to ∼180 nm under 800-1000 °C/1 h annealing. Er_xY_2−xTi₂O₇ nanocrystals absorbing 980 nm photons can produce the upconversion (526, 547, and 660 nm; ²H_11/2→⁴I_15/2, ⁴S_3/2→⁴I_15/2, and ⁴F_9/2→⁴I_15/2, respectively) and Stokes (1528 nm; ⁴I_13/2→⁴I_15/2) photoluminescence (PL). The infrared PL decay curve is single-exponential for Er³⁺ (5 mol%)-doped Y₂Ti₂O₇ nanocrystals but slightly nonexponential for Er³⁺ (10 mol%)-doped Y₂Ti₂O₇ nanocrystals. For 5 and 10 mol% doping concentrations, the mechanism of up-converted green light is the two-photon excited-state absorption. Much stronger intensity of red light relative to green light was observed for the sample with 10 mol% dopant. This phenomenon can be attributed to the reduced distance between Er³⁺-Er³⁺ ions, resulting in the enhancement of the energy-transfer upconversion and cross-relaxation mechanisms.     

Different Reactivity of Rutile and Anatase TiO2 Nanoparticles: Synthesis and Surface States of Nanoparticles of Mixed-Valence Magnéli Oxides

Magnéli phases Ti_nO_2n−1 (3<n≤10) are mixed Ti⁴⁺/Ti³⁺ oxides with high electrical conductivity. When used for water remediation or electrochemical energy storage and conversion, they are nanostructured and exposed to various environments. Therefore, understanding their surface reactivity is of prime importance. Such studies have been hindered by carbon contamination from syntheses. Herein, this synthetic and characterization challenge is addressed through a new approach to 50 nm carbon-free Ti₄O₇ and Ti₆O₁₁ nanoparticles. It takes advantage of the different reactivities of rutile and anatase TiO₂ nanoparticles towards H₂, to use the former as precursor of Ti_nO_2n−1 and the latter as a diluting agent. This approach is combined with silica templating to restrain particle growth. The surface reactivity of the Magnéli nanoparticles under different atmospheres was then evaluated quantitatively by synchrotron-radiation-based X-ray photoelectron spectroscopy, which revealed oxidized surfaces with lower conductivity than the core. This finding sheds a new light on the charge transfer occurring in these materials.     

Zwei Chloridsilicate des Yttriums: Y3Cl[SiO4]2 und Y6Cl10[Si4O12]

Two Chloride Silicates of Yttrium: Y₃Cl[SiO₄]₂ and Y₆Cl₁₀[Si₄O₁₂] The chloride‐poor yttrium(III) chloride silicate Y₃Cl[SiO₄]₂ crystallizes orthorhombically (a = 685.84(4), b = 1775.23(14), c = 618.65(4) pm; Z = 4) in space group Pnma. Single crystals are obtained by the reaction of Y₂O₃, YCl₃ and SiO₂ in the stoichiometric ratio 4 : 1 : 6 with ten times the molar amount of YCl₃ as flux in evacuated silica tubes (7 d, 1000 °C) as colorless, strongly light‐reflecting platelets, insensitive to air and water. The crystal structure contains isolated orthosilicate units [SiO₄]^4– and comprises cationic layers {(Y2)Cl}²⁺ which are alternatingly piled parallel (010) with anionic double layers {(Y1)₂[SiO₄]₂}^2–. Both crystallographic different Y³⁺ cations exhibit coordination numbers of eight. Y1 is surrounded by one Cl^– and 7 O^2– anions as a distorted trigonal dodecahedron, whereas the coordination polyhedra around Y2 show the shape of bicapped trigonal prisms consisting of 2 Cl^– and 6 O^2– anions. The chloride‐rich chloride silicate Y₆Cl₁₀[Si₄O₁₂] crystallizes monoclinically (a = 1061,46(8), b = 1030,91(6), c = 1156,15(9) pm, β = 103,279(8)°; Z = 2) in space group C2/m. By the reaction of Y₂O₃, YCl₃ and SiO₂ in 2 : 5 : 6‐molar ratio with the double amount of YCl₃ as flux in evacuated silica tubes (7 d, 850 °C), colorless, air‐ and water‐resistant, brittle single crystals emerge as pseudo‐octagonal columns. Here also a layered structure parallel (001) with distinguished cationic double‐layers {(Y2)₅Cl₉}⁶⁺ and anionic layers {(Y1)Cl[Si₄O₁₂]}^6– is present. The latter ones contain discrete cyclo‐tetrasilicate units [Si₄O₁₂]^8– of four cyclically corner‐linked [SiO₄] tetrahedra in all‐ecliptical arrangement. The coordination sphere around (Y1)³⁺ (CN = 8) has the shape of a slightly distorted hexagonal bipyramid comprising 2 Cl^– and 6 O^2– anions. The 5 Cl^– and 2 O^2– anions building the coordination polyhedra around (Y2)³⁺ (CN = 7) form a strongly distorted pentagonal bipyramid.     

Light‐Harvesting Photocatalysis for Water Oxidation Using Mesoporous Organosilica

An organic‐based photocatalysis system for water oxidation, with visible‐light harvesting antennae, was constructed using periodic mesoporous organosilica (PMO). PMO containing acridone groups in the framework (Acd‐PMO), a visible‐light harvesting antenna, was supported with [Ru^II(bpy)₃²⁺] complex (bpy=2,2′‐bipyridyl) coupled with iridium oxide (IrO_x) particles in the mesochannels as photosensitizer and catalyst, respectively. Acd‐PMO absorbed visible light and funneled the light energy into the Ru complex in the mesochannels through excitation energy transfer. The excited state of Ru complex is oxidatively quenched by a sacrificial oxidant (Na₂S₂O₈) to form Ru³⁺ species. The Ru³⁺ species extracts an electron from IrO_x to oxidize water for oxygen production. The reaction quantum yield was 0.34 %, which was improved to 0.68 or 1.2 % by the modifications of PMO. A unique sequence of reactions mimicking natural photosystem II, 1) light‐harvesting, 2) charge separation, and 3) oxygen generation, were realized for the first time by using the light‐harvesting PMO.     

Room‐Temperature and Aqueous‐Phase Synthesis of Plasmonic Molybdenum Oxide Nanoparticles for Visible‐Light‐Enhanced Hydrogen Generation

A straightforward aqueous synthesis of MoO_3?x nanoparticles at room temperature was developed by using (NH₄)₆Mo₇O₂₄?4 H₂O and MoCl₅ as precursors in the absence of reductants, inert gas, and organic solvents. SEM and TEM images indicate the as‐prepared products are nanoparticles with diameters of 90–180 nm. The diffuse reflectance UV‐visible‐near‐IR spectra of the samples indicate localized surface plasmon resonance (LSPR) properties generated by the introduction of oxygen vacancies. Owing to its strong plasmonic absorption in the visible‐light and near‐infrared region, such nanostructures exhibit an enhancement of activity toward visible‐light catalytic hydrogen generation. MoO_3?x nanoparticles synthesized with a molar ratio of Mo^VI/Mo^V 1:1 show the highest yield of H₂ evolution. The cycling catalytic performance has been investigated to indicate the structural and chemical stability of the as‐prepared plasmonic MoO_3?x nanoparticles, which reveals its potential application in visible‐light catalytic hydrogen production.     

Unconventional Luminescent Centers in Metastable Phases Created by Topochemical Reduction Reactions

A low‐temperature topochemical reduction strategy is used herein to prepare unconventional phosphors with luminescence covering the biological and/or telecommunications optical windows. This approach is demonstrated by using Bi^III‐doped Y₂O₃ (Y_2?xBi_xO₃) as a model system. Experimental results suggest that topochemical treatment of Y_2?xBi_xO₃ using CaH₂ creates randomly distributed oxygen vacancies in the matrix, resulting in the change of the oxidation states of Bi to lower oxidation states. The change of the Bi coordination environments from the [BiO₆] octahedra in Y_2?xBi_xO₃ to the oxygen‐deficient [BiO_6?z] polyhedra in reduced phases leads to a shift of the emission maximum from the visible to the near‐infrared region. The generality of this approach was further demonstrated with other phosphors. Our findings suggest that this strategy can be used to explore Bi‐doped or other classes of luminescent systems, thus opening up new avenues to develop novel optical materials.     

Bi2Ti2O7/TiO2复合纤维：原位水热合成及光催化性能

采用静电纺丝技术制备的TiO2纤维作为模板和反应物,通过原位水热合成了具有异质结构的Bi2Ti2O7/TiO2复合纤维。利用X射线衍射(XRD)、扫描电镜(SEM)、能量散射光谱(EDS)、高分辨透射电镜(HRTEM)和紫外可见吸收光谱(UV-Vis)等分析测试手段对样品的结构和形貌进行表征。以罗丹明B为模拟有机污染物进行光催化降解实验。结果表明:花状Bi2Ti2O7纳米结构均匀地生长在TiO2纤维上,制备了Bi2Ti2O7与TiO2相复合的光催化材料,其光谱响应范围拓宽至可见光区,与纯TiO2纤维相比可见光催化活性显著提高,且易于分离、回收和循环使用。初步探讨了Bi2Ti2O7/TiO2异质结的生长机制和光催化活性提高机理。     

球形Bi_4Ti_3O_(12)制备及其可见光催化性能

采用水热法合成球形钛酸铋复合氧化物光催化剂,利用SEM、XRD和UV-Vis DRS等表征手段对复合氧化物的晶体结构、微观形貌和光学性能进行了分析,结果表明,制备的钛酸铋复合氧化物为10 nm的球形颗粒,具有良好的晶型结构,禁带宽度为2.7 nm,有较好的可见光吸收能力。以亚甲基蓝、甲基橙及酸性品红为目标污染物,研究了复合氧化物在可见光下的光催化降解有机污染物的性能,并对光催化降解机理进行了探讨。结果表明,在可见光照射下,该复合氧化物对酸性品红降解效果明显优于亚甲基蓝和甲基橙,光照150 min下,降解率可达91%。     

球形Bi4Ti3O12制备及其可见光催化性能

采用水热法合成球形钛酸铋复合氧化物光催化剂,利用SEM、XRD和UV-Vis DRS等表征手段对复合氧化物的晶体结构、微观形貌和光学性能进行了分析,结果表明,制备的钛酸铋复合氧化物为10 nm的球形颗粒,具有良好的晶型结构,禁带宽度为2.7 nm,有较好的可见光吸收能力。以亚甲基蓝、甲基橙及酸性品红为目标污染物,研究了复合氧化物在可见光下的光催化降解有机污染物的性能,并对光催化降解机理进行了探讨。结果表明,在可见光照射下,该复合氧化物对酸性品红降解效果明显优于亚甲基蓝和甲基橙,光照150 min下,降解率可达91%。     

Ti3C2: An Ideal Co‐catalyst?

How 2D Ti₃C₂ enhances photocatalytic efficiency remains unclear. Now, it is shown that it is graphene quantum dots (GQDs) derived from Ti₃C₂, rather than 2D Ti₃C₂ itself, that play the role of co‐catalyst for La₂Ti₂O₇/Ti₃C₂ (LTC) composites during the photocatalytic reaction. After modification of Ti₃C₂ derivatives, the photocatalytic efficiency of La₂Ti₂O₇ is enhanced 16 times over pure La₂Ti₂O₇. Solid‐state NMR, Raman, and HRTEM results confirm the existence of GQDs in Ti₃C₂ and LTC composites. The GQDs are formed during the chemical change from Ti₃AlC₂ to Ti₃C₂ via HF etching, as Ti atoms are removed and unsaturated carbon bonds are left, which react with each other to form sp² π‐conjugation GQDs. 2D Ti₃C₂ is completely oxidized to CO_x modified TiO_x species, causing Ti₃C₂ to lose its electrical conductivity and the role as co‐catalyst. GQDs largely suppress the photogenerated charge recombination of La₂Ti₂O₇, as revealed by the photoluminescence (PL) and transient photocurrent.     

Aerosol-Gel Deposition of Optically Active Thin Films in the System Y2Ti2O7-Er2Ti2O7

Optically active thin films in the system Y₂Ti₂O₇-Er₂Ti₂O₇ (YETO) have been deposited using the Aerosol-gel process. Depending on the heat-treatment temperature, amorphous or crystalline films could be prepared in the range 600–950°C. The study shows that dilution of erbium ions within a Y₂Ti₂O₇ (YTO) matrix allows to prevent short range distance interactions between those ions and to promote good photoluminescence properties of YETO films. These properties are discussed and compared with those of sol-gel derived silica films doped with erbium.     

Preparation and Structure of Cerium Titanates Ce2TiO5, Ce2TiO7, and Ce4Ti9O24

Compounds Ce₂TiO₅, Ce₂Ti₂O₇, and Ce₄Ti₉O₂₄ were prepared by heating appropriate mixtures of solids containing Ce⁴⁺ and Ti³⁺ or Ti which were placed in a platinum-silica-ampoule combination at T = 1250°C (3d) under vacuum. The new compounds were characterized by powder patterns. We obtained Ce₂TiO₅ which is isotypic to La₂TiO₅ and crystallizes in the Y₂TiO₅-type (space group Pnma) with a = 10.877(6) Å, b = 3.893(1) Å, c = 11.389(8) Å, Z = 4. Ce₂Ti₂O₇ is isotypic to La₂Ti₂O₇ and crystallizes in the monoclinic Ca₂Nb₂O₇ type (space group P 2₁) with a = 7.776(6) Å, b = 5.515(4) Å, c = 12.999(6) Å, β = 98.36(5), Z = 4. The compound Ce₄Ti₉O₂₄ crystallizes orthorhombic with a = 14.082(4) Å, b = 35.419(8) Å, c = 14.516(4) Å, Z = 16. The new cerium titanate Ce₄Ti₉O₂₄ is isotypic to Nd₄Ti₉O₂₄ (space group Fddd (No. 70)) which represents a novel type of structure.