Determination of cyanide by a flow injection analysis-atomic absorption spectrometric method

A new flow injection analysis (FIA) procedure is proposed for the indirect atomic absorption spectrometric determination of cyanide. The FIA manifold is based on the insertion of the sample into a distilled water carrier, then the sample flows through a solid-phase reactor filled with silver iodide entrapped in polymeric resin beads. The calibration graph is linear over the range 0.2-6.0 mg l-1 of cyanide (correlation coefficient 0.9974), the detection limit is 0.1 mg l-1, the sample throughput is 193 h-1 and the RSD is 0.8%. The method is simple, quick and more selective than other published FIA procedures. The reproducibility obtained by using different solid-phase reactors and solutions is in the range 2.2-3.1% (RSD). The method was applied to the determination of cyanide in commercial samples such as pharmaceutical formulations and industrial electrolytic baths.     

Potentiometric titration and differentiation of cyano and nitrito complexes of Ir(III), Pt(II), and Pd(II)

Summary The precipitation titration of the nitrito complexes of Ir(III), Pt(II), and Pd(II) vs. cetylpyridinium chloride is reported. The corresponding cyanide complexes of these precious metals are also precipitated by silver nitrate, which does not react with the nitrito complexes. Differentiation of the 2 types of complexes is, therefore, possible. Sequential estimation of the cyanide complexes and some anions such as bromide, cyanide, and aurocyanide is feasible with silver nitrate.

---

Potentiometrische Titration und Differenzierung von Cyano- und Nitrito-Komplexen von Ir(III), Pt(II) und Pd(II)

---

Work performed under the auspices of the U.S. Department of Energy by the Lawrence Livermore National Laboratory under contract number W-7405-ENG-48     

Solid phase extraction and spectrophotometric determination of silver with 2-(2-quinolylazo)-5-diethylaminophenol as chromogenic reagent.

A new chromogenic reagent, 2-(2-quinolylazo)-5-diethylaminophenol (QADEAP), was synthesized. A sensitive, selective and rapid method has been developed for the determination of microg/L level silver ion based on the rapid reaction of silver(l) with QADEAP and the solid phase extraction of the colored chelate with C18 cartridge. The QADEAP reacts with Ag(l) to form a violet chelate of a molar ratio 1:2 (silver to QADEAP) in pH 3.5-8.0. This chelate was prconcentrated by solid phase extraction with C18 cartridge. An enrichment factor of 100 was achieved. The molar absorptivity of the chelate is 1.30 x 10(5) L mol(-1) cm(-1) at 590 nm in measured solution. Beer's law is obeyed in the range of 0.01-0.6 microg/ml. The relative standard deviation for eleven replicate samples of 0.01 microg/ml is 1.15%. The detection limit is 0.02 microg/L in the original samples. This method was applied to the determination of microg/L level silver ion in water with good results.     

Preconcentration of Cr(III), Co(II), Cu(II), Fe(III) and Pb(II) as calmagite chelates on cellulose nitrate membrane filter prior to their flame atomic absorption spectrometric determinations

A method for the preconcentration and determination of Cr(III), Co(II), Cu(II), Fe(III) and Pb(II) ions by atomic absorption spectrometry has been described. The method was based the collection of metal-calmagite complexes on a soluble cellulose nitrate membrane filter. The detection of the solution was obtained by flame atomic absorption spectrometry (FAAS) after completely dissolving the membrane with 0.5 ml of nitric acid at 80 degrees C. The metal ions were recovered quantitatively at pH 8. Various factors which affect the collection and determination of metal ions such as, type and size of the membrane filter, solvent for dissolution of the species retained on the filter were investigated. The detection limits were varying 0.06 mug l(-1) for Cu to 2.5 mug l(-1) for Cr. An application of the proposed method for analyte ions in mineral and tap water samples was also described with satisfactory results (recoveries >95%, relative standard deviations <10%).     

Influence of Masking Agents on the Color Reactions of Dithizone with Pd(II), Hg(II), and Ag(I) Ions after the Sorption of Their Chloride Complexes on the Fibrous Filled Anion Exchanger AV-17

The influence of masking agents (acetate, thiosulfate, tartrate, and iodide ions; thiourea; and ethylenediaminetetraacetic acid (EDTA)) in a dithizone solution on the complexation of Hg(II), Pd(II), and Ag(I) ions on the solid phase of the fibrous anion exchanger filled with AV-17 was studied. Mercury, palladium, and silver were adsorbed as chloride complexes. The possibility of the simultaneous group determination of the three elements and the selective determination of palladium in the presence of mercury and silver by measuring the diffuse reflection coefficient at two wavelengths (580 and 680 nm, respectively) was demonstrated. A mixture of dithizone with EDTA, acetate, iodide, or thiosulfate can be used for masking concomitant elements. The reaction of palladium with dithizone on the solid phase can be used for the test determination of palladium with the detection limit 0.01 mg/L.     

Separation and determination of metallocyanide complexes of Fe(II), Ni(II) and Co(III) by ion-interaction chromatography with membrane suppressed conductivity detection applied to analysis of oil refinery streams (sour water)

A separation and determination method for the analysis of cyanometallic complexes of Fe(II), Ni(II) and Co(III) was developed to be applied to the analysis of petroleum refinery streams (sour water). Ion-interaction chromatography was used employing an analytical column IonPac NS1 10 microm and a chromatographic system ICS 2500 equipped with a membrane conductivity suppression ASRS ultra 4mm, both supplied by Dionex Corporation. The mobile phase was composed of 2 mmol l(-1) TBAOH, 1 mmol l(-1) Na(2)CO(3), 0.1 mol l(-1) NaCN and ACN (77:23, v/v), flowing at 0.7 ml min(-1). At the optimized conditions, detection limits estimated by the calibration curve parameters and relative standard deviation were: 0.002 mg CNl(-1) and 3.1% for Fe(CN)(6)(4-); 0.003 mg CNl(-1) and 2.5% for Ni(CN)(4)(2-) and 0.003 mg CNl(-1) and 2.8% for Co(CN)(6)(3-). Sour water samples without any pretreatment (except membrane filtration) from a petroleum refinery in Brazil were analyzed successfully by external calibration method.     

Structure and bonding in silver halides. A quantum chemical study of the monomers: Ag(2)X, AgX, AgX(2), and AgX(3) (X = F, Cl, Br, I)

The molecular structure of all silver halide monomers, Ag(2)X, AgX, AgX(2), and AgX(3), (X = F, Cl, Br, I), have been calculated at the B3LYP, MP2, and CCSD(T) levels of theory by using quasirelativistic pseudopotentials for all atoms except fluorine and chlorine. All silver monohalides are stable molecules, while the relative stabilities of the subhalides, dihalides, and trihalides considerably decrease toward the larger halogens. The ground-state structure of all Ag(2)X silver subhalides has C(2)(v)() symmetry, and the molecules can be best described as [Ag(2)](+)X(-). Silver dihalides are linear molecules; AgF(2) has a (2)Sigma(g) ground state, while all of the other silver dihalides have a ground state of (2)Pi(g) symmetry. The potential energy surface (PES) of all silver trihalides has been investigated. Neither of these molecules has a D(3)(h)() symmetric trigonal planar geometry, due to their Jahn-Teller distortion. The minimum energy structure of AgF(3) is a T-shaped structure with C(2)(v)() symmetry. For AgCl(3), AgBr(3), and AgI(3), the global minimum is an L-shaped structure, which lies outside the Jahn-Teller PES. This structure can be considered as a donor-acceptor system, with X(2) acting as donor and AgX as acceptor. Thus, except for AgF(3), in the other three silver trihalides, silver is not present in the formal oxidation state 3.     

Well-defined N-heterocyclic carbene silver halides of 1-cyclohexyl-3-arylmethylimidazolylidenes: synthesis, structure and catalysis in A3-reaction of aldehydes, amines and alkynes

Structurally well-defined N-heterocyclic carbene silver chlorides and bromides supported by 1-cyclohexyl-3-benzylimidazolylidene (CyBn-NHC) or 1-cyclohexyl-3-naphthalen-2-ylmethylimidazolylidene (CyNaph-NHC) were synthesized by reaction of the corresponding imidazolium halides with silver(I) oxide while cationic bis(CyBn-NHC) silver nitrate was isolated under similar conditions using imidazolium iodide in the presence of sodium nitrate. Single-crystal X-ray diffraction revealed a dimeric structure through a nonpolar weak-hydrogen-bond supported Ag-Ag bond for 1-cyclohexyl-3-benzylimidazolylidene silver halides [(CyBn-NHC)AgX](2) (X = Cl, 1; Br, 2) but a monomeric structure for N-heterocyclic carbene silver halides with the more sterically demanding 1-cyclohexyl-3-naphthalen-2-ylmethylimidazolylidene ligand (CyNaph-NHC)AgX (X = Cl, 4; Br, 5). Cationic biscarbene silver nitrate [(CyBn-NHC)(2)Ag](+)NO(3)(-)3 assumed a cis orientation with respect to the two carbene ligands. The monomeric complexes (CyNaph-NHC)AgX 4 and 5 showed higher catalytic activity than the dimeric [(CyBn-NHC)AgX](2)1 and 2 as well as the cationic biscarbene silver nitrate 3 in the model three component reaction of 3-phenylpropionaldehyde, phenylacetylene and piperidine with chloride 4 performing best and giving product in almost quantitative yield within 2 h at 100 °C. An explanation for the structure-activity relationship in N-heterocyclic carbene silver halide catalyzed three component reaction is given based on a slightly modified mechanism from the one in literature.     

1,2-二(2-胺基苯氧基)乙烷银配合物的合成与晶体结构

本文采用配体1, 2-二(邻氨基苯氧基)乙烷(L)分别与AgPF6, AgCF3SO3, AgNO3和AgSbF6 进行配位反应,依次得到了四个配合物1 [Ag2(L)2(PF6)]、2 [Ag2(L)2(CF3SO3)2]、3 [Ag(L)NO3]n 和4 [Ag(L)2SbF6]n,并通过FTIR、元素分析、以及X射线单晶衍射等对配合物的结构与组成进行了表征。单晶衍射结果表明,配合物1和2为双核银(I)配合物,3和4为银(I)的配位聚合物。配合物1具有穴状结构,2经Ag?Ag键桥连两个配体形成扭曲的非平面结构。聚合物3的结构为一维(1D)“之”字链,4具有三维(3D)多孔的结构框架。在四个配合物结构中,相应的抗衡阴离子均未参与Ag(I)进行配位作用。     

Metal ion capillary zone electrophoresis with direct UV detection: Separation of metal cyanide complexes

Mixtures of cyanide complexes of iron(III), copper(I), iron(II), nickel(II), chromium(III), mercury(II), palladium(II), silver(I), cadmium(II), zinc(II), cobalt(II), and cobalt(III) have been separated by capillary zone electrophoresis using a fused silica capillary and 20 mM phosphate buffers containing 1–2 mM sodium cyanide. The complexes were detected by direct UV absorpticn at 214 nm; detection limits are in the mid ppb range for all metals except cadmium and zinc. The different detectability of various metal cyanide complexes enables the application of the method to the analysis of complex matrices such as cyanide plating bath solutions.     

A study on silver nanoparticles-sensitized fluorescence and second-order scattering of the complexes of Tb(III) with ciprofloxacin and its applications

Fluorescence of terbium(III) is sensitized when excited in the presence of ciprofloxacin (CPLX) in the aqueous solution because a Tb(III)-CPLX complex is formed and the maximum fluorescence peak locates at 545 nm. The second-order scattering (SOS) peak at 545 nm also appears for the Tb(III)-CPLX complexes with the excitation wavelength of 272 nm. The intensity at 545 nm obviously increases when the silver nanoparticles are added to the Tb(III)-CPLX system, and the relative intensity is proportional to the concentration of CPLX. Based on this phenomenon, a new method for the determination of CPLX has been developed by using a common spectrofluorometer to measure the intensity of fluorescence and SOS. The intensity is enhanced most by silver nanoparticles at pH 6.0. The calibration graph for CPLX is linear in the range of 3.0 x 10(-9) to 1.0 x 10(-5) mol l(-1). The detection limit is 8.5 x 10(-10) mol l(-1). The method was applied satisfactorily to the determination of CPLX in tablets and capsules. The results show that silver nanoparticles with certain size and concentration can enhance the fluorescence and SOS intensity of the system.     

Simultaneous determination of Cl(-), Br(-), I(-) and F(-) with flow-injection/ion-selective electrode systems

Flow-through ion-selective electrodes were constructed from compressed pellets (8-10 mm thick, 13 mm diameter, 10 tons/cm(2) pressure) of Ag(2)S/AgX (X = Cl(-), Br(-) or I(-)) drilled longitudinally (1.5 mm diameter hole) to be suitable for use in flow-injection analysis. A column of AgCl (5.5 cm long, 2-3 mm i.d.) was included in the Cl(-)-electrode manifold to remove interferences from 10(-4)M Br(-) and 3 x 10(-5)M I(-) and S(2-). A column of amalgamated lead (2-3 cm long, 2-3 mm i.d.) was used in the Br(-) electrode manifold to remove interference from 2 x 10(-5)M I(-), 3 x 10(-5)M S(2-) and 7 x 10(-4)M Cl(-). These columns and the addition of ascorbic acid were not required when I(-) was determined with the iodide electrode. The carrier stream was 0.1M sodium perchlorate (pH 4) at a flow-rate of 0.5 ml/min. The sample pH could be 4-7. Simultaneous determination of Cl(-) and I(-), Cl(-), I(-) and Br(-) and Cl(-), I(-), Br(-) and F(-) ions was possible with combinations of the corresponding electrodes and columns in series and/or parallel in specially designed manifolds. Calibration plots were linear, with almost theoretical slopes, down to 10(-6)M I(-), 5 x 10(-6)M Br(-), 10(-4)M Cl(-) and 5 x 10(-6)M F(-), with precision better than 1%. Sampling rates for single-ion determinations were 72, 102, 90 and 80 per hr for the one-, two-, three- and four-electrode systems respectively. Determinations of these ions in water samples by the recommended procedure and by established batch methods showed no significant difference at the 95% confidence limits in a paired comparison t-test.     

Precipitation-dissolution system for silver preconcentration and determination by flow injection flame atomic absorption spectrometry

In this paper, flame atomic absorption spectrometry was used for the determination of silver in various materials. The proposed preconcentration method is based on the continuous precipitation of silver as p-dimethylaminobenzilidene-rhodanine (PDBR) complex and dissolution of the precipitate with potassium cyanide. EDTA was added to the sample solution to mask large concentrations of Fe(III), Ni(II), Cu(II), Zn(II), Pb(II), Co(II) and Al(III). An enhancement factor of 20 was obtained for a preconcentration time of 3 min, resulting in a sampling frequency of 16 h(-1). The detection limit (3sigma) in the sample solution was 5 ngml(-1). The relative standard deviation at 30 ngml(-1) level was 4.7%. Analytical results obtained for alloy, biological reference material and ore samples analyzed were in good agreement with the certified values and comparable to those obtained with other techniques.     

Simultaneous determination of gallium and indium with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol in cationic micellar medium using derivative spectrophotometry.

A new derivative spectrophotometric method for rapid and selective trace analysis of Ga3+ and In3+ and for their simultaneous determination using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol in a cationic micellar medium is reported. Molar absorptivity and Sandell's sensitivity of 1:1 Ga+ and In3+ complexes at their lambda(max) 553 nm and 558 nm are: 7.22 x 10(4) l mol(-1) cm(-1) and 5.85 x 10(4) l mol(-1) cm(-1), and 0.96 ng cm(-2) and 1.96 ng cm(-2), respectively. Linearity is observed in the concentration range 0.023-0.700 microg ml(-1) for gallium and 0.076-1.52 microg ml(-1) for indium; IUPAC detection limit is 0.012 and 0.035 ng ml(-1), respectively. These metal ions interfere with the determination of each other. However, 0.07-0.70 microg ml(-1) Ga3+ and 0.115-1.150 microg ml(-1) In3+ could be determined simultaneously when present together by the derivative method without any prior separation. The proposed procedures have been successfully applied for the individual and simultaneous determination of gallium and indium in synthetic binary mixtures, standard reference materials and environmental samples.     

Flame atomic absorption spectrometric determination of silver after preconcentration on Amberlite XAD-16 resin from thiocyanate solution

A method of silver preconcentration by using a column containing Amberlite XAD-16 resin and this future determination by a flame AAS after elution is proposed. The effect of the factors such as pH, the nature of complexing agent, sample volume, flow rate, the type and concentration of elution solution on the preconcentration efficiency have been investigated. The influence of some matrix elements on the recovery of silver were also examined. It was found, that the quantitative recovery of thiocyanate complex of silver was obtained from nitric acid solution (pH 2) as 99.20+/-0.07% at the 95% confidence level. A preconcentration factor up to 75 could be obtained. The detection limit of silver was 0.047 mg l(-1). The adsorption of silver onto Amberlite XAD-16 can be formally described by a Langmuir equation with maximum adsorption capacity 4.66 mg g(-1) (0.043 mmol g(-1)). The proposed method was applied to determination of silver in standard alloy with relative error 6.25%.     

Convenient synthesis of 2-(2-pyridyl)-1, 3-diaminopropane,and its copper(II), nickel(II), and cobalt(III) complexes

Summary 2-(2-Pyridyl)-1, 3-propanediol was converted into the diacetate, which was then condensed with phthalimide. The product was hydrolyzed with hydrochloric acid to give 2-(2-pyridyl)-1, 3-diaminopropane. The free amine gave 12 complexes with copper(II), nickel(II), and cobalt(III), which were characterized spectroscopically and magnetically. Features of the amine as a ligand are discussed. A few related complexes were also studied.     

季胺盐型表面活性剂与镉试剂显色反应的研究及应用

在三乙醇胺存在下，季铵盐型表面活性剂溴化十六烷基三甲铵，溴化十二烷基二甲基苄铵和溴化十六烷基吡啶分别与１－（４－硝基苯基）－３－「４－苯基偶氮）苯基」－三氮烯形成离子缔合物显色，吸收光谱红移，离子缔合物；ＮＰ－ＰＡＰＴ与ＤＤＭＢＡＢ来１：２与ＣＴＭＡＢ，ＣＰＢ均为１：３；测定了显色体系的ＣＴＭＡＢ，ＤＤＭＢＡＭ，ＣＰＢ的临界胶束浓度，符合比尔定律的范围，表观摩尔吸光系数δｍａｘ，探讨了微量ＣＴＭＡ     

Ligand displacement, headspace single-drop microextraction, and capillary electrophoresis for the determination of weak acid dissociable cyanide

A new method involving ligand displacement, headspace single-drop microextraction (SDME) with in-drop derivatization and capillary electrophoresis (CE) was developed for the determination of weak acid dissociable (WAD) cyanide. WAD metal-cyanide complexes (Ag(CN)(2)(-), Cd(CN)(4)(2-), Cu(CN)(3)(2-), Hg(CN)(2), Hg(CN)(4)(2-), Ni(CN)(4)(2-) and Zn(CN)(4)(2-)) are decomposed with ligand-displacing reagent and the released hydrogen cyanide is extracted from neutral solution (pH 6.5) with an aqueous microdrop (5 microl) containing Ni(II)-NH(3) as derivatization agent. The hydrogen cyanide extracted reacts with Ni(2+) to form a stable and highly UV absorbing tetracyanonickelate anion which is then determined by CE. Among the three different ligand-displacing reagents (i.e., ethylenediamine, dithizone and polyethileneimine) studied none of the reagents used alone releases cyanide completely from all WAD cyanide complexes. Complete recoveries were obtained by the extraction of WAD cyanide from 0.4 mol l(-1) ethylenediamine chloride buffer (pH 6.5) containing 0.001% (wt) dithizone. Proposed system was applied to determine WAD cyanide in industrial wastewater and river waters samples with spiked recoveries in the range of 95.8-104.7%.     

Structures and Spectroscopy of some Adducts of Coinage Metal(I) Cyanides with ‘Tetrahedral’‐Unidentate‐N‐Bases

Crystallization of copper(I) cyanide from piperidine (‘pip’) solution yields an adduct of CuCN : pip (3 : 4) ratio, as established by a single crystal X‐ray structure determination, which also shows the complex to have a single‐stranded ···Cu(CN)Cu(CN)···spine (C,N scrambled), one‐third of the copper atoms carrying a pair of pip ligands, the others only one. Crystallization of silver(I) cyanide from piperidine (‘pip’) or cyclohexylamine (‘CyNH₂’) solutions yields adducts of the unusual AgX : unidentate‐N‐base (1 : 2) stoichiometry. The CyNH₂ adduct is, unusually for cyanide complexes of this type, mononuclear with a trigonal planar silver atom, [(NC)Ag(H₂NCy)₂], the AgCN component lying along the intersection of two crystallographic mirror planes which bisect and relate the H₂NCy ligands (Ag‐C, N 2.067(3), 2.335(2) Å; N‐Ag‐N, C 80·80(6), 139.60(4)°). In the pip adduct, the immediate silver atom environment is also three‐coordinate (Ag‐C; N, N 2.080(1); 2.288, 2.443(1) Å; N‐Ag‐N 88·34(4), N‐Ag‐C 144.47(4), 125.07(4), (Σ357.₉°) perturbed toward two‐coordination, but the silver atom environment geometry is further perturbed from planarity by the parallel approach of an inversion‐related molecule (Ag···C′ 2.926(1) Å (Ag···Ag′ 3.1842(2)°) forming a loose, albeit still discrete, dimer. Key features in the IR spectra of the above compounds and of AgCN : pip (1 : 1) and CuCN : CyNH₂ (2 : 3) are assigned and discussed in terms of the structures or of proposed structures in the case of the latter two adducts. The structure of [ClAg(pip)₃], adventitiously obtained, is also described (Ag‐Cl 2.471(3); Ag‐N 2.147(13), 2.188(7) (x2) Å; Cl‐Ag‐N 96.1(3), 98.5(2), N‐Ag‐N 116.3(2) (x2), 122.1(3)°).     

Anion-exchange chromatography of metal cyanide complexes with gradient separation and direct UV detection

In the regulatory analysis of water samples, cyanide content is usually expressed in various forms as free cyanide, total cyanide, weak-acid dissociable cyanide, available cyanide, and cyanide amenable to chlorination. Concentration of individual metal cyanide complex, not furnished in any of these methods, is useful in meaningful assessment of toxicity due to cyanide. In the present work, two macroporous anion-exchange columns, having high and intermediate hydrophobicity, were evaluated to achieve separation of cyano complexes of silver, iron, gold, copper, nickel, and cobalt. On the QS-Al SC column, of high hydrophobicity, the monovalent cyano complexes of silver and gold eluted last while the multivalent cyano complexes, e.g. iron and copper, eluted early. It is suggested that the retention order on this column is due to relative hydrophobicity of the metal cyanide complex, and its affect on ion exchange. In contrast, on the QS-A2 SC column of intermediate hydrophobicity, with the exception of cyano complex with Fe, the separation of the cyano complexes of five other metals closely followed an anion-exchange mechanism. Under gradient conditions, the six metal cyanide complexes were well resolved on the QS-A2 SC column and the method with direct UV detection at 215 nm was accurate (spike recovery of 99.8-118.8%) and precise (RSD of 1.0-2.6%).