Phase transition of RbH<Subscript>2</Subscript>PO<Subscript>4</Subscript> and its composite with SiO<Subscript>2</Subscript> studied by thermal analysis

The phase transition at T _p (~109 °C) of RbH₂PO₄ and its composite with SiO₂ has been investigated by thermal analysis here. In the case of neat RbH₂PO₄, there is a linear relationship between endothermic peak temperature (T _m) and square root of heating rate (Φ ^1/2), from which the onset temperature of phase transition can be determined. Besides, Kissinger method and another calculation method were employed to obtain the activation energy of phase transition. The detailed deduction process was presented in this paper, and the estimated activation energies are E ₁ ≈ 126.3 kJ/mol and E ₂ ≈ 129.2 kJ/mol, respectively. On the other hand, the heterogeneous doping of RbH₂PO₄ with SiO₂ as dopant facilitates its proton conduction and leads to the disappearance of jump in conductivity at T _p. The heats of transition in the composites decrease gradually with increasing the molar fraction of SiO₂ additives. In the cooling process, a new and broad exothermic peak appeared between ~95 and ~110 °C, and its intensity also changes with the SiO₂ amount. These phenomena might be related to the formation of amorphous phase of RbH₂PO₄ on the surface of SiO₂ particles due to the strong interface interaction.     

Microstructure of SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> hybrid electrospun nanofibers and their application in dye degradation

SiO₂/TiO₂ hybrid nanofibers were prepared by electrospinning and applied for photocatalytic degradation of methylene blue (MB). The phase structure, specific surface area, and surface morphologies of the SiO₂/TiO₂ hybrid nanofibers were characterized through thermogravimetry (TG), X-ray diffraction (XRD) analysis, Brunauer–Emmett–Teller (BET) analysis, scanning electron microscopy (SEM), etc. XRD measurements indicated that doping of silica into TiO₂ nanofibers can delay the phase transition from anatase to rutile and decrease the grain size. SEM and BET characterization proved that silica doping can remarkably enhance the porosity of the SiO₂/TiO₂ hybrid nanofibers. The MB adsorption capacity and photocatalytic activity of the SiO₂/TiO₂ hybrid nanofibers were distinguished experimentally. It was found that, although increased silica doping content could enhance the MB adsorption capacity, the intrinsic photocatalytic activity gradually dropped. The SiO₂ (10 %)/TiO₂ composite nanofibers exhibited the highest MB degradation rate, being superior to SiO₂ (20 %)/TiO₂ or pure TiO₂.     

Study on chemisorption of H<Subscript>2</Subscript>, O<Subscript>2</Subscript>, CO and C<Subscript>2</Subscript>H<Subscript>4</Subscript>on Pt-Ag/SiO<Subscript>2</Subscript>catalysts by microcalorimetry and FTIR

Adsorption microcalorimetry has been employed to study the interaction of ethylene with the reduced and oxidized Pt-Ag/SiO₂catalysts with different Ag contents to elucidate the modified effect of Ag towards the hydrocarbon processing on platinum catalysts. In addition, microcalorimetric adsorption of H₂, O₂, CO and FTIR of CO adsorption were conducted to investigate the influence of Ag on the surface structure of Pt catalyst. It is found from the microcalorimetric results of H₂and O₂adsorption that the addition of Ag to Pt/SiO₂leads to the enrichment of Ag on the catalyst surface which decreases the size of Pt surface ensembles of Pt-Ag/SiO₂catalysts. The microcalorimetry and FTIR of CO adsorption indicates that there still exist sites for linear and bridged CO adsorption on the surface of platinum catalysts simultaneously although Ag was incorporated into Pt/SiO₂. The ethylene microcalorimetric results show that the decrease of ensemble size of Pt surface sites suppresses the formation of dissociative species (ethylidyne) upon the chemisorption of C₂H₄on Pt-Ag/SiO₂. The differential heat vs. uptake plots for C₂H₄adsorption on the oxygen-preadsorbed Pt/SiO₂and Pt-Ag/SiO₂catalysts suggest that the incorporation of Ag to Pt/SiO₂could decrease the ability for the oxidation of C₂H₄.     

Spectroscopic investigation of structure and mechanism of proton conductivity CsHSO<Subscript>4</Subscript> and composites CsHSO<Subscript>4</Subscript>/SiO<Subscript>2</Subscript>

IR and RS spectra, structural, thermodynamical and transport properties of CsHSO₄ and CsHSO₄/SiO₂ composites have been investigated. It is shown that CsHSO₄ is stabilized in composites in phase II (monoclinic modification), which turns into amorphous state with increasing silicon dioxide content. A formation of disordered highly conducting states of CsHSO₄ in composites at the temperatures noticeably lower than superionic phase transition was stated. Bond length equalization in sulfate-ions, weakening of hydrogen bond system, and as a result easier proton transfer in composites in comparison with pure salt take place in these conducting states. Mechanism for formation of composites and their proton conductivity is proposed.     

Effect of Er<Subscript>2</Subscript>O<Subscript>3</Subscript> on thermal stability of oxyfluoride glass

Glasses have been synthesized in the system SiO₂–Al₂O₃–Na₂O–AlF₃–LaF₃–Er₂O₃. A base glass (in mol% 67SiO₂–9Al₂O₃–20Na₂O–Al₂F₆–3La₂F₆) was modified by 0.5, 0.75, 1, 1.25, 1.5, 2 and 5 mol% Er₂O₃, respectively. Glasses were prepared by conventional fusion method from 20 g batches. The glass transition temperature (T _g), the jump-like changes of the specific heat (ΔC _p) accompanying the glass transition and the enthalpy of crystallization (ΔH) were calculated. DTA measurements clearly reveal that the increase of the Er₂O₃ content in the glass changes the effects of crystallization and diminishes the thermal stability of the glassy network. In the same time the changes in the transition temperature are observed. The formation of NaLaF₄ and Na_1.45La_9.31(SiO₄)₆(F_0.9O_1.1) as a main phase was confirmed. The diminishing of the thermal stability was connected with erbium which incorporated into Na_1.45La_9.31(SiO₄)₆(F_0.9O_1.1) structure.     

The effect of PO<Subscript>2,5</Subscript> and AlO<Subscript>1,5</Subscript> additions on structural changes and crystallization behavior of SiO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> sol-gel derived glasses and thin films

SiO₂-TiO₂-PO_2,5 (STP) and SiO₂-TiO₂-AlO_1,5 (STA) glasses were prepared by sol-gel processing. Their infrared absorption spectra (IR), differential thermal analysis curves (DTA) and X-ray diffraction patterns (XRD) have been recorded. In the SiO₂-TiO₂ system, the chemical homogeneity of the sol-gel glass could be evaluated by the relative concentration of Si-O-Ti heterocondensation comparing to Si-O-Si homocondensation. For the STA system, a gradual decrease of the Si-O-Ti/Si-O-Si band ratio (based on IR spectra) with the addition of Al₂O₃ is observed, with the simultaneous formation of Si-O-Al and Ti-O-Al bounds, i.e Al₃ ⁺ ions are dissolved in the SiO₂-TiO₂ glass matrix and do not promote glass-in-glass phase-separation in the composition range of 0–15 mol% AlO_1.5. In the STP system, on the other hand, P=O bond IR stretch in the ternary glasses indicates that P=O free PO₂O_2/2 ⁻ tetrahedra are formed, rather than the double bonded POO_3/2 tetrahedra that usually occur in binary SiO₂-P₂O₅ glasses. It can be concluded that SiO₂-TiO₂-P₂O₅ glass separates into a SiO₂-rich phase and a TiO₂(P₂O₅)-rich phase. During heat-treatment in STA system only anatase precipitates, even at T ~ 1,000 °C, while in for STP, anatase (TiO₂) or (TiO)₂P₂O₇ (TOP) crystals precipitate at ~600 °C, depending on the P₂O₅ concentration. The major crystal phase, cristobalite, precipitated at ~1,000 °C and at ~1,200 °C, the P-containing phase melts.     

Phase relationships in the SiO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> system

Phase equilibria in a miscibility gap of the SiO₂-TiO₂ system were studied. A visual polythermal analysis and annealing of samples were performed in a Galakhov microfurnace. The microstructure and composition of the obtained samples were investigated by scanning electron microscopy and electron probe microanalysis. A critical analysis of the experimental data was made. Thermodynamically optimized based on the sub-regular solution model, a phase diagram of the SiO₂-TiO₂ system was constructed.     

Preparation and optical characterization of catalyst free SiO<Subscript>2</Subscript> sonogel hybrid materials

The synthesis of sol-gel materials induced by ultrasonic irradiation (sonolysis) is implemented as an alternative method for the fabrication of highly pure organic-inorganic composites with good monolithic, mechanical and optical properties. Ultrasonic irradiation, instead of commonly used basic- or acidic-catalyst was used to produce acoustical cavitation within the liquid H₂O/tetraethyl-ortosilicate (TEOS) reactants. This procedure forms a hydrolyzed-TEOS colloidal dispersion (sol) which produces, after drying, a highly pure SiO₂ network. The resulting SiO₂ glass exhibits high porosity and allows the inclusion of several organic compounds in the colloidal sol-state. Novel, optical active synthesized liquid crystalline (LC)-azo-compounds, bent shaped mesogens, cis- and trans-poly(1-ethynylpyrene)s, as well as fullerene (C₆₀) spheres and classical organic dyes were successfully incorporated as dopant agents within the novel catalyst free (CF) SiO₂-sonogel host matrix. Absorption and fluorescence spectroscopy studies were carried out in order to characterize the optical performance of both the CF-sonogel and several hybrid composites The pulsed laser photoacoustic technique (LPAT) was implemented to determine thermodynamic phase transitions of LC-based hybrids and laser induced damage (photo-degradation) in dye-based composites. Finally, comparative morphology studies between undoped reference samples and some doped composites were performed by Atomic Force Microscopy (AFM), where an optimal TEOS/dopant concentration ratio, to obtain good mechanical properties among the studied samples, has been found.     

Structures and phase transitions in (K<Subscript>1-x</Subscript>Rb<Subscript>x</Subscript>)<Subscript>2</Subscript>SeO<Subscript>4</Subscript>

Summary The phase diagram of the mixed crystal (K_1-xRb_x)₂SeO₄ was determined by means of thermal analysis and neutron scattering experiments. The hexagonal to orthorhombic phase transition line exists for any x. The normal-incommensurate phase transition temperature decreases continuously with increasing Rb content. However, the incommensurate-commensurate phase transition was not observed except for K₂SeO₄. According to the clear softening of the Σ₂- Σ ₃ phonon branches and the finite frequency at 0 K for x>0.34, an existence of the hypothetical phase transition was confirmed.     

The synthesis,structure, and electrochemical properties of Li<Subscript>2</Subscript>FeSiO<Subscript>4</Subscript>-based lithium-accumulating electrode material

Different approaches to synthesis of Li₂FeSiO₄-based electrode materials for lithium intercalation, using low-cost and abundant Li-, Si-, and Fe-containing parent substances, are discussed. XRD, SEM, and a laser-diffraction analyzer of particle size were used for structure and morphology characterization of the composite electrode materials. Li₂FeSiO₄ was shown to be the main lithium-accumulating crystalline phase; minor LiFeO₂ and Li₂SiO₃ admixtures are also present. The material microparticles’ average size was shown to vary from tenths of micrometer to 1 μm. Larger objects sized ca. 2–4 μm are the microparticles’ agglomerates. The material electrochemical properties were studied by dc chronopotentiometry (galvanostatic charging–discharging) and cyclic voltammetry with potential linear sweeping. The initial reversible cycled capacity of the best samples is 170 mA h/g. The anodic and cathodic processes manifest obvious hysteresis caused by the presence of several different lithium ion energy states in the material; the transition between the states is kinetically hindered. The dependences of the specific capacity and its stability under cycling on the current load and the conductive carbon component content in the composite were elucidated.     

Solid-phase synthesis of intermetallic compounds Al<Subscript>13</Subscript>Co<Subscript>4</Subscript>, Al<Subscript>13</Subscript>Fe<Subscript>4</Subscript>, and Al<Subscript>13</Subscript>Co<Subscript>2</Subscript>Fe<Subscript>2</Subscript>

Intermetallic compounds Al₁₃Co₄, Al₁₃Fe₄, and Al₁₃Co₂Fe₂ were obtained by solid-phase synthesis in air at temperatures below 600°C using precursor metals subjected to mechanochemical preactivation. The phase composition of the synthesized aluminides and composites Al₁₃Co₄/SiO₂ and Al₁₃Fe₄/SiO₂ was analyzed.     

Specific heat on Sr<Subscript>2</Subscript>Nb<Subscript>2</Subscript>O<Subscript>7</Subscript> and Sr<Subscript>2</Subscript>Ta<Subscript>2</Subscript>O<Subscript>7</Subscript>

Summary Specific heats on the single crystals of Sr₂Nb₂O₇, Sr₂Ta₂O₇ and (Sr_1-xBa_x)₂Nb₂O₇ were measured in a wide temperature range of 2-600 K. Heat anomalies of a λ-type were observed at the incommensurate phase transition of T_INC (=495 K) on Sr₂Nb₂O₇ and at the super-lattice phase transition of T_SL (=443 K) on Sr₂Ta₂O₇; the transition enthalpies and the transition entropies were estimated. Furthermore, a small heat anomaly was observed at the low temperature ferroelectric phase transition of T_LOW (=95 K) on Sr₂Nb₂O₇. The transition temperature T_LOW decreases with increasing Ba content x and it vanishes for samples of x>2%.     

Moisture and solvent responsive cellulose/SiO<Subscript>2</Subscript> nanocomposite materials

Water responsive SiO₂/cellulose nanocomposite hydrogels and films were constructed, for the first time, by dispersing SiO₂ nanoparticles into cellulose solution in LiOH/urea solvent, and then by crosslinking with epichlorohydrin or regeneration in coagulation bath, respectively. The cellulose nanocomposite materials were characterized by Field emission scanning electron microscopy, FTIR, dynamic rheology, wide angle X-ray diffraction and mechanical test. The SiO₂/cellulose nanocomposites at wet state or in water displayed unique behaviors, showing higher light transmittance than those before contacting with water. The results revealed that strong hydrogen-bonding interaction among water, cellulose and SiO₂ led the good dispersion of SiO₂ nanoparticles in the cellulose matrix. The incorporation of SiO₂ nanoparticles improved the transmittance and mechanical strength of the cellulose hydrogels, and also enhanced the mechanical strength of the films. Especially, the cellulose/SiO₂ nanocomposite films were milky at dry state, and changed to transparent after being soaked in water, different from the cellulose film without the SiO₂ nanoparticles. In our findings, SiO₂ and cellulose with water could form strong hydrogen bonding to create a homogenous network structure. The cellulose/SiO₂ composite as a smart material exhibited moisture and solvent responsiveness, showing potential applications in moisture detection.     

UV-Assisted Fabrication of Reduced Graphene Oxide Doped SiO<Subscript>2</Subscript>@TiO<Subscript>2</Subscript> Nanocomposites as Efficient Photocatalyst for Photodegradation of Rhodamine B

The core-shell nanostructure materials have gained great interests because of its excellent photocatalytic properties and promising applications in several fields. In this work, we prepared the core-shell SiO₂@TiO₂ nanocomposites by the versatile kinetics-controlled coating method. The graphene oxide (GO) was further reduced over SiO₂@TiO₂ using UV-assisted photocatalytic reduction method. The physicochemical properties of the as-prepared SiO₂@TiO₂/RGO nanocomposites were characterized by SEM, XRD, BET, EDS, and FTIR. Results showed that, TiO₂ was mainly composed of anatase phase with high crystallinity. Their photocatalytic activities were examined by the degradation of Rhodamine B (RhB) under UV light irradiation. The presence of RGO obviously improved the adsorption ability and photodegradation performance of the composites to RhB. The degradation kinetics of RhB can be described by the pseudo-first-order model. The optimum mass ratio of SiO₂@TiO₂ to RGO in the composite was 1/0.05 and the rate constant was about 4 times greater than that of the SiO₂@TiO₂.     

Solution,Solid-State Two Step Synthesis and Optical Properties of ZnO and SnO<Subscript>2</Subscript> Nanoparticles and Their Nanocomposites with SiO<Subscript>2</Subscript>

Nanostructure luminescent ZnO and SnO₂ materials are prepared by a two-step solid-state method based on the solution preparation of the macromolecular precursors ZnCl₂·Chitosan and SnCl₂·Chitosan having different ratios (1:1, 1:5 and 1:10), their pyrolysis under air at 800 °C. The pyrolytic ZnO and SnO₂ nanomaterials show a dependence of the particle size, morphology and luminescent properties with the ratio [metal/polymer] in the MCl₂·Chitosan precursors. Thus, ZnO semiconductor materials exhibit luminescence spectra with several emission at 440 nm corresponds to a radiative transition of an electron from the shallow donor level of oxygen vacancies, and the zinc interstitial, to the valence band. On the other hand, the photoluminescence spectrum of the nanostructured SnO₂ shows an intense blue luminescence at a wavelength of 420 nm which may be attributed to oxygen-related defects that have been introduced during the growth process of the nanoparticles. Additionally, whereas SnO₂ was successfully incorporated into SiO₂ structure (SnO₂//SiO₂) by pyrolysis of solid-state mixtures of the precursors SnCl₂·Chitosan in the presence of SiO₂, the same reaction carried out with ZnCl₂·Chitosan precursors led to a mixture of Zn₂SiO₄ and SiO₂. Thus, this new methodology yields nanostructured semiconductor materials, ZnO and SnO₂, suitable for optoelectronic and sensor solid-state devices.     

On the nature of the processes occurring in silver doped SiO<Subscript>2</Subscript> films under heat treatment

The processes taking place on air-heating of SiO₂−Ag⁺ films and xerogels produced from the SiO₂ sols of different pH (3.7 or 9.5) were investigated. Silver nanoparticles 10–40 nm in size tolerant to oxidation at temperatures above 600 °C were found to be formed in the systems whatever the pH value of the starting sol. SiO₂ crystallization giving the cristobalite phase in the temperature range from 500 to 800 °C was shown to proceed only in the films produced from the acidic sol, while in those formed from the alkali one SiO₂ remained amorphous. A mechanism by which the formation of Ag nanoparticles and the cristobalite phase occurs in the films at the oxidative conditions is suggested.     

Electrochemical determination of 5-hydroxytryptamine using mesoporous SiO<Subscript>2</Subscript> modified carbon paste electrode

A mesoporous SiO₂ was synthesized according to the published work, and then used to modify the carbon paste electrode (CPE). The electrochemical behaviors of 5-hydroxytryptamine (5-HT) at the bare CPE and the mesoporous SiO₂ modified CPE were compared. Owing to the huge surface area, unique mesopores and strong adsorptive ability, the oxidation signal of 5-HT at the mesoporous SiO₂ modified CPE greatly increased, compared with that at the bare CPE. This clearly suggests that the mesoporous SiO₂ modified electrode shows efficient and remarkable enhancement effect towards 5-HT. Based on this, a sensitive, rapid and convenient electrochemical method was developed for the determination of 5-HT after optimizing the experimental parameters such as supporting electrolyte, content of mesoporous SiO₂ as well as accumulation time. The linear range is from 2.0 × 10⁻⁷ to 1.5 × 10⁻⁵ mol/l, and the limit of detection is as low as 8.0 × 10⁻⁸ mol/l after 2-min accumulation. The relative standard deviation (RSD) for 10 mesoporous SiO₂ modified CPEs is evaluated to be 6.7%. Finally, this novel method was successfully used to determine 5-HT in human blood serums.     

Microstructure and Photocatalytic Property of SiO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> Under Various Process Condition

Nanophase silica-titania particles were prepared by two different synthetic routes, namely, sol–gel and hydrothermal processing. The crystallinity and crystallographic phases, particle size and surface area of the materials were controlled by varying the calcination temperature, and/or the ratio of Si to Ti. It was determined by XRD that the crystallite sizes of SiO₂-TiO₂ prepared by sol–gel and hydrothermal processing decreased from 11 to 6 nm and 12 to 9 nm, respectively, as the mole fraction of silica was increased from 0.1 to 0.4. It is proposed that the presence of the amorphous silica suppresses the growth of anatase TiO₂ grains and their phase transformation to rutile. The photocatalytic decomposition rate of 1,4-dichlorobenzene (DCB) in aqueous solution with the sol–gel derived SiO₂-TiO₂ powder prepared at 750 °C was about 10 ± 5% higher than that observed with Degussa P25, whereas the SiO₂-TiO₂ samples prepared by hydrothermal processing at 250 °C showed a slightly lower decomposition rate than P25.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Polymorphic Mn/W/Na(K,Rb,Cs)/SiO<Subscript>2</Subscript> catalysts for oxidative coupling of methane

The phase composition of Mn/W/Na(K,Rb,Cs)/SiO₂ composites-catalysts was determined by X-ray diffraction. Polymorphic transformations involving tridymite (a SiO₂-based nonstoichiometric crystalline phase) were shown to be a reason for the high catalytic activity of Mn/W/Na(K,Rb,Cs)/SiO₂ in heterogeneous oxidative coupling of methane.