Structural characterization and oxidative dehydrogenation activity of V2O5/Ce(x)Zr(1-x)O2/SiO2 catalysts

The thermal stability of a nanosized Ce(x)Zr(1-x)O2 solid solution on a silica surface and the dispersion behavior of V2O5 over Ce(x)Zr(1-x)O2/SiO2 have been investigated using XRD, Raman spectroscopy, XPS, HREM, and BET surface area techniques. Oxidative dehydrogenation of ethylbenzene to styrene was performed as a test reaction to assess the usefulness of the VOx/Ce(x)Zr(1-x)O2/SiO2 catalyst. Ce(x)Zr(1-x)O2/SiO2 (1:1:2 mol ratio based on oxides) was synthesized through a soft-chemical route from ultrahigh dilute solutions by adopting a deposition coprecipitation technique. A theoretical monolayer equivalent to 10 wt % V2O5 was impregnated over the calcined Ce(x)Zr(1-x)O2/SiO2 sample (773 K) by an aqueous wet impregnation technique. The prepared V2O5/Ce(x)Zr(1-x)O2/SiO2 sample was subjected to thermal treatments from 773 to 1073 K. The XRD measurements indicate the presence of cubic Ce0.75Zr0.25O2 in the case of Ce(x)Zr(1-x)O2/SiO2, while cubic Ce0.5Zr0.5O2 and tetragonal Ce0.16Zr0.84O2 in the case of V2O5/Ce(x)Zr(1-x)O2/SiO2 when calcined at various temperatures. Dispersed vanadium oxide induces more incorporation of zirconium into the ceria lattice, thereby decreasing its lattice size and also accelerating the crystallization of Ce-Zr-O solid solutions at higher calcination temperatures. Further, it interacts selectively with the ceria portion of the composite oxide to form CeVO4. The RS measurements provide good evidence about the dispersed form of vanadium oxide and the CeVO4 compound. The HREM studies show the presence of small Ce-Zr-oxide particles of approximately 5 nm size over the surface of amorphous silica and corroborate with the results obtained from other techniques. The catalytic activity studies reveal the ability of vanadium oxide supported on Ce(x)Zr(1-x)O2/SiO2 to efficiently catalyze the ODH of ethylbenzene at normal atmospheric pressure. The remarkable ability of Ce(x)Zr(1-x)O2 to prevent the deactivation of supported vanadium oxide leading to stable activity in the time-on-stream experiments and high selectivity to styrene are other important observations.     

Photochemical CO2 splitting by metal-to-metal charge-transfer excitation in mesoporous ZrCu(I)-MCM-41 silicate sieve

Binuclear redox sites consisting of a Zr oxo-bridged to a Cu(I) center have been obtained on the pore surface of MCM-41 silicate sieve by a stepwise grafting procedure, along with isolated metal centers. The bimetallic site features a Zr(IV)-O-Cu(I) to Zr(III)-O-Cu(II) metal-to-metal charge-transfer (MMCT) absorption extending from the UV region to about 500 nm. The Zr-O-Cu linkage is revealed by a Cu(I)-O infrared stretch mode at 643 cm-1. Irradiation of the MMCT chromophore of ZrCu(I)-MCM-41 loaded with 1 atm of CO2 gas at room temperature resulted in growth of CO (2150 cm-1) and H2O (1600 cm-1). Photolysis experiments using 13CO2 and C18O2 demonstrate that carbon monoxide and the oxygen atom of the water product originate from CO2. This indicates splitting of the CO2 by the excited MMCT moiety to CO and a surface OH radical, followed by trapping of the products at Cu(I) centers (OH is reduced to H2O). This is the first observation of CO2 photoreduction at a binuclear MMCT site at the gas-solid interface.     

Interaction of Keggin anions of 12-tungstophosphoric acid with Ce(x)Zr(1-x)O2 solid solutions

The interaction of 20 wt% 12-tungstophosphoric acid with Ce(x)Zr(1-x)O(2) solid solutions has been studied by PXRD, FTIR, FT-Raman, H(2)-TPR, NH(3)-TPD, diffuse reflectance UV-vis-NIR, and (31)P MAS NMR techniques. The study indicates that the Keggin anions are attached to Lewis metal ion centres and anion vacancies on Ce(x)Zr(1-x)O(2) supports through WO terminal bonds. The Keggin units at the interface are chemically perturbed as indicated by non-intrinsic IR bands observed at 958 cm(-1) (WO(ter) bond), and 1052, 1102 cm(-1) (PO bond). NH(3)-TPD shows that the Keggin anions fixed to Lewis sites and/or oxygen ion vacancies decrease the ammonia uptake on Ce(x)Zr(1-x)O(2) solid solutions. H(2)-TPR shows modified redox behaviour of Ce(x)Zr(1-x)O(2) solid solutions due to the simultaneous reduction of ceria, decomposition of Keggin anions and the reduction of WO(3). The broadening of (31)P MAS NMR and DR-UV-vis-NIR spectra demonstrate the existence of chemical interactions between the Keggin anions and Ce(x)Zr(1-x)O(2) supports.     

Ce-doped ZnO (Ce(x)Zn(1-x)O) becomes an efficient visible-light-sensitive photocatalyst by co-catalyst (Cu2+) grafting

We have fabricated an efficient visible-light-sensitive Cu(2+)-grafted Ce-doped ZnO photocatalyst (Cu(2+)-Ce(x)Zn(1-x)O) by adopting a metal ion doping and co-catalyst modification. Impurity states were formed below the conduction band (CB) edge in Ce(x)Zn(1-x)O, and these impurity states induce the visible-light absorption. Ce(x)Zn(1-x)O without a Cu(2+)-co-catalyst showed negligible visible-light activity due to the low reduction power of electrons in impurity levels. Surprisingly, Cu(2+)-modification over Ce(x)Zn(1-x)O drastically increased its visible-light activity. Excited electrons in impurity states can transfer to the Cu(2+)-ions on the surface and form Cu(2+)/Cu(+) redox couples, which cause the efficient oxygen reduction through a multi-electron reduction process. One of the striking features of the present study is that the metal doped semiconductors which were inactive due to their impurity states become efficient visible-light photocatalysts upon co-catalyst modification. The successful strategy used here for designing a highly active visible-light photocatalyst would provide numerous opportunities to develop an efficient metal-ion based visible-light photocatalyst.     

Comprehensive interpretation of a substitution effect on an order-disorder phase transition in A(1-x)MxW2O(8-y) (A = Zr, Hf; M = trivalent cations) and other ZrW2O8-based solid solutions

Hf(1-x)Lu(x)W(2)O(8-y) solid solutions up to x = 0.04, based on a negative thermal expansion material HfW(2)O(8), were synthesized by a solid state reaction method. X-ray diffraction experiments of these solid solutions from 90 to 560 K indicated thermal contraction with increasing temperature. Temperatures of order-disorder phase transition (T(trs)) associated with the orientation of WO(4) tetrahedra were determined from disappearance of a characteristic diffraction peak (310). The T(trs) of the solid solutions drastically decreased with increasing Lu content. Saturated order parameters (eta(s)) associated with the orientational order of the WO(4) pairs were estimated from the characteristic diffraction peak at sufficient low temperature. These behaviors of Hf(1-x)Lu(x)W(2)O(8-y) are consistent with those of Zr(1-x)M(x)W(2)O(8-y) (M = Sc, Y, In, Lu). The drastic suppression of T(trs) in Hf(1-x)Lu(x)W(2)O(8-y) can be interpreted in the framework of a model proposed for Zr(1-x)M(x)W(2)O(8-y), which states the existence of a local nanoregion including the WO(4) pairs having the frozen-in orientational disorder. To understand the substitution effect on the order-disorder phase transition comprehensively, classification based on the saturated order parameter eta(s) of the phase transition of AW(2)O(8) (A = Hf, Zr)-based solid solutions was carried out and discussed.     

掺杂助剂Ce和Zr的Ni/Al2O3催化剂的X光电子能谱分析

以Na2CO3为沉淀剂,在pH 9.0的沉淀条件下,采用并流沉淀法制备了Ni/Al2O3、Ni/CeO2-Al2O3、Ni/ZrO2-Al2O3和Ni/ZrO2-CeO2-Al2O34种催化剂,催化剂中Ni负载量(质量分数)为10%。采用XPS表征手段及常压固定床反应器对催化剂进行活性评价,考察了助剂Ce和Zr及二者的协同作用对Ni基催化剂表面物种结合能的影响以及对甲烷自热重整制氢反应性能的影响。结果表明,助剂Ce和Zr的添加及二者的协同作用对Ni基催化剂表面各物种的结合能均有一定的影响,结合评价结果可知,Ce和Zr二者的协同作用对Ni基催化剂的催化性能提高最大。     

Pt/Ce0.6Zr0.4O2催化剂在水煤气变换反应中的电导研究

采用浸渍法制备了不同载体(Ce0.6Zr0.4O2,CeO2和ZrO2)负载的Pt基水煤气变换反应(WGSR)催化剂, 并对其进行了活性评价. 利用X射线衍射(XRD), 程序升温还原(TPR)和原位电导等技术对样品进行了表征. 结果表明, Ce0.6Zr0.4O2固溶体具有比CeO2更高的氧转移能力, 因此促进了Pt/Ce0.6Zr0.4O2催化剂的WGSR活性.     

Surface stabilized nanosized Ce(x)Zr(1-x)O(2) solid solutions over SiO(2): characterization by XRD, Raman, and HREM techniques

Ce(x)Zr(1)(-)(x)O(2) solid solutions deposited over silica surface were investigated by X-ray diffraction (XRD), Raman spectroscopy (RS), and high-resolution transmission electron microscopy (HREM) techniques in order to understand the role of silica support and the temperature stability of these composite oxides. For the purpose of comparison, an unsupported Ce(x)Zr(1)(-)(x)O(2) was also synthesized and subjected to characterization by various techniques. The Ce(x)Zr(1)(-)(x)O(2)/SiO(2) (CZ/S) (1:1:2 mole ratio based on oxides) was synthesized by depositing Ce(x)Zr(1)(-)(x)O(2) solid solution over a colloidal SiO(2) support by a deposition precipitation method and unsupported Ce(x)Zr(1)(-)(x)O(2) (CZ) (1:1 mole ratio based on oxides) was prepared by a coprecipitation procedure, and the obtained catalysts were subjected to thermal treatments from 773 to 1073 K. The XRD measurements disclose the presence of cubic phases with the composition Ce(0.75)Zr(0.25)O(2) and Ce(0.6)Zr(0.4)O(2) in CZ samples, while CZ/S samples possess Ce(0.75)Zr(0.25)O(2), Ce(0.6)Zr(0.4)O(2), and Ce(0.5)Zr(0.5)O(2) in different proportions. The crystallinity of these phases increased with increasing calcination temperature. The cell a parameter estimations indicate contraction of ceria lattice due to the incorporation of zirconium cations into the CeO(2) unit cell. Raman measurements indicate the presence of oxygen vacancies, lattice defects, and displacement of oxygen ions from their normal lattice positions in both the series of samples. The HREM results reveal, in the case of CZ/S samples, a well-dispersed nanosized Ce-Zr-oxides over the surface of amorphous SiO(2). The structural features of these crystals as determined by digital diffraction analysis of experimental images reveal that the Ce-Zr-oxides are mainly in the cubic geometry and exhibit high thermal stability. Oxygen storage capacity measurements by a thermogravimetric method reveal a substantial enhancement in the oxygen vacancy concentration of CZ/S sample over the unsupported CZ sample.     

Ce0.5+xZr0.4-xLa0.1O2-Al2O3催化剂催化燃烧柴油车碳烟

采用共沉淀法制备了系列Ce_0.5+xZr_0.4-xLa_0.1O₂-Al₂O₃催化剂, 其中0≤x≤0.4且Ce_0.5+xZr_0.4-xLa_0.1O₂与Al₂O₃的质量比为1:1. 考察了该系列催化剂对柴油车排放碳烟的催化燃烧性能, 并用低温N2吸附-脱附、X射线衍射(XRD)、X射线光电子能谱(XPS)、氢气程序升温还原(H₂-TPR)和氧气程序升温脱附(O₂-TPD)等手段对催化剂进行了表征. 研究结果表明该系列催化剂均形成了具有立方萤石结构的固溶体. 当x=0.2时, Ce³⁺离子在催化剂表面有一定的富集, 此时催化剂具有最大的β氧脱附峰和最好的表面还原性能, 同时具有良好的催化碳烟氧化活性, 碳烟在该催化剂的起燃温度为360 °C, 具有较好的应用前景.     

单相Ce0.5Zr0.5O2立方固溶体的高压高温合成

以化学沉淀法制备的 Ce O2 和 Zr O2 纳米微粒为前驱体 ,首次在高压高温 (3 .1 GPa,1 0 73 K)下合成了单相 Ce0 .5Zr0 .5O2 面心立方固溶体 .使用 X射线衍射、TG-DTA、XPS、Raman、电子自旋共振谱和交流阻抗谱等对样品的结构、Ce离子的价态和导电性进行了表征 .实验结果表明 ,纳米 Ce O2 -50 % Zr O2 混合物在高压 (0 .9GPa以上 )高温 (1 0 73 K以上 )条件下可以发生固态反应 ,高压下固溶温度明显降低 .Ce0 .5Zr0 .5O2 面心立方固溶体在 773 K以下是热稳定的 ,不发生结构转变 ,固溶体中 Ce离子完全以 Ce4 + 形式存在 ,773 K退火也不引起 Ce4 + 向 Ce3 + 转变 ,晶格中氧缺位非常少 .Ce0 .5Zr0 .5O2 面心立方固溶体是离子导电 ,82 3 K时电导率 σ=1 .2× 1 0 -5S/cm,与纯 Ce O2 在同温度下的电导率同数量级 ;1 1 2 3 K时 σ=2 .1× 1 0 -3 S/cm,小于掺入稀土或碱土氧化物的氧化锆和氧化铈基电解质的电导率 .在高温区和低温区 ln(σT)与 1 /T的关系满足斜率不同的二条直线 ,低温活化能小于高温活化能 .固溶体的显微硬度 (50 g载荷 )为 572 HV.     

Sm_2O_3－CeO_2－CUO三元系固线下相关系及电子型超导体Sm_（2－x

用Ｘ射线衍射法测定了Ｓｍ２Ｏ３－ＣｅＯ２－ＣｕＯ三元系固线下相关系，样品是在空气气氛１０００℃烧结的。该体系含有一个三元固溶体Ｓｍ２－ｘＣｅｘＣｕＯ４－ｙ，２个三相共存区和３个两相共存区，测定了Ｓｍ２－ｘ·ＣｅｘＣｕＯ４－ｙ固溶体的固溶限（ｘ＝０．２０），氧含量和超导电性，讨论了晶体结构和氧含量对超导电性的影响。     

Preparation and Characterization of Modified-ZrO2 Catalysts for the Reaction of Co Hydrogenation

ZrO2 in different structures and CexZr4-xO8 solid solutions have been prepared by a sol-gel related method with propionic acid as the solvent.The results of their characterization and CO hydrogenation performance eveluation show that ｔ-ZrO2 has better catalytic performance for CO hydrogenation to hydrocarbon than ｍ-ZrO2.Cerium(Ⅲ）acetate and zirconium (Ⅵ）acetylacetonate have been chosen as the most suitable starting materials for CexZr4-xO8 solid solution preparation.Ce-Zr reducibility properties are increased by the incorporation of zirconium oxide in the ceria structure.Ce2Zr2O8 exhibits a higher activity,lower methane selectivity and higher iso-C4 selectivity than tetragonal ZrO2.This implies that the formation mechanism of C4 hydrocarbons,especially that for the iso-C4 fraction is different over Ce2Zr2O8 and t-ZrO2.     

Pt/γ-Al2O3/CexZr1-xO2催化剂低温催化燃烧去除饮食油烟

以CexZr1-xO2固溶体做载体, 制备了系列Pt/γ-Al2O3/CexZr1-xO2催化剂(x=1, 0.75, 0.5, 0.25, 0). 应用Brunauer-Emmet-Teller (BET)比表面积分析、X射线衍射(XRD)和H2程序升温还原(H2-TPR)等手段对催化剂进行相关表征, 并系统研究了催化剂在饮食油烟催化燃烧中的催化活性. BET结果表明催化剂的比表面积随Ce/Zr摩尔比的减小而减小. XRD结果表明贵金属Pt很好地分散在氧化铝和CexZr1-xO2固溶体上. H2-TPR结果发现催化剂Pt/γ-Al2O3/Ce0.5Zr0.5O2的还原峰面积最大且氧离子的流动性最好. 催化活性研究结果表明Pt负载在CexZr1-xO2固溶体上有利于油烟的催化燃烧, 降低了反应温度. 随着CexZr1-xO2固溶体中Ce/Zr摩尔比的变化, 催化剂的活性顺序为Pt/γ-Al2O3/Ce0.5Zr0.5O2>Pt/γ-Al2O3/Ce0.25Zr0.75O2>Pt/γ-Al2O3/Ce0.75Zr0.25O2>Pt/γ-Al2O3/CeO2>Pt/γ-Al2O3/ZrO2.     

CH_4/CO_2重整制合成气Ni/Ce_xZr_(1-x)O_2催化剂性能研究

以水热法合成的介孔铈锆固溶体为载体,采用浸渍法制备了Ni/CexZr1-xO2催化剂,使用X射线衍射(XRD)、程序升温还原(TPR)和热重-差示扫描量热分析(TG-DSC)等测试手段对催化剂进行了表征。通过对比以ZrO2,CeO2,Ce0.6Zr0.4O2和Ce0.33Zr0.67O2为载体的Ni基催化剂性能,发现铈锆固溶体独特的氧化还原性质可以提高活性组分的分散度,增强催化剂的抗积炭性能,从而提高催化剂对甲烷二氧化碳重整制合成气的选择性。     

A full interionic potential for Na(1+x)Zr(2)Si(x)P(3-x)O(12) superionic conductors

Most inorganic solids are made up of octahedral and tetrahedral units interconnected to give an infinite framework. Use of computer simulation to study these materials has not been as prevalent as in the organic or biomolecules. Na(1+x)Zr(2)Si(x)P(3-x)O(12) is a typical inorganic solid with ZrO(6) octahedra and (Si/P)O(4) tetrahedra which are shown along with a few Na(+) sites marked M1, M2, and M3. We report here a full interionic potential which reproduces the structure and conductivity of these solids. This augurs well for the study of other inorganic solids.     

Unusual physical and chemical properties of Cu in Ce(1-x)Cu(x)O(2) oxides

The structural and electronic properties of Ce(1-x)Cu(x)O(2) nano systems prepared by a reverse microemulsion method were characterized with synchrotron-based X-ray diffraction, X-ray absorption spectroscopy, Raman spectroscopy, and density functional calculations. The Cu atoms embedded in ceria had an oxidation state higher than those of the cations in Cu(2)O or CuO. The lattice of the Ce(1)(-x)Cu(x)O(2) systems still adopted a fluorite-type structure, but it was highly distorted with multiple cation-oxygen distances with respect to the single cation-oxygen bond distance seen in pure ceria. The doping of CeO(2) with copper introduced a large strain into the oxide lattice and favored the formation of O vacancies, leading to a Ce(1-x)Cu(x)O(2-y) stoichiometry for our materials. Cu approached the planar geometry characteristic of Cu(II) oxides, but with a strongly perturbed local order. The chemical activities of the Ce(1-x)Cu(x)O(2) nanoparticles were tested using the reactions with H(2) and O(2) as probes. During the reduction in hydrogen, an induction time was observed and became shorter after raising the reaction temperature. The fraction of copper that could be reduced in the Ce(1-x)Cu(x)O(2) oxides also depended strongly on the reaction temperature. A comparison with data for the reduction of pure copper oxides indicated that the copper embedded in ceria was much more difficult to reduce. The reduction of the Ce(1-x)Cu(x)O(2) nanoparticles was rather reversible, without the generation of a significant amount of CuO or Cu(2)O phases during reoxidation. This reversible process demonstrates the unusual structural and chemical properties of the Cu-doped ceria materials.     

Role of Zr4+ cations in NO2 adsorption on Ce(1-x)Zr(x)O2 mixed oxides at ambient conditions

Mixed oxides Ce(1-x)Zr(x)O(2) prepared by slow coprecipitation in NaOH were tested for NO(2) adsorption in dynamic conditions at room temperature. The samples were characterized before and after exposure to NO(2) by XRD, N(2)-adsorption, thermal analysis, potentiometric titration, and FT-IR. Mixed oxides show a better NO(2) adsorption capacity than the parent materials (CeO(2) and Zr(OH)(4)). This effect is linked to the presence of reduced cerium and oxygen vacancies induced by the addition of Zr(4+) cations to the structure. The results indicate that NO(2) reacts with Ce(3+) to form nitrite and nitrate species on the surface. The NO retention increases with an increase in the Zr(OH)(4) content. A decrease in the density of -OH groups on the surface after the exposure to NO(2), suggests their involvement in reactive adsorption of NO and/or NO(2). From the structural point of view, no real difference was observed on the Ce(1-x)Zr(x)O(2) materials before and after exposure to NO(2).     

Photophysical and photocatalytic properties of Ca(1-x)BixVxMo(1-x)O4 solid solutions

New solid solutions with the composition of Ca(1-x)BixVxMo(1-x)O4 prepared by a solid-state method were found as novel photocatalysts with enhanced activity for O(2) evolution from aqueous solutions containing sacrificial reagent AgNO3 under visible-light irradiation (>420 nm). The obtained solid solutions crystallized in tetragonal crystal structures, except one of the end compounds, BiVO4, which crystallized in monoclinic structures. The diffuse reflection spectra of the solid solutions shift monotonically to a long wavelength as the ratio of Bi (V) ions to Ca (Mo) ions increases in the solid solution. The band structure and the dependence of the photocatalytic properties were discussed in relation to the solid-solution compositions and photophysical properties.     

Solid state NMR characterization of individual compounds and solid solutions formed in Sc(2)O(3)--V(2)O(5)--Nb(2)O(5)--Ta(2)O(5) system

In this study, (51)V, (45)Sc and (93)Nb MAS NMR combined with satellite transition spectroscopy analysis were used to characterize the complex solid mixtures: VNb(9(1-x))Ta(9x)O(25), ScNb((1-x))Ta(x)O(4) and ScNb(2(1-x))Ta(2x)VO(9) (x = 0, 0.3, 0.5, 0.7, 1.0). This led us to describe the structures of Sc and V sites. The conclusions were based on accurate values for (51)V quadrupole coupling and chemical shift tensors obtained with (51)V MAS NMR/SATRAS for VNb(9)O(25), VTa(9)O(25) and ScVO(4). The (45)Sc NMR parameters have been obtained for Sc(2)O(3), ScVO(4), ScNbO(4) and ScTaO(4). On the basis of (45)Sc NMR and data available from literature, the ranges of the (45)Sc chemical shift have been established for ScO(6) and ScO(8). The gradual change of the (45)Sc and (51)V NMR parameters with x confirms the formation of solid solutions in the process of synthesis of VNb(9(1-x))Ta(9x)O(25) and ScNb((1-x))Ta(x)O(4), in contrast to ScNb(2(1-x))Ta(2x)VO(9). The cation sublattice of ScNb((1-x))Ta(x)O(4) is found to be in octahedral coordination. The V sites in VNb(9(1-x))Ta(9x)O(25) are present in the form of slightly distorted tetrahedra. The (93)Nb NMR parameters have been obtained for VNb(9)O(25).     

Pt/γ-Al2O3/CexZr1-xO2催化剂低温催化燃烧去除饮食油烟

以CexZr1-xO2固溶体做载体,制备了系列Pt/γ-Al2O3/CexZr1-xO2催化剂(x=1,0.75,0.5,0.25,0).应用Brunauer-Emmet-Teller(BET)比表面积分析、X射线衍射(XRD)和H2程序升温还原(H2-TPR)等手段对催化剂进行相关表征,并系统研究了催化剂在饮食油烟催化燃烧中的催化活性.BET结果表叫催化剂的比表面积随Ce/Zr摩尔比的减小而减小.XRD结果表明贵金属Pt很好地分散在氧化铝和CexZr1-xO2固溶体上.H2-TPR结果发现催化剂Pt/γ-Al2O3/Ce0.5Zr0.5O2的还原峰面积最大且氧离子的流动性最好.催化活性研究结果表明Pt负载在CexZr1-xO2固溶体上有利于油烟的催化燃烧,降低了反应温度.随着CexZr1-xO2固溶体中Ce/Zr摩尔比的变化,催化剂的活性顺序为Pt/γ-Al2O3/Ce0.5Zr0.5O2＞Pt/γ-Al2O3/Ce0.25Zr0.75O2＞Pt/γ-Al2O3/Ce0.75Zr0.25O2＞Pt/γ-Al2O3/CeO2＞Pt/γ-Al2O3/ZrO2.